Lorex CVC6945PK4 Quick Start Manual

FOR SUPPORT AND INFORMATION,

VISIT WWW.LOREXTECHNOLOGY.COM

Product Information

User Manuals

Quick Start Guides

Specification Sheets

Software Upgrades

Firmware Upgrades

Contents

• IR Night Vision Camera*

• Mounting Kit / Allen Key*

• 60ft BNC / Power Extension Cable*

• Power Adapter**

• BNC-to-RCA Adapter***

Copyright © 2012 Lorex Technologies Inc.
As our products are subject to continuous improvement, Lorex reserves the right to modify product
design, specifications and prices, without notice and without incurring any obligation. E&OE

Camera Specifications

Image Sensor 1/4” Color Image Sensor

Video Format NTSC

Effective Pixels H: 668 V: 512

Resolution 480 TV Lines

Scan System 2:1 Interlace

Sync System Internal

S / N Ratio 48dB (AGC Off)

Iris AES

AES Shutter Speed 1/60 ~ 1/100,000 Sec.

Min. Illumination 0.1 Lux without IR LED

0 Lux with IR LED

Video Output Composite 1.0Vpp @ 75ohm

Lens / Lens Type 4.6mm F2.0 / Fixed

FOV (Diagonal) 57°

Termination BNC Type

IR LED Qty. / Type 30 pieces / 940nm

Night Vision Range* 50ft (15m) / 75ft (22m)

Power Requirement 12V DC ±10%

Power Consumption Max. 230mA (w / IR)

Operating Temp. Range 14° ~ 122°F / –10° ~ 50°C

Operating Humidity Range < 95% RH

Indoor/Outdoor** Both (IP66)

Weight (including stand) 0.7lbs / 0.3kg

* Stated IR illumination range is based on ideal conditions in total darkness and in typical outdoor
night time ambient lighting. Actual range and image clarity depends on installation location, viewing
area and light reflection / absorption level of object.
** Not intended for submersion in water. Installation in a sheltered location recommended.

WARNING - A REGULATED UL / CSA APPROVED power supply is

REQUIRED for use with this camera. Use of a non-regulated, non-conforming
power supply can damage this product and voids the warranty.

Features

• Advanced image sensor produces high resolution video
at 480 TV Lines of resolution

• Picture automatically switches to Black & White delivering
better clarity in low light conditions

• Clean & crisp night vision up to 50ft/15m away in total
darkness or up to 75ft/22m in ambient lighting*

• 30 Covert IR LED’s don’t glow red making it difficult to
detect the camera at night

• 4.6mm medium angle lens with a 57° diagonal of view
for improved object recognition

• Vandal resistant design with durable aluminum housing
and cable pass-through bracket

• IP66 weatherproof rated—ideal for outdoor and indoor
applications**

• Flexible mount offers wall and ceiling installation options

Disclaimers:

* Stated IR illumination range is based on ideal conditions in total darkness and in typical outdoor
night time ambient lighting. Actual range and image clarity depends on installation location,
viewing area and light reflection / absorption level of object.
** Not intended for submersion in water. Installation in a sheltered location recommended.

Warning/Caution

• Read this guide carefully and keep it for future reference

• Follow all instructions for safe use of the product and handle with care

• Use the camera within given temperature, humidity and voltage levels

noted in Camera Specifications

• Do not disassemble the camera

• Do not point the camera directly towards the sun or a source of intense

light

• Use only the supplied regulated power supply. Use of a non-regulated,
non-conforming power supply can damage this product and voids the
warranty

• Periodic cleaning may be required. Use a damp cloth only. Do not use
harsh cleaners or aerosol cleaners

• The supplied extension cable is rated for surface mounting only

• Cables for in-wall / floor-to-floor installations are sold separately

Installation Tips

• Point the camera where there is the least amount of obstructions (i.e. tree
branches)

• Install the camera in a location that is difficult for vandals to reach

• Secure cabling so that it is not exposed or easily cut

• Camera rated for outdoor use. Installation in a sheltered location

recommended

WEATHERPROOF

NIGHT VISION SECURITY CAMERA

Quick Start Guide

English Version 1.0

CVC6945 SERIES

151mm / 5.9”

66mm / 2.6”

Dimensions

*Model CVC6945PK4 is a 4-pack that includes four of the listed items.
** A “4-in-1” Power Adapter that provides power to four cameras or individual power adapters
may be provided, depending on product configuration.
*** Not included in multi-camera packs.

78mm / 3.1”

Setup Diagram

Power Adapter Types

Individual Power Adapter

4-in-1 Power Adapter

Connect a BNC-to-RCA Adapter (not included in multi-camera
packs, Lorex model # BNCB) to connect the extension cable to RCA
inputs (i.e. for a TV connection).

Before installing the camera:

• Decide whether to run
the cables through the
wall / ceiling (drilling
required) or along the
wall / ceiling.

• If you run the cables
along the wall /
ceiling, you must run
the cable through the
cable notch on the
base. This will keep the
camera base flush to the
wall / ceiling when mounted.

To install the camera:

1. Set the camera in the desired mounting
position and mark holes for the screws.

2. Drill the holes, then feed the cable through the
mounting surface or cable notch and mount
the camera stand to the surface using the
provided screws. Make sure all three screws
are fastened tightly at the connection points.

Installing the Camera Cable Extension Options

Extend the cable run for your camera up to 300ft or more
depending on the cable type used. See table below:

Option Cable Type Max Cable

Run Distance

Max # of

Extensions

1 Regular BNC

(supplied with camera)

180ft / 55m 3

2 ‘RG59’ or ‘Coax’ or

‘Coaxial BNC’
(sold separately)

300ft / 92m 5

3 Lorex Universal Cable

(sold separately)

300ft / 92m 3

Notes:

1. For optimal performance, consider using option 2 or 3. It is best to use
the same cable type for the entire distance.

2. Cable run recommendation based on typical camera power consumption
(up to 500mA). For specialty cameras with higher current consumption,
maximum cable run may be reduced. Consider providing power to the
camera at the camera side, rather than at the end of the extension cable.

3. Indicators that your cable run may be too long:

• Video is permanently black & white (even during day time)

• Video is distorted

ATTENTION - Test all connections and ensure the camera is working

correctly prior to permanent installation by temporarily connecting the
camera(s) and cable(s) to the viewing / recording solution.

Problem Solution

No picture / signal •Ensure your TV is on the correct input channel.

Common terms of an input channel: INPUT, AV
CHANNEL, LINE1, LINE2, AUX

•If your camera is connected to a VCR / DVR,
ensure it is properly connected to your TV /
Monitor

•Ensure connections are properly connected

•Ensure the camera power supply is plugged in

Picture is too bright •Ensure your camera isn’t pointed directly at a

source of light (e.g. sun or spot light)

•Slide the sunshade (bullet cameras featuring
adjustable sunshades only) forward to block
excess light

•Move your camera to a different location

Picture is too dark •If using during the day, the camera may not be

getting enough light. Slide the sunshade (bullet
cameras featuring adjustable sunshades only)
backwards to let in more light

•Check the brightness and contrast settings
of the device your camera connects to (TV /
Monitor / DVR)

Night vision is not
working

•The night vision activates when light levels
drop. The area may have too much light

Picture is not clear •Check the camera lens for dirt, dust,

spiderwebs. Clean the lens with a soft, clean
cloth

•Make sure that the cable run is within the
limitations specified in the section ‘Cable
Extension Options’

Bright spot in video
when viewing camera
at night

•Night vision reflects when pointing a camera
at a window. Move the camera to a different
location

BNC connection does
not connect to my TV

•Use a BNC to RCA adapter at the end of the
extension cable

Troubleshooting

To Camera:

To DVR:

Male Power

BNC

1. Connect the BNC and
power connectors to the
camera.

Female Power

2. Connect the BNC connector to
the video input of the DVR.

3. Connect the power connectors
to the 4-in-1 power adapter. OR
Connect each camera to an
individual power adapter. See
Power Adapter Types for details.

Connecting the Camera

Cable Notch

3. Set the position and angle of the camera using
the provided Allen key.

1) Turn the ring to tighten / loosen
the stand connection. Adjust the
camera’s horizontal position.

2) Loosen the screw and adjust
the camera’s vertical position.

1

2

Connecting the Camera to a TV

A “4-in-1” Power Adapter that provides power to four cameras or
individual power adapters may be provided, depending on product
configuration.

NOTE - This camera features night vision IR LED’s that are completely

invisible to the human eye when activated. The IR LED’s will not glow red
when night vision is on.