Page 1
2-in-1 phone holder and Qi wireless charger
Version 1.0
Page 2
Product Description
This product uses marine grade aluminum, high-strength stainless steel and high composite
plastic materials. Material lighter, higher strength, anti-aging and corrosion resistance is higher.
Variety of installation methods can be mounted to the right size and round tubular base on.
Supports all types of protective cover, clip used in conjunction.
The device can be easily mounted to the motorcycle, dirt bike, cruise cars, station wagons,
utility vehicles and off-road vehicles and other upper circular tube-like, using a base above.
Built-in 10W fast wireless charging module, the phone can be wirelessly charged on the surface.
Page 3
Bracket Assembly
1. Multifunction ball screw nut head and the multi-function clip on the fixed and confirmed firmly
fixed before use. As shown:
2. Clamp“Connecting rod”onto spherical ball of “fixed ball joint”
3. Multi-function clip and then fix the assembly to the other side of Connecting rod.
Page 4
Warning:
This section is casual version of the series frame, non-professional version. For road cycling
tour. Very bad road conditions are not suitable for cross-country road washboard roads. Thus
causing damage to the equipment the company does not undertake any responsibility!
For your safety during the ride, please loosen the fixing knob on “Connecting rod” before
adjusting the angle of the screen. Fasten the same knob “Connecting rod” after you adjust the
screen to the desirable angle. Here, we also kindly remind you not to adjust the screen during the
ride.
Bracket Mounting steps
1. As shown in Pic 1, secure mounting ball through the hole in the middle.
2. As shown in Pic 2，3，4, hook up four corners of the mobile.
3. In order not to block the lens of the mobile phone, please adjust the position of the
reinforcement net to the lower part of the mobile phone.
Page 5
Bracket Installation
Mounting hole diameter 10mm
1. Assemble it on the base of the reflective mirror. Remove the base from the reflective mirror.
Insert the ball head bolts with crooked into the mounting hole and remount the mirror. It’s
advisable to adjust the angles of the reflective mirror by increasing gaskets if the angle is not
right after the screw is tightened. As is shown in the picture:
2. Assemble other pieces if necessary, other pieces can be fixed on any position with screws
whose mounting holes go with the ball head bolts.
Power Connection
1. Connect the red wire to the ACC positive and the black to the GND.
2. Connect the USB receptacle line with the waterproof connector of the main line.
Item
Parameters
Input
9-28V
Output
5V 3A ,9V 2A
Cable length
2.5m
Note: Please carefully choose a suitable location for installation to ensure safety.
Page 6
Smart wireless charging cable
How to charge the phone quickly?
1. First of all, ensure that the mobile phone supports the fast charging function, the device will
adaptively output the corresponding charging power according to the mobile phone (such as 10
watts, 7.5 watts, 5 watts); if the mobile phone does not have a fast charging function, it can be
charged normally.
2. When charging, make sure that the phone is in closely bonded to the round part of the bracket
with the mark.
3. Please ensure that the thickness of the phone case is within 4MM, so that the wireless
charging function can be used normally.
4. If the indicator light flashes rapidly or goes out during charging, please check if the charging
part of the bracket is aligned with the wireless charging part of the mobile phone, or if there is
metal object between the wireless charging and the mobile phone holder.
Indicator description
1. Connect the wireless charging USB port to the smart management power cable, connect the
power cable to the motorcycle switch, and the white indicator light is always on for about 4
seconds for self-test.
2. When the device is in the standby state, the white indicator flashes once every 3 seconds.
3. When the device charges the phone, the white indicator light is always on.
4. During the charging process, if the white indicator light flashes once per second, indicating
that the power output power is low, please adjust the position of the mobile phone in time, and
align the wireless charging induction coil of the mobile phone with the wireless charging position
of the bracket.
Page 7
SPECIFICATION
Compatibility
Fit smartphone 4.7” up to 6.2”
Mounting Position
Rear mirror
Adjustable Angle
720 degrees rotated double-ball bracket bases
Input Volt
9-38V
Output Volt
5V 2A / 9V 1.5A
Wireless Charging
10W / 7.5W /5W
Material
Aluminum alloy, Silicon rubber, 304 stainless steel
Waterproof Level
IP67
Size/Weight
170×70×100mm / 245g
Working Temp
-20℃-60℃
FEATURES
⚫ Efficient wireless charging speed with maximum 10W output just simply attach your smartphone
⚫ 720 degrees rotated double-ball bracket bases can be adjusted easily for perfect viewing angles
⚫ IP67 waterproof, dustproof and anti-UV design to fit any environments
⚫ Foreign Object Detection technology, once a foreign object been detected, the charging will stop to
avoid any potential short circuit or catching fire
⚫ Automatic heat dissipation to prevent overheating from charging
Loading...