Lorex Vantage LDC6011PK2 Quick Start Manual

FOR SUPPORT AND INFORMATION,

VISIT WWW.LOREXTECHNOLOGY.COM

Product Information

User Manuals

Quick Start Guides

Specification Sheets

Software Upgrades

Firmware Upgrades

Contents

•Indoor IR dome camera*

•Mounting screws x 3*

•60ft BNC / power extension cable*

•BNC female / RCA male adapter**

•Power adapter*

92mm
/ 3.6”

Copyright © 2012 Lorex Technologies Inc.
As our products are subject to continuous improvement, Lorex reserves the right to modify product
design, specifications and prices, without notice and without incurring any obligation. E&OE

Camera Specifications

Image Sensor 1/3” Color Image Sensor

Video Format NTSC

Effective Pixels H: 720 V: 480

Resolution 600 TV Lines

Scan System 2:1 Interlace

Sync System Internal

S / N Ratio 48dB (AGC Off)

Iris AES

AES Shutter Speed 1/60 ~ 1/25,000 sec.

Min. Illumination 0.1 Lux without IR LED

0 Lux with IR LED

Video Output Composite 1.0Vpp @ 75ohm

Lens / Lens Type 3.6mm F2.0 / Fixed

FOV (Diagonal) 78°

Termination BNC Type

IR LED Qty. / Type 10 pieces / 850nm

Night Vision Range* 50ft / 15m

Power Requirement 12V DC ±10%

Power Consumption Max. 240mA (w / IR)

Operating Temp. Range 14° ~ 122°F / –10° ~ 50°C

Operating Humidity Range < 90% RH

Environmental Rating** Indoor use only

Weight (including stand) 0.4lbs / 0.2kg

* IR Illumination Range under ideal conditions. Objects at or beyond this range may be partially or
completely obscured, depending on the camera application.
** Not for outdoor use.

WARNING - A REGULATED UL / CSA APPROVED power supply is

REQUIRED for use with this camera. Use of a non-regulated, non-conforming
power supply can damage this product and voids the warranty.

Features

• Super resolution with enhanced optics delivering crystal clear
video at 600TV lines of resolution

• BrightNight viewing with enhanced low-light image sensor

• Close-up recognition at night with auto-light compensation

prevents wash-out effect

• Anti-glare feature ensures clear images under strong lighting
conditions

• Accurate colors with Lorex’s automatic light filtering technology

• Night vision up to 50ft (15m) away in total darkness*

• See more with 3.6mm wide angle viewing lens (78° FOV)**

Disclaimers:

* Infrared illumination range under ideal conditions. Actual range and clarity may vary
depending on scene / object reflection and camera application.
** Field of View, diagonal

Warning/Caution

• Read this guide carefully and keep it for future reference

• Follow all instructions for safe use of the product and handle

with care

• Use the camera within given temperature, humidity and voltage
levels noted in Camera Specifications

• Do not disassemble the camera

• Do not point the camera directly towards the sun or a source of

intense light

• Use only the supplied regulated power supply. Use of a non­regulated, non-conforming power supply can damage this
product and voids the warranty

• Periodic cleaning may be required. Use a damp cloth only. Do
not use harsh cleaners or aerosol cleaners.

• The supplied extension cable is rated for surface mounting only

• Cables for in-wall / floor-to-floor installations are sold separately

Installation Tips

• This camera is for indoor use only

• Point the camera where there is the least amount of obstructions

• Install the camera in a location that is difficult for vandals to

reach

• Secure cabling so that it is not exposed or easily cut

SUPER RESOLUTION INDOOR

NIGHT VISION DOME CAMERA

Quick Start Guide

English Version 2.0

LDC6011 SERIES

63mm / 2.4”

Dimensions

*Model LDC6011PK2 is a 2-pack that includes two of the listed items.
** Only included with single-camera configurations.

ATTENTION - This camera includes an Auto Mechanical IR Cut Filter. When

the camera changes between Day/Night viewing modes, an audible clicking
noise may be heard from the camera. This clicking is normal, and indicates
that the camera filter is working.

92mm / 3.6”

Cable Notch

Attach a BNC to RCA adapter* (optional, Lorex model # BNCB) to
connect the extension cable to RCA inputs (i.e. for a TV connection).

*Only included with single-camera configurations.

BNC to RCA Adapter (Optional)

To Camera: To Monitor/DVR:

Male Power

BNC

Connect the BNC and power
connectors to the camera

Female Power

Connect the BNC connector to
the video input of the monitor /
DVR, and connect the included
power connector to a power
adapter. See Setup Diagram
below for details.

Setup Diagram

Camera Base

Before installing the camera:

• Decide whether to run the
cables through the wall /
ceiling (drilling required) or
along the wall / celing.

• If you run the cables along
the wall / ceiling, you must
run the cable through the
cable notch on the base.
This will keep the camera base flush to the wall / ceiling
when mounted.

To install the camera:

1. Twist the dome cover counterclockwise to
loosen. Remove the dome cover.

2. Feed the BNC / power cable through the
camera base. If you are running the cables
against a wall or ceiling, make sure to pass
the cable through the cable notch as shown
above.

3. Mount the camera base to the wall or ceiling
using the included screws.

4. Position the Ball Camera to the desired
position and angle.

5. Position the dome cover over the ball camera
and turn clockwise to lock into place.

6. Remove the protective film on the camera
lens.

Installing the Camera Connecting the Camera Cable Extension Options

Extend the cable run for your camera up to 300ft or more depending
on the cable type used. See table below:

Option Cable Type Max Cable

Run Distance

Max # of

Extensions

1 Regular BNC

(supplied with camera)

180ft / 55m 3

2 ‘RG59’ or ‘Coax’ or ‘Coaxial

BNC’
(sold seperately)

300ft / 92m 5

3 Lorex Universal Cable

(sold seperately)

300ft / 92m 3

Notes:

1. For optimal performance, consider using option 2 or 3. It is best to use the
same cable type for the entire distance.

2. Cable run recommendation based on typical camera power consumption
(up to 500mA). For specialty cameras with higher current consumption,
maximum cable run may be reduced. Consider providing power to the
camera at the camera side, rather then at the end of the extension cable.

3. Indicators that your cable run may be too long:

• Video is permanently black & white (even during day time)

• Video is distorted

ATTENTION - Test all connections and ensure the camera is working

correctly prior to permanent installation by temporarily connecting the
camera(s) and cable(s) to the viewing / recording solution.

Problem Solution

No picture / signal

•Ensure your TV is on the correct input channel.
Common terms of an input channel: INPUT, AV
CHANNEL, LINE1, LINE2, AUX.

•If your camera is connected to a VCR / DVR,
ensure it is properly connected to your TV /
Monitor.

•Ensure connections are properly connected.

•Ensure the camera power supply is plugged in.

Picture is too bright

•Ensure your camera isn’t pointed directly at a
source of light (e.g. sun or spot light).

•Slide the sunshade (bullet cameras featuring
adjustable sunshades only) forward to block
excess light.

•Move your camera to a different location.

Picture is too dark

•If using during the day, the camera may not be
getting enough light. Slide the sunshade (bullet
cameras featuring adjustable sunshades only)
backwards to let in more light.

•Check the brightness and contrast settings of the
device your camera connects to (TV / Monitor
/ DVR).

Night vision is not
working

•The night vision activates when light levels drop.
The area may have too much light.

Picture is not clear

•Check the camera lens for dirt, dust, spiderwebs.
Clean the lens with a soft, clean cloth.

•Make sure that the cable run is within the
limitations specified in the section ‘Cable
Extension Options’.

Bright spot in video
when viewing camera
at night

•Night vision reflects when pointing a camera
at a window. Move the camera to a different
location.

BNC connection does
not connect to my TV.

•Use a BNC to RCA adapter at the end of the
extension cable.

Troubleshooting

Note: To ensure the image is right-side up, make sure the
triangle on the outer edge of the lens window points down.