LOREX Technology L200 User Manual
Skill Level
Time
under 30 minutesunder 15 minutes under 60 minutes
Hand Tools Hardware
Router
Hi Speed
over 60 minutes
under 30 minutesunder 15 minutes under 60 minutes
Hand Tools Hardware
Router
Hi Speed
over 60 minutes
Time
Basic Installation Guide
Tools
Skills - Easy
L200 Series
Quick Start Guide
PACKAGE CONTENTS & MENU CONTROLS:
System Contents:
1 x Digital Video Recorder*
1 x Power Adaptor
1 x Power Adaptor Cable
1 x Remote Control
1 x Hardware Manual
1 x Quick Start Guide
1 x Software CD
*Channel/ Port conguration and Hard
drive capacity may vary by model.
Check your package for specic content information.
Cameras and Monitor are required to view DVR images. Not included.
Broadband Router and Computers are Required (for local and remote
monitoring), not Included.
Picture of a 8 Channel (L208 Series) DVR is shown
For detailed setup information,
please refer to your User’s manual.
STEP 1 - SET UP YOUR DVR FIRST
THE DEFAULT DVR PASSWORD IS 111111
NAVIGATION CONTROLS/ENTER:
• Press the navigation controls to move Up, Down, Left and Right in the
Main Menu and Search menus.
• Press the ENTER Button to select and change the values in a menu.
• Pressing the ENTER Button when displaying live video will change the
on screen view to 8 Channel View (L208 Series Only).
VGA VIDEO OUTPUT (Optional
Connection) - Video Output
port to connect the unit to a
Optional Connections
Computer Monitor.
USING THE VIRTUAL KEYBOARD:
The Virtual Keyboard control becomes available when keyboard input is needed for
entering information such as Names, Network Information, etc.
• Includes a~z, A~Z, 0~9 and Symbols: !@#$%^&*()_+{}<>?-=[];,./
• Navigate using the arrow keys on the Front Panel or Remote Control.
• Use the ENTER Button to choose the letters, numbers and symbols
• Press the Menu/Exit button once the setup is completed
Under 20 Minutes*
* Installation time may vary based
on application and camera cabling
BNC VIDEO OUT - Video
Output port to connect the
unit to another recording
device or monitor
Hand Tools Plug & Play connectors,
PS/2 - (Optional Connection)
- PS/2 port to connect a serial
Mouse to the DVR unit. Used
for mouse navigation of the
menus.
On screen set up
USB PORT - Provides con-
nection port for USB Flash
Drives (thumbsticks).
BACK PANEL OF A 8 CHANNEL VERSION IS SHOWN
Connect Cameras & Monitor (not included) to
the DVR:
Connect the rst camera (with BNC connection
type. Requires additional power adaptor) to the
CH1 input. Follow the same step to connect the
additional cameras*.
* NOTE: Test the cameras prior to selecting a permanent
mounting location by temporarily connecting the Cameras
and Cables to your DVR.
L200 Series Quick Start Guide_R1 Page 1
1
2
Connect Ethernet Cable:
Connect one end of the ethernet cable to one of the
router’s (not included) LAN PORTS and the other end to
DVR’s Network Port located at the back of the DVR. See
picture below showing a generic LAN/WAN connection.
LAN (LOCAL AREA NETWORK)
BACK OF THE ROUTER
TO YOUR DVR
TO YOUR COMPUTER
WAN (WIDE
AREA NETWORK)
Connect Power Cable:
Connect one end of the Power cable to
the DVR, the other end to an electrical
outlet. This unit powers ON once the
MASTER POWER BUTTON at the back of
the DVR is turned ON.
3
FRONT PANEL OF A 8 CHANNEL VERSION IS SHOWN
4
have successfully com-
view (when connected
Set the Time and Date:
Press the MENU button from
the front panel of the DVR (you
may use your remote control or Mouse (optional)) to view
the Setup Menu. On the Setup Menu, scroll down using the
arrow key and select System Menu and press Enter. On
the System Menu, scroll down to Time Set and press Enter.
Note: Default time is set to Eastern Standard Time. You should
change the time based on your regional settings.
Scroll down to Time Set menu to change Date and Time and
move to APPLY to apply the changed settings. Once you are
nished with the settings, press the Menu button to access
the DVR menus.
DVR - REMOTE CONTROL
www.lorexcctv.com
Congratulations! You
pleted Step 1. Your
DVR is now ready to
use. You can now
to a camera and a
monitor), record and
playback images on
your DVR.
Basic Installation Guide
Router
Hi Speed
over 60 minutes
Hi Speed
over 60 minutes
Time Skills - Intermediate
Hardware
STEP 2 - SET UP LOCAL VIEWING ON YOUR PC
Your DVR must be connected to a Router prior to powering it ON
Record the IP and MAC Addresses in the section below:
IP ADDRESS : . . .
MAC ADDRESS : : : : : :
(needed to register for DDNS)
REMOTE CONTROL
1
DVR FRONT PANEL - ENTER BUTTON
On your
Local Computer
Plug & Play connectors, On
screen set up
Under 30 Minutes*
* Installation time may vary
based on application
Computer & Router*
* Minimum System Requirement:
Windows XP, Pentium IV, 256MB Ram
(512MB Recommended), 200MB Storage, Internet, DSL or Cable modem
2 3
Retrieve System Information:
To retrieve the System Information, press the REW
button on the Remote Control (ensure batteries
are inserted) (OR) Press the REW button on the
front panel of the DVR (please check the user’s
manual for MENU steps).
4
Enter the DVR Connection Information:
Enter the IP address (recorded in Step 2-1) and DVR password information and press the Connect button to view
the Local Live Site.
REW BUTTON – Opens the System Information
window (in live view mode), and Reverses the
playback of the selected Video (2x,4x,8x).
Run the Lorex Client Software:
(on your Local Computer - not included)
Lorex Client.EXE is included within the software CD
provided with your system.
Click the Lorex Client Button on the softwre CD to
save the EXE le to your computer’s desktop. Double
click the exe le to run the software.
Connect to the DVR:
Conrm that the Lorex Client
is displaying the Viewer screen.
Click on the Connect button
located in the lower left side of
the screen.
Congratulations! You
have successfully com-
pleted Step 2. You can
now view, playback
images and remotely
control your DVR on
your local computer
over the Local Area
Network (LAN).
L200 Series Quick Start Guide_R1 Page 2
Local Live Site
www.lorexcctv.com
Loading...