Lorex LW2101AC1 Series Quick Start Manual

CONTENTS:

COLOR DIGITAL WIRELESS INDOOR/OUTDOOR
ACCESSORy CAMERA

LW2101AC1 SERIES - QUICk START GUIDE

Before you install the camera, carefully plan where and how it will be

positioned, and where you will route the cable that connects the

camera to the power adaptor or battery pack adaptor.

Digital Wireless Color

Camera with Stand

Wireless Antenna

for camera

INSTALLATION WARNINGS

• Aim the Cameras to best optimize the
viewing area: Select a location for the
camera that provides a clear view of the
area you want to monitor, which is free
from dust, and is not in line-of-sight to a
strong light source or direct sunlight.

• Avoid installing the cameras where there
are thick walls, obstructions, or
interference (i.e. transformers, microwave
ovens or other electrical equipment)
between the Cameras and the Receiver.

• Select a location for the camera that
has an ambient temperature between
14°F~113°F (-10°C~45°C)

• Before starting permanent installation,
have another person hold the camera
for you while you verify its performance
by observing the image on a monitor.

NIGHT VISION

This camera includes IR LEDs, which
provide the camera with the ability to view
images in low light conditions. It is important
to use the provided power adaptor (and not
the Battery Pack Adaptor) when using the
camera for prolonged periods in low light
conditions, as the LEDs will drain the battery
more quickly than regular daytime use.

Battery Pack Adaptor

Case for camera

INSTALLING THE CAMERA

1. Carefully unpack the Camera.

2. Mount the stand to the wall:

• Mark the position of the
screw holes on the wall.

• Drill holes and insert the
drywall plugs as needed.

• Firmly attach the stand
to the wall using the
provided screws.

3. Attach the Antenna to the
Camera prior to mounting.

4. Place the camera in the
desired mounting position.
Tighten the thumbscrews
to secure the camera to the
Stand. Adjust the angle of
the camera until the
desired view is set.

Power Adaptor

for camera

Quick Start Guide

www.lorexcctv.com

LW 2 101AC 1 SERI E S QSG _ EN_R1 Page 1

COLOR DIGITAL WIRELESS INDOOR/OUTDOOR
ACCESSORy CAMERA

LW2101AC1 SERIES - QUICk START GUIDE

CONNECTING CAMERA POWER

The Camera can be powered either by using the
provided Power Adaptor, or using the included Battery
Pack Adaptor (requires 4 x AA Batteries, not included).

NOTE: Wireless cameras require a power source
(either an electrical outlet or battery power) to operate.
If you plan to permanently mount the camera in a loca­tion, it is recommended to use the included Camera
Power adaptor to prevent interruptions in the image, as
the battery pack adaptor is intended as a temporary
power solution.

POWER ADAPTOR

Connect the Power Adaptor to the Female Barrel Power
termination on the Camera. Make sure the power adaptor
is placed into a grounded outlet or surge bar to protect
the camera from power fluctuations.

ADDING THE ACCESSORY CAMERA TO YOUR SYSTEM

The Pairing Function assigns each camera to a different
channel on the wireless receiver (connect up to 4 Cameras),
and is necessary for configuring additional cameras. By
default the camera that came with the LW2101 system is
assigned to channel no. 1.

NOTE: It is highly recommended to pair the Accessory
Camera to the Receiver before permanently mounting the
camera. For detailed information, please check the owners
manual for the LW2101 system available at

www.lorexcctv.com

1. Power ON the Camera by connecting the Power
Adaptor or Battery Adaptor Pack. The transmit lights on the
front of the Camera will turn ON.

2. Navigate to the PAIR CAM Menu option by pressing the

MENU Button on the Receiver, and using

the arrows keys to navigate. Select the
desired Pairing channel (channel no. 2, 3 or 4).

3. Press the Cam button . The screen will display the
following message: Please Press Pair Key on Sensor
Side and a countdown of 60 seconds will commence. The
Red indicator LED on the Receiver will start flashing.

BATTERY PACK ADAPTOR

1. Slide the cover off the Battery Pack Adaptor.

2. Insert 4 x AA Batteries (not included). Make sure to
correctly line up the Positive (+) and Negative (-)
terminals of the batteries.

Slide the Battery Pack cover back on.

3. To turn the Camera ON or OFF, simply connect or
disconnect the Battery Pack from the Camera.

NOTE: It is recommended to remove the battery pack
from the camera when not in use.

www.lorexcctv.com

4. Press the Pairing Button on the back of the Camera.
Once the Pairing has been successfully completed:

1. The Green Camera Transmit indicator LED will illuminate

2. The Red Receiver Indicator LED will stop flashing

3. The video from the Camera including information
(channel no., transmission strength, etc.) will appear
onscreen.

It’s all on the Web

For detailed setup information,
please refer to your User’s Manual.
For additional information, please
visit our website

www.lorexcctv.com/support

LW 2 101AC 1 SERI E S QSG _ EN_R1 Page 2