Lorex LAE221 SERIES Quick Start Manual

Resources

LAE221_QSG_EN_R1

1080p HD Dome Security Camera

Copyright © 2018 Lorex Corporation
As our products are subject to continuous improvement, Lorex reserves
the right to modify product design, specifications and prices, without
notice and without incurring any obligation. E&OE. All rights reserved.

Quick Start Guide

English Version 1.0

LAE221 SERIES

• 1080p HD Dome Security Camera

• Mounting Kit*

• BNC / Power Extension Cable*

• Power Adapter**

* Per camera in multi-camera packs.
** A multi-camera power adapter that provides power to multiple
cameras or individual power adapters may be provided depending on
product configuration.

Package Contents

ATTENTION:

A REGULATED UL / CSA APPROVED power supply is REQUIRED for use
with this camera (included). Use of a non-regulated, non-conforming
power supply can damage this product and voids the warranty.

• Read this guide carefully and keep it for future reference.

• Follow all instructions for safe use of the product and handle with
care.

• Use the camera within given temperature, humidity and voltage levels
noted in the camera’s specifications.

• Do not disassemble the camera.

• Do not point the camera directly towards the sun or a source of
intense light.

• Use only the supplied regulated power supply provided with the
product. Use of a non-regulated, non-conforming power supply can
damage the product and void the warranty.

• Periodic cleaning may be required. Use a damp cloth only. Do not use
any harsh, chemical-based cleaners.

• The supplied cable is rated for surface mounting only. Cables for
in-wall and floor-to-floor installations are sold separately (CMR type).
These and other cables are available at lorex.com.

Safety Precautions

• Point the camera where there is the least amount of obstructions

(i.e., tree branches).

• Install the camera where vandals cannot easily reach.

• Secure cabling so that it is not exposed or easily cut.

• This camera is rated for outdoor use. Installation in a sheltered

location is recommended.

Installation Tips

• For a full list of compatible recorders, visit lorex.com/compatibility.

• Not intended for submersion in water. Installation in a sheltered

location recommended.

Disclaimers

Need Help?

Visit us online for up-to-date software and

complete instruction manuals

Click on the Downloads tab

4

Visit lorex.com

Search for the model number

of your product

Click on your product in the

search results

3

2

1

www.lorex.com

Dimensions

3.9” /

100mm

3.9” / 100mm

3.5” /

90mm

Connecting the Cameras

Individual Power Adapter* Multi-Camera Power Adapter*

Connecting the Cameras

* Images for representation only

Mounting Surface

Ball Camera

Dome Cover

Drywall Anchors (×3)

Mounting

Screws (×3)

Camera Base

Installing the Camera

Extend the cable run for your camera depending on the cable type used.
Additional extension cables sold separately. See table below:

Connect the male power head
and the BNC connector to the
camera.

Connect the BNC connector
to a video input on your DVR.

Connecting the Camera

LAE221_QSG_EN_R1

Power Adapter Types

A multi-camera power adapter that provides power to multiple cameras
or individual power adapters may be provided, depending on product
configuration.

Problem Solution

No picture / signal

• The cameras are only compatible with
certain Lorex HD DVRs. For the full list of
compatible recorders, visit

lorex.com/compatibility.

• Ensure your TV or monitor is on the
correct input channel. Common terms
for input channels: INPUT, AV CHANNEL,
LINE1, LINE2, AUX.

• Ensure your DVR is properly connected
to your TV or monitor.

• Ensure connections are properly
connected.

• Ensure the camera power supply is
plugged in.

Picture is too bright • Ensure your camera isn’t pointed directly

at a source of light (e.g., sun or spot
light).

• Check the brightness settings of the
DVR and monitor.

• Move your camera to a different location.

Picture is too dark • Check the brightness and contrast

settings of the DVR and monitor.

Night vision is not
working

• The night vision activates when light
levels drop. The area may have too much
light.

Picture is not clear • Check the camera lens for dirt, dust,

spiderwebs. Clean the lens with a soft,
clean cloth.

• Make sure that the cable run is within
the limitations specified in the section
‘Cable Extension Options’.

Bright spot in video
when viewing camera
at night

• Night vision reflects when pointing a
camera through a window. Move the
camera to a different location.

Troubleshooting

ATTENTION:

• Test your camera prior to selecting a permanent mounting location by
temporarily connecting the camera and cable to your DVR.

• The camera base comes detached from the dome cover, follow the
installation steps below before attaching the dome cover to the
camera base.

Before Installing the Camera

• Decide whether to run the cables through the
wall / ceiling (drilling required) or along the wall
/ ceiling.

• If you run the cables along the wall / ceiling,
you must run the cable through the cable
notch on the base. This will keep the camera
base flush to the surface when mounted.

ATTENTION:

This camera includes an Auto Mechanical IR Cut Filter. When the camera
changes between Day/Night viewing modes, an audible clicking noise may
be heard from the camera. This clicking is normal, and indicates that the
camera filter is working.

Connect the female power
head to the included power
adapter.

Camera

DVR

Male Power Female Power

Setup Diagram

BNC Video

12V DC PowerCamera

Extension Cable

Power Adapter

HD DVR

Cable Extension Options

Option Cable Type

Max Cable Run

Distance

1

Lorex model MCBL-60BNC4 BNC Cable
(included with camera)

60ft (18m)

2

‘RG59’ or ‘Coax’ or ‘Coaxial BNC’ Siamese
(Video and Power)

200ft (60m)

3

‘RG59’ or ‘Coax’ or ‘Coaxial BNC’ (Video
Only)

2

500ft (150m)

Notes:

1. The extension cable must be a single stretch of cable between the
DVR and camera. You cannot connect multiple extension cables to
each other.

2. For cable runs above 200ft (60m), you must connect the power
adapter directly to the camera, rather than at the end of the
extension cable.

3. Baluns are not supported for LAE221.

4. Indicators that your cable run may be too long:

• Video is permanently black & white (even during day time)

• Video is unclear, soft, or distorted

5. For more information on extension cables, visit lorex.com.

Cable Notch

To install your camera:

1. Set the camera base in the desired mounting position and mark
holes for screws through the camera base.

2. Drill the holes. Insert the included drywall anchors if you are
mounting the camera onto drywall.

3. Feed the cable through the camera base. If you are running the
cables against a wall or ceiling, make sure to pass the cable
through the cable notch as shown above.

4. Connect the cables as shown in the section ‘Connecting the
Camera’.

5. Mount the camera base to the mounting surface using the included
screws and optional drywall anchors.

6. Place the dome cover over the ball camera and angle the ball
camera to the desired position.

7. While holding the ball camera in place, firmly push the dome cover
onto the camera base until it clicks in place.

8. If necessary, reposition the ball camera by firmly pushing the ball
camera to the desired angle.

NOTE: If necessary, use a flat head screwdriver to detach the dome

cover from the camera base.