Lorex SG7570AB Quick Start Manual

Contents

• IR Night Vision Camera

• Mounting Kit / Allen Key

• 60ft BNC / RCA / Power Extension Cable

• Power Adapter

• BNC-to-RCA Adapter

WARNING - A REGULATED UL / CSA APPROVED power supply is

REQUIRED for use with this camera. Use of a non-regulated, non-conforming
power supply can damage this product and voids the warranty.

Features

• Super resolution 1/3” image sensor produces sharp and
clear video at 600 TV lines of resolution

• Built-in microphone for listen-in audio*

• Automatic Infrared Filter ensures true color in all lighting

conditions

• 3.6mm wide-angle lens captures a 79° field of view
(diagonal)

• Anti-glare feature ensures clear images under strong
lighting conditions

• Night vision range up to 60ft (18m) in total darkness,
and 85ft (26m) in ambient lighting**

• True Day/Night mode: Picture automatically switches to
B&W delivering better clarity in low light conditions

• Weatherproof Design: ideal for outdoor & indoor
applications (IP66)***

• Integrated 3ft camera cable for flexible installation and
protection from the elements

• Cable pass-through mount protects cables from vandalism

• Versatile mounting options: ceiling, counter or wall

mountable

• Energy-efficient CEC (California Energy Commission)
compliant power adapter included

Warning/Caution

• Read this guide carefully and keep it for future reference

• Follow all instructions for safe use of the product and handle with care

• Use the camera within given temperature, humidity and voltage levels

noted in Camera Specifications

• Do not disassemble the camera

• Do not point the camera directly towards the sun or a source of intense

light

• Use only the supplied regulated power supply. Use of a non-regulated,
non-conforming power supply can damage this product and voids the
warranty

• Periodic cleaning may be required. Use a damp cloth only. Do not use
harsh cleaners or aerosol cleaners.

• The supplied extension cable is rated for surface mounting only

• Cables for in-wall / floor-to-floor installations are sold separately

Installation Tips

• Point the camera where there is the least amount of obstructions (i.e. tree
branches)

• Install the camera in a location that is difficult for vandals to reach

• Secure cabling so that it is not exposed or easily cut

• Camera rated for outdoor use. Installation in a sheltered location

recommended

Camera Specifications

Image Sensor 1/3” Color Image Sensor

Video Format NTSC

Effective Pixels H: 728 V: 488

Resolution 600 TV Lines

Scan System 2:1 Interlace

Sync System Internal

S / N Ratio 48dB (AGC Off)

Iris AES

AES Shutter Speed 1/60 ~ 1/62,500 Sec.

Min. Illumination 3.0 Lux without IR LED

Video Output Composite 1.0Vpp @ 75ohm

Lens / Lens Type 3.6mm F2.0 / Fixed

FOV (Diagonal) 79°

Termination BNC Type / RCA Audio*

IR LED Qty. / Type 18 pieces / 850nm

Night Vision Range** 60ft (18m) / 85ft (26m)

Power Requirement 12V DC ±10%

Power Consumption Max. 270mA (w / IR)

Operating Temp. Range 14° ~ 122°F / –10° ~ 50°C

Operating Humidity Range < 90% RH

Indoor/Outdoor*** Both (IP66)

Weight (including stand) 0.6lbs / 0.3kg

* Audio recording without consent is illegal in certain jurisdictions. Lorex Technology Inc.
assumes no liability for use of its products that does not conform with local laws.
** Stated IR illumination range is based on ideal conditions in total darkness and in typical outdoor
night time ambient lighting. Actual range and image clarity depends on installation location, viewing
area and light reflection / absorption level of object.
*** Not intended for submersion in water. Installation in a sheltered location recommended.

0 Lux with IR LED

Dimensions

57mm / 2.2”

53mm / 2.1”

FOR SUPPORT AND INFORMATION,

VISIT WWW.LOREXTECHNOLOGY.COM

Product Information

User Manuals

Quick Start Guides

Copyright © 2013 Lorex Technologies Inc.
As our products are subject to continuous improvement, Lorex reserves the right to modify product
design, specifications and prices, without notice and without incurring any obligation. E&OE

153mm / 6.0”

Specification Sheets

Software Upgrades

Firmware Upgrades

SUPER RESOLUTION WEATHERPROOF

NIGHT VISION SECURITY CAMERA WITH AUDIO

Quick Start Guide

English Version 1.0

SG7570AB

Installing the Camera Cable Extension Options

ATTENTION - Test all connections and ensure the camera is working

correctly prior to permanent installation by temporarily connecting the
camera(s) and cable(s) to the viewing / recording solution.

Connecting the Camera

To Camera:

To Monitor/DVR:

Extend the cable run for your camera up to 180ft depending on the cable type
used. See table below:

Extends Cable Type Max Cable

Before installing the camera:

• Decide whether to run the
cables through the wall /
ceiling (drilling required) or
along the wall / ceiling.

• If you run the cables along
the wall / ceiling, you must
run the cable through the
cable notch on the base.
This will keep the camera

Cable Notch

base flush to the wall /
ceiling when mounted.

To install the camera:

1. Set the camera in the desired mounting
position and mark holes for the screws.

2. Drill the holes, then feed the cable through the
mounting surface or cable notch and mount
the camera stand to the surface using the
provided screws. Make sure all three screws
are fastened tightly at the connection points.

3. Set the position and angle of the camera using
the provided Allen key.

1

1) Loosen the allen screw
near the base and rotate the
base to adjust the camera’s
horizontal position.

3

2

2) Loosen the middle screw and
adjust the camera’s vertical position.

3) Loosen the screw near the
camera if you need to twist the
camera around the stand.

After setting the camera’s
position, make sure to
securely tighten all the
screws.

Male Power

RCA Audio

Female Power

BNC

1. Connect the BNC, power,
and RCA audio connectors
to the camera.

2. Connect the BNC connector to
the video input of the monitor /
DVR.

3. Connect the RCA connector to
the audio input of the monitor /
DVR.

4. Connect the camera to the
power adapter.

Connecting the Camera to a TV

Connect the included BNC-to-RCA Adapter (Lorex model # BNCB)
to connect the BNC video connector on the extension cable to RCA
inputs (i.e. for a TV connection).

Setup Diagram

ATTENTION - This camera includes an Auto Mechanical IR Cut Filter. When

the camera changes between Day/Night viewing modes, an audible clicking
noise may be heard from the camera. This clicking is normal, and indicates
that the camera filter is working.

Power
and
Video

Audio RCA cable (not included) 180ft / 55m 3

Notes:

1. It is best to use the same cable type for the entire distance.

2. Cable run recommendation based on typical camera power consumption

3. Indicators that your cable run may be too long:

Troubleshooting

No picture / signal •Ensure your TV is on the correct input channel.

Picture is too bright •Ensure your camera isn’t pointed directly at a

Picture is too dark •If using during the day, the camera may not be

Night vision is not
working

Picture is not clear •Check the camera lens for dirt, dust,

Bright spot in video
when viewing camera
at night

BNC connection does
not connect to my TV

Audio does not work •Make sure RCA cable is connected to the Audio

Regular BNC (supplied with
camera) OR ‘RG59’, ‘Coax’, or
‘Coaxial BNC’ (sold separately)

(up to 500mA). For specialty cameras with higher current consumption,
maximum cable run may be reduced. Consider providing power to the
camera at the camera side, rather then at the end of the extension cable.

• Video is permanently black & white (even during day time)

• Video or audio is distorted

Problem Solution

Common terms of an input channel: INPUT, AV
CHANNEL, LINE1, LINE2, AUX.

•If your camera is connected to a VCR / DVR,
ensure it is properly connected to your TV /
Monitor.

•Ensure connections are properly connected.

•Ensure the camera power supply is plugged in.

source of light (e.g. sun or spot light).

•Slide the sunshade (bullet cameras featuring
adjustable sunshades only) forward to block
excess light.

•Move your camera to a different location.

getting enough light. Slide the sunshade (bullet
cameras featuring adjustable sunshades only)
backwards to let in more light.

•Check the brightness and contrast settings
of the device your camera connects to (TV /
Monitor / DVR).

•The night vision activates when light levels
drop. The area may have too much light.

spiderwebs. Clean the lens with a soft, clean
cloth.

•Make sure that the cable run is within the
limitations specified in the section ‘Cable
Extension Options’.

•Night vision reflects when pointing a camera
at a window. Move the camera to a different
location.

•Use a BNC to RCA adapter at the end of the
extension cable.

Input on your DVR / TV / monitor.

•Make sure audio is enabled on your DVR and
that it is connected to speakers.

Run Distance

180ft / 55m 3

Max # of

Extensions