LOREX Technology CVS1000 User Manual
4. Camera Specifications
Specifications:
Image Sensor 1/3” Color CCD Sensor
Video Format / Pixels
Horizontal Resolution
Sync. & Scan. Systems
S/N Ratio
Iris & Shutter Speed AES; 1/60 ~ 1/100,000 sec.
Minimum Illumination
Video Output
Lens / Focal Length /
Aperture / Mount
FOV (diagonal)
Termination
IR / Night Vision Range
Power Requirement 12V DC ±10%
NTSC: 510(H) x 492 (V)
420 TVL
Internal; 2:1 Interlace
> 52dB (without AGC)
0.05 LUX (IR Off) / 0 LUX (IR
LEDs ON)
Comp. 1.0 Vpp @ 75ohm
3.6mm F2.0/ Fixed
79 Degrees
Video: BNC Female
Power: Barrel Female
30IRLED/850nm/66’(20m)
It’s all on the web
Product Information
User Manuals
Quick Start Guides
Specification Sheets
Software Upgrades
Firmware Upgrades
COLOR SUBMERSIBLE NIGHT
VISION CAMERA
Model: CVS1000
Power Consumption
Operating Temp.
Weight (with stand) 3.7 lbs / 1.68 kg
Dimensions (with stand
and sunshade)(W x D x H)
340mA max
14°F ~ 122°F
(-10°C ~ 50°C)
3.5” x 2.75” x 5”
9cm x 7cm x 13cm
Dimensions:
VISIT
www.lorexcctv.com
Quick Set-up Guide
English Version 2.0
LOREX Technology Inc.
Copyright © 2008 LOREX Technology Inc. As our
products are subject to continuous improvement,
LOREX and its subsidiaries reserve the right to modify product design, specifications and prices, without
notice and without incurring any obligation. E&OE
1. Package Contents 2. Installing the Video Camera 3. Connecting the Camera
1 x Color Submersible
Night Vision Camera with
100’ Reinforced Video /
Power Extension Cable
1 x Mounting Bracket /
Stand
1 x AC Adaptor
1 x BNC to RCA Adaptor
WARNING - REGULATED 12V DC 1000mA power supply is
REQUIRED for use with this camera. Use of a non-regulated,
non-conforming power supply can damage this product and will void
the warranty.
1. Mount the camera stand to the desired mounting
surface.
2. Attach the camera to the supplied stand.
3. Run the cable from the Camera to the desired
connection device.
BNC (VIDEO)
(Yellow Connector)
POWER
(Red Connector)
4. Connect the BNC end of the Camera Cable to the
DVR / Observation System or to a TV/VCR.
Connect the BNC to RCA Adaptor as needed to
allow for proper connectivity.
5. Connect the AC Adaptor to the Camera cable
(Red connector). Plug the Power adaptor to a wall
outlet
Features:
• IP68 * Rated Weatherproof/Waterproof Camera
• Submersible Up To Depths of 166ft (50m)
• 1/3” CCD Image Sensor Ensures Exceptional
Picture Quality
• Built-in 3.6mm Wide Angle Lens
• IR Night Vision Ensures Vision Even In Zero Light
Environments **
• Night Vision Capability - up to 66 ft. (20m) **
* The IP68 Rating ensures complete waterproofing up to 166ft
(50m) depth (under pressure). The camera is not designed for use
in salt water or water containing chemicals (e.g. swimming pools)
** IR Illumination Range - Not Submersed: 66 ft. (20m) under
ideal conditions. Objects at or beyond this range may be partially or
completely obscured, depending on the camera application.
IR Illumination Range - Submersed: underwater is approximately
6’ (2m) in clear water not containing particulate, without additional
illumination. To extend low light visibility underwater, it is
recommended to use a secondary light source (i.e. Floodlighting).
Setup Diagram:
NOTE: CAMERA CONNECTIONS & CABLE -
The BNC and Power cable is hardwired into the
Camera. Altering this cable (cutting, resizing, etc.) will
damage the waterproof rating and will invalidate the
camera warranty.
If an additional extension cable is to be used, the
connection between the camera cable and extension
cable must be waterproofed (if the connection
between the cables is under water).
Loading...