Lorex LW2101, LW2100 Quick Start Manual
www.lorexcctv.com
LW2100 Quick Start Guide_R1 Page 1
under 30 minutesunder 15 minutes under 60 minutes
Hand Tools Hardware
Router
Hi Speed
over 60 minutes
Skill Level
Time
under 30 minutesunder 15 minutes under 60 minutes
Hand Tools Hardware
Router
Hi Speed
over 60 minutes
Time Tools Skills - Easy
Under 15 Minutes*
Hand Tools Plug & Play connections,
On screen set up
* Installation time may vary
based on application and
camera location
ULTRA DIGITAL WIRELESS VIDEO
MONITORING SOLUTION
LW2100 - QUICK START GUIDE
NOTE: AVOID INSTALLING IN A LOCATION
WHICH REQUIRES THE WIRELESS SIGNAL
TO PASS THROUGH CEMENT, CONCRETE
AND METAL STRUCTURES. THIS WILL
REDUCE THE TRANSMISSION RANGE.
Getting Started
A. Connect the Camera
B. Connect the Receiver to an Observation System / Recorder (DVR) or TV
1
Observation Monitor or Recorder (DVR) with
BNC input:
Plug the BNC connector of the receiver directly
into the monitor or DVR.
Connect one end of the Receiver
Power Adaptor to the receiver
and the other end to an electrical
outlet.
4
TV with RCA Inputs:
Attach the included BNC/RCA adapter to the
BNC plug on the receiver. Plug the receiver into
the TV.
2
1
3
Connection Options:
Connect power adaptor to local
120V AC power outlet
Mount camera stand to the wall.
1
3
Connect one end of the camera
Power Adapter to the camera
and the other end to an
electrical outlet.
2
The System comes with a camera that has already been paired. The Pairing Function assigns each camera to a different channel on
the Wireless Receiver (up to 4 Cameras), and is necessary for configuring additional cameras. By default, the camera included with
the system appears on channels 1 on the wireless receiver. Please refer to the included Owner’s Manual for detailed steps.
C. Adding Additional Cameras
OPTIONAL
If the receiver is not able
to directly plug into your
TV or recorder because
of space constraints or
blockage of wireless
signal, use the included
BNC/BNC extension
cable to reposition the
receiver.
2
OPTIONAL
This Ultra Digital Wireless Video
Monitoring Solution comes with the
following components:
• Digital Wireless Color Camera*
• Camera Stands*
• Wireless Receiver
• Wireless Antenna’s for camera*
and receiver
• Power Adaptors for camera*
and receiver
• BNC/RCA Adapter
• BNC / BNC 3ft extension cable
• Mounting Hardware
• Instruction Manual
* Number of cameras may vary by
model. Check your package for
specific content information.
ATTENTION: Make sure to first connect
and power on the camera before powering
on the receiver; this will ensure a proper
connection.
Secure Camera to the mounting stand.
Adjust the angle of the camera until
the desired view is set. Tighten the
thumbscrews to secure the desired
camera position.
Attach the
included
Antenna to
the receiver
by screwing
it on.
NOTE: Wireless cameras require a power
source to operate.
NOTE: Before you install a camera, carefully plan where
and how it will be positioned, and where you will route the
cable that connects the camera to the power adaptor.
Before starting permanent installation, verify its
performance by observing the image on a monitor when
the camera is positioned where it will be permanently
installed.
NOTE: When adding cameras that were not
included in the original box, you will need to
pair up the camera with the receiver. Please
refer to the Camera Pairing Section of the User
Manual.
*
www.lorexcctv.com
LW2100 Quick Start Guide_R1 Page 2
It’s all on the Web
For detailed setup information,
please refer to your User’s Manual.
For additional information and
accessory purchases, please visit
our website
www.lorexcctv.com/support
REGISTER NOW!
TO RECEIVE 3 MONTHS
WARRANTY EXTENSION
Visit: www.lorexcctV.com and
click on “warranty registration”
The LW2100 product is
EXPANDABLE UP TO 4 CAMERAS*
To order additional cameras, please visit
our website at www.lorexcctv.com
D. Receiver Function Buttons
1. Wireless Antenna: Connects to the back of
the receiver.
2. Channel LEDs: When lit up, indicates
the active viewing mode.
3. Resolution* button: Press to switch
between VGA and QVGA video resolutions;
press and hold for several seconds to
remove/replace channels from Auto-Scan.
4. Front LED: Lit in green to indicate power to
the receiver.
5. Channel: Press to change channels (1~4),
enter Quad split-screen mode, and
Auto-Scan viewing mode; press and hold
to add (pair) a new camera to the receiver.
©2009 Lorex Technology Inc.
As our product is subject to continuous improvement, Lorex Technology &
subsidiaries reserve the right to modify product design, specifications, prices &
warranty without notice and without incurring any obligation. E&OE
*NOTE: You can install additional cameras (maximum of 4 cameras).
When adding cameras that were not included in the original box, you
will need to pair up the cameras with the receiver. Refer to the camera
pairing section of the included user manual for more details.
*VGA mode has a resolution of 640 x 480
pixels; QVGA mode has a resolution of 320
x 240 pixels. Use VGA mode for the best
video performance. Use QVGA mode if you
need a higher video frame rate.
1
2
43 5
EXTENDING YOUR WIRELESS SIGNAL
Even with a clear line-of-sight between your camera(s) and
your receiver, you may experience a lower frame rate simply
due to the distance between your wireless devices. Accessory
antennas are available that can help extend the range of your
wireless signal. Visit www.lorexcctv.com for more details.
ULTRA DIGITAL WIRELESS VIDEO
MONITORING SOLUTION
LW2100 - QUICK START GUIDE
Loading...