Lorex CVC6950 SERIES Quick Start Manual

QUICK START GUIDE

www.lorextechnology.com

Lorex Technologies Inc.
Copyright © 2010 Lorex Technologies Inc.
As our products are subject to continuous improvement, Lorex reserves the right to modify product
design, specifications and prices, without notice and without incurring any obligation. E&OE

Cable Extension Options

HIGH RESOLUTION
INDOOR/OUTDOOR

COLOR CAMERA

with Night Vision

Problem Solution

No Picture/Signal • Ensure your TV is on the correct input

channel. Common terms of an input channel:
INPUT, AV CHANNEL, LINE1, LINE2, AUX.

• If your camera is connected to a VCR/DVR,
ensure it is properly connected to your TV/
Monitor.

• Ensure connections are properly connected.

• Ensure all the camera power supply is
plugged in.

Picture is too bright • Ensure your camera isn’t pointed directly at a

source of light (e.g sun or spot light).

• Slide the sunshade (bullet cameras only)
forward to bloc k excess light.

• Move your camera to a different location.

Picture is too dark • If using during the day, the camera may not

be getting enough light. Slide the sunshade
backwards to let in more light. Check the
brightness and contrast settings of the device
your camera connects to (TV/Monitor/DVR).

Night Vision is not
working

• The night vision activates when light levels
drop. The area may have too much light.

Picture is not clear • Check the camera lens for dirt, dust,

spiderwebs. Clean the lens with a soft, clean
cloth.

• Make sure that the cable run is within the
limitations specified in the section ' Cable
Extension Options'

Bright spot in video
when viewing camera
at night

• Night vision reflects when pointing a camera
to a window. Move the camera to a different
location.

BNC connection does
not connect to my TV

• Use a BNC to RCA adapter at the end of the
extension cable.

Troubleshooting

Option Cable Type

1

Regular BNC
(supplied with
camera)

180ft / 55m 3

2

'RG59' or 'Coax'
or ' Coaxial'
BNC (sold sepa­rately)

300ft / 92m 5

3

Lorex Universal
Cable
(sold separately)

300ft / 92m 3

Max. Cable
Run Distance

Max. # of
Extensions

MODEL: CVC6950 SERIES

English Version 1.0

Camera Specifications

Notes:

1. For optimal performance, consider using option 2 or 3. Preference for using
the same cable type for the entire distance.

2. Cable run recommendation based on typical camera power consu mption (up
to 500mA). For specialty cameras with higher current consumption,
maximum cable run may be reduced. Consider providing power to the camera
at the camera side rather then at the end of the extension cable.

3. Indicators that your cable run may be too long:

• Video is permanently Black & White (even during day time)

• Video is distorted

Extend the cable run for your camera up to 300ft or more
depending on the cable type used. See table below:

Image Sensor 1/4” Advanced Color

Lens / Lens Mount

Video Format / Pixels

Horizontal Resolution

Minimum Illumination

Termination

IR / Night Vision Range

FOV (diagonal)

S/N Ratio

Sync. & Scan. Systems

Video Output

Power Consumption

NTSC: 656(H) x 492 (V)

480 TVL

0.6 LUX @ F1.2 (IR off)
0 LUX (IR LEDs on)

Video: BNC Female
Power: Barrel Female

18 IR LEDs/850nm/50’ (15m)

50 Degrees

> 48dB

Internal; 2:1 Interlace

Comp. 1.0 Vpp @ 75ohm

250 mA or 3W max

Operating Temp.

Dimensions
LxWxH
(with sunshade)

14°F ~ 122°F
(-10°C ~ 50°C)

2.6" x 4.2" x 5.2"
66 mm x 107 mm x 132 mm

5.1 mm F2.8/ Fixed

Iris & Shutter Speed AES; 1/60 ~ 1/50,000 sec.

Power Requirement 12V DC ±10%

Weight (with stand) 0.6 lbs. / 0.26 kg

Product Information

User Manuals

Quick Start Guides

Specification Sheets

Software Upgrades

Firmware Upgrades

www.lorextechnology.com

IT’S ALL ON THE WEB!

2.6"/ 66mm

5.2"/
132mm

4.2"/107mm

To install the camera:

1. Mount the camera stand to the desired mounting surface.

2. Attach the camera to the stand at either of the two
connection points at the back of the camera.

3. Connect the extension cable to the camera:

ATTENTION - Test all connections and ensure the camera is working

correctly prior to permanent installation by temporarily connecting the
camera(s) and cable(s) to the viewing/recording solution.

Wall Mount

Ceiling Mount

Table Mount

Use the stand for ceiling, table, or wall mounting.

Connect the BNC
and power
connectors to the
camera.

Connect the BNC
connector to the video
input of the monitor/DVR,
and connect the included
power connector to a
power adapter.

Male power connector

Female power connector

BNC Connector

To Camera:

To Monitor/ DVR:

Contents

Features

• High resolution AIS (Advanced Image Sensor) produces
sharp and clear video at 480 TV lines of resolution

• Lorex Pure Flat™ lens eliminates image curving for an
undistorted view

• Anti-glare technology ensures clear images even in
strong lighting situations

• Exclusive built-in auto-mechanical infrared filter
achieves accurate color reproduction in varying lighting
conditions

• Advanced day/night mode - picture automatically
switches to B&W delivering better clarity in low light
conditions

* Model CVC6950PK4 is a 4-pack that includes four of the listed items.
** A "4-in-1" Power Adapter (provides power to four cameras) may be substituted
for four individual power adapters, depending on product configuration.

• Indoor / Outdoor Color Camera with Night Vision

• Mounting Bracket / Stand*

• 60 ft. BNC/Power Extension Cable*

• AC Power Adapter**

Installation Tips

• Point the camera where there is the least amount of
obstructions (i.e. tree branches).

• Install the camera in a location that is difficult for
vandals to reach.

• Secure cabling so that it is not exposed or easily cut.

• Connect your system and cameras to a back-up power
supply. This ensures the system continues to record
during power outtages.

Installing The Camera

Warning / Caution Statements

1. Read this guide carefully and keep it for future reference.

2. Follow all instructions for safe use of the product.

3. Use the camera within given temperature, humidity and voltage levels noted

in Camera Specifications.

4. Do not disassemble the camera.

5. Do not point the camera directly towards the sun or a source of intense light.

6. Use only the supplied regulated power supply. Use of a non-regulated, non-

conforming power supply can damage this product and voids the warranty.

7. The supplied extension cable is rated for surface mounting only.

Cables for in-wall / floor-to-floor installations are sold separately.

Setup Diagram

ATTENTION: This camera includes an Auto Mechanical

IR Cut Filter. When the camera changes between Day/
Night viewing modes, an audible clicking noise may be
heard from the camera. This clicking is normal, and
indicates that the camera filter is working.

WARNING - A REGULATED UL/CSA APPROVED power supply is REQUIRED

for use with this camera. Use of a non-regulated, non-conforming power
supply can damage this product and will void the warranty.

4. Connect the BNC end of the Extension Cable to the
DVR / Observation System or to a TV/VCR.

NOTE: Connect a BNC-to-RCA Adapter (optional,
Lorex model # BNCB) as needed to allow for proper
connectivity.

5. Connect the A/C Power Adapter to the 60ft
Extension cable (Black connector). Plug the Power
adapter to a wall outlet.

Connect the BNC cable to a DVR, CCTV, monitor or TV.

AC Power Adapter

4-in-1 Power Adapter
(optional)

Connect an AC power adapter.

Connecting The Camera