Lorex Vantage MCB7041 Quick Start Manual

FOR SUPPORT AND INFORMATION,

VISIT WWW.LOREXTECHNOLOGY.COM

Product Information

User Manuals

Quick Start Guides

Specification Sheets

Software Upgrades

Firmware Upgrades

Contents

• IR Night Vision Camera

• Mounting Kit / Allen Key

• BNC / power extension cable

• Power adapter*

* A “4-in-1” Power Adapter that provides power to four cameras may be substituted for four
individual power adapters, depending on product configuration.
NOTE: Extension cables and power adapters may be packaged separately.

Copyright © 2013 Lorex Technologies Inc.
As our products are subject to continuous improvement, Lorex reserves the right to modify product
design, specifications and prices, without notice and without incurring any obligation. E&OE

Camera Specifications

Image Sensor 1/3” Sony EXview™ II 960H

Video Format NTSC

Effective Pixels H: 976 V: 494

Resolution up to 700 TV Lines

Scan System 2:1 Interlace

Sync System Internal

S / N Ratio >50dB (AGC Off)

Iris AES

AES Shutter Speed 1/60 ~ 1/100,000 Sec.

Min. Illumination 0.15 Lux without IR LED

0 Lux with IR LED

Video Output Composite 1.0Vpp @ 75ohm

Lens / Lens Type 3.6mm F2.0 / Fixed

FOV (Diagonal) 90°

Termination BNC Type

IR LED Qty. / Type 18 pieces / 850nm

Night Vision Range* 120ft (37m) / 85ft (26m)

Power Requirement 12V DC ±10%

Power Consumption Max. 370mA (w / IR)

Operating Temp. Range 14° ~ 122°F / –10° ~ 50°C

Operating Humidity Range < 80% RH

Indoor/Outdoor** Both (IP66)

Weight (including stand) 0.6lbs / 0.2kg

* Stated IR illumination range is based on ideal conditions in typical outdoor night time ambient
lighting and in total darkness. Actual range and image clarity depends on installation location,
viewing area and light reflection / absorption level of object.
** Not intended for submersion in water. Installation in a sheltered location recommended.

WARNING - A REGULATED UL / CSA APPROVED power supply is

REQUIRED for use with this camera. Use of a non-regulated, non-conforming
power supply can damage this product and voids the warranty.

Warning/Caution

• Read this guide carefully and keep it for future reference

• Follow all instructions for safe use of the product and handle with care

• Use the camera within given temperature, humidity and voltage levels

noted in Camera Specifications

• Do not disassemble the camera

• Do not point the camera directly towards the sun or a source of intense

light

• Use only the supplied regulated power supply. Use of a non-regulated, non­conforming power supply can damage this product and voids the warranty

• Periodic cleaning may be required. Use a damp cloth only. Do not use
harsh cleaners or aerosol cleaners

• The supplied extension cable is rated for surface mounting only

• Cables for in-wall / floor-to-floor installations are sold separately

Installation Tips

• Point the camera where there is the least amount of
obstructions (i.e. tree branches)

• Install the camera in a location that is difficult for vandals
to reach

• Secure cabling so that it is not exposed or easily cut

• Camera rated for outdoor use. Installation in a sheltered

location recommended

SUPER+ RESOLUTION WEATHERPROOF

NIGHT VISION SECURITY CAMERA

Quick Start Guide

English Version 1.0

MCB7041

153mm / 6.0”

53mm / 2.1”

Dimensions

57mm / 2.2”

Features

• 960H resolution capable*

• Advanced Sony EXview™ II image sensor

• Video image processor delivers up to 700TV lines of

resolution

• Wide angle 3.6mm lens (90° Field of View, diagonal)

• ClearNight imaging technology ensures clear night vision

and improves recording efficiency up to 30%

• Night Vision up to 120ft away in ambient lighting
conditions and up to 85ft away in total darkness**

• Split glass design minimizes IR reflection

• Weatherproof (IP66) rated housing for indoor/outdoor

installations***

• Cable pass-through bracket

Disclaimers:

* When connected with 960H capable DVR.
** Stated IR illumination range is based on ideal conditions in typical outdoor night time ambient
lighting and in total darkness. Actual range and image clarity depends on installation location,
viewing area and light reflection / absorption level of object.
*** Not intended for submersion in water. Installation in a sheltered location recommended.

Setup Diagram

Connect a BNC-to-RCA Adapter (not included, Lorex model#
BNCB) to connect the extension cable to RCA inputs (i.e. for a TV
connection).

Power Adapter Types

Individual Power Adapter

4-in-1 Power Adapter

A “4-in-1” Power Adapter that provides power to four cameras or
individual power adapters may be provided, depending on product
configuration.

Before installing the camera:

• Decide whether to run the
cables through the wall /
ceiling (drilling required) or
along the wall / ceiling.

• If you run the cables along
the wall / ceiling, you must
run the cable through the
cable notch on the base.
This will keep the camera
base flush to the wall /
ceiling when mounted.

To install the camera:

1. Set the camera in the desired mounting
position and mark holes for the screws.

2. Drill the holes, then feed the cable through the
mounting surface or cable notch and mount
the camera stand to the surface using the
provided screws.

Installing the Camera

ATTENTION - Test all connections and ensure the camera is working

correctly prior to permanent installation by temporarily connecting the
camera(s) and cable(s) to the viewing / recording solution.

Cable Notch

3. Set the position and angle of the camera using
the provided Allen key.

1) Loosen the allen screw
near the base and rotate the
base to adjust the camera’s
horizontal position.

2) Loosen the middle screw
and adjust the camera’s
vertical position.

1

2

Connecting the Camera to a TV

3

3) Loosen the screws near the
camera if you need to twist
the camera around the stand.

After setting the
camera’s position,
make sure to securely
tighten all the screws.

To Camera:

To Monitor/DVR:

Male Power

BNC

1. Connect the BNC and
power connectors to the
camera.

Female Power

2. Connect the BNC connector to
the video input of the monitor /
DVR.

3. Connect the power connectors
to the 4-in-1 power adapter. OR
Connect each camera to an
individual power adapter. See
Power Adapter Types for details.

Connecting the Camera Cable Extension Options

Extend the cable run for your camera up to 300ft or more
depending on the cable type used. See table below:

Option Cable Type Max Cable

Run Distance

Max # of

Extensions

1 Regular BNC

(sold separately)

180ft / 55m 3

2 ‘RG59’ or ‘Coax’ or

‘Coaxial BNC’
(sold separately)

300ft / 92m 5

3 Lorex Universal Cable

(sold separately)

300ft / 92m 3

Notes:

1. For optimal performance, consider using option 2 or 3. It is best to use
the same cable type for the entire distance.

2. Cable run recommendation based on typical camera power consumption
(up to 500mA). For specialty cameras with higher current consumption,
maximum cable run may be reduced. Consider providing power to the
camera at the camera side, rather then at the end of the extension cable.

3. Indicators that your cable run may be too long:

• Video is permanently black & white (even during day time)

• Video is distorted

Problem Solution

No picture / signal •Ensure your TV is on the correct input channel.

Common terms of an input channel: INPUT, AV
CHANNEL, LINE1, LINE2, AUX.

•If your camera is connected to a VCR / DVR,
ensure it is properly connected to your TV /
Monitor.

•Ensure connections are properly connected.

•Ensure the camera power supply is plugged in.

Picture is too bright •Ensure your camera isn’t pointed directly at a

source of light (e.g. sun or spot light).

•Slide the sunshade (bullet cameras featuring
adjustable sunshades only) forward to block
excess light.

•Move your camera to a different location.

Picture is too dark •If using during the day, the camera may not be

getting enough light. Slide the sunshade (bullet
cameras featuring adjustable sunshades only)
backwards to let in more light.

•Check the brightness and contrast settings
of the device your camera connects to (TV /
Monitor / DVR).

Night vision is not
working

•The night vision activates when light levels
drop. The area may have too much light.

Picture is not clear •Check the camera lens for dirt, dust,

spiderwebs. Clean the lens with a soft, clean
cloth.

•Make sure that the cable run is within the
limitations specified in the section ‘Cable
Extension Options’.

Bright spot in video
when viewing camera
at night

•Night vision reflects when pointing a camera
at a window. Move the camera to a different
location.

BNC connection does
not connect to my TV.

•Use a BNC-to-RCA adapter at the end of the
extension cable.

Troubleshooting