Lorex LNZ4001, LNE1001 Quick Setup Manual

Page 1
DISCOVER & VIEW YOUR CAMERA ON THE LOCAL NETWORK
STEP 2
Skill Level
Time
under 30 minutesunder 15 minutes under 60 minutes
Hand Tools Hardware
Router
Hi Speed
over 60 minutes
Time: 10 Minutes
Hand Tools
- Computer
Skills - Easy
BAS IC I NST ALL AT ION G UI DE
NOTE: This quick start guide refers to a Windows Vista™, installation.
Pop-up security windows may differ in Windows XP™. Installation is easy in both versions of the operating system.
NOTE: For initial setup, you will need Internet Explorer as your default browser. Do not install DigiConsole until Step 2 is completed.
Launching the DigiConsole Software
Before launching the program, please make sure your computer is connected to the same local network as the camera and has access to the Internet. The camera must be connected using the included Ethernet cable for initial installation. It is recommended to setup the camera when your computer is wired to the local network. If you are using the wireless connection on your computer, please make sure you are connected to your wireless router (check wireless name - SSID).
If the software runs automatically, please proceed to Step 2, section d.
If the pop-up window appears, click Run DigiConsole.exe and continue to Step 2, section c.
b
Double-click the camera to launch DigiViewer in your browser.
a
Enter admin in the username and admin in the password fields to access your camera. The browser will prompt you to install ActiveX.
b
Depending on your browser security settings, you can use the “remember me” check option and the next time you will view the same camera using this browser it will renumber user name and password till you restart your computer.
Did you know?
If a security pop-up window appears, click Unblock and Continue to allow DigiConsole to run.
c
NOTE: If the CD does not start
automatically, please go to “Computer” (“My Computer” for Windows XP™ users) and double click on the CD Drive to run the application. Follow Step 2.
Click Find to discover Lorex cameras on your network.
OPTION: If UPNP is enabled on your computer open the “Network” (“My Network Places” for Windows XP™ users) folder to view UPnP devices. (UPNP is disabled by default in Windows Vista™).
d
a
Insert the included DigiConsole Software CD into your CD/DVD-ROM drive.
Local Viewing
Congratulations! Your camera is
now set-up for local viewing
d
If a security pop-up window appears, click Unblock and Continue. Click the warning on the browser bar and select Install ActiveX
Control. Click Unblock or Continue in any proceeding
security pop-ups.
c
Click the warning bar (it will turn from yellow to blue) and select Install ActiveX.
Click Install to start the installation. Click Unblock or Continue in any security pop-up. (This step is required only for first time set-up).
LNE Series
Quick Setup Guide
It really is that easy!
BEFORE YOU START
This Network Camera is designed for easy installation. However, before you continue, please read the following:
The Quick Start Guide refers to LNE1001, LNE3003 and LNZ4001 models and must be followed in sequence without skipping steps.
1. When setting up the camera, use Internet Explorer only After the initial setup, you can view the camera using Internet Explorer (with ActiveX), Mozilla Firefox and Safari
2. Steps 1 - 2 should to be completed when your camera is connected wired before you can use the camera wirelessly.
3. When connecting the camera to a wireless network, consider the following: a. If your wireless router is not set up with wireless encryption, you can start the installation process immediately. b. If your wireless router is set up with the encryption, please make sure you know the encryption key. If you do not know the encryption key (encryption password), please refer to your router’s manual in order to reset the key. c. If your wireless router is set up with a different type of encryption please refer to your router’s manual in order to change encryption type to WEP. d. The camera is compatible with Macintosh for viewing only. Recording on Macintosh is not supported. To set up camera using Macintosh auto discovery “Bonjoure” can be used, advanced knowledge is required. Please refer to “Setting Up Using Macintosh” FAQ on LOREX web site www.lorexcctv.com
under 30 minutesunder 15 minutes under 60 minutes
Hand Tools Hardware
Hi Speed
over 60 minutes
Skill Level
Time
under 30 minutesunder 15 minutes under 60 minutes
Hand Tools Hardware
Router
Hi Speed
over 60 minutes
Time: 10 Minutes
Hand Tools Skills - Easy
BAS IC I NST ALL AT ION G UI DE
SET UP YOUR CAMERA FIRST
STEP 1
Broadband Router and Computer are required for local and remote monitoring (not included).
Place the base of the camera on a flat surface and screw on the stand.
a
Attach the screw knob to the camera stand.
b
Attach the wireless antenna to the back of the camera.
c
Screw the camera to the camera stand.
d
Tighten the screw knob to secure the camera.
e
Plug the power adaptor into the power port of the camera. Plug the other end to an electrical outlet.
NOTE: Make sure the LED is lit on the front of the camera. If not, check that all cables are properly connected.
g
Set up Your Camera
f
Connect the included network cable to the rear side of the LAN port on the bottom of the camera. Connect the other end of the network cable to the router, switch, or active wall port of your local network.
IMPORTANT
5. Reset
6. Audio IN
7. Audio OUT
8. I/O
1. Camera
2. Antenna
3. Power Adaptor Port
4. Ethernet Cable (LAN) Port
USING ZOOM AND PAN/TILT FEATURE
STEP 3
Skill Level
Time
under 30 minutesunder 15 minutes under 60 minutes
Hand Tools Hardware
Router
Hi Speed
over 60 minutes
Time: 10 Minutes
Skills - Easy
BAS IC I NST ALL AT ION G UI DE
Hand Tools
- Computer
2
1
4
3
5
3
5
4
2
1
6 7 8
LNE3003
LNZ4001
From DigiViewer, once you are able to view the video using the
browser, click the PTZ icon . A Pan/Tilt control panel will appear on the left side of DigiViewer.
a
b
NOTE: This step refers to LNZ4001 camera model and shows only basic
functionality of Pan/Tilt feature. For a full instruction on all Pan/Tilt functionality, please refer to manuals in CD
Click the arrows to control Pan and Tilt.
Zoom Out
Zoom IN
Preset & Patrol
Navigation Arrows
Preset & Patrol:
NOTE: The Preset and Patrol are advanced features, for a full instruction on setting up these features; please refer to manuals in CD.
c
Using the arrows, position the camera to point to where you want it to patrol. From the Pan/ Tilt control panel click Set.
Then click the Set button beside
Preset Go.
Click Go Back. Repeat step C until you complete the Patrol positions you require. (You can set up to 32 positions; each Tour can have up to 8 positions).
• From DigiViewer, click Events and then select Patrol.
• Select the Tour number (E.g.: Tour 1)
• Select Order (first will be the default position)
Select Preset Position (the positions you set in Step 3c), then click Set.
Repeat the order and position selection until you have your tour completed with all required positions (each Tour can have up to 8 positions). Click Submit Patrol.
d
e
• From DigiViewer, click the Surveillance, click the Play icon and click the PTZ icon .
• From Pan/Tilt control panel click Set then click the Set button beside Patrol Go.
• Select the Tour number you set up in Step 3d and click the Patrol Go button.
Congratulations! Your camera is now set-up for Zoom and Pan/Tilt feature
Information in thi s document is s ubject to ch ange withou t notice. As o ur product s are subjec t to continuous impr ovement, Lo rex Technolog y INC. and our su bsidiari es reser ve the right to modify produc t design, sp ecificati ons and price s, withou t notice and wi thout incur ring any obligation. E&O E © 2009 LORE X. All ri ghts reser ved.
iPhone™, iPod touc h™, Yoics™, and MS N™ are regis tered trad emarks of the ir respec tive companies, reg istered in th e United State s and other cou ntries. iP hone™ and iPod t ouch™ are not included in this p ackage.
It’s all on the Web
www.lorexcctv.com
For detailed setup information, please refer to your User’s Manual. For additional information, please visit our website www.lorexcctv.com
ALSO AVAILABLE:
16-CHANNEL INTELLIGENT SURVEILLANCE SOFTWARE SOLUTION
Integrated Systems and Accessories. Order whatever you need at
www.lorexcctv.com or call 1-888-42-LOREX (1-888-425-6739)
SEE HEAR PROTECT
PROTECT EVERYTHING
THAT MATTERS
Warehouse
LNP5220E, LNP5320E, LND7220V, LNZ9320W
Offi ce
LNE3003 , LNP5220E, LND7220V
Day Care
LNE3003, LNP5220E
Convenience Store
LND7220V, LNE3003
LNP5220E, LND7220V
Restaurant
Home Offi ce
LNE3003
Add wired or wireless network cameras to
expand the “Envelope of Protection” for your
business, your home and your family
Drive Way / Parking Lot Front Door
LNE3003
Nursery
LNE3003
Backyard
LNP5320E, LND7220VLNP5320E, LNB6300V
LNZ4001
LNE1001
LDP1601
Page 2
Skill Level
Time
under 30 minutesunder 15 minutes under 60 minutes
Hand Tools Hardware
Router
Hi Speed
over 60 minutes
Time: 10 Minutes
Hand Tools
- Computer
Skills - Easy
BAS IC I NST ALL AT ION G UI DE
SET UP YOUR CAMERA ON THE WIRELESS LOCAL NETWORK
Setting up the Camera to be Wireless
NOTE: By default, the Wireless feature in the camera is disabled. If the
wireless connection is set up with encryption, you will be asked to provide the encryption key.
NOTE:
Wireless cameras require a power source to operate. Use the
included camera power adaptor.
STEP 8
CAMERA must be PLUGGED INTO YOUR ROUTER BEFORE STARTING THE WIRELESS SETUP. Steps 1 - 2 should to be completed.
From DigiViewer, click Settings, Wireless and then select Enabled when scrolling down the Wireless
Mode option.
a
Click OK on the pop-up warning.
Wait approximately one minute to allow the camera to complete connection to the wireless router. Go back to DigiConsole (Step 2) and click Find till you see the same camera listed twice. Remove the network cable and continue to Step 6, section d. If the camera is not listed twice go back to Step 6, section a, select Wireless Mode: Disable. Wait till camera is done updating, then repeat Step 6, section a again.
c
1. Close the Internet Browser
2. Go back to the DigiConsole screen, right click on the shown camera and select Refresh. (If DigiConsole was closed earlier, run the software again and click Find).
3. Double-click the camera to launch DigiViewer in your browser.
d
The Camera will scan for available wireless network.
Highlight the network you want the camera to be connected to.
If the wireless connection is set up with encryption, Please provide the encryption key.
Click Connect.
b
Congratulations! Your
camera is now set-up to
work Wireless.
RECORD AND PLAYBACK YOUR CAMERA ON THE LOCAL NETWORK
STEP 4
Skill Level
Time
under 30 minutesunder 15 minutes under 60 minutes
Hand Tools Hardware
Router
Hi Speed
over 60 minutes
Time: 10 Minutes
Skills - Easy
BAS IC I NST ALL AT ION G UI DE
Hand Tools
- Computer
Playback
Click Playback, if viewing or recording is enabled on DigiConsole, you will be prompted to stop live viewing. Click OK.
a
b
Select the desired cameras and recording date from the list to play. Right click and select Play
Back Recorded Video.
Use DigiConsole to playback (repeat Step 2, sections a - c to run from CD).
Your default player (e.g. Windows Media Player) will play the selected video.
c
Recording (Video Only)
NOTE: Playback requires Windows Media Player and Xvid codec. A link to
Xvid can be found on the Home page of DigiConsole.
Use DigiConsole to record (repeat Step 2, sections a - c to run from CD).
Click Install to start the installation in the DigiConsole.
a
b
Click Next at the bottom right corner and when asked, read and accept the license.
The process takes few minutes. Click OK to proceed with installation.
c
Double click to open the DigiConsole icon from your desktop.
e
f
Find and detect your camera (Step 2, section d)
Right click the camera icon and select View live video. Wait till you see the streaming video.
g
d
Click the red X on top right corner to close DigiConsole.
h
Right click the camera icon and select Record Video Image. You are now recording on to your local computer.
NOTE: DigiConsole supports up to 6 cameras and include basic recording option (ON or OFF only). For advanced software DIGIplayer please visit our web www.lorexcctv.com
Congratulations! Your
camera is now ready to
record and playback on the
local network
SET UP REMOTE EASY CONNECT (YOICS ™) TO VIEW YOUR CAMERA
ANYWHERE ANYTIME
STEP 5
A: Yoics Sign-up
From DigiViewer, click Settings, Remote Access and then click Register with Yoics at the bottom right of the Yoics section.
On your Yoics account page, Click Yes on the Security Pop-up Window.
a
a
Your new Camera is detected and becomes available to be added to your Yoics account.
From the LOREX pop-up window click Complete Registration.
The Register New Devices page opens.
b
NOTE: By default, the LNE3003 IP Camera is enabled for Yoics™ easy-connect
remote access.
OPTION: If you prefer to view your camera remotely more often, for epitomized viewing, from the DigiViewer main menu, click Settings and then click Device Setup. From the Video Streaming pull-down menu, selecting the last option to change the video streaming quality to a lower network bandwidth.
B: Camera Registration
You need to provide the LOREX Camera two different registration names (The first will register your camera to stream using web browser the second is to be able to view using iPhone™/iPod touch™). Enter a name for the camera in the Yoics Device Name. Click Register Now.
c
If the camera does not appear Under “My Stuff”, Press F5 on your keyboard to refresh the page.
Powered by
Quicktime Player is required for Remote Viewing using Yoics. http://www.apple.com/quicktime/download/
Skill Level
Time
under 30 minutesunder 15 minutes under 60 minutes
Hand Tools Hardware
Router
Hi Speed
over 60 minutes
Time: 10 Minutes
Hand Tools
- Computer
Skills - Easy
BAS IC I NST ALL AT ION G UI DE
On the log-in website page, enter the required personal information in the fields and click
Register.
b
Depending on your browser security settings, you can use the “remember me” check option and the next time you will log in to Yoics from this browser it will remember user name and password till you restart your computer.
Did you know?
VIEWING YOUR CAMERA VIA THE INTERNET
Remote Viewing using Web Browser
STEP 6
Powered by
Skill Level
Time
under 30 minutesunder 15 minutes under 60 minutes
Hand Tools Hardware
Router
Hi Speed
over 60 minutes
Time: 10 - 30
Minutes
Hand Tools
- Computer
Skills - Easy
BAS IC I NST ALL AT ION G UI DE
Browse to http://lorex.yoics.com and log in using the user name and password you created in Step 5, section b. Under My Stuff, click the camera you want to view.
You may be prompted to install QuickTime or asked to enter the Username and Password (default admin, admin) to login to the camera.
a
NOTE: Number of simultaneous connections possible to the camera
depends on Internet bandwidth.
You can share the camera with other Yoics users. Refer to the provided manual on the http://www.yoics.com website.
EXPERT OPTION:
If you have an external (WAN) static IP address or you have registered with the free LOREX DDNS service, you can configure your router to port-forward the incoming Internet connections to the camera. Use the static IP address or your customized lorexddns.net URL in the address field of your browser to access your camera. Yoics registration is not required when using this option. For more details, please refer to the instruction manual on the CD.
NOTE: For security reasons change the default admin password login to the camera. For more details, please refer to the instruction manual on the CD.
Congratulations! Your camera is now set-up for remote viewing on any PC
Congratulations! Your camera is
now set-up for remote viewing on
your iPhone™ or iPod touch™.
REMOTE VIEWING WITH i Phone™ / iPod touch™
STEP 7
Skill Level
Time
under 30 minutesunder 15 minutes under 60 minutes
Hand Tools Hardware
Router
Hi Speed
over 60 minutes
Time: 10 Minutes
Tools Skills - Easy
BAS IC I NST ALL AT ION G UI DE
Using the Safari browser, go to http://lorex.yoics. com and log in using your Yoics username and
password.
a
Click the camera you want to view.
b
Enter the username and password to log in to the
camera (default admin, admin).
c
OPTION: In newer versions of
iPhone™ /iPod Touch™, you can bookmark the Yoics website for quick access. Alternatively create a shortcut on the application screen for easy access. Check the reference materials that came with your iPhone™ / iPod touch™ for feature details.
Advanced OPTION: If you set up the camera using an external static IP or DDNS, use the iPhone™ /iPod Touch TM browser, simply typing in the IP/DDNS address.
Powered by
NOTE:
If your wireless network name ID (SSID) includes a “space”, please refer to the router manual for changing the SSID without a “space” (E.g.: Lorex Wireless --> LorexWireless)
LNZ4001 LNE1001 LNE3003
Loading...