Lorex LNZ3522B Instruction Manual
Instruction
Manual
LNZ3522B HD
MICRO PT DOME
CAMERA
Instruction Manual
LNZ3522B HD MICRO PT
DOME CAMERA
#LX400043; r. 1.0/19290/23171; en-US iii
Thank you for purchasing this product. Lorex is committed to providing our customers with
a high quality, reliable security solution.
This manual refers to the following models:
LNZ3522B
For the latest online manual, downloads and product updates, and to learn about our
complete line of accessory products, please visit our website at:
www.lorextechnology.com
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO REDUCE THE RICK OF ELECTRIC SHOCK DO NOT
REMOVE COVER. NO USER SERVICABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated "dangerous voltage" within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE
THIS UNIT TO RAIN OR MOISTURE.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF
THE PLUG TO THE WIDE SLOT AND FULLY INSERT.
#LX400043; r. 1.0/19290/23171; en-US iv
Table of contents
1 Safety Instructions ..............................................................1
2 LNZ3522B Features .............................................................2
3 Getting Started ...................................................................3
4 Camera Overview ................................................................4
5 Connecting the Camera .......................................................5
5.1 OPTION 1: Connecting Cameras to an NVR.....................5
5.2 OPTION 2: Connecting Cameras to the Local Area
Network (LAN) ...........................................................5
6 Installation ....................................................................... 10
6.1 Installation Tips and Warnings..................................... 10
6.2 Installation (Indoor/Outdoor)........................................ 10
6.2.1 Ceiling Mounting............................................ 10
7 Controlling the PT Camera with an NVR ............................... 14
7.1 Controlling the Camera’s Pan-Tilt Movement (Local
NVR) ..................................................................... 15
7.2 Advanced Pan-Tilt Controls......................................... 15
7.2.1 Presets........................................................ 16
7.2.2 Tour (Not Supported) ...................................... 17
7.2.3 Pattern (Not Supported) .................................. 17
7.2.4 Border (Not Supported) ................................... 17
8 Technical Specifications .................................................... 18
8.1 Dimensions ............................................................. 19
9 Troubleshooting................................................................ 20
10 Resetting the Camera ........................................................ 22
11 Notices ............................................................................ 24
11.1 FCC/IC Notice ......................................................... 24
11.2 Modification............................................................. 24
11.3 ROHS .................................................................... 24
#LX400043; r. 1.0/19290/23171; en-US
v
Safety Instructions
1
• Read this guide carefully and keep it for future reference.
• Follow all instructions for safe use of the product and handle with care.
• Use the camera within given temperature, humidity, and voltage levels
noted in the Technical Specifications.
• Camera is rated for outdoor use and is weatherproof when properly installed. Camera is not intended for submersion in water. Installation under
a sheltered environment is recommended.
• Do not disassemble the camera.
• Do not point the camera directly towards the sun or a source of intense
light.
• Make sure to install the camera in a location that can support the camera
weight.
• Make sure there are no live electrical cables in the area where you plan to
mount the camera.
• Periodic cleaning may be required. Use a damp cloth only. Do not use anything other than water to clean the dome cover, as chemicals such as acetone can permanently damage the plastic.
#LX400043; r. 1.0/19290/23171; en-US
1
LNZ3522B Features
2
• High definition 1080p resolution 2.1 MP image sensor.
1
• Full 360° pan rotation for complete area coverage and 100° per second
panning speed.
• Micro dome form factor only 5" in diameter and just over 2" tall.
• 25 programmable preset positions.
• Built-in microphone for listen-in audio.
• Wide angle 3.6mm lens with 90° field of view.
• Single network cable setup for video, power and Pan/Tilt control.
• Program preset viewing points when connected to a compatible NVR.
1
• Remote control of the Pan/Tilt camera using a smartphone or tablet when
connected to a compatible NVR.
1
• Digital wide dynamic range backlight compensation ensures clear images
in high and low light areas.
• 3D DNR (Digital Noise Reduction) for clear accurate images.
• ClearNight imaging for superior low light performance.
2
• Weatherproof for outdoor & indoor installation (IP66 Rated).
3
• Extreme temperature performance (–4° ~ 140°F / –20° ~ 60°C).
• Vandal-proof heavy-duty durable metal housing.
• Simple installation with Power over Ethernet (PoE) CAT5e cable.
• CAT5 PoE extension cable included per camera.
• Expand your coverage with Ethernet cable up to 300’ from the NVR.
NOTE
1. Compatible with Lorex HD NVR LNR100 & LNR400 Series only.
2. This camera features an ultra-low light sensitive image sensor and therefore does not
feature Infra-Red LEDs. The camera requires ambient lighting (for example, street/
building lighting, star or moon light) to render a night time image. In total darkness
(zero Lux) the camera will not produce a night time image and therefore the camera
should not be installed in areas with complete darkness.
3. Not intended for submersion in water. Installation in a sheltered location
recommended.
#LX400043; r. 1.0/19290/23171; en-US
2
Getting Started
3
The system comes with the following components:
Micro PT Dome Camera Ethernet Extension Cable
Allen Key
Metal Mounting Plate Mounting Template
Mounting Screws &
Anchors
(for mounting plate)
Instruction Manual
#LX400043; r. 1.0/19290/23171; en-US
3
Camera Overview
4
1. Dome Cover
2. Ethernet Port: Connect the camera to an NVR or PoE switch on your net-
work using the included Ethernet cable.
3. 12V DC Power: If not using PoE, connect the camera to a 12V DC power
source (not included). Power adapters for this camera are available for
purchase on www.lorextechnology.com (model #: CVA4902).
4. Lens: Camera lens.
5. Microphone: Built-in microphone.
6. GND Port: The pre-inserted screw grounds the camera.
7. Reset Button Compartment: Open using a Phillips screwdriver to reveal
the reset button. Press and hold for 4 seconds to reset camera settings.
#LX400043; r. 1.0/19290/23171; en-US
4
Connecting the Camera
5
NOTE
It is recommended to connect the camera to your NVR and test the Pan-Tilt controls before
permanent installation. For instructions on how to setup Pan-Tilt controls, see 7 Controlling
the PT Camera with an NVR, page 14.
5.1 OPTION 1: Connecting Cameras to an NVR
1. Connect the Ethernet connector on the camera cable to the included
Ethernet extension cable.
2. Connect the Ethernet extension cable to one of the PoE ports on the back
panel of your NVR.
NOTE
You can use a single CAT5e Ethernet cable up to 300ft (91m) to connect the camera to
your NVR. The camera is compatible with Lorex LNR100 & LNR400 Series NVRs only.
5.2 OPTION 2: Connecting Cameras to the Local Area Network (LAN)
For flexibility, you may also connect the camera to the same Local Area Network (LAN) as the NVR. This is accomplished by connecting the camera to
the same router as the NVR. For these installations, an external PoE switch
(sold separately) or power adapter (not included) must be used to provide
power to the camera. You also must add the camera on the NVR before it will
show a picture on the monitor or be recorded by the NVR.
What is PoE?
PoE (Power over Ethernet) is a technology that allows Ethernet cables to carry
electrical power to connected devices. Compatible NVRs use integrated PoE
#LX400043; r. 1.0/19290/23171; en-US
5
Connecting the Camera
5
ports to provide power and Pan-Tilt commands to the camera, as well as video connection to the NVR. In order to use PoE with this IP camera, you must
connect it directly to a compatible NVR (Lorex LNR100 & LNR400 Series only) or a PoE switch on the same network as the NVR.
PoE switches are available for purchase on www.lorextechnology.com.
Complete the following steps to connect the camera to the NVR over the LAN.
Step 1 of 2 — OPTION A: Connecting the camera to your local network
using an optional PoE switch:
1. Connect an Ethernet cable of up to 300ft (91m) rated CAT5e or higher
(not included) from the LAN port on an external PoE switch (sold separately on www.lorextechnology.com) to your router. Connect the power ca-
ble to the PoE switch and to a power outlet or surge protector.
NOTE
Terminology may vary depending on the model of PoE switch you have.
2. Connect the camera to the PoE switch using the included Ethernet cable
(or a CAT5e Ethernet cable of up to 300ft (91m)). The PoE switch will provide power and video transmission the same way as your NVR.
#LX400043; r. 1.0/19290/23171; en-US
6
Connecting the Camera
5
Step 1 of 2 — OPTION B: Connecting the camera to your local network
using a power adapter (not included):
1. Connect the camera to a 12V DC power adapter (sold separately on
www.lorextechnology.com — model #: CVA4902).
2. Connect the camera to a router in the same network as your NVR using
the included Ethernet cable (or an Ethernet cable of up to 300ft (91m)
rated CAT5e or higher).
Step 2 of 2: Add the camera to your NVR:
CAUTION
The following instructions are based on the Lorex LNR400 Series NVR. See your NVR’s instruction manual for instructions on controlling the PT camera with your system.
1. Right-click and select Device Search .
2. Log in using the admin account (default User Name: admin; default Password: 000000).
#LX400043; r. 1.0/19290/23171; en-US
7
Connecting the Camera
5
3. Click Device Search. The system searches the network for compatible
cameras.
4. Check the camera(s) you would like to add.
5. Click Add. The Status indicator turns green to show the camera is successfully connected.
#LX400043; r. 1.0/19290/23171; en-US
8
Connecting the Camera
5
6. Click OK to save changes.
NOTE
You can also add a camera to a specific channel by hovering the mouse over an empty
channel in split-screen view and clicking
. Then double-click the camera you would like
to add and right click to exit.
#LX400043; r. 1.0/19290/23171; en-US
9
Installation
6
6.1 Installation Tips and Warnings
• Camera is rated for outdoor use. It is recommended to install the camera in
a sheltered area, such as under the eaves on a roof.
• Camera is capable of seeing in low light conditions (0.1 Lux), but it cannot
see in total darkness. It is recommended to install the camera where there
is some ambient light (for example, street lighting or starlight, moonlight,
etc.) or leave some lighting on in the area where the camera is installed.
• Mount the camera in a location that can support the camera weight.
• Mount the camera where the lens is away from direct and intense sunlight.
• Plan your cable wiring so that it does not interfere with power lines or tele-
phone lines.
• Ensure you adhere to local building codes.
• Ensure that the camera wiring is not exposed or easily cut.
• Mount the camera in an area that is visible but out of reach.
6.2 Installation (Indoor/Outdoor)
NOTE
The camera includes all necessary components for ceiling mounting only.
6.2.1 Ceiling Mounting
To ceiling mount the camera:
1. Use the included mounting template to mark holes for the mounting
screws and camera cable.
1. Mounting screw holes; 2. Camera cable hole
#LX400043; r. 1.0/19290/23171; en-US
10
Installation
6
2. Drill holes for the mounting screws, drywall anchors (optional) and camera
cable.
NOTE
• Use the included drywall anchors if installing on a drywall surface.
• If you are planning on running the cables along the mounting surface, there is no
need to drill a hole for the camera cable.
3. Align the metal mounting plate so that the 3 screw holes in the plate line
up with the 3 holes drilled in the ceiling. Attach the flat side of the metal
mounting plate to the mounting surface using the included mounting
screws (3x).
1. Drywall anchors (3x — optional); 2. Mounting screws (3x); 3. Mounting
surface; 4. Metal mounting plate
4. Remove the M2x5 screw from the side of the camera using the included
Allen key.
5. Connect the camera cables as shown in 5 Connecting the Camera, page
5.
#LX400043; r. 1.0/19290/23171; en-US
11
Installation
6
6. Align the 3 notches on the side of the dome camera with the pegs on the
metal mounting plate. Push the camera gently into the mounting plate until
it ‘clicks’.
CAUTION
If you are drilling a hole for the camera
cable, ensure that you run the cable
through the cable hole in the metal
mounting plate. See image below for
reference:
If you run the cables along the mounting
surface, you must run the cable through
the cable notch on the camera base
and underneath the metal mounting
plate. This will keep the camera base
flush to the surface when mounted. See
image below for reference:
1. Pegs (x3); 2. Notches (x3)
NOTE
The pegs and notches only align one way. Do not force the camera to fit into the metal
mounting plate.
#LX400043; r. 1.0/19290/23171; en-US
12
Installation
6
7. Re-insert the M2x5 screw removed in Step 4. Tighten firmly using the included Allen key.
8. Remove the vinyl film from the dome cover once installation is complete.
#LX400043; r. 1.0/19290/23171; en-US
13
Controlling the PT Camera
with an NVR
7
The camera can accept Pan-Tilt commands directly through the Ethernet cable. There is no need to run special wiring to control the movement of the
camera.
NOTE
• The following instructions are based on the Lorex LNR400 Series NVR. See your
NVR’s instruction manual for instructions on controlling the PT camera with your
system.
• For the latest list of compatible NVRs, please visit www.lorextechnology.com/support.
To connect the camera to the system:
1. Connect the camera to your NVR as detailed in 5 Connecting the Camera,
page 5.
2. Right-click and click Main Menu. Enter the system user name (default:
admin) and password (default: 000000) if prompted.
3. Click
>Setting>Pan/Tilt/Zoom.
4. Under Channel, select the channel the micro PT camera is connected to.
5. Under PTZ Type, select Remote.
6. Click OK. You can now control your micro PTcamera using the system.
#LX400043; r. 1.0/19290/23171; en-US
14
Controlling the PT Camera with an NVR
7
7.1 Controlling the Camera’s Pan-Tilt Movement (Local NVR)
1. In Live View, double-click the channel that has the camera connected to
open in full-screen.
2. Right-click and click PTZ. Enter the system user name and password if
prompted. The PTZ menu opens.
3. Use the on-screen controls to control the camera.
Pan-Tilt Controls
1. Direction keys: Click to pan and tilt the camera. Click SIT to stop the current action.
2. Mouse PT: Click to activate mouse Pan-Tilt mode. In mouse Pan-Tilt
mode:
• Click and drag to move the camera.
• Use the scroll wheel to zoom in and out.
• Right-click to exit and return to normal Pan-Tilt controls.
3. Zoom/Focus/Iris: Click + / - next to Zoom to adjust the digital zoom level
(up to 3x digital zoom). Focus and iris settings are not supported.
4. Advanced controls: Click to open advanced Pan-Tilt controls.
5. Not supported.
7.2 Advanced Pan-Tilt Controls
Advanced Pan-Tilt controls can be used to save camera positions and cycle
through various positions, and automate camera actions.
To open advanced Pan-Tilt controls:
• Click the arrow in the Pan-Tilt control window to open advanced controls.
#LX400043; r. 1.0/19290/23171; en-US
15
Controlling the PT Camera with an NVR
7
Advanced Pan-Tilt controls overview:
1. No.: Select the number of the action you want to perform.
2. Not supported.
3. Not supported.
4. Preset: Click to call the selected preset.
5. Not supported.
6. Not supported.
7. Not supported.
8. Not supported.
9. Not supported.
10. Not supported.
11. Aux: Click to open the aux menu, where you can set up Presets.
7.2.1 Presets
Presets will save a camera position for quick retrieval.
To add presets:
1. Click
to open the aux menu.
#LX400043; r. 1.0/19290/23171; en-US
16
Controlling the PT Camera with an NVR
7
2. Click the Preset tab.
3. Enter the number of the preset you want to create under Preset.
4. Move the camera to the desired position and click Set.
To go to a preset:
• Under No., select the number of the preset you would like to go to and click
.
7.2.2 Tour (Not Supported)
7.2.3 Pattern (Not Supported)
7.2.4 Border (Not Supported)
#LX400043; r. 1.0/19290/23171; en-US
17
Technical Specifications
8
Image Sensor 1/3" 2.1MP
Video Format
NTSC / PAL
Effective Pixels 1920 (H) x 1080 (V)
Resolution Up to 1080p
Range ±180° Pan; 90° Tilt
Pan/Tilt Speed Max 100° / Sec (Preset)
Zoom 3x Digital Zoom
Min. Illumination 0.1 Lux in Black and White
Lens / Lens Type 3.6mm F1.2 / Fixed
Field of View (Horizontal)
90°
Scan System Progressive
Synchronization Internal
Iris AES
S / N Ratio >50dB (AGC Off)
Termination RJ45 10 / 100M Ethernet
Power Requirement
PoE (Power over Ethernet, Class 3)
1
; 12V DC
Power Consumption
Max. 220mA
Operating Temperature Range -4°F ~ 140°F / -20°C ~ 60°C
Operating Humidity Range Within 90%RH
Indoor/Outdoor Both (IP66)
2
Weight 0.25kg / 0.55lbs
#LX400043; r. 1.0/19290/23171; en-US
18
1. Compatible with Lorex LNR100 & LNR400 Series only.
2. Not intended for submersion in water. Installation in a sheltered location recommended.
Technical Specifications
8
8.1 Dimensions
#LX400043; r. 1.0/19290/23171; en-US
19
Troubleshooting
9
There is no picture at night.
• Camera is capable of seeing in extremely low light conditions (0.1 Lux), but
it cannot see in total darkness. It is recommended to install the camera
where there is some ambient light (e.g. street lighting, starlight, moonlight,
etc.) or leave a light on in the area where the camera is installed.
No image at startup.
• The camera may take up to 1 minute to power up after being connected to
the NVR. Wait 2 minutes before following steps below.
• Check to ensure your camera is properly connected (see 5 Connecting the
Camera, page 5).
• Ensure the camera is connected to a router on the same network as the
NVR.
• If the camera is connected to the LAN, you must search your network for
cameras using the NVR. See your NVR’s instruction manual for details.
• Make sure that the cable run is within the limitations specified in 5 Connect-
ing the Camera, page 5. All Ethernet cables must be rated CAT5e or higher.
• If using the power adapter, connect the power adapter to a different outlet.
• Ethernet cable may be damaged or not connected properly. Check your ca-
ble run or try a different cable.
• Reset the camera to factory default settings. See 10 Resetting the Camera,
page 22 for details.
No image or camera image is unclear.
• Dome cover is dirty. Clean the dome cover with a soft, slightly damp cloth.
Do not use anything other than water to clean the dome cover, as chemicals such as acetone can permanently damage the plastic.
Image is distorted.
• Digital zoom is activated. Activating digital zoom may reduce the resolution
of the camera image. Zoom out completely to return to the camera’s optimal resolution. See 7.1 Controlling the Camera’s Pan-Tilt Movement (Local
NVR), page 15 for instructions on using the zoom controls.
• Image may become unclear when camera is tilted too close to the camera
base (e.g. pointed parallel to the ceiling). Tilt the camera using the NVR or
in the FLIR Cloud™ Client software or mobile app.
Image is too bright.
#LX400043; r. 1.0/19290/23171; en-US
20
Troubleshooting
9
• Ensure your camera isn’t pointed directly at a source of light (e.g. sun or
spot light).
• Check your NVR’s brightness and contrast settings.
• Move your camera to a different location.
Image is too dark.
• Check your NVR’s brightness and contrast settings.
• Move your camera to a different location.
NVR motion detection is constantly triggering.
• Turn off motion detection on the channel the micro PT camera is connected
to. NVRs use video motion detection, which means they detect motion by
looking for changes between frames (images) in the video. If the camera is
moving, the NVR will detect this as motion.
#LX400043; r. 1.0/19290/23171; en-US
21
Resetting the Camera
10
The camera features a hard reset button that is used to reset all camera settings back to their default values. This is useful in case you’ve forgotten your
login information or to revert camera image settings back to their default
values.
To reset the camera:
1. Separate the camera from the mounting plate if needed and disconnect
camera cables.
2. Remove the 2 screws from the compartment cover on the camera base
using a Phillips screwdriver (not included).
#LX400043; r. 1.0/19290/23171; en-US
22
Resetting the Camera
10
3. Press and hold the reset button for 4 seconds.
4. Replace the compartment cover on the camera base.
#LX400043; r. 1.0/19290/23171; en-US
23
Notices
11
This product has been certified and found to comply with the limits regulated
by FCC, EMC, and LVD. Therefore, it is designated to provide reasonable protection against interference and will not cause interference with other appliance usage. However, it is imperative that the user follows the guidelines in
this manual to avoid improper usage, which may result in damage to the product, electrical shock and fire hazard injury.
11.1 FCC/IC Notice
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception (which can be determined by turning the equipment on and
off), the user is encouraged to try to correct the interference by one or more of
the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
4. Consult the dealer or an experienced radio or television technician for
assistance.
11.2 Modification
Any changes or modifications not expressly approved by the grantee of this
device could void the user's authority to operate the device.
Toute modification non approuvée explicitement par le fournisseur de licence
de l'appareil peut entraîner l'annulation du droit de l'utilsateur à utiliser
l'appareil.
11.3 ROHS
This product is fully compliant with the European Union Restriction of the Use
of Certain Hazardous Substances in Electrical and Electronic Equipment
("RoHS") Directive (2002/95/EC). The RoHS directive prohibits the sale of
#LX400043; r. 1.0/19290/23171; en-US
24
Loading...