Lorex LNR110 Series Instruction Manual
Instruction Manual
LNR110 Series
Instruction Manual
LNR110 Series
#LX400070; r. 1.0/27147/27147; en-US
iii
Thank you for purchasing this product. Lorex is committed to providing our customers with a high quality,
reliable security solution.
This manual refers to the following models:
LNR118 (8-channel)
For the latest online manual, downloads and product updates, and to learn about our complete line of
accessory products, please visit our website at:
www.lorextechnology.com
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE
COVER. NO USER SERVICABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying
the appliance.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT
TO RAIN OR MOISTURE.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF THE PLUG
TO THE WIDE SLOT AND FULLY INSERT.
#LX400070; r. 1.0/27147/27147; en-US
iv
Table of contents
1 Important Safeguards ........... ............ ............ ....... ........................ ........1
1.1 General Precautions ....... ............ ............ ............ ................... ..... .1
1.2 Installation........... ............ ............ ........................ ....... ............ ...1
1.3 Service ........................ ............ ............ ............ ....... ............ ......3
1.4 Use....... ................... ............ ............ ............ ....... ..................... 3
2 LNR110 Series Features ........................ ....... ............ ............ ............ ....4
3 Getting Started (LNR110 Series) . ............ ....... ........................ ............ ...6
4 Front Panel (LNR110 Series) ....... ............ ............ ............ ................... ...7
5 LNR110 Series Rear Panel . ............ ............ ............ ....... ..... ................... 8
6 Basic Setup (LNR110 Series) .... ............ ............ ............ ....... ..... ............9
6.1 Step 1: Connect the IP Cameras ......... ................... ..... ....... ............ 9
6.2 Step 2: Connect the Mouse..... ............ ............ ............ .................. 9
6.3 Step 3: Connect the Ethernet Cable .. ........................ ....... ............ . 10
6.4 Step 4: Connect the Monitor..... ............ ............ ............ ....... ........ 10
6.5 Step 5: Connect the Power Adapter to Power the NVR .. ............ ........ 10
6.6 Step 6: Upgrade Firmware to Latest Version (if Available) ......... ....... .. 11
6.7 Step 7: Verify Camera Image .... ............ ............ ................... ........ 11
6.8 Step 8: Set the Time .. ............ ............ ....... ........................ ......... 11
6.9 Default System Password & Port Numbers .. ................... ............ .... 11
6.9.1 FLIR Cloud™ . ................... ............ ............ ............ ........ 12
6.10 Quick Access to System Information . ....... ........................ ............ . 12
6.11 Connecting Cameras to the Local Area Network (LAN) ........... .......... 13
7 Mouse Control ...... ............ ............ ................... ............ ............ ......... 16
8 Using the System . ............ ............ ............ ................... ..... ....... .......... 17
8.1 On-Screen Display .. ............ ............ ............ ............ ............ ...... 17
8.2 Using the Quick Menu........ ................... ............ ............ ............ . 17
8.3 Adjusting Camera Image Settings........ ................... ..... ................. 18
8.4 Using the Navigation Bar .. ............ ............ ............ ....... ..... .......... 20
8.5 Using the Camera Toolbar .. ....... ............ ............ ............ ............. 20
8.5.1 Using Quick Playback ...... ............ ............ ....... ............ .... 21
8.5.2 Using Digital Zoom in Live Display .............. ............ ........... 21
8.5.3 Using Real-time Backup ...... ............ ............ ................... . 21
8.6 Using the Virtual Keyboard...... ............ ....... ........................ ......... 22
8.7 Adjusting Camera Zoom & Focus . ................... ..... ....... ............ ..... 22
8.8 Setting The Time ........... ....... ............ ............ ............ ............ .... 23
9 Recording.. ............ ............ ............ ........................ ....... ............ ........ 25
9.1 Video Recording Types ........... ............ ............ ................... ........ 25
9.2 Main Stream and Sub Stream..... ............ ........................ ....... ...... 25
9.3 Setting up Scheduled or Manual Recording ................ ............ ........ 25
9.4 Configuring Hard Drive Overwrite ......... ............................... ......... 26
10 Search (Playback) .................. ....... ............ ............ ............ ............ .... 28
10.1 Playing Back Video from the Hard Drive. ..... ....... ............ ............ .... 28
10.2 Playback Controls .. ............ ............................... ............ ............ 29
10.3 Playing Back from a USB Drive . ............ ............ ................... ........ 29
11 Backup......... ............ ....... ..... ................... ............ ............ ............ ..... 31
11.1 Formatting the USB Thumb Drive ...... ............ ................... ............ 31
11.2 Backing up Video........... ................... ..... ................... ............ .... 32
11.3 Using Video Clip Backup ......... ............ ............ ............ ............... 33
11.4 Viewing Backup Files.......... ........................ ....... ............ ............ 34
#LX400070; r. 1.0/27147/27147; en-US
v
Table of contents
11.4.1 Viewing Backup Files on PC ........... ....... ............ ............ ... 34
11.4.2 Viewing Backup Files on Mac ......... ............ ............ .......... 37
12 Managing Passwords and User Accounts..... ............ ............ ................ 40
12.1 Changing Passwords... ....... ........................ ............ ............ ....... 40
12.2 Adding Users .... ............ ............ ....... ..... ................... ............ .... 41
12.3 Modifying Users ...... ..... ....... ............ ............ ............ ............ ..... 41
12.4 Deleting Users .... ............ ............ ............ ....... ........................ .. 42
12.5 Account Groups ...... ..... ....... ............ ............ ............ ................. 42
12.6 Adding Groups .... ........................ ............ ............ ............ ......... 42
12.7 Modifying Groups ........... ........................ ................... ............ ... 43
12.8 Deleting Groups ......... ........................ ....... ............ ............ ....... 43
13 Using the Main Menu .. ............ ............ ....... ..... ................... ............ .... 44
13.1 Camera .... ............ ................... ..... ....... ............ ............ ....... .... 44
13.1.1 Remote Device ..................... ....... ............ ............ .......... 44
13.1.2 Viewing Camera Status ........... ..... ....... ............ ............ .... 45
13.1.3 Viewing Camera Firmware Versions ............. ..... ....... .......... 45
13.1.4 Upgrading Camera Firmware ....... ....... ........................ ...... 45
13.1.5 Recording.. ............ ............ ............ ................... ............ 46
13.1.6 Configuring Recording Quality .... ................... ............ ....... 46
13.1.7 Configuring Snapshot Recording Settings...... ............ .......... 47
13.1.8 Creating Custom Channel Names ....... ....... ............ ............ 48
13.2 Info ....... ............ ............ ............ ................... ........................ .. 50
13.2.1 HDD Info ....... ................... ........................ ............ ........ 50
13.2.2 Record Info ......... ............ ............ ................... ..... ....... ... 50
13.2.3 Version .. ....... ............ ............ ............ ............ ....... ........ 51
13.2.4 Event Info ...... ....... ............ ............ ............ ............ ....... . 51
13.2.5 Online Users .. ............ ....... ........................ ............ ........ 52
13.2.6 Load...... ................... ............ ............ ............ ............... 52
13.2.7 Test. ............ ............ ............ ....... ........................ ......... 53
13.2.8 BPS ........... ....... ........................ ............ ............ .......... 53
13.2.9 Log ......... ............ ............ ........................ ....... ............ . 53
13.3 Setting.............. ............ ............ ............ ................... ..... ....... ... 54
13.3.1 Network ......... ........................ ....... ............ ............ ....... 54
13.3.2 Selecting DHCP or Static IP Address (TCP/IP) .................. .... 54
13.3.3 Configuring System Ports (Connection)... ............ ............ .... 55
13.3.4 Configuring DDNS Settings .. ........................ ............ ........ 56
13.3.5 Configuring Email Alerts ......... ............ ............ ............ ..... 56
13.3.6 Configuring Switch Settings (Advanced)... ............ ............... 59
13.3.7 Event.............................. ............ ............ ............ ......... 59
13.3.8 Configuring Motion Detection.................... ............ ............ 59
13.3.9 Configuring Video Loss Settings .... ............ ............ ............ 61
13.3.10 Configuring Hard Drive Warnings. ............ ........................ .. 62
13.3.11 Configuring Network Warnings .... ................... ............ ....... 63
13.3.12 Storage ......... ............ ........................ ....... ............ ........ 63
13.3.13 Configuring the Video Recording Schedule ....... ....... ............ 64
13.3.14 Configuring Pre-Recording .... ............ ................... ............ 64
13.3.15 Configuring the Snapshot Schedule ........... ............ ....... ..... 65
13.3.16 Configuring Holidays... ............ ............ ............ ............ .... 66
13.3.17 Formatting the Hard Drive .... ............ ............ ................... . 67
13.3.18 Configuring Hard Drive Type ....... ....... ............ ............ ....... 68
#LX400070; r. 1.0/27147/27147; en-US
vi
Table of contents
13.3.19 Configuring General System Settings ........... ..... ....... .......... 68
13.3.20 Setting the Monitor Resolution (Display)................. ............. 69
13.3.21 Saving Your System Configuration to a USB Thumb
Drive ........... ............ ............ ....... ........................ ......... 70
13.3.22 Setting the System to Factory Defaults.......... ....... ..... .......... 71
13.3.23 Upgrading Firmware from USB........ ............ ....... ..... .......... 72
13.4 Shutdown....... ............ ............ ............ ....... ........................ ...... 73
14 Connecting to Your System Over the Internet on PC or Mac .... ............ .... 74
14.1 System Requirements...... ............ ............ ................... ..... .......... 74
14.2 Step 1 of 3: Connect your System to Your Router ....................... ...... 74
14.3 Step 2 of 3: Obtain the system’s Device ID......... ....... ..... ................. 75
14.4 Step 3 of 3: Connect to the System Over the Internet ....... ............ ..... 75
15 Using FLIR Cloud™ Client for PC or Mac .. ............ ............ ............ ........ 79
15.1 Home Page ........... ............ ............ ................... ............ ........... 79
15.2 Live View ........... ........................ ................... ............ ............ .. 79
15.2.1 Live View Controls ........................ ................... ............ ... 80
15.2.2 Opening Live View in Multiple Monitors .. ..... ................... ..... 81
15.3 Controlling PTZ Cameras . ........................ ....... ............ ............ ... 82
15.3.1 PTZ Presets ....... ............ ............ ............ ................... .... 83
15.3.2 PTZ Tours........ ....... ..... ................... ............ ............ ...... 84
15.3.3 PTZ Pattern ......... ............ ............ ....... ........................ .. 85
15.3.4 PTZ Scan ....... ........................ ....... ............ ............ ....... 86
15.3.5 PTZ Pan. ....... ............ ............ ............ ................... ........ 86
15.4 Playback. ........................ ....... ............ ............ ............ ............. 86
15.5 Playback Controls .. ............ ............................... ............ ............ 88
15.6 Downloading Video to your Computer Hard Drive...... ................... .... 89
15.7 Alarm ...... ..... ....... ............ ............ ............ ................... ............ 90
15.8 Log...................... ................... ............ ............ ............ ....... .... 91
15.9 E-map ........... ....... ............ ............ ............ ........................ ...... 92
15.10 Devices .. ............ ............ ............ ....... ........................ ............ . 94
15.11 Device Config ....... ............ ....... ........................ ............ ............ 95
15.12 Alarm CFG .. ........................ ............ ........................ ....... ......... 95
15.13 Tour & Task . ............ ............ ............ ....... ........................ ......... 98
15.14 Account .. ........................ ....... ............ ............ ............ ............ . 99
15.14.1 Managing User Accounts ............ ............................... ...... 99
15.14.2 Managing Roles... ............ ............ ............ ....... ..... ........ 101
15.15 General ........... ............ ............ ............ ............ ....... ............ .. 102
15.15.1 Basic ...... ............ ............ ............ ....... ........................ 102
15.15.2 File .............. ....... ............ ............ ............ ............ ...... 102
15.15.3 Alarm Prompt ......... ............ ............ ............ ....... .......... 103
15.15.4 Version . ............ ............ ............ ............ ....... ............ .. 104
16 Connecting to your System Using Smartphone or Tablet Apps... ........... 105
16.1 iPhone..................... ....... ............ ............ ............ ............ ...... 105
16.1.1 Prerequisites.... ....... ..... ................... ............ ............ .... 105
16.1.2 Connecting to your System on iPhone.... ....... ..... ............... 105
16.1.3 Live View Interface ....................... ....... ............ ............ . 106
16.1.4 Controlling PTZ Cameras. ....... ............ ............ ............ ... 107
16.1.5 Viewing Snapshots and Videos with Local Files ......... ....... .. 108
16.1.6 Using Playback Mode on iPhone . ............ ............ ............ 109
16.1.7 Enabling Push Notifications ........... ............ ................... .. 110
#LX400070; r. 1.0/27147/27147; en-US
vii
Table of contents
16.1.8 Using the Event List ...... ............ ................... ............ ..... 112
16.1.9 Using Favorites. ............ ............ ....... ........................ .... 113
16.1.10 Using the E-Map . ............ ............ ............ ................... .. 114
16.1.11 Device Manager......... ....... ............ ............ ............ ....... 116
16.1.12 Adding Devices Using an IP or DDNS Address
(Advanced).......... ............ ............ ............................... 117
16.2 iPad ............ ............ ................... ............ ............ ............ ...... 119
16.2.1 Prerequisites.... ....... ..... ................... ............ ............ .... 119
16.2.2 Connecting to your system on an iPad ................ ....... ....... 119
16.2.3 Live View Interface ....................... ....... ............ ............ . 120
16.2.4 Controlling PTZ Cameras. ....... ............ ............ ............ ... 121
16.2.5 Using Playback Mode on iPad..... ............ ....... ................. 122
16.2.6 Using Local File to View Manual Recordings ......... ............. 124
16.2.7 Enabling Push Notifications ........... ............ ................... .. 125
16.2.8 Using the Event List ...... ............ ................... ............ ..... 127
16.2.9 Using Favorites. ............ ............ ....... ........................ .... 128
16.2.10 Using the E-Map . ............ ............ ............ ................... .. 129
16.2.11 Using the Device Manager ............. ............ ............ ........ 131
16.2.12 Adding Devices Using an IP or DDNS Address
(Advanced).......... ............ ............ ............................... 131
16.3 Android ......... ....... ............ ............ ............ ........................ .... 134
16.3.1 Prerequisites.... ....... ..... ................... ............ ............ .... 134
16.3.2 Connecting to your System on Android .... ....... ............ ...... 134
16.3.3 Live View Interface ....................... ....... ............ ............ . 135
16.3.4 Controlling PTZ Cameras. ....... ............ ............ ............ ... 136
16.3.5 Viewing Snapshots and Videos with Local Files ......... ....... .. 137
16.3.6 Using Playback Mode on Android ......... ..... ....... ............ ... 137
16.3.7 Enabling Push Notifications ........... ............ ................... .. 139
16.3.8 Using the Event List ...... ............ ................... ............ ..... 140
16.3.9 Using Favorites. ............ ............ ....... ........................ .... 140
16.3.10 Using the E-Map . ............ ............ ............ ................... .. 142
16.3.11 Device Manager......... ....... ............ ............ ............ ....... 143
16.3.12 Adding Devices Using an IP or DDNS Address
(Advanced).......... ............ ............ ............................... 144
17 DDNS Setup (Advanced) ........... ............ ....... ............ ............ ............ 146
17.1 Accessing your System within a Local Network (LAN) .............. ....... 146
17.1.1 Step 1 of 3: Connect your System to Your Router ...... .......... 146
17.1.2 Step 2 of 3: Obtain the System’s Local IP Address .... ........... 147
17.1.3 Step 3 of 3: Connect to the System’s Local IP
Address .. ........................ ............ ............ ............ ....... 147
17.2 DDNS Setup—Access your System Remotely over the
Internet... ........................ ....... ............ ............ ............ ........... 149
17.2.1 Step 1 of 4: Port Forwarding .............. ....... ............ .......... 150
17.2.2 Step 2 of 4: Create a DDNS Account . ............ ............ ....... 150
17.2.3 Step 3 of 4: Enable DDNS on the System .... ................... ... 154
17.2.4 Step 4 of 4: Connect to the System’s DDNS Address ...... ..... 154
18 Connecting a PTZ Camera (LNR110 Series) ...... ............ ............ .......... 158
18.1 Controlling a PTZ Camera (Local NVR) ....... ............ ............ ........ 158
18.2 Advanced PTZ Controls .. ............ ....... ..... ................... ............ .. 158
18.2.1 Presets ....... ....... ........................ ............ ............ ........ 159
18.2.2 Tours ................... ............ ............ ............ .................. 160
#LX400070; r. 1.0/27147/27147; en-US
viii
Table of contents
18.2.3 Pattern ......... ............ ............ ....... ........................ ....... 160
18.2.4 Auto Scan ....... ....... ..... ................... ............ ............ .... 161
19 LNR110 Series Hard Drive Installation.. ....... ............ ............ ............ ... 162
19.1 Installing a Hard Drive ............ ....... ............ ............ ............ ....... 162
19.2 Removing the Hard Drive...... ..... ................... ............ ............ .... 164
19.3 Formatting Hard Drives ....... ........................ ....... ............ .......... 166
20 Recording Audio .. ................... ............ ............ ............ ............ ........ 167
20.1 Step 1 of 2: Connecting an audio-capable camera ....... ............ ...... 167
20.2 Step 2 of 2: Configuring audio recording .. ............ ............ ............ 168
21 LNR110 Series Troubleshooting ........... ............ ............ ............ ....... .. 169
22 LNR110 Series System Specifications...... ....... ........................ ........... 171
22.1 System ............ ............ ................... ............ ............ ............ .. 171
22.2 Inputs/Outputs ......... ............ ............ ............................... ....... 171
22.3 Display ........... ..... ....... ............ ............ ....... ..... ................... ... 171
22.4 Recording ....... ............ ............ ................... ..... ....... ............ ... 171
22.5 Playback and Backup ......... ............ ............ ............ ................. 172
22.6 Storage & Archive .. ............ ....... ........................ ............ .......... 172
22.7 Connectivity....... ................... ........................ ............ ............. 172
22.8 General ........... ............ ............ ............ ............ ....... ............ .. 172
22.9 Recording Resolution (Pixels) & Speed (FPS — Frames per
second) ............. ............ ............ ............ ............................... 173
23 Notices.............. ..... ....... ............ ............ ............ ............ ....... .......... 174
23.1 FCC/IC Notice........ ............ ............ ............ ....... ..................... 174
23.2 Modification........ ............ ............ ................... ........................ 174
23.3 ROHS .............. ....... ............ ............ ............ ............ ....... ...... 174
#LX400070; r. 1.0/27147/27147; en-US
ix
1
Important Safeguards
In addition to the careful attention devoted to quality standards in the manufacturing process of your product, safety is a major factor in the design of every instrument. However,
safety is your responsibility too. This sheet lists important information that will help to ensure your enjoyment and proper use of the product and accessory equipment. Please read
them carefully before operating and using your product.
1.1 General Precautions
1. All warnings and instructions in this manual should be followed.
2. Remove the plug from the outlet before cleaning. Do not use liquid aerosol detergents.
Use a water-dampened cloth for cleaning.
3. Do not use this product in humid or wet places.
4. Keep enough space around the product for ventilation. Slots and openings in the storage cabinet should not be blocked.
5. It is highly recommended to connect the product to a surge protector to protect from
damage caused by electrical surges. It is also recommended to connect the product to
an uninterruptible power supply (UPS), which has an internal battery that will keep the
product running in the event of a power outage.
CAUTION
Maintain electrical safety. Power line operated equipment or accessories connected to this product
should bear the UL listing mark or CSA certification mark on the accessory itself and should not be modified so as to defeat the safety features. This will help avoid any potential hazard from electrical shock or
fire. If in doubt, contact qualified service personnel.
1.2 Installation
1. Read and Follow Instructions - All the safety and operating instructions should be
read before the product is operated. Follow all operating instructions.
2. Retain Instructions - The safety and operating instructions should be retained for future reference.
3. Heed Warnings - Comply with all warnings on the product and in the operating
instructions.
4. Polarization - Do not defeat the safety purpose of the polarized or grounding-type
plug.
A polarized plug has two blades with one wider than the other.
A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety.
If the provided plug does not fit into your outlet, consult an electrician for replacement
of the obsolete outlet.
#LX400070; r. 1.0/27147/27147; en-US
1
1
Important Safeguards
5. Power Sources - This product should be operated only from the type of power source
indicated on the marking label. If you are not sure of the type of power supplied to your
location, consult your video dealer or local power company. For products intended to
operate from battery power, or other sources, refer to the operating instructions.
6. Overloading - Do not overload wall outlets or extension cords as this can result in the
risk of fire or electric shock. Overloaded AC outlets, extension cords, frayed power
cords, damaged or cracked wire insulation, and broken plugs are dangerous. They
may result in a shock or fire hazard. Periodically examine the cord, and if its appearance indicates damage or deteriorated insulation, have it replaced by your service
technician.
7. Power-Cord Protection - Power supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or against them. Pay particular
attention to cords at plugs, convenience receptacles, and the point where they exit
from the product.
8. Surge Protectors - It is highly recommended that the product be connected to a
surge protector. Doing so will protect the product from damage caused by power
surges. Surge protectors should bear the UL listing mark or CSA certification mark.
9. Uninterruptible Power Supplies (UPS) - Because this product is designed for continuous, 24/7 operation, it is recommended that you connect the product to an uninterruptible power supply. An uninterruptible power supply has an internal battery that will
keep the product running in the event of a power outage. Uninterruptible power supplies should bear the UL listing mark or CSA certification mark.
10. Ventilation - Slots and openings in the case are provided for ventilation to ensure reliable operation of the product and to protect it from overheating. These openings must
not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should never be placed
near or over a radiator or heat register. This product should not be placed in a built-in
installation such as a bookcase or rack unless proper ventilation is provided and the
product manufacturer’s instructions have been followed.
11. Attachments - Do not use attachments unless recommended by the product manufacturer as they may cause a hazard.
12. Water and Moisture - Do not use this product near water — for example, near a bath
tub, wash bowl, kitchen sink or laundry tub, in a wet basement, near a swimming pool
and the like.
13. Heat - The product should be situated away from heat sources such as radiators, heat
registers, stoves, or other products (including amplifiers) that produce heat.
14. Accessories - Do not place this product on an unstable cart, stand, tripod, or table.
The product may fall, causing serious damage to the product. Use this product only
with a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold
with the product. Any mounting of the product should follow the manufacturer’s instructions and use a mounting accessory recommended by the manufacturer.
15. Camera Extension Cables – Check the rating of your extension cable(s) to verify
compliance with your local authority regulations prior to installation.
16. Mounting - The cameras provided with this system should be mounted only as instructed in this guide or the instructions that came with your cameras, using the provided mounting brackets.
#LX400070; r. 1.0/27147/27147; en-US
2
1
Important Safeguards
17. Camera Installation - Cameras are not intended for submersion in water. Not all cameras can be installed outdoors. Check your camera environmental rating to confirm if
they can be installed outdoors. When installing cameras outdoors, installation in a
sheltered area is required.
1.3 Service
1. Servicing - Do not attempt to service this product yourself, as opening or removing
covers may expose you to dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
2. Conditions Requiring Service - Unplug this product from the wall outlet and refer
servicing to qualified service personnel under the following conditions:
• When the power supply cord or plug is damaged.
• If liquid has been spilled or objects have fallen into the product.
• If the product has been exposed to rain or water.
• If the product has been dropped or the cabinet has been damaged
• If the product does not operate normally by following the operating instructions. Ad-
just only those controls that are covered by the operating instructions. Improper adjustment of other controls may result in damage and will often require extensive
work by a qualified technician to restore the product to its normal operation.
• When the product exhibits a distinct change in performance. This indicates a need
for service.
3. Replacement Parts - When replacement parts are required, have the service technician verify that the replacements used have the same safety characteristics as the original parts. Use of replacements specified by the product manufacturer can prevent fire,
electric shock, or other hazards.
4. Safety Check - Upon completion of any service or repairs to this product, ask the
service technician to perform safety checks recommended by the manufacturer to determine that the product is in safe operating condition.
1.4 Use
1. Cleaning - Unplug the product from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp cloth for cleaning.
2. Product and Cart Combination - When product is installed on a cart, product and
cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.
3. Object and Liquid Entry - Never push objects of any kind into this product through
openings as they may touch dangerous voltage points or “short-out” parts that could
result in a fire or electric shock. Never spill liquid of any kind on the product.
4. Lightning - For added protection of this product during a lightning storm, or when it is
left unattended and unused for long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent damage to the product due
to lightning and power line surges.
#LX400070; r. 1.0/27147/27147; en-US
3
2
LNR110 Series Features
Features
• Full high definition 1080p recording.
• Real-time recording at 30fps per channel.
• 8 Built in PoE (Power Over Ethernet) ports providing video and power on a single Ether-
net cable.
• Automatically detects compatible IP cameras in the network.
• 24/7 security-grade hard drive.
• H.264 video compression.
2
2
• Expandable High Capacity Storage up to 4TB.
• Pentaplex operation - view, record, playback, backup & remotely control the system
simultaneously.
• Simultaneous playback and live view on the same screen.
• Selectable area digital zoom in live view and playback.
• Dynamic click-and-drag camera channel assignment.
• Convenient front panel button controls.
• Accurate time stamps with NTP & daylight savings time.
• Instant USB backup of live video from selected camera.
• 2 video outputs (HDMI & VGA) to connect multiple monitors.
• HDMI cable included for simple connection to HDTVs.
• Keep up to date with automatic firmware upgrades.
• 3-Step remote view with FLIR Cloud™.
• PC and Mac compatible.
6
5
4
• Free iOS and Android compatible apps with live viewing, playback, video recording,
and snap shot.
6
• Dedicated iPad app with multi-channel live viewing and playback.
• Push notifications of motion events.
• Instant email alerts with snap shot attachment.
• Dual streaming to conserve bandwidth.
• Continuous, scheduled and motion recording.
1
3
#LX400070; r. 1.0/27147/27147; en-US
4
2
LNR110 Series Features
NOTE
1. Compatible with select Lorex 1080p wired PoE HD cameras only. For a list of compatible cameras,
please visit www.lorextechnology.com/support
2. Recording time may vary based on recording resolution & quality, lighting conditions and movement
in the scene.
3. Instant playback feature available on one camera at a time during live view when in quad or multiple
camera viewing mode.
4. The NVR firmware and software must be upgraded to the latest version to use the FLIR Cloud™
service. When the system is connected to the Internet, it will automatically alert you if there is a firmware upgrade available.
5. Requires a high speed internet connection and a router (not included). A minimum upload speed of
1Mbps is required for the best video performance. Up to 3 devices may connect to the system at the
same time.
6. For the latest list of supported apps and devices, please visit www.lorextechnology.com/support
Use product in accordance with the instructions provided. All trademarks belong to their respective owners. No claim is made to the exclusive right to use the trademarks listed, other than the trademarks owned
by Lorex Corporation. We reserve the right to change models, configurations or specifications without notice or liability. Product may not be exactly as shown. Images are simulated.
#LX400070; r. 1.0/27147/27147; en-US
5
3
Getting Started (LNR110 Series)
The system comes with the following components:
NVR (Network Video Recorder) Power adapter
Ethernet cable HDMI cable
Hard drive size, number of channels, and camera configuration may vary by model. Please
refer to your package for specific details. Check your package to confirm that you have received the complete system, including all components shown above.
USB mouse
Quick start guides
#LX400070; r. 1.0/27147/27147; en-US
6
4
Front Panel (LNR110 Series)
1. NET: Glows when network is in normal state. Turns off for network error.
2. Power Indicator: Glows to indicate the system is on.
3. HDD: Glows to indicate hard drive is in normal state. Turns off when there is a hard
drive error.
4. USB Port: Connect a USB mouse (included) or connect a USB flash drive (not included) for data backup or firmware upgrades.
#LX400070; r. 1.0/27147/27147; en-US
7
5
LNR110 Series Rear Panel
1. MIC IN/OUT: Service only; not supported.
NOTE
Audio-enabled IP cameras (not included) are required to use audio recording. You cannot record
audio from the input (e.g. microphone) connected to the MIC IN port.
2. HDMI: Connect to an HDMI monitor or TV (not included) to view the system interface.
3. VGA: Connect a VGA monitor (not included) to view the system interface.
4. USB port: Connect a USB mouse (included) or USB thumb drive (not included) for data backup or firmware updates.
5. PoE Ports: Connect IP cameras. Integrated PoE (Power Over Ethernet) ports provide
power to cameras and video connection to NVR.
6. LAN: Connect a CAT 5 RJ45 Ethernet cable for local and remote connectivity.
7. Power input: Connect the included power adapter.
#LX400070; r. 1.0/27147/27147; en-US
8
6
Basic Setup (LNR110 Series)
6.1 Step 1: Connect the IP Cameras
Option 1: Direct Connection to NVR
• Connect cameras to the PoE Ports on the rear panel of the NVR using Cat5e or higher
grade Ethernet cable. The cameras will appear on the NVR without any additional configuration when the system starts up.
NOTE
Compatible with select Lorex 1080p wired PoE HD cameras only. For a list of compatible cameras,
please visit www.lorextechnology.com/support
Connect IP cameras directly to PoE ports.
Option 2: Connect Cameras to Local Network
You can also connect your IP cameras to your local network for flexible installations. You
will need to do this to connect cameras 9~16 to 16–channel models. For details, see 6.11
Connecting Cameras to the Local Area Network (LAN), page 13.
6.2 Step 2: Connect the Mouse
• Connect a USB mouse (included) to one of the USB ports.
#LX400070; r. 1.0/27147/27147; en-US
9
6
Basic Setup (LNR110 Series)
6.3 Step 3: Connect the Ethernet Cable
• Connect an Ethernet cable (included) to the LAN port on the rear panel of the system.
Connect the other end of the Ethernet cable to a router on your network.
6.4 Step 4: Connect the Monitor
• Connect the included HDMI cable from the HDMI port to the TV or monitor
(recommended).
OR
• Connect a VGA cable (not included) from the VGA port to the monitor.
1. HDMI port.
2. VGA port.
6.5 Step 5: Connect the Power Adapter to Power the NVR
• Connect the included AC power adapter to the NVR and connect the other end to a
power outlet or surge protector.
#LX400070; r. 1.0/27147/27147; en-US
10
6
Basic Setup (LNR110 Series)
At startup, the system performs a basic system check and runs an initial loading sequence.
After a few moments, the system loads a live display view.
6.6 Step 6: Upgrade Firmware to Latest Version (if Available)
If a firmware upgrade is available, you will be asked to install it once the system starts up.
It is required to upgrade your system firmware and client software or mobile apps to the latest version to enable remote connection to the system.
If a firmware upgrade is available:
1. After startup, a notification will appear asking you to upgrade the firmware. Click OK to
upgrade.
2. Enter the system user name (default: admin) and password (default: 000000) and
click OK. Wait for the firmware update to complete. The system will restart once the
firmware has been upgraded.
WARNING
DO NOT POWER OFF THE SYSTEM OR DISCONNECT THE POWER CABLE DURING FIRMWARE INSTALLATION
6.7 Step 7: Verify Camera Image
• Power on the cameras, and then verify the camera video quality before mounting the
cameras to a permanent location.
• Mount the cameras under a sheltered location. Always verify the outdoor rating of your
camera before installing it in a permanent location.
6.8 Step 8: Set the Time
• Set the system time and date for accurate video time stamps. Videos with inaccurate
times may not be valid as surveillance evidence.
• For details on setting the system time, see 8.8 Setting The Time, page 23.
6.9 Default System Password & Port Numbers
CAUTION
By default, the system user name is admin and the password is 000000. It is essential that you create
your own password. For details, see 12 Managing Passwords and User Accounts, page 40.
#LX400070; r. 1.0/27147/27147; en-US
11
6
Basic Setup (LNR110 Series)
The system requires a user name and password to log in to the system remotely using a
computer or mobile device. After logging on remotely the first time, you will be asked to
create a custom password for the system.
Local system and remote connectivity (LAN & Internet) user name and password:
• Username: admin
• Password: 000000
Default ports for DDNS remote access:
• Port 80 (HTTP port)
• Port 35000 (Client port)
6.9.1 FLIR Cloud™
This system features the exclusive FLIR Cloud™. This is a cloud service that allows you to
connect to your system over the Internet via a secure handshake with our servers. This
means you can easily connect to your system without requiring any network configuration.
For details on setting up your system to connect to the Internet using FLIR
Cloud™:
• See 14 Connecting to Your System Over the Internet on PC or Mac, page 74.
OR
• See 16 Connecting to your System Using Smartphone or Tablet Apps, page 105.
Connectivity using Lorex’s free DDNS service is also available, but requires the ports listed
above to be port forwarded on your router.
6.10 Quick Access to System Information
To quickly open a window that displays vital system information:
• Right-click to open the Quick Menu and click Info. Enter the system user name (default:
admin) and password (default: 000000).
NOTE
The QR code shown in the System Info screen can be scanned during mobile setup to enter the system’s
Device ID.
#LX400070; r. 1.0/27147/27147; en-US
12
6
Basic Setup (LNR110 Series)
6.11 Connecting Cameras to the Local Area Network (LAN)
For flexibility, you may also connect IP cameras to the same Local Area Network (LAN) as
the NVR. This is accomplished by connecting the cameras to the same router as the NVR.
For these installations, an external PoE switch (sold separately) or power adapter (sold
separately) must be used to provide power to each IP camera. You also must add the cameras on the NVR before they will show a picture on the monitor or be recorded by the NVR.
Follow the steps below to connect the cameras to the NVR over the LAN.
NOTE
• Compatible with Lorex 1080p wired PoE HD cameras only. For a list of compatible cameras, please
visit www.lorextechnology.com/support.
• Camera and NVR images in this section are used for illustration only.
Step 1 of 2 — Option A: Connecting cameras to your local network using a PoE
switch:
1. Connect an Ethernet cable from the LAN port on an external PoE switch (sold separately on www.lorextechnology.com) to your router using a CAT5e or higher Ethernet
cable. Connect the power cable to the PoE swtich and to a power outlet or surge
protector.
NOTE
Terminology may vary depending on the model of PoE switch you have.
2. Connect the IP cameras to the PoE switch using the Ethernet extension cables. The
PoE switch will provide power and video transmission the same way as your NVR.
#LX400070; r. 1.0/27147/27147; en-US
13
6
Basic Setup (LNR110 Series)
Step 1 of 2 — Option B: Connecting cameras to your local network using power
adapters:
1. Connect each camera to a compatible power adapter (visit www.lorextechnology.com
for compatible power adapters for your cameras).
2. Connect the camera to your router using a CAT5e or higher Ethernet cable.
Step 2 of 2: Add the cameras to your NVR:
1. Right-click and select Device Search .
2. Log in using the admin account (default User Name: admin; default Password:
000000).
3. Click Device Search. The system searches the network for compatible cameras.
4. Check the camera(s) you would like to add.
#LX400070; r. 1.0/27147/27147; en-US
14
6
Basic Setup (LNR110 Series)
5. Click Add. The Status indicator turns green to show the camera is successfully
connected.
6. Click OK to save changes.
NOTE
You can also add a camera to a specific channel by hovering the mouse over an empty channel in split-
screen view and clicking
. Then double-click the camera you would like to add and right click to exit.
#LX400070; r. 1.0/27147/27147; en-US
15
7
Mouse Control
The mouse is the primary control device for the system. To connect a USB mouse:
• Connect a USB mouse to the USB port on the front or rear panel.
1. Left-button:
• In live view, click to open the Navigation Bar. Right-click to close the navigation bar.
• In live view, while in a split-screen display mode, double-click an individual channel
to view it in full-screen. Double-click again to return to the split-screen display mode.
• While navigating menus, click to open a menu option.
2. Right-button:
• During live view, right-click anywhere on the screen to open the Quick Menu.
• Within system menus, right-click to exit menus.
3. Scroll wheel: In live view, use the scroll wheel to zoom in/out.
#LX400070; r. 1.0/27147/27147; en-US
16
8
Using the System
Use the system’s graphical on-screen display to navigate menus and configure options
and settings.
8.1 On-Screen Display
The system shows the following for all display views:
1. Display area:
• Double-click on a channel to view in full-screen; double-click again to return to split
screen.
• Right-click to open the Quick Menu.
• Left-click to open the Navigation Bar.
• Move the mouse to the top of a channel to view the Camera Toolbar.
• Click-and-drag cameras to rearrange the channel display. This does not affect the
channels each camera is connected or recording to.
2. Channel name
3. C: Camera is continuously recording.
4. M: Motion has been detected.
5. Date & time: Current system date and time. For details on setting the date and time,
see 8.8 Setting The Time, page 23.
8.2 Using the Quick Menu
The Quick menu gives you access to the system’s key functions. To access the Quick
Menu, right-click the screen during live view.
#LX400070; r. 1.0/27147/27147; en-US
17
8
Using the System
The Quick Menu has the following options:
• View: Select a camera in full-screen or select a multi-channel display.
• PTZ: Access controls for PTZ cameras (not included).
• AutoFocus: Access zoom/focus controls for auto-focus cameras (not included).
• Camera Setting: Configure image settings for cameras.
• Info: Opens the system information window.
• Sequence: Click to start/stop sequence mode.
In sequence mode, the system will automatically cycle through connected cameras
every few seconds. A
will appear to show that sequence mode is on.
Click the icon to pause sequence mode on the channel that is currently shown (icon
changes to
). Click again to resume sequence mode.
Right-click and select Sequence to return to normal viewing mode.
• Disable Beep: Turns off the beeping noise.
• Search: Search/playback recorded video. See 10 Search (Playback), page 28.
• Manual Control: Click Record to open the Record menu to select manual recording
options. See 9.3 Setting up Scheduled or Manual Recording, page 25.
• Device Search: Open the Device Search menu to manage IP cameras over the local
network.
• Main Menu: Open the Main Menu. See 13 Using the Main Menu, page 44.
8.3 Adjusting Camera Image Settings
Use the Camera Setting menu to adjust image settings for your cameras.
To adjust image settings:
1. Right-click on the channel you would like to configure and select Camera Setting. Enter the system password if prompted.
#LX400070; r. 1.0/27147/27147; en-US
18
8
Using the System
2. Configure the following settings as needed:
NOTE
The settings listed below are only shown if they are supported on the selected camera. Some camera
models do not support all settings.
• Mirror: Select Enable to flip the image horizontally.
• Flip: Select Flip 180° to flip the image vertically, or select No Flip for the default
orientation.
• Corridor Mode: Not supported.
• BLC Mode: Select High or Low to enable back light compensation or Off to dis-
able. Back light compensation adjusts the lighting levels in the picture so you can
see objects in the foreground if there is a strong light source behind them.
• Scene Mode: The Scene Mode allows you to adjust white balance levels for the
camera. Select Schedule for the camera to automatically adjust the white balance.
Select Sunny or Night to use preset white balance levels. Select Customized to
manually set blue and red levels.
• Day&Night: This setting sets the camera’s day/night mode. Select Colorful for the
camera to use color mode at all times. Select Schedule for the camera to automatically determine whether to use color or black and white mode. Select Black&White
for the camera to use black and white mode at all times.
NOTE
It is recommended to select Schedule mode, as using Colorful may impact the camera’s performance at night.
• Saturation: Adjust the vibrancy of colors in the image.
• Brightness: Adjust the image brightness.
• Contrast: Adjust the image contrast.
• Hue: Adjust the color hue of the image.
#LX400070; r. 1.0/27147/27147; en-US
19
8
Using the System
3. Click OK to save changes.
NOTE
You must save changes to apply settings changes. It is recommended to adjust one setting at a time
so you can see the results of each change. Click Default to reset the camera to default image
settings.
8.4 Using the Navigation Bar
The Navigation Bar gives quick access to certain functions and menus.
To open the Navigation bar:
• Left click on the screen to open the Navigation Bar. The Navigation Bar has the follow-
ing options:
1. Main Menu.
2. Collapse.
3. Select display layout.
4. Sequence: Click to start/stop sequence mode.
5. PTZ: Click to open PTZ controls.
6. Camera Setting: Click to open camera image settings.
7. Search: Search and playback recorded video. See 15.4 Playback, page 86.
8. Event: View events in progress. See 13.2.4 Event Info, page 51.
9. Channel Info: Click to access status information about connected cameras.
10. Remote Device: Manage IP cameras over the network.
11. Network: Configure network settings for your system. See 13.3.1 Network, page 54.
12. HDD Manager: Manage hard drives connected to the system. See 13.3.17 Format-
ting the Hard Drive, page 67.
13. USB Manager: Click to access options for connected USB thumb drives (not included). You can backup video, logs, or system configurations and install firmware
upgrades.
14. System Upgrade: Check for firmware upgrades. The system must be connected to
the Internet to check for or receive updates.
8.5 Using the Camera Toolbar
The Camera Toolbar is used to perform actions on a specific channel.
To access the Camera Toolbar:
• Move the mouse to the top of the channel display. The Camera Toolbar has the following options:
#LX400070; r. 1.0/27147/27147; en-US
20
Loading...