Lorex LNR100 SERIES, LNR140 Series, LNR180 Series Instruction Manual
Instruction Manual
LNR100 SERIES
Instruction Manual
LNR100 SERIES
#; r. 1.0/14396/14396; en-US
iii
Thank you for purchasing this product. Lorex is committed to providing our customers with a high quality,
reliable security solution.
This manual refers to the following models:
LNR140 Series (4–Channel)
LNR180 Series (8–Channel)
For the latest online manual, downloads and product updates, and to learn about our complete line of
accessory products, please visit our website at:
www.lorextechnology.com
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO REDUCE THE RICK OF ELECTRIC SHOCK DO NOT REMOVE
COVER. NO USER SERVICABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying
the appliance.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT
TO RAIN OR MOISTURE.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF THE PLUG
TO THE WIDE SLOT AND FULLY INSERT.
#; r. 1.0/14396/14396; en-US
iv
Table of contents
1 Important Safeguards ....................... ............ ........................ ............ ...1
1.1 General Precautions ....... ............ ..... ............ ....... ................. ........1
1.2 Installation....................... ............ ................. ................... ..........1
1.3 Service ................. ................... ..... ............ ............ ............ ........3
1.4 Use....... ............ ........................ ............ ............ ............ ........... 3
2 LNR100 Series Features ............ ............ ............ ............ ............ ...........4
3 LNR100 Series Getting Started...................... ............ ............ ............ ....5
4 LNR100 Series Front Panel .. ............ ................. ....... ............ ..... ............ 6
5 LNR100 Series Rear Panel . ..... ............ ....... ............ ..... ............ .............. 7
6 Basic Setup (LNR100 Series) .... ................. ............ ....... ..... ............ ....... 8
6.1 Step 1: Connect the IP Cameras ......... ............ ............ ............ ....... 8
6.2 Step 2: Connect the Mouse................. ..... ............ ............ ............ .8
6.3 Step 3: Connect the Ethernet Cable .. ............ ............ ............ ..........8
6.4 Step 4: Connect the Monitor..... ................. ................... ..... ............ 9
6.5 Step 5: Connect the Power Adapter to Power the Cameras ....... ........... 9
6.6 Step 6: Connect the Power Adapter to Power the NVR .. ............ ........ 10
6.7 Step 6: Upgrade Firmware to Latest Version (if Available) ......... ......... 11
6.8 Step 7: Verify Camera Image .... ................. ................... ..... .......... 11
6.9 Step 8: Set the Time .. ............ ............ ..... ................... ............ .... 11
6.10 Default System Password & Port Numbers .. ............ ............ ........... 11
6.10.1 FLIR Cloud™ . ............ ........................ ............ ............... 11
6.11 Quick Access to System Information . ............ ............ ............ ........ 12
6.12 Connecting Cameras to the Local Area Network (LAN) .... ............ ..... 13
7 Mouse Control ...... ............ ............ ............ ..... ................... ............ .... 16
8 Using the System . ............ ..... ............ ................... ..... ............ ............17
8.1 On-Screen Display .............. ..... ............ ........................ ............ . 17
8.2 Using the Quick Menu........ ............ ............ ............ ............ ........ 18
8.3 Using Sequence Mode.... ............ ............ ............ ....................... 18
8.4 Adjusting Color Settings ........... ............ ............ ............ ............ .. 18
8.5 Using the Navigation Bar .. ........................ ............ ..... ............ ..... 19
8.6 Using the Camera Toolbar .. ............ ....... ................. ............ ........ 19
8.6.1 Using Quick Playback ...... ............ ............ ....................... 20
8.6.2 Using Digital Zoom in Live Display ....... ............ ............ ...... 20
8.6.3 Using Real-time Backup ...... ........................ ............ ........ 20
8.7 Using the Virtual Keyboard...... ............ ............ ............ ............ .... 21
8.8 Adjusting Camera Zoom & Focus . ............ ............ ............ ............ 21
9 Setting The Time ........... ............ ............ ............ ............ ............ ........ 23
9.1 Configuring Daylight Savings Time .. ................... ................. ......... 23
9.2 Configuring NTP ......... ........................ ............ ........................ .. 24
10 Recording.. ................. ................... ................. ................... ..... .......... 26
10.1 Video Recording Types ........... ........................ ............ ..... .......... 26
10.2 Main Stream and Sub Stream..... ............ ................. ................... . 26
10.3 Setting up Scheduled or Manual Recording ......... ............ ............ ... 26
10.4 Configuring Hard Drive Overwrite ......... ............ ............ ............ .... 27
11 Search (Playback) ...... ............ ............ ............ ............ ............ ........... 28
11.1 Playing Back Video from the Hard Drive. ..... ............ ............ ........... 28
11.2 Playback Controls .. ............ ............ ............ ............ ............ ....... 29
11.3 Playing Back from a USB Drive . ................. ................... ..... .......... 29
#; r. 1.0/14396/14396; en-US
v
Table of contents
12 Backup......... ............ ............ ............ ........................ ............ ............ 31
12.1 Formatting the USB Device .... ............ ............ ............ ............ ..... 31
12.2 Backing up Video........... ............ ............ ............ ....................... 31
12.3 Using Video Clip Backup .. ........................ ............ ............ .......... 33
12.4 Viewing Backup Files.......... ............ ............ ............ ................... 33
13 Managing Passwords and User Accounts..... ..... ............ ....... ............ .... 37
13.1 Changing Passwords... ............ ............ ............ ............ ............ .. 37
13.2 Adding Users .... ............ ............ ............ ............ ................. ...... 37
13.3 Modifying Users ...... ..... ............ ............ ............ ............ ............ 39
13.4 Deleting Users .... ................. ................... ................. ................ 39
13.5 Account Groups ...... ..... ............ ................... ..... ............ ............ 39
13.6 Adding Groups ..................... ............ ............ ............ ............ .... 39
13.7 Modifying Groups ........... ............ ............ ............ ..... ................. 40
13.8 Deleting Groups ......... ............ ............ ............ ............ ............ .. 40
14 Using the Main Menu .. ............ ............ ..... ....... ............ ................. ...... 41
14.1 Setting....... ................... ................. ................... ..... ............ ..... 42
14.1.1 Configuring General System Settings ........... ..... ................. 42
14.1.2 Configuring Holidays... ............ ............ ............ ............ .... 43
14.1.3 Configuring Recording Quality .... ............ ............ ............ .. 44
14.1.4 Configuring Privacy Zones ............ ............ ............ ........... 45
14.1.5 Configuring the Recording Schedule .... ........................ ...... 47
14.1.6 Configuring Pre-Recording ................ ................... ............ 48
14.1.7 Configuring Motion Detection Events .... ............ ............ ...... 48
14.1.8 Configuring Display Settings .................. ............ ..... .......... 50
14.1.9 Creating Custom Channel Names ....... ............ ............ ....... 51
14.2 Advanced.......... ............ ............ ............ ............ ............ .......... 53
14.2.1 Viewing Online Users ..... ....... ............ ................. ............. 53
14.2.2 Resetting the System to Default Settings .. ............ ..... .......... 53
14.2.3 Formatting Hard Drives........ ........................ ............ ........ 54
14.2.4 Selecting Hard Drive Types ....... ............ ............ ............ ... 54
14.2.5 Configuring System Warnings ...... ........................ ............ . 55
14.2.6 Saving Your System Configuration to a USB Flash
Drive........ ............ ............ ............ ............ ............ ........56
14.3 Network.......... ............ ............ ............ ............ ............ ............ 56
14.3.1 Configuring DHCP or Fixed IP Address ................... ............ 56
14.3.2 Configuring System Ports...................... ............ ..... .......... 57
14.3.3 Configuring DDNS.......... ........................ ............ ............ 58
14.3.4 Configuring Email Alerts .. ................... ..... ............ ............ 59
14.3.5 Configuring Switch Settings (Advanced)... ............ ..... .......... 62
14.4 Info ................... ................. ................... ................. ............ .... 64
14.4.1 HDD Info ....... ............ ............ ............ ............ ............ ... 64
14.4.2 BPS ........... ............ ............ ............ ............ ............ ..... 64
14.4.3 Log ..................... ............ ................. ................... ........ 64
14.4.4 Version ......... ............ ............ ............ ............ ............ ... 65
14.4.5 Remote Device Info .. ............ ............ ............ ............ ...... 66
14.4.6 Network Info........... ........................ ............ ................... 66
14.5 Shutdown....... ................. ....... ............ ................. ................... . 68
15 Connecting to Your System Over the Internet on PC or Mac .... ............ .... 69
15.1 System Requirements...... ........................ ............ ..... ................. 69
15.2 Step 1 of 3: Connect your System to Your Router ........... ............ ...... 69
#; r. 1.0/14396/14396; en-US
vi
Table of contents
15.3 Step 2 of 3: Obtain the system’s Device ID......... ............ ............ ..... 70
15.4 Step 3 of 3: Connect to the System Over the Internet . ............ ........... 70
16 Using FLIR Cloud™ Client for PC or Mac ....... ............ ............ ............ ... 74
16.1 Home Page ........... ............ ..... ....... ............ ................. ............. 74
16.2 Live View ........... ............ ............ ............ ........................ ......... 74
16.2.1 Live View Controls ............ ............ ............ ............ .......... 75
16.2.2 Opening Live View in Multiple Monitors ....... ............ ............ 76
16.2.3 Controlling PTZ Cameras. ............ ............ ............ ............ 77
16.3 Playback. ............ ............ ............ ............ ............ ............ ........ 78
16.4 Playback Controls .. ............ ............ ............ ............ ............ ....... 80
16.5 Downloading Video to your Computer Hard Drive...... ............ ........... 81
16.6 Alarm ...... ..... ............ ........................ ............ ............ ............ .. 82
16.7 Log.......... ............ ............ ............ ............ ............ ............ ...... 82
16.8 E-map ........... ............ ............ ............ ............ ............ ............ . 83
16.9 Devices .. ........................ ............ ................. ................... ........ 85
16.10 Device Config ....... ............ ............ ............ ............ ............ ....... 86
16.11 Alarm CFG .. ................. ................... ..... ............ ............ ........... 87
16.12 Tour & Task . ............ ............ ............ ............ ............ ............ .... 90
16.13 Account .. ............ ............ ............ ............ ............ ............ ........ 91
16.13.1 Managing User Accounts ............ ............ ............ ............ . 91
16.13.2 Managing Roles... ................. ................... ..... ............ ..... 93
16.14 General ................ ................... ..... ............ ........................ ...... 94
16.14.1 Basic ...... ........................ ............ ................. ................ 94
16.14.2 File .............. ............ ........................ ............ ............ ... 94
16.14.3 Alarm Prompt ......... ................. ............ ........................ .. 95
16.14.4 Version ............. ............ ..... ................... ................. ...... 96
17 Mobile Apps: Connecting to your System Using a Smartphone or
Tablet .... ............ ....... ..... ............ ............ ............ ............ ............ ....... 97
17.1 iPhone......... ............ ............ ............ ............ ............ ............ ... 97
17.1.1 Prerequisites.... ............ ............ ............ ............ ............ . 97
17.1.2 Connecting to your System on iPhone.... ............ ............ ..... 97
17.1.3 Live View Interface ......... ............ ............ ............ ............ 98
17.1.4 Controlling PTZ Cameras. ............ ............ ............ ............ 99
17.1.5 Viewing Snapshots and Videos with Local Files .................. 100
17.1.6 Using Playback Mode on iPhone ............. ................. ....... 101
17.1.7 Enabling Push Notifications ........... ............ ..................... 102
17.1.8 Using the Event List ...... ............ ............ ............ ............ 104
17.1.9 Using Favorites. ............ ............ ............ ............ ........... 105
17.1.10 Using the E-Map ............. ..... ............ ............ ............ .... 106
17.1.11 Device Manager......... ............ ............ ............ ............ .. 108
17.1.12 Adding Devices Using an IP or DDNS Address
(Advanced) ........... ........................ ............ ............ ...... 109
17.2 iPad ............ ............ ............ ............ ............ ............ ............ . 111
17.2.1 Prerequisites.... ............ ............ ............ ............ ........... 111
17.2.2 Connecting to your system on an iPad .... ............ ............ .. 111
17.2.3 Live View Interface ......... ............ ............ ............ .......... 112
17.2.4 Controlling PTZ Cameras. ............ ............ ............ .......... 113
17.2.5 Using Playback Mode on iPad..... ............ ............ ............ 114
17.2.6 Using Local File to View Manual Recordings ......... ..... ........ 116
17.2.7 Enabling Push Notifications ........... ............ ..................... 117
17.2.8 Using the Event List ...... ............ ............ ............ ............ 119
#; r. 1.0/14396/14396; en-US
vii
Table of contents
17.2.9 Using Favorites. ............ ............ ............ ............ ........... 120
17.2.10 Using the E-Map ............. ..... ............ ............ ............ .... 121
17.2.11 Using the Device Manager ...... ............ ............ ............ ... 123
17.2.12 Adding Devices Using an IP or DDNS Address
(Advanced) ........... ........................ ............ ............ ...... 123
17.3 Android ......... ............ ............ ............ ............ ............ ........... 126
17.3.1 Prerequisites.... ............ ............ ............ ............ ........... 126
17.3.2 Connecting to your System on Android .... ............ ............ . 126
17.3.3 Live View Interface ......... ............ ............ ............ .......... 127
17.3.4 Controlling PTZ Cameras. ............ ............ ............ .......... 128
17.3.5 Viewing Snapshots and Videos with Local Files .................. 129
17.3.6 Using Playback Mode on Android .. ............ ............ .......... 130
17.3.7 Enabling Push Notifications ........... ............ ..................... 131
17.3.8 Using the Event List ...... ............ ............ ............ ............ 133
17.3.9 Using Favorites. ............ ............ ............ ............ ........... 133
17.3.10 Using the E-Map ............. ..... ............ ............ ............ .... 135
17.3.11 Device Manager......... ............ ............ ............ ............ .. 137
17.3.12 Adding Devices Using an IP or DDNS Address
(Advanced) ........... ........................ ............ ............ ...... 138
18 LNR100 Series Hard Drive Installation.. ............ ....... ..... ............ .......... 140
18.1 Installing a Hard Drive ............ ............ ............ ............ ............ .. 140
18.2 Removing the Hard Drive........... ............ ............ ............ ........... 142
18.3 Formatting Hard Drives ....... ............ ............ ............ ............ ..... 144
19 DDNS Setup (Advanced) ........... ............ ............ ............ ............ ....... 145
19.1 Accessing your System within a Local Network (LAN) .. ............ ....... 145
19.1.1 Step 1 of 3: Connect your System to Your Router .. .............. 145
19.1.2 Step 2 of 3: Obtain the System’s Local IP Address ......... ...... 146
19.1.3 Step 3 of 3: Connect to the System’s Local IP
Address........... ............ ........................ ............ ..... ...... 146
19.2 DDNS Setup—Access your System Remotely over the
Internet ........... ............ ............ ............ ............ ...................... 148
19.2.1 Step 1 of 4: Port Forwarding .. ............ ............ ............ ..... 149
19.2.2 Step 2 of 4: Create a DDNS Account .................. ............ .. 149
19.2.3 Step 3 of 4: Enable DDNS on the System .... ............ .......... 153
19.2.4 Step 4 of 4: Connect to the System’s DDNS Address ........... 154
20 Connecting a PTZ Camera (LNR100 Series) ........... ............ ................. 158
20.1 Controlling a PTZ Camera (Local NVR) ....... ............ ..... ............ ... 158
20.2 PTZ Actions. ........................ ............ ............ ............ ............ .. 158
20.2.1 Presets ....... ........................ ............ ............ ............ ... 159
20.2.2 Tours ....... ............ ............ ............ ............ ............ ...... 160
20.2.3 Pattern ..................... ............ ............ ............ ............ .. 161
20.2.4 Auto Scan ....... ............ ............ ............ ............ ........... 162
20.3 Controlling the Camera’s Menu .... ........................ ............ .......... 163
21 LNR100 Series Troubleshooting ........... ............ ............ ..................... 165
22 LNR100 Series System Specifications...... ............ ............ ............ ...... 167
22.1 System ............ ............ ............ ............ ............ ..................... 167
22.2 Inputs/Outputs ..................... ............ ..... ................... ............ .. 167
22.3 Display ........... ..... ............ ............ ............ ............ ............ ..... 167
22.4 Recording ....... ............ ............ ........................ ............ .......... 167
22.5 Playback and Backup .. ........................ ............ ........................ 168
22.6 Storage & Archive .. ............ ............ ............ ............ ............ ..... 168
#; r. 1.0/14396/14396; en-US
viii
Table of contents
22.7 Connectivity....... ............ ............ ............ ............ ............ ........ 168
22.8 General ................ ................... ..... ............ ........................ .... 168
22.9 Recording Resolution (Pixels) & Speed (FPS — Frames per
second)......... ............ ............ ............ ............ ............ ............ 169
23 Notices....... ....... ..... ............ ............ ............ ............ ............ ............ 170
23.1 FCC/IC Notice........ ............ ..... ....... ............ ................. ........... 170
23.2 Modification........ ........................ ............ ........................ ....... 170
23.3 ROHS .............. ............ ............ ............ ............ ............ ........ 170
#; r. 1.0/14396/14396; en-US
ix
1
Important Safeguards
In addition to the careful attention devoted to quality standards in the manufacturing process of your product, safety is a major factor in the design of every instrument. However,
safety is your responsibility too. This sheet lists important information that will help to ensure your enjoyment and proper use of the product and accessory equipment. Please read
them carefully before operating and using your product.
1.1 General Precautions
1. All warnings and instructions in this manual should be followed.
2. Remove the plug from the outlet before cleaning. Do not use liquid aerosol detergents.
Use a water-dampened cloth for cleaning.
3. Do not use this product in humid or wet places.
4. Keep enough space around the product for ventilation. Slots and openings in the storage cabinet should not be blocked.
5. It is highly recommended to connect the product to a surge protector to protect from
damage caused by electrical surges. It is also recommended to connect the product to
an uninterruptible power supply (UPS), which has an internal battery that will keep the
product running in the event of a power outage.
CAUTION
Maintain electrical safety. Power line operated equipment or accessories connected to this product
should bear the UL listing mark or CSA certification mark on the accessory itself and should not be modified so as to defeat the safety features. This will help avoid any potential hazard from electrical shock or
fire. If in doubt, contact qualified service personnel.
1.2 Installation
1. Read and Follow Instructions - All the safety and operating instructions should be
read before the product is operated. Follow all operating instructions.
2. Retain Instructions - The safety and operating instructions should be retained for future reference.
3. Heed Warnings - Comply with all warnings on the product and in the operating
instructions.
4. Polarization - Do not defeat the safety purpose of the polarized or grounding-type
plug.
A polarized plug has two blades with one wider than the other.
A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety.
If the provided plug does not fit into your outlet, consult an electrician for replacement
of the obsolete outlet.
#; r. 1.0/14396/14396; en-US
1
1
Important Safeguards
5. Power Sources - This product should be operated only from the type of power source
indicated on the marking label. If you are not sure of the type of power supplied to your
location, consult your video dealer or local power company. For products intended to
operate from battery power, or other sources, refer to the operating instructions.
6. Overloading - Do not overload wall outlets or extension cords as this can result in the
risk of fire or electric shock. Overloaded AC outlets, extension cords, frayed power
cords, damaged or cracked wire insulation, and broken plugs are dangerous. They
may result in a shock or fire hazard. Periodically examine the cord, and if its appearance indicates damage or deteriorated insulation, have it replaced by your service
technician.
7. Power-Cord Protection - Power supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or against them. Pay particular
attention to cords at plugs, convenience receptacles, and the point where they exit
from the product.
8. Surge Protectors - It is highly recommended that the product be connected to a
surge protector. Doing so will protect the product from damage caused by power
surges. Surge protectors should bear the UL listing mark or CSA certification mark.
9. Uninterruptible Power Supplies (UPS) - Because this product is designed for continuous, 24/7 operation, it is recommended that you connect the product to an uninterruptible power supply. An uninterruptible power supply has an internal battery that will
keep the product running in the event of a power outage. Uninterruptible power supplies should bear the UL listing mark or CSA certification mark.
10. Ventilation - Slots and openings in the case are provided for ventilation to ensure reliable operation of the product and to protect it from overheating. These openings must
not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should never be placed
near or over a radiator or heat register. This product should not be placed in a built-in
installation such as a bookcase or rack unless proper ventilation is provided and the
product manufacturer’s instructions have been followed.
11. Attachments - Do not use attachments unless recommended by the product manufacturer as they may cause a hazard.
12. Water and Moisture - Do not use this product near water — for example, near a bath
tub, wash bowl, kitchen sink or laundry tub, in a wet basement, near a swimming pool
and the like.
13. Heat - The product should be situated away from heat sources such as radiators, heat
registers, stoves, or other products (including amplifiers) that produce heat.
14. Accessories - Do not place this product on an unstable cart, stand, tripod, or table.
The product may fall, causing serious damage to the product. Use this product only
with a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold
with the product. Any mounting of the product should follow the manufacturer’s instructions and use a mounting accessory recommended by the manufacturer.
15. Camera Extension Cables – Check the rating of your extension cable(s) to verify
compliance with your local authority regulations prior to installation.
16. Mounting - The cameras provided with this system should be mounted only as instructed in this guide or the instructions that came with your cameras, using the provided mounting brackets.
#; r. 1.0/14396/14396; en-US
2
1
Important Safeguards
17. Camera Installation - Cameras are not intended for submersion in water. Not all cameras can be installed outdoors. Check your camera environmental rating to confirm if
they can be installed outdoors. When installing cameras outdoors, installation in a
sheltered area is required.
1.3 Service
1. Servicing - Do not attempt to service this product yourself, as opening or removing
covers may expose you to dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
2. Conditions Requiring Service - Unplug this product from the wall outlet and refer
servicing to qualified service personnel under the following conditions:
• When the power supply cord or plug is damaged.
• If liquid has been spilled or objects have fallen into the product.
• If the product has been exposed to rain or water.
• If the product has been dropped or the cabinet has been damaged
• If the product does not operate normally by following the operating instructions. Ad-
just only those controls that are covered by the operating instructions. Improper adjustment of other controls may result in damage and will often require extensive
work by a qualified technician to restore the product to its normal operation.
• When the product exhibits a distinct change in performance. This indicates a need
for service.
3. Replacement Parts - When replacement parts are required, have the service technician verify that the replacements used have the same safety characteristics as the original parts. Use of replacements specified by the product manufacturer can prevent fire,
electric shock, or other hazards.
4. Safety Check - Upon completion of any service or repairs to this product, ask the
service technician to perform safety checks recommended by the manufacturer to determine that the product is in safe operating condition.
1.4 Use
1. Cleaning - Unplug the product from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp cloth for cleaning.
2. Product and Cart Combination - When product is installed on a cart, product and
cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.
3. Object and Liquid Entry - Never push objects of any kind into this product through
openings as they may touch dangerous voltage points or “short-out” parts that could
result in a fire or electric shock. Never spill liquid of any kind on the product.
4. Lightning - For added protection of this product during a lightning storm, or when it is
left unattended and unused for long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent damage to the product due
to lightning and power line surges.
#; r. 1.0/14396/14396; en-US
3
2
LNR100 Series Features
Features
• High definition 1080p Recording Real-time recording at 30fps per channel
• 4 Built in PoE (Power Over Ethernet) ports providing video and power on a single Ether-
net cable Automatically detects compatible IP cameras in the network
• Expand your system with a network PoE switch, sold separately
4
• 24/7 security-grade hard drive
.
3
.
• Continuous, scheduled and motion recording.
• Simultaneous playback and live view on the same screen.
• Selectable area digital zoom in live view and playback.
• Accurate time stamps with NTP & daylight savings time.
• H.264 video compression
4
.
• Instant USB backup of live video from selected camera
• 2 video outputs (HDMI & VGA) to connect multiple monitors.
• HDMI cable included for simple connection to HD TVs.
• Keep up to date with automatic firmware upgrades
6
• 3-Step remote view with FLIR Cloud™
.
5
.
• PC and Mac compatible.
• Free iOS and Android compatible apps with live viewing, playback, video recording,
and snap shot.
• Dedicated iPad app with multi-channel live viewing and playback.
• Push notifications of motion events.
• Instant email alerts with snap shot attachment.
• Dual streaming to conserve bandwidth.
1
.
2
.
Note
1. Real time recording on 4 Channels at 1080p (1920x1080), 8 channels at 720p (1280x720).
2. Compatible with Lorex 1080p wired PoE HD cameras only. For a list of compatible cameras, please
visit www.lorextechnology.com/support .
3. NVR includes 4 built in PoE ports. Up to 4 cameras can be added to 8–channel models with the addition of a PoE switch (sold separately, www.lorextechnology.com).
4. Recording time may vary based on recording resolution & quality, lighting conditions and movement
in the scene.
5. The NVR firmware and software must be upgraded to the latest version to use the FLIR Cloud™service. When the system is connected to the Internet, it will automatically alert you if there is a firmware
upgrade available.
6. Requires a high speed internet connection and a router (not included). A minimum upload speed of
1Mbps is required for the best video performance. Up to 3 devices may connect to the system at the
same time. For the latest list of supported apps and devices, please visit
www.lorextechnology.com/support.
Use product in accordance with the instructions provided. All trademarks belong to their respective owners. No claim is made to the exclusive right to use the trademarks listed, other than the trademarks
owned by Lorex Corporation. We reserve the right to change models, configurations or specifications
without notice or liability. Product may not be exactly as shown. Images are simulated.
#; r. 1.0/14396/14396; en-US
4
3
LNR100 Series Getting Started
The system comes with the following components:
Network Video Recorder
Ethernet cable HDMI cable
Hard drive size, number of channels, and camera configuration may vary by model. Please
refer to your package for specific content details. Check your package to confirm that you
have received the complete system, including all components shown above.
Power adapter x 2
(1 x for PoE switch, 1 x for NVR)
Mouse
Quick start guides
#; r. 1.0/14396/14396; en-US
5
4
4
2
3
LNR100 Series Front Panel
1. NET: Glows when network is in normal state. Turns off for network error.
2. Power Indicator: Glows to indicate the system is on.
3. HDD: Glows to indicate hard drive is in normal state. Turns off when there is a hard
drive error.
4. USB Port: Connect a USB mouse (included) or connect a USB flash drive (not included) for data backup or firmware upgrades.
#; r. 1.0/14396/14396; en-US
6
5
7
4
2
3
5
6
LNR100 Series Rear Panel
1. DC 48V: Port for 48V DC power adapter (included) that supplies power to the cameras
connected to the PoE ports.
2. DC 12V: Port for 12V DC power adapter (included) that supplies power to the NVR.
3. PoE Ports: Camera input ports for IP cameras.
4. LAN: Connect an Ethernet cable to connect the system to your router (not included).
5. HDMI: HDMI port to connect the system to a HDMI TV/monitor.
6. USB port: Connect a USB mouse or connect a USB flash drive (not included) for data
backup or firmware upgrades.
7. VGA: VGA port to connect the system to a VGA monitor.
#; r. 1.0/14396/14396; en-US
7
6
Basic Setup (LNR100 Series)
6.1 Step 1: Connect the IP Cameras
Option 1: Direct Connection to NVR
• Connect cameras to the PoE ports on the rear panel of the NVR using Cat5e or higher
grade Ethernet cable. The cameras will appear on the NVR without any additional configuration when the system starts up.
Note
You must use Lorex IP cameras. Visit www.lorextechnology.com/support for a list of cameras compat-
ible with this system.
Connect IP cameras directly to PoE ports.
Option 2: Connect Cameras to Local Network
You can also connect your IP cameras to your local network for flexible installations. You
will need to do this to connect cameras 5~8 to 8–channel models. For details, see 6.12
Connecting Cameras to the Local Area Network (LAN), page 13.
6.2 Step 2: Connect the Mouse
• Connect a USB mouse (included) to one of the USB ports.
6.3 Step 3: Connect the Ethernet Cable
• Connect an Ethernet cable (included) to the LAN port on the rear panel of the DVR.
Connect the other end of the Ethernet cable to a router on your network.
#; r. 1.0/14396/14396; en-US
8
6
0
0
Basic Setup (LNR100 Series)
6.4 Step 4: Connect the Monitor
• Connect the included HDMI cable from the HDMI port to the TV or monitor
(recommended).
OR
• Connect a VGA cable (not included) from the VGA port to the monitor.
1. VGA port.
2. HDMI port.
6.5 Step 5: Connect the Power Adapter to Power the Cameras
The system includes two power adapters. You must connect both to use the system. There
is a 48V power adapter that provides power to the cameras via the built-in Power over
Ethernet (PoE) switch and a 12V power adapter to power the NVR.
To connect the power adapter that powers the cameras:
• Connect the included 48V power adapter to the DC 48V port. Connect the end of the
power adapter to a wall socket or a surge protector.
#; r. 1.0/14396/14396; en-US
9
6
Basic Setup (LNR100 Series)
6.6 Step 6: Connect the Power Adapter to Power the NVR
• Connect the included 12V power adapter to the DC 12V port. This will power on the
NVR.
At startup, the system performs a basic system check and runs an initial loading sequence.
After a few moments, the system loads a live display view.
#; r. 1.0/14396/14396; en-US
10
6
Basic Setup (LNR100 Series)
6.7 Step 6: Upgrade Firmware to Latest Version (if Available)
If a firmware upgrade is available, you will be asked to install it once the system starts up.
It is required to upgrade your system firmware and client software or mobile apps to the latest version to enable remote connection to the system.
If a firmware upgrade is available:
1. After startup, a notification will appear asking you to upgrade the firmware. Click OK to
upgrade.
2. Enter the system user name (default: admin) and password (default: 000000) and
click OK. Wait for the firmware update to complete. The system will restart once the
firmware has been upgraded.
WARNING
DO NOT POWER OFF THE SYSTEM OR DISCONNECT THE POWER CABLE DURING FIRMWARE INSTALLATION
6.8 Step 7: Verify Camera Image
• Power on the cameras, and then verify the camera video quality before mounting the
cameras to a permanent location.
• Mount the cameras under a sheltered location. Always verify the outdoor rating of your
camera before installing it in a permanent location.
6.9 Step 8: Set the Time
• Set the system time and date for accurate video time stamps. Videos with inaccurate
times may not be valid as surveillance evidence.
• For details on setting the system time, see 9 Setting The Time, page 23.
6.10 Default System Password & Port Numbers
CAUTION
By default, the system user name is admin and the password is 000000. It is essential that you create
your own password. For details, see 13 Managing Passwords and User Accounts, page 37.
The system requires a user name and password to log in to the system remotely using a
computer or mobile device. After logging on remotely the first time, you will be asked to
create a custom password for the system.
Local system and remote connectivity (LAN & Internet) user name and password:
• Username: admin
• Password: 000000
Default ports for DDNS remote access:
• Port 80 (HTTP port)
• Port 35000 (Client port)
6.10.1 FLIR Cloud™
This system features the exclusive FLIR Cloud™. This is a cloud service that allows you to
connect to your system over the Internet via a secure handshake with our servers. This
means you can easily connect to your system without requiring any network configuration.
#; r. 1.0/14396/14396; en-US
11
6
Basic Setup (LNR100 Series)
For details on setting up your system to connect to the Internet using FLIR
Cloud™:
• See 15 Connecting to Your System Over the Internet on PC or Mac, page 69.
OR
• See 17 Mobile Apps: Connecting to your System Using a Smartphone or Tablet, page
97.
Connectivity using Lorex’s free DDNS service is also available, but requires the ports listed
above to be port forwarded on your router.
6.11 Quick Access to System Information
To quickly open a window that displays vital system information:
• Right-click to open the Quick Menu and click Info. Enter the system user name (default:
admin) and password (default: 000000).
Note
The QR code shown in the System Info screen can be scanned during mobile setup to enter the system’s
Device ID.
#; r. 1.0/14396/14396; en-US
12
6
Router
IP Ca m e ra s
NVR
NTERNET
P
oE Switc h
witch
P C a m e ra s
Basic Setup (LNR100 Series)
6.12 Connecting Cameras to the Local Area Network (LAN)
For flexibility, you may also connect IP cameras to the same Local Area Network (LAN) as
the NVR. This is accomplished by connecting the cameras to the same router as the NVR.
For these installations, an external PoE switch (sold separately) or power adapter (sold
separately) must be used to provide power to each IP camera. You also must add the cameras on the NVR before they will show a picture on the monitor or be recorded by the NVR.
Follow the steps below to connect the cameras to the NVR over the LAN.
Note
You must use Lorex IP cameras. Visit www.lorextechnology.com/support for a list of cameras compatible
with this system.
Step 1 of 2 — Option A: Connecting cameras to your local network using a PoE
switch:
1. Connect an Ethernet cable from the LAN port on an external PoE switch (sold separately on www.lorextechnology.com) to your router using a CAT5e or higher Ethernet
cable. Connect the power cable to the PoE swtich and to a power outlet or surge
protector.
Note
Terminology may vary depending on the model of PoE switch you have.
2. Connect the IP cameras to the PoE switch using the Ethernet extension cables. The
PoE switch will provide power and video transmission the same way your NVR.
#; r. 1.0/14396/14396; en-US
13
6
Router
IP Ca m e ra s
NVR
NTERNET
P C a m e ra s
Po we r a d a p te r (n o t includ e d )
Basic Setup (LNR100 Series)
Step 1 of 2 — Option B: Connecting cameras to your local network using power
adapters:
1. Connect the cameras to a compatible power adapter (visit www.lorextechnology.com
for compatible power adapters for your cameras).
2. Connect the camera to your router using a CAT5e or higher Ethernet cable.
Step 2 of 2: Add the cameras to your NVR:
1. Right-click and select Device Search.
2. Log in using the admin account (default User Name: admin; default Password:
000000).
3. Click IP Search. The system searches the network for compatible cameras.
4. Check the camera(s) you would like to add.
#; r. 1.0/14396/14396; en-US
14
6
Basic Setup (LNR100 Series)
5. Click Add. The Status indicator turns green to show the camera is successfully
connected.
6. Click OK to save changes.
Note
You can also add a camera to a specific channel by hovering the mouse over an empty channel in split-
screen view and clicking
. Then double-click the camera you would like to add and right click to exit.
#; r. 1.0/14396/14396; en-US
15
7
2
3
Mouse Control
The mouse is the primary control device for the system. To connect a USB mouse:
• Connect a USB mouse to the USB port on the front or rear panel.
1. Left-button:
• In live view, click to open the Navigation Bar. Right-click to close the navigation bar.
• In live view, while in a split-screen display mode, double-click an individual channel
to view it in full-screen. Double-click again to return to the split-screen display mode.
• While navigating menus, click to open a menu option.
2. Right-button:
• During live view, right-click anywhere on the screen to open the Quick Menu.
• Within system menus, right-click to exit menus.
3. Scroll wheel: In live view, use the scroll wheel to zoom in/out.
#; r. 1.0/14396/14396; en-US
16
8
2
3
4
5
Using the System
Use the system’s graphical on-screen display to navigate menus and configure options
and settings.
8.1 On-Screen Display
The system shows the following for all display views:
1. Display area:
• Double-click on a channel to view in full-screen; double-click again to return to split
screen.
• Right-click to open the Quick Menu.
• Left-click to open the Navigation Bar.
• Move the mouse to the top of a channel to view the Camera Toolbar.
• Click-and-drag cameras to rearrange the channel display. This does not affect the
channels each camera is connected or recording to.
2. Channel name
3. C: Camera is continuously recording.
4. M: Motion has been detected.
5. Date & time: Current system date and time. For details on setting the date and time,
see 9 Setting The Time, page 23.
#; r. 1.0/14396/14396; en-US
17
8
Using the System
8.2 Using the Quick Menu
The Quick menu gives you access to the system’s key functions. To access the Quick
Menu, right-click the screen during live view.
The Quick Menu has the following options:
• View: Select a camera in full-screen or select a multi-channel display.
• Pan/Tilt/Zoom: Access controls for PTZ cameras (not included).
• AutoFocus: Access zoom/focus controls for auto-focus cameras (not included).
• Color Setting: Configure color settings for cameras.
• Search: Search/playback recorded video. See 11 Search (Playback), page 28.
• Record: Open the Record menu to select manual recording options. See 10.3 Setting
up Scheduled or Manual Recording, page 26.
• Device Search: Open the Device Search menu to manage IP cameras.
• Info: Opens the system information window.
• Sequence: Click to start/stop sequence mode. In sequence mode, the system will au-
tomatically cycle through connected cameras every few seconds.
• Main Menu: Open the Main Menu. See 14 Using the Main Menu, page 41.
8.3 Using Sequence Mode
In sequence mode, the system will automatically cycle through connected cameras every
few seconds.
To use sequence mode:
1. Right-click and select Sequence to start sequence mode. A
will appear to show
that sequence mode is on.
2. Click the icon to pause sequence mode on the channel that is currently shown (icon
changes to
). Click again to resume sequence mode.
3. Right-click and select Sequence to return to normal viewing mode.
8.4 Adjusting Color Settings
Use the Color Settings menu to adjust color settings for your cameras.
To adjust color settings:
1. Right-click on the channel you would like to configure and select Color Setting. Enter
the system password if prompted.
#; r. 1.0/14396/14396; en-US
18
8
2
4
5 6 7
8 9310
Using the System
2. Adjust the Hue, Brightness, Contrast, and Saturation settings that the camera will
use. To enable custom Gain controls, check Gain and use the slider to configure the
gain level.
OR
Use Color mode to select a preset color profile.
Note
• Color settings will update once you save changes.
• To configure the Customized1~4 profiles, click Customized.
3. Click OK to save changes.
8.5 Using the Navigation Bar
The Navigation Bar gives quick access to certain functions and menus.
To open the Navigation bar:
• Left click on the screen to open the Navigation Bar. The Navigation Bar has the follow-
ing options:
1. Main Menu.
2. Collapse.
3. Select display layout.
4. PTZ: Click to open PTZ controls.
5. Search: Search and playback recorded video. See 16.3 Playback, page 78.
6. Alarm Status: View alarms in progress.
7. Network: Configure network settings for your system. See 14.3 Network, page 56.
8. HDD Manager: Manage hard drives connected to the system. See 14.2.3 Formatting Hard Drives,
page 54.
9. Info: Click to view system info.
10. Update: Click to check for firmware upgrades. The system must be connected to the Internet to
check for firmware upgrades.
8.6 Using the Camera Toolbar
The Camera Toolbar is used to perform actions on a specific channel.
To access the Camera Toolbar:
• Move the mouse to the top of the channel display. The Camera Toolbar has the following options:
#; r. 1.0/14396/14396; en-US
19
8
5
1 2 3
Using the System
1. Quick Playback.
2. Digital Zoom.
3. Real-time backup.
4. Not supported.
5. Not supported.
8.6.1 Using Quick Playback
Quick Playback is used to playback the last 5~60 minutes of video from the selected channel. You can also access Quick Playback in split-screen mode, while still viewing live video
from the other channels.
To use Quick Playback:
1. Move your mouse to the top of the channel display and click
Note
By default, the system will begin playback from 5 minutes ago. You can increase this to up to 60 mi-
nutes using the Instant Playback setting in Main Menu>
.
>General.
2. Right-click to exit Quick Playback.
8.6.2 Using Digital Zoom in Live Display
1. Move your mouse to the top of the channel display and click
to activate digital
zoom. A check mark will appear in the icon to indicate digital zoom is activated.
Note
You may activate digital zoom in multiple channels at the same time.
2. Click and drag inside the channel to zoom in.
• Click and drag to pan the zoom area.
• Right-click to zoom out and select a new zoom area.
• Click
to disable digital zoom. Note that the channel will remain at the same
zoom level until you right-click inside it.
8.6.3 Using Real-time Backup
Real-time backup allows you to save footage from the live display to a USB flash drive (not
included) or external hard drive (not included).
To use Real-time Backup:
1. Insert the USB flash drive or external hard drive into one of the USB ports on the
system.
2. Move your mouse to the top of the channel display and click
Backup.
#; r. 1.0/14396/14396; en-US
to start Real-time
20
Loading...