Lorex LBV1521B, LBV1521R, LBV1521RBP, LBV1521BP, LBV1521 SERIES Quick Start Manual

FOR SUPPORT AND INFORMATION,

VISIT WWW.LOREXTECHNOLOGY.COM

Product Information

User Manuals

Quick Start Guides

Specification Sheets

Software Upgrades

Firmware Upgrades

Copyright © 2015 Lorex Corporation
As our products are subject to continuous improvement, Lorex reserves the right to modify product
design, specifications and prices, without notice and without incurring any obligation. E&OE

HD WEATHERPROOF

NIGHT VISION SECURITY CAMERA

Quick Start Guide

English Version 2.0

LBV1521 SERIES

153mm / 6.0”

70mm / 2.7”

Dimensions

70mm / 2.7”

Contents

• IR Night Vision Camera*

• Mounting Kit*

• 60ft BNC / Power Extension Cable*

• Power Adapter**

WARNING - A REGULATED power supply is REQUIRED for use with this

camera. Use of a non-regulated, non-conforming power supply can damage
this product and voids the warranty.

Warning/Caution

• Read this guide carefully and keep it for future reference.

• Follow all instructions for safe use of the product and handle with care.

• Use the cameras within given temperature, humidity and voltage levels
noted in ‘Camera Specifications’.

• Do not disassemble the cameras.

• Do not point the cameras directly towards the sun or a source of intense
light.

• Use only the supplied regulated power supply. Use of a non-regulated,
non-conforming power supply can damage this product and voids the
warranty.

• Periodic cleaning may be required. Use a damp cloth only. Do not use
harsh cleaners or aerosol cleaners.

Installation Tips

• Point the cameras where there is the least amount of obstructions (i.e. tree
branches).

• Install the cameras where they are difficult for vandals to reach.

• Secure cabling so that it is not exposed or easily cut.

• Cameras rated for outdoor use. Installation in a sheltered location
recommended.

* Per camera in multi-camera packs.
** An “8-in-1” Power Adapter that provides power to eight cameras or individual power adapters
may be provided, depending on product configuration.

Camera Specifications

Image Sensor* 1/2.9” 720p Megapixel Image Sensor

Video Format NTSC (LBV1521B / LBV1521R)

PAL (LBV1521BP / LBV1521RBP)

Effective Pixels H: 1280 V: 720

Resolution 720p

Scan System Progressive

Sync System Internal

S / N Ratio 50dB (AGC Off)

Iris AES

AES Shutter Speed 1/60 (1/50) ~ 1/100,000 Sec.

Min. Illumination 0.1 Lux without IR LED

0 Lux with IR LED

Video Output Lorex Analog HD

Lens / Lens Type 3.6mm F1.9 / Fixed

FOV (Diagonal) 90°

Termination BNC Type

IR LED Qty. / Type 12 pieces / 850nm

Night Vision Range** 130ft (40m) / 90ft (28m)

Power Requirement 12V DC ±10%

Power Consumption Max. 180mA (w / IR)

Operating Temp. Range –22° ~ 122°F / –30° ~ 50°C

Operating Humidity Range < 95% RH

Indoor/Outdoor*** Both (IP66)

Weight (including stand) 0.3lbs / 0.1kg

* 1080p cameras are compatible with 1080p HD DVR recorders. 720p cameras are
compatible with 720p & 1080p HD DVR recorders.
** Stated IR illumination range is based on ideal conditions in typical outdoor night
time ambient lighting and in total darkness. Actual range and image clarity depends on
installation location, viewing area and light reflection / absorption level of object.
*** Not intended for submersion in water. Installation in a sheltered location recommended.

Features

• High definition 720p image sensor delivers double the resolution of
960H*

• Crystal clear video with outstanding detail, day or night

• Infrared cut filter ensures accurate color representation

• Night vision range up to 130ft (40m) in ambient lighting & 90ft
(28m) in total darkness**

• Close up recognition in the dark with SmartIR

• Anti-glare feature ensures clear images under strong lighting
conditions

• ClearNight imaging for superior low light performance, improving
recording efficiency

• Split glass design minimizes IR reflection

• Weatherproof for outdoor & indoor installation (IP66 Rated)***

• Extreme temperature performance (–22°F ~ 122°F / –30°C ~ 50°C)

• Wide angle 90° field of view

• Vandal resistant design with cable pass-through bracket

• Lightweight and durable polycarbonate housing

• Removable camera base and integrated cable for flexible installation

• Versatile ceiling or wall mounting options

• Residential and business friendly compact design

Disclaimers:

* 1080p cameras are compatible with 1080p HD DVR recorders. 720p cameras are compatible
with 720p & 1080p HD DVR recorders.
** Stated IR illumination range is based on ideal conditions in typical outdoor night time ambient
lighting and in total darkness. Actual range and image clarity depends on installation location,
viewing area and light reflection / absorption level of object.
*** Not intended for submersion in water. Installation in a sheltered location recommended.

Setup Diagram

Multi-Camera Power Adapter

Before installing the cameras:

• Decide whether to run the cables
through the wall / ceiling (drilling
required) or along the wall / ceiling.

• If you run the cables along the wall
/ ceiling, you must run the cable
through the cable notch on the base.
This will keep the camera base flush
to the surface when mounted.

To install the cameras:

1. Set the camera in the desired mounting position and

mark holes for screws through the camera base.

2. Drill the holes, then feed the cable through the

mounting surface or cable notch.
NOTE: Insert the included drywall anchors if
installing the camera in drywall.

3. Mount the camera stand to the surface using the

provided screws. Make sure all screws are fastened
tightly.

Installing the Cameras Cable Extension Options

Extend the cable run for your camera depending on the cable type
used. Additional extension cables sold separately. See table below:

Option Cable Type Max Cable Run

Distance

1 Lorex model MCBL-60BNCU BNC Cable

(included with camera)

60ft / 18m

2 ‘RG59’ or ‘Coax’ or ‘Coaxial BNC’

Siamese (Video and Power)

300ft / 92m

3 ‘RG59’ or ‘Coax’ or ‘Coaxial BNC’

(Video Only

2)

800ft / 242m

Notes:

1. The extension cable must be a single stretch of cable between the DVR
and camera. You cannot connect multiple extension cables to each other.

2. For cable runs above 300ft / 92m (option 3), you must connect the
power adapter directly to the camera, rather than at the end of the
extension cable.

3. Indicators that your cable run may be too long:

• Video is permanently black & white (even during day time)

• Video is unclear, soft, or distorted

4. For more information on extension cables, visit

www.lorextechnology.com/support.

Problem Solution

No picture / signal • 1080p cameras are compatible with 1080p

HD DVR recorders. 720p cameras are
compatible with 720p & 1080p HD DVR
recorders.

• Ensure your TV is on the correct input channel.
Common terms of an input channel: INPUT, AV
CHANNEL, LINE1, LINE2, AUX.

• Ensure your DVR is properly connected to your
TV / Monitor.

• Ensure connections are properly connected.

• Ensure the camera power supply is plugged in.

Picture is too bright • Ensure your camera isn’t pointed directly at a

source of light (e.g. sun or spot light).

• Move your camera to a different location.

Picture is too dark • Check the brightness and contrast settings of

the DVR or monitor.

Night vision is not
working

• The night vision activates when light levels
drop. The area may have too much light.

Picture is not clear • Check the camera lens for dirt, dust,

spiderwebs. Clean the lens with a soft, clean
cloth.

• Make sure that the cable run is within the
limitations specified in the section ‘Cable
Extension Options’.

Bright spot in video
when viewing camera
at night

• Night vision reflects when pointing a camera
at a window. Move the camera to a different
location.

Troubleshooting

To Camera:

To DVR:

Male Power

BNC

1. Connect the BNC and
power connectors to the
camera.

Female Power

2. Connect the BNC connector to
the video input of your DVR.

3. Connect the power connectors
to the 8-in-1 power adapter. OR
Connect each camera to an
individual power adapter.

Connecting the Cameras

Cable Notch

4. Set the position and angle of the camera.

An multi-camera power adapter that provides power to multiple
cameras may be provided, depending on product configuration.
Connect multiple cameras to the power splitter cable.

ATTENTION - Test each camera prior to selecting a permanent mounting

location by temporarily connecting the camera(s) and cables to the DVR.

B

C

B) Loosen lower screw with a philips
head screwdriver (not included) to
adjust the camera’s vertical position.

C) Loosen upper screw with
philips head screwdriver (not
included) to rotate the camera
housing.

A

A) Turn the adjustment ring to tighten / loosen the stand
connection. Adjust the camera’s horizontal position.

ATTENTION - This camera includes an Auto Mechanical IR Cut Filter. When

the camera changes between Day/Night viewing modes, an audible clicking
noise may be heard from the camera. This clicking is normal, and indicates
that the camera filter is working.

HD DVR

LBV1521_SERIES_TRIFOLDQSG_EN_R2