Lorex SGQ4160 Instruction Manual

Download

Page 1

COLOR QUAD PROCESSOR

Instruction Manual

English Version1.0

Please be sure to read carefully and follow all the safety information.

Keep the manual in a safe place for future reference.

MODEL:

SGQ4160

www.lorexcctv.com

Page 2

INTRODUCTION

Congratulations on your purchase of the Color Quad Processor from Lorex.

The Color Quad Processor turns any monitor into a Quad monitor with security features. Connect up to four cameras to the Quad Splitter and view all four locations simultaneously in Real-Time (30 fps). The Quad Processor is an ideal security solution for small to medium sized commercial enterprises as it allows you to use an existing monitor as a 4 Channel Observation System.

Connect the Quad Processor to a Time Lapse VCR or DVR to capture footage and enable alarm recording. You can also connect PIR motion sensors to the Quad Processor in order to have Motion Detection capability.To learn more about this system or to find out more about other products available, please visit

our website at www.lorexcctv.com

FEATURES

Color Quad Processor Features

• Turns a single screen monitor into a Quad system

• View up to 4 camera locations simultaneously in real-time

(30 fps)

• Four Alarm Inputs for connection of external PIR sensors / Magnetic Sensor

• Viewing modes: Quad*Full-Screen*Auto Sequencing

• Video Loss alarm

• Digital freeze frame

• On Screen Display: date*time*camera

• Event Log lists instances of video loss & alarms

• Picture adjustable by channel (brightness/ contrast/ color)

Page 3

SAFETY WARNING

All the safety and operating instructions should be read before the appliance is operated. The improper operation may cause irreparable damage to the appliance.

• Please lift and place this equipment gently.

• Do not expose this equipment under to direct sunlight.

• Do not use this equipment near water or in contact with water.

• Do not spill liquid of any kind on the equipment.

• Do not unplug the power connector before turn the power off correctly.

• This equipment should be operated using only the power source from standard package.

• Unauthorized repair or parts substitutions may result in fire, electric shock or other hazards.

• Do not switch the Power On & Off within short period (within 3 seconds).

• Do not attempt to service this equipment by yourself. Refer all servicing to qualified service personnel.

• This unit should be operated only from the type of power source indicated on the manufacturer’s label.

• This installation should conform to all local codes.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT

Explanation of two Symbols

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance-(servicing) instructions in the literature accompanying

the appliance.

CAUTION

RISK OF ELECTRIC SHOCK. DO NOT OPEN.

REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Page 4

TABLE OF CONTENTS PAGE

1. SYSTEM INCLUDES -----------------------------------------------------------------------------

2. FRONT PANEL CONT ROLS -------------------------------------------------------------------

3. LED INDICATORS -------------------------------------------------------------------------------

4. MENU CONTROLS ------------------------------------------------------------------------------

5. MENU OPTIONS ----------------------------------------------------------------------------------

6. BACK PANEL ---------------------------------------------------------------------------------------

7. ALARM AND VIDEO LOSS ---------------------------------------------------------------------

8. RS232 REMOTE PROTOCOL -----------------------------------------------------------------

9. TROUBLESHOOTING ---------------------------------------------------------------------------

10. TECHNICAL SPECIFICATIONS --------------------------------------------------------------

11. APPENDIX #1 – T YPI CA L CONFI G URATI ON --------------------------------------------

12. APPENDIX #2 –CONNECTION TO A PIR MOTION SENS OR ----------------------

13. APPENDIX #3 – CONNECTION TO A LOREX TIME LAPSE VCR FOR ALARM RECORDING ----------------------------------------------

4 4 5 6 6 7 8 8 9

9 10 11

14. APPENDIX #4 –PIN CONFIGURATIONS FOR CONNECTION TO PC ------------

Page 5

SYSTEM INCLUDES

12V DC Power Supply

Color Quad Splitter

CHECK YOUR PACKAGE TO MAKE SURE THAT YOU RECEIVED THE COMPLETE SYSTEM, INCLUDING THE COMPONENTS SHOWN ABOVE.

9 Pin Alarm

Connector

Owner’s Manual

FRONT PANEL CONTROLS

1 2 53 4 6 7 8

MENU / ESC

Pressing this button performs the following functions:

1) Accesses the Menu screen;

2) Confirms selections when editing options in Menu mode;

3) Exits the Menu screen.

/ ( ▲ )

Pressing this button goes to Full-Screen display of Camera 1. It also serves as the Up arrow key in Menu mode.

/ ( ▼ )

Pressing this button goes to Full-Screen display of Camera 2. It also serves as the Down arrow key in Menu mode.

/ ( ◄ )

Pressing this button goes to Full-Screen display of Camera 3. It also serves as the Left arrow key in Menu mode.

/ ( ► )

Pressing this button goes to Full-Screen display of Camera 4. It also serves as the Right arrow key in Menu mode.

Page 6

QUAD / ( + )

Pressing this button goes to Quad display. It is also used to increase values when making selections in Menu mode.

AUTO / ( - )

Pressing this button initiates automatic sequencing between four all camera locations, in the following screen order: CH1 Æ CH2 Æ CH3 Æ CH4 Æ QUAD Æ CH1 …….. Note: Sequencing will automatically bypass a channel with a video loss.

VCR / FREEZE / ENTER

This button performs the following functions:

1) Press and hold this button for 3 seconds in order to enter VCR mode.

2) For the Freeze feature, press this button once. The screen will change to Quad mode, and the word “FREEZE” will appear in the top-right corner. Press a channel button, and that corresponding channel’s screen will freeze with the letter “Z” appearing as an indicator. You can then continue to freeze and unfreeze individual channels by pressing their respective buttons. To exit Freeze mode, press the VCR PLAY / FREEZE / ENTER button a second time.

3) In Menu mode, pressing this button selects a menu option to be edited.

LED INDICATORS

Above each button is a red LED indicator, which shows the system’s status and helps to navigate in Menu mode. Below is a summary of what each red LED indicator signifies:

1 2 53 4 6 7 8

1) When in Menu mode, this red indicator illuminates.

2-5) When in Full Screen viewing, the LED that is ON is the channel being viewed (CH1 / CH2 / CH3 / CH4).

When in Freeze mode, the LED’s that are ON are the channels being frozen. During an Alarm or Video Loss, the indicator lights blink on the corresponding channels experiencing the Alarm or Video Loss.

6) This LED illuminates when in Quad viewing mode.

7) This LED illuminates when in Auto Sequencing mode.

8) This LED illuminates when Freeze mode is activated, or blinks when in VCR mode.

NOTE: In menu mode, only relevant buttons (2~8) for programming will be illuminated.

Page 7

MENU CONTROLS

Pressing the MENU button brings up the Menu screen. Outlined below are the buttons used for navigation when using the Menu.

▲and ▼: Scroll up and down through menu options; change values. ◄ and ►: Scroll sideways within a menu option that has been selected

+ and - : Increase or reduce a value of a menu option when editing it (when it is blinking). ENTER: Selects a submenu / an option in a submenu for browsing / modification MENU: Completes modification of a menu option; exits a menu

MENU OPTIONS

Upon entering the Menu, you will see the screen shown to the right. Below is a description of each Menu option:

Alarm Duration

Baud Rate

Dwell Time

Int Audible Alarm

Ext Audible Alarm

Set Time

– Set the length of the alarm time between

1~99 seconds. Use +/- buttons to increase/ decrease duration times.

– Set the speed of the remote computer’s Baud Rate

which is the rate of data transmission. Available Baud Rates are: 1200, 2400, 3600, 4800, 9600, 19200, 57600, 115200. Use +/- buttons to increase/ decrease the Baud Rate.

– Select how long a camera screen will appear in

Sequencing mode before switching to the next screen. Programmable between 1~30 sec. Use +/- buttons to increase / decrease the Dwell time.

– Activates / deactivates the alarm buzzer function of the Quad Processor.

Use the ◄ / ►buttons to set On / Off.

– Activates / deactivates the Alarm OUT function for external alarm devices.

Use the ◄ / ►buttons to set On / Off.

– Allows you to program the time. Use the ◄ / ►buttons to move positions, and +/- buttons to change.

( MENU )

►ALARM DURATION: 02 SEC

BAUD RATE: 9600 BPS DWELL TIME: 02 SEC INT AUDIBLE ALARM: ON OFF EXT AUDIBLE ALARM: ON OFF SET TIME: YY:MM:DD:HH:MM:SS DWELL SETUP (CH 01): ON OFF ALARM POLARITY (CH 01): HIGH LOW OFF CAMERA TITLE SETUP (CH 01): CH1 EVENT LIST VIDEO SET SYSTEM RESET

Dwell Setup

Alarm Polarity

– Activate / deactivate by channel which cameras will be seen in Auto Sequencing. Use ▲/ ▼buttons to

select channel and ◄ / ►buttons to select On / Off.

– Select the Alarm Input for each PIR motion sensor from LOW, HIGH or OFF per channel.

LOW is the equivalent of Normally Open. HIGH is the equivalent of Normally Closed. OFF disables the PIR Alarm feature. The setting is defaulted to LOW. Use ▲/ ▼buttons to select channel and ◄ / ►buttons to set to High / Low / Off.

Note: Leave the Alarm Polarity at LOW or OFF for channels with no PIR Sensor connected.

Otherwise, you will experience a continuous alarm.

Page 8

Camera Title Setup– Change the title for each camera that appears in the On Screen Display. Use ▲/ ▼buttons to

select channel, ◄ / ►buttons to move positions, and +/- buttons to change the number or character. Alternatively, press the “Enter” button to disable the camera ID display.

Event List

– Brings up a historical record of Video Loss and Alarm occurrences. For more information on

Video Loss and Alarm, refer to page 8.

Video Set

System Reset

– Adjusts the picture Brightness / Contrast / Color by channel. Select Channel 1~4, then adjust the settings.

– Returns system to factory default settings.

BACK PANEL

DC 12V

500 mA

VIDEO INPUT

MONITOR ALARM

IN OUT

QUADVCR

OUT

1 2 53 4 6

POWER INPUT

Connects to the DC 12V Power Adapter (included with the system).

VIDEO IN (Channels 1-4)

Four BNC Video camera inputs, for Channels 1-4. Connect four cameras to these inputs.

VCR IN

Receives video signal from a VCR or DVR.

MONITOR OUT

Transmits video signal to a monitor (a TV or a security monitor) in Full / Quad form – depending on the setting of the Quad Processor.

QUAD OUT

Transmits video signal to a VCR or DVR in Quad format.

RS232 / ALARM INPUT / EXTERNAL ALARM OUTPUT

Connect PIR Motion Sensors / Magnetic Sensors to this terminal (refer to page 13) to enable Alarms. Alternatively, connect this terminal to a PC (refer to page 13) and control system functions via a PC.

Page 9

ALARM AND VIDEO LOSS

When an Alarm occurs, you will see the icon appear on the channel where motion detection is taking place. If you have set the Internal Audible Alarm to ON, then you will also hear a Buzzer.

A Channel that does not have a camera connected will show the icon, indicating a Video Loss. The red LED light above the channel with a Video Loss will blink. If you have set the Internal Audible Alarm to ON, then you will also hear a Buzzer when video is disconnected.

The Event List, available from the Menu and shown to the right, lists occurrences of Alarms and Video Loss.

RS232 REMOTE PROTOCOL

The RS232 / Alarm input allows you to control the Quad Processor system from your PC. In order to achieve this, you will require an RS232 COM Port communication program installed on your PC. There are many of these software programs available on the internet, some of which are free.

The remote connection on the Quad Processor uses 8 data bits, 1 start bit, and 1 stop bit. Below is an example of the data stream with the control codes shown.

CH EVENT YY/MM/DD TIME

------------------------

----CH1 VLOSS 01/02/10 12:20:15 CH2 ALARM 01/02/10 13:15:10

--- ----- --/--/-- --:-:--

ACT – OxFF

The PC keyboard simulates the Quad Processor’s keypad. For example, pressing “V” will make the Quad Processor go to VCR mode. Note that the letters are case sensitive. Below is a list of corresponding keys, and their codes:

ASCII

A Q M V F

For further instructions on connecting the Quad Processor to your PC’s RS232 port, please refer to Appendix #4.

OxCO ID

FUNCTION

AUTO QUAD MENU

VCR

FREEZE

ASCII

1 2 3 4

FUNCTION STOP – Ox7F

FUNCTION

CH1 CH2 CH3 CH4

Page 10

TROUBLESHOOTING

REMEDYPROBLEM

Unable to view cameras

No Power

Continuous Alarm

Bad picture quality after Power ON

• If you are using a TV as a slave monitor, you may need to set the channel as AUX (or sometimes referred to as “TV / Video”).

• Please check if the wiring between the monitor and the Quad Processor is correct.

• Make sure that the camera is receiving power

• Check the power source cord connections

• Check that there is power at the outlet

• Set the Alarm Polarity according to whether your PIR motion sensor is Normally Open or Normally Closed.

• If no motion sensors are connected, set that channel’s

Alarm Polarity to OFF.

• Connect the video cable on Channel 1 before Power

ON. The system will automatically detect electrical settings as PAL or NTSC.

TECHNICAL SPECIFICATIONS

Video input port 4 BNC camera inputs, 1 VCR input Video output port 1 Quad output for VCR, 1 monitor output Alarm input 4 (Normally High / Low selectable) Alarm output 1 (Normally Open output) Alarm duration 1 – 99 sec. Camera Title 10 characters Time / Date set Built-in real time clock Dwell Time 1 – 30 sec. RS-232 port Yes Load impedance 75 Ohms Operating environment 10~80%RH, 0oC~50oC Power source Power consumption 6W maximum Dimension (mm) 240(W) x 45 (H) x 150 (D) Weight 1,300g

Because our products are subject to continuous improvement SVC reserves the right to modify product designs and specifications without notice and without incurring any obligations. E & O.E

DC 12V ± 10%, 1A

Page 11

APPENDIX #1 – TYPICAL CONFIGURATION

DC 12V

500 mA

VIDEO INPUT

MONITOR ALARM

IN OUT

QUADVCR

OUT

THE COLOR QUAD HAS BNC JACKS TO CONNECT TO OTHER VIDEO SOURCES. BNC COUPLERS AND VIDEO CABLES ARE NOT INCLUDED.

Note: If using a TV as a slave monitor, it may have to be set in AUX mode (sometimes referred to as TV/Video)

Page 12

APPENDIX #2 – ALARM BLOCK CONNECTION

to PIR MOTION SENSOR

Wires from the PIR Motion Sensors must be soldered to the terminal of the 9 Pin Alarm Connector.

Each PIR Sensor connects via 2 wires: 1 to a specific Channel and the other to the Ground input. For descriptions of each contact on the 9 Pin Connector of the Quad Processor, please refer to Appendix #4.

PIR Motion Sensors

9 PIN Alarm Connector

Page 13

APPENDIX #3 – CONNECTION to a LOREX TIME LAPSE VCR FOR ALARM RECORDING

Wires being run from the Time Lapse VCR’s or DVR’s alarm input terminal must be soldered to the appropriate terminal of the 9 Pin Alarm Connector.

In addition to connecting up to 4 PIR Motion Sensors, connect the 9 Pin Alarm Connector to a security recorder such as the Lorex Time Lapse VCR shown below for Alarm Recording upon motion detection.

For descriptions of each contact on the 9 Pin Connector of the Quad Processor, please refer to Appendix #4.

4 5

MONITOR ALARM

IN OUT

QUADVCR

OUT

Page 14

APPENDIX #4 – PIN CONFIGURATIONS FOR CONNECTION TO A COMPUTER

25 PIN COM PORT

9 PIN COM PORT

Page 15

It’s all on the web

 Product Information

 User Manuals

 Quick Start Guides

 Specification Sheets

 Software Upgrades

 Firmware Upgrades

VISIT

www.lorexcctv.com

Strategic Vista International Inc.

www.lorexcctv.com