* Minimum System Requirement: Windows XP, Pentium
IV, 256MB Ram (512MB Recommended), 200MB Storage,
Internet, DSL or Cable Modem
STEP 3
TimeHardware
60 Minutes
* Installation time may vary based
on application
REMOTE CONTROL:
Computer &
Router*
* Minimum System Requirement: Windows XP, Pentium IV,
256MB Ram (512MB Recommended), 200MB Storage, Internet,
DSL or Cable Modem
RECOMMENDED
FOR USE FROM A
DISTANCE
Skills - Advanced
Plug & Play connectors, On
screen set up
Plug & Play connectors,
On screen set up
Basic Computer Skills,
Router Port Forwarding
LEFT BUTTON
• Double click in
viewing mode to
display camera in
full screen.
Check Pages
L19LD1600 Series Quick Set-Up Guide R1
9-10
ATTENTION:
Broadband Router
and Computers are
required for local and
remote monitoring
(not included).
RIGHT BUTTON
• Click to open/exit
the Mouse MENU
in Viewing Mode.
SCROLL WHEEL
• Used to increase
values in the
MENU mode.
ATTENTION:
*Number of channels,
cameras and hard drive
capacity may var y by
model. Check your
package for specific
content information.
1. MENU
2. NUMBER KEYPAD
3. SEQUENCE MODE
4. FREEZE
5. 4S BUTTON
6. 9S BUTTON
7. NAVIGATION CONTROLS / ENTER
8. REC BUTTON
9. NAVIGATION CONTROLS
10. SEARCH BUTTON
11. DISPLAY MODE
12. P/T MODE
13. AUDIO CHANNEL SELECT
14. PIP MODE
15. 16S
16. STOP
17. NEXT
18. VOL +/-
INSTRUCTIONS:
For detailed setup
information, please
refer to your User’s
manual.
SOFTWARE
REQUIREMENTS:
For Lorex Client Software
requirements, please refer
to Lorex Client Manual.
Page 3
STEP 1 - SET UP YOUR MONITOR FIRST
CONNECT CAMERAS TO THE SYSTEM:
1
2
Connect the first camera to the CH1 input. Follow the same steps to connect the
additional cameras.
1. Connect the Female BNC end of the supplied 60’ extension cable to the camera.
Connect the male Power end of the extension cable to the camera.
2. Connect the Female end of the supplied 60’ extension cable to an open BNC
camera input on the back of the System. Connect the female Power end of the
extension cable to one of end of the power adaptor.
CONNECT ETHERNET CABLE:
Connect one end of the ethernet cable to one of the router’s (not included) LAN
PORTS and the other end to Monitor’s Network Port located at the bottom of the
monitor. See picture below showing a generic LAN/WAN connection.
IMPORTANT NO TE: The ends of the extensi on cable are N OT
the same - o ne end has a Male power por t, and the oth er has
a Female pow er port. Befo re permanently running the C amera
Extension Ca ble, make sur e that the cab le has been or iented
between the Camera and th e unit correct ly.
3
3
4
LAN (LOCAL AREA NETWORK)
BACK OF THE ROUTER SHOWN
TO YOUR COMPUTER
WAN (WIDE
AREA NETWORK)
TO YOUR MONITOR
CONNECT THE MOUSE:
Connect the the Mouse included with your system to the PS2 port of the monitor.
MOUSE CONTROL
AVAILABLE
CONNECT POWER CABLE:
Connect one end of
the Power adaptor
to the monitor, the
other end to an
electrical outlet.
Note: Turn ON
the Master Power
Switch at the back
of the system.
MASTER POWER BUTTON
Your system will
perform a System
Check once the
MASTER power
button at the back
of the system is
turned ON.
5
L19LD1600 Series Quick Set-up Guide R1
SET THE TIME AND DATE:
1. Press the MENU button from the Front Panel of the Monitor (or Remote Control), or use the
Mouse and Click the Menu Icon .
2. DVR LOG IN screen appears. Press ENTER.
Note: USER ID BY DEFAULT IS ADMIN. Password is numeric and not necessarily needed for
initial MENU setup. Press ENTER to enter the MAIN MENU.
3. On the MENU screen select CONFIGURATION and click ENTER.
4. Select TIME AND DATE SETUP to set your local time
5. Press MENU button repeatedly to exit this screen.
Congratulations! You have completed Step 1 successfully. You can now view, record
and playback images on your monitor.
After you see
camera images
on your monitor
screen, remove
the protective film
from camera(s)
and monitor
screen.
Make sure that
the Date and Time
are set prior to
recording.
Page 4
4
STEP 2 - SET UP LOCAL VIEWING ON YOUR PC
RETRIEVE SYSTEM INFORMATION:
1
*YOUR SYSTEM MUST BE CONNECTED TO
A ROUTER PRIOR TO POWERING IT ON.
IP ADDRESS: . . .
MAC ADDRESS:
(Required for DDNS registration)
1. Access the Main Menu Setup screens, and navigate to the SYSTEM
MENU - EXTERNAL DEVICE - TCP/IP SETUP - IP CONFIG SETUP option.
2. Record the MAC Address of your system. This information is NECESSARY
for the DDNS Setup process.
3. Confirm that the DHCP MODE is set to AUTOMATIC. This will allow your
system to lease an IP ADDRESS from your router. If the system is not set to
AUTOMATIC, change the setting in the DHCP SETUP menu and click
DETECT IP.
4. The IP PORT is 50000 by default.
RECORD THE IP AND MAC ADDRESSES IN THE SECTION BELOW:
NOTE: The system will lease networking
information from your Router. If you wish
to set your information manually, then
set the DHCP MODE to MANUAL. Please
consult your Hardware Manual for further
Menu options.
2
3
4
1
INSTALL SOFTWARE:
(on your local computer)
Insert the Lorex Software CD into your local computer’s CD ROM
drive and proceed with the installation.
LOREX INTERNET REMOTE SOFTWARE (IRS):
(on your local computer)
Follow the installation screens to complete Lorex Internet Remote
(ISA) Software installation.
2345
LOREX INTERNET REMOTE SOFTWARE (IRS):
(on your local computer)
Close the CD Menu Screen. A Lorex Internet Remote Software (IRS) icon
will appear on your desktop.
L19LD1600 Series Quick Set-Up Guide R1
RUN THE LOREX CLIENT 5.0 SOFTWARE:
(on your local computer)
Double-click the Lorex Internet Remote Software (IRS) icon on your desktop to
run the program. From the main screen, click LOREX CLIENT 5.0
Page 5
STEP 2 - SET UP LOCAL VIEWING ON YOUR PC (CONTINUED)
SET-UP:
5
6
(on your local computer for local viewing)
Click the SETUP button from the Lorex Client 5.0 Software Screen.
LOREX CLIENT 5.0 REMOTE ACCESS SETUP
(on your local computer for local viewing):
1. Select the IP/PORT Tab.
MANUAL (for local viewing).
2. Click
3. NAME: Enter a name for the system. E.g. Office
4. ADDRESS: Add the IP address recorded earlier at Step 2 - 1
5. PORT: By default is set to 50000
6. USER ID: By default is admin
7. PASSWORD: Leave it blank
8. Press SAVE to add the system name you have created.
5
7
VIEW CAMERAS LOCALLY:
(on your local computer for local viewing):
From the Lorex Client 5.0 software - local configuration screen (as shown in the picture), press the Connect button to connect to Local Live site to view your cameras.
Congratulations! You have completed Step 2 successfully.
You can now view and playback images on your local
computer over the Local Area Network (LAN).
L19LD1600 Series Quick Set-up Guide R1
Page 6
6
STEP 3 - SET UP INTERNET REMOTE SECURITY MONITORING
PORT FORWARD YOUR ROUTER:
1
Port forward your router first before proceeding with the set-up (port
50000).
All routers are different. To port forward your router, please refer to
your router’s user manual.
A router configuration guide is available on your Lorex Client Software
CD and also on www.lorexcctv.com/support in the Consumer’s Guide
Section.
DDNS SET-UP:
2
Open your web browser (Internet Explorer by default) and enter
http://www.lorexddns.com in the address bar.
3
4
DDNS REGISTRATION:
Select the REGISTER option from the list on the left side of the
screen.
CREATE NEW USER INFORMATION:
Complete the NEW USER fields with your personal information:
• USER NAME - Enter the desired User Name for connection.
• USER PASSWORD / CONFIRM PASSWORD - Enter and confirm a
password for the connection.
NOTE: The username and password provided are NOT the same as the ADMIN/
PASSWORD on the System. These credentials are used for your
specific connection to your unit.
• EMAIL - Enter your Email Address.
L19LD1600 Series Quick Set-Up Guide R1
Press the OK button to save the settings.
A Successful Registration window will appear.
Page 7
STEP 3 - SET UP INTERNET REMOTE SECURITY MONITORING (CONTINUED)
LOGIN:
5
Once the account has been created, you will need to login using your
credentials (as set in step 4).
Once the Username and Password have been entered, press the LOG IN button to
access the Configuration Menu.
7
6
ADD DVR:
Select the ADD DVR link from the top of the page.
The DVR Setup screen will appear:
• DVR NAME - Enter the desired name for your System (e.g.
MyBusiness) to a maximum of 20 numbers and letters.
• MAC ADDRESS - Enter the MAC Address from the system (as retrieved
from the System Information in the IP & MAC Address section on page 4). The
MAC ADDRESS IS 12 CHARACTERS WITH NO SPACES OR DASHES.
• Select the Dual Codec (19” 16CH LCD Combo) option
• IP ADDRESS & PORT
will access your unit based on the MAC Address.
Press OK to save the settings. Once the settings are saved, the configuration will
appear in your DDNS List. This configuration can now be added to the System.
- This information can be left blank - the DDNS Service
7
L19LD1600 Series Quick Set-up Guide R1
ENTER DDNS SET-UP ON YOUR MONITOR:
Access the Main Menu Setup screens, and navigate to the SYSTEM MENU
STEP 3 - SET UP INTERNET REMOTE SECURITY MONITORING (CONTINUED)
8
9
ENABLE DDNS SETTINGS:
• Set the DDNS ENABLE to ON
• Click on REGISTER to connect to the DDNS server and register the system information
The following will automatically complete after clicking the Register option:
• DNS SERVER - Confirm that the IP address is set to 202.133.244.128
• INTERVAL - Set an interval for the DVR to auto-update its IP address to DDNS server (D-
days / H- hours / M- minutes). Default : D-00 H-00 M-20, update every 20 minutes.
• REGISTER - Connect to the DDNS server and register the DVR information to DDNS database
• DNS STATUS - Indicates the current status of DDNS connection.
• IP ADDRESS - Indicates the local IP address assigned by the router (the internal IP address of
your system).
• IP PORT - Indicates the current port number in the system (50000 by default).
• REMAIN TIME - Indicates the remaining time until the System next updates the IP address with
the DDNS Service.
• LAST REGISTRATION DATE - Indicates the last successful date and time that an update
occurred. To save the changes and exit , click on the MENU button.
LOREX CLIENT REMOTE ACCESS SETUP:
The remote connection information needs to be added to the Lorex Client software to allow
for a remote connection (using DDNS).
1. Load the Lorex Client Software. Click on SETUP to add the configuration.
2. The Remote Viewer Setup window will load to the
settings will be greyed out) and click the DDNS tab.
MyBusiness
IP/PORT Tab. Click on the DDNS button (all
10
3. On the DDNS tab, enter your
• USER NAME - Enter the user name you configured on the DDNS Website (default is set to
GROUP as an example, and can be deleted).
• DVR NAME - Enter the DVR name you configured on the DDNS Website.
• USER ID - Enter the DVR user ID (admin by default)
• PASSWORD - By default is blank
4. Click the
5. Click on the
7. Press
SAVE Button to accept the settings.
GET IP button to retrieve the IP Address and Port Number from the DDNS Server.
OK to save the settings, and close the configuration window.
DDNS Information as follows:
VIEW CAMERAS REMOTELY:
Click the CONNECT button to remotely access your System.
Remote Viewing with Internet Explorer: Video from the System can be viewed using the Internet Explorer
interface (for remote viewing and backup). All Remote functionality through the Internet Explorer
interface is provided at http://www.lorexddns.com. For more information, please refer to Lorex Client
Software Manual.
Congratulations! You have completed Step 3 successfully. You can now view and
playback images on your remote computer over the Internet.
L19LD1600 Series Quick Set-Up Guide R1
Page 9
RECOMMENDED TIPS
LOCATE MONITOR CONNECTIONS:
Tilt the monitor UP to loacte your
monitor’s connections.
FUNCTION ICONS - AVAILABE FOR USE ONLY THROUGH A MOUSE
9
Right click to open mouse
control interface.
The corresponding functions
for mouse buttons please
refer to the following chart.
L19LD1600 Series Quick Set-up Guide R1
Page 10
10
RECOMMENDED TIPS (CONTINUED)
HDD INSTALLATION:
The System comes with a pre-installed Hard Drive in the
removable hard drive bay. The system can support up to 2 hard
drives ( max 750GB each ), one in the removable bay and one
internally.
NOTE: Make sure that the System is OFF and the power cable has
been disconnected before changing the Hard Drive. For detailed
instructions, check your user’s manual included with the system.
Please refer to the system’s user manual for HDD formatting and installation.
TIP ON CAMERA MOUNTING:
Note: Test the cameras prior to selecting a permanent mounting
location by temporarily connecting the Cameras and Cables to
your System.
TIP ON REMOTE VIEWING AND PLAYBACK:
NOTE: You must have an active high speed internet connection
to the System to be able to perform Remote viewing or playback.
Remote access is dependant on your connection speed, internet
traffic and other network factors - the speed is normally 1~2 FPS
(frames per second).
For faster remote viewing over the internet we recommend using
the H.264 Viewer (see page 11). H.264 compression provides
smaller file sizes resulting in a higher speed over the internet.
For faster playback, it is recommended to download previously
recorded video using the backup function and play it back using
Backup Player Software - refer to the user manual for details.
L19LD1600 Series Quick Set-Up Guide R1
Regardless of the network playback speed, video is being
recorded on your system in real time, and can be viewed when
you are at the system or through the backup player.
Page 11
LOREX INTERNET REMOTE SOFTWARE (IRS)
11
1
2
3
4
5
1. LOREX CLIENT 5.0
Remote monitoring software recommended for local area network (LAN) - View, Playback and Record.
2. LOREX BACKUP
Use this software to create a backup of your recorded data from a remote location.
3. LOREX PLAYER 5.0
Use this software to playback data that has been backed up either from the system using a USB
thumbdrive or from the backup software.
4. LOREX REMOTE SETUP
Use this software to configure the system remotely (e.g. change recording settings or schedules).
5. LOREX IRS SETUP
Setting up IRS is necessary in order to use the H.264 Viewer.
6. LOREX H.264 VIEWER
6
Remote monitoring software recommended for Internet Remote Monitoring. H.264 video compression
technology allows for efficient data transfer over the internet. You can view your system remotely while
consuming less bandwidth.
L19LD1600 Series Quick Set-up Guide R1
Page 12
12
product support
It’s all on the Web
www.lorexcctv.com
For detailed setup information, please refer to your User’s Manual. For
additional information about determining your IP address, configuring your router,
and port forwarding, please visit our website www.lorexcctv.com/support and
click Consumer Guides Section or view guides from the Lorex Client Software CD
included with your system.
Email Support: support@lorexcorp.com
Toll Free Technical Support - North America: 1-888-42 LOREX (1-888-425-6739)
Toll Free Technical Support - International (outside of North America): 00-800-425-6739-0
Lorex International Website - www.lorexinternational.com
L19LD1600 Series Quick Set-Up Guide R1
PRODUCT SUPPORT
Specification Sheet
User’s Manual
Lorex Client Software Manual
Quick Start Guide
Port forwarding Guide
Basics of Remote Video
Access Guide
QUICK SET-UP GUIDE
USER’S MANUAL
FAQ
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.