Assembly Instruction Sheet
ToolsRequired: Flatheadscrewdriver,Phillipsscrewdriver,pliers,wire cutters,wirestrippers, electricaltape,safety glasses.
LightSource:
EstimatedAssembly Time:
Preparation:
present.Ifany partsaremissing ordamaged,do notattemptto assemble,install,or operatethefixture. Contactcustomerservice forreplacement
parts.
Note: This CONVERTIBLE fixture can be mounted as pendant light or semi-flush light. Refer to respective
installation steps for installations.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
(1)A19 MediumBasebulb 100WMaximum.
30-45minutes
Identifyandinspect allpartsbefore beginninginstallation.Check packagecontentlist anddiagramsbelow tobesure allpartsare
Package Contents
A
6” Rod
B
x2
12” Rod
C
Flat
Washer
x1
Fixture Body
I
x1
J
x2
Swivel
H
x1
Upper Collar
x1
D
G
Hex
Nut
x3
E
Nipple
x1
Crossbar
Assembly
x1
Ceiling
F
Canopy
x1
Shade
x1
Q
K
Diffuser
x1
R
S
Steel Collar
L
x1
Harp with
Socket Collar
M
x1
Nipple
N
x1
Flat Washer
O
x1
Rubber Washer
P
x1
Small Flat
Washer
x1
Finial
x1
(Continue to Step 1A)
(B/C) and the Ceiling Canopy with Swivel.
Thread the Fixture Body (I), the chosen
Rods (B/C) and the Ceiling Canopy with
Swivel together. Hand tighten until snug.
Suggested rods for Ceiling height :
8’ ceiling : use (2) 12” rods
9’ ceiling : use (2) 6” rods and (2) 12” rod
Supply Wires and
Ground Wire
Figure 1A
STEP 2A - Installing the Crossbar Assembly
A. Pass the supply wires from outlet box through the Crossbar
Assembly (A). Attach the Crossbar Assembly (A) to the outlet box
with the head of the green ground screw facing you. Secure the
Crossbar Assembly (A) with outlet box screws (not included).
Tighten until snug.
Figure 2A
I
E
G
H
B
Outlet
Box
A
D
F
B
C
C
Assembly Instructions for Pendant Light
(Step 1A - Step 7A)
STEP 1A - Install Ceiling Canopy, Rods and Socket Assembly
together
A. Thread Nipple (G) onto the Swivel (H). Place Ceiling Canopy (F) and
Flat Washer (E) over the Nipple (G), secure by threading Hex Nut
(D) onto the Nipple (G), tighten until sung.
B. Determine the Rods (B/C) to be assembled to the Fixture Body (I)
according to your hanging height.
C. Pass the supply wires and ground wire through the chosen rods
Thank youforpurchasinga product.
Need assistancewithparts or assembly? Call our customerservice
Outlet Box Screws
(not included)
STEP 3A - Test Fitting Ceiling Canopy to Crossbar Assembly
A. Remove mounting balls from the Crossbar Assembly (A). Fit the
Ceiling Canopy (F) to the CrossbarAssembly (A) and secure with
mounting balls. Note: The Ceiling Canopy (F) should be snug
against the ceiling and the mounting balls. If not, adjust the length of
the nipple on the Crossbar Assembly (A) by unscrewing the
preassembled hex nut and lock washer and then screwing the
mounting screws in or out of the crossbar until the correct length is
1of4
Supply Wires
with Ground Wire
(Step 3A Continued)
STEP 7A Install Diffuser-
achieved. Once the Ceiling Canopy (F) is secure, remove the
mounting ball and Ceiling Canopy (F) and proceed to Step 4A.
A
Hex Nut and
F
Figure 3A
STEP 4A - Wire Connections
Wrap bare or green ground wire around green ground screw on the
A.
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
from outlet box
Black wire from
outlet box (or Red)
Bare, or Green
Ground wire
from outlet box
Green Ground Screw
on the Crossbar
STEP 5A Install the Fixture-
A. Carefully tuck all wires into the outlet box and position the Ceiling
Canopy (F) over the outlet box.Align the holes in the ceiling canopy
with the mounting screws, then attach the Ceiling Canopy (F) using
the previously removed mounting balls. Hand tighten until snug.
F
Lock Washer
Mounting Screw
Mounting Ball
White wire
from fixture
Black wire
from fixture
Ground wire
from Fixture
Figure 4A
A
Mounting Screw
A. Thread one Hex Nut (D) to the Nipple (N)
approx half way. Screw the Nipple (N)
into the bottom end of the Harp (M) and
tighten until snug. By using pliers,
thread the Hex Nut (D) against the Harp
(M) and hand tighten until snug.
B. Thread another Hex Nut (D) onto the end
of the Nipple (N) and adjust it to proper
location for rest components. Attach the
Flat Washer (O), the Rubber Washer (P),
the Diffuser (Q) and the Small Flat
Washer (R) over the Nipple (N) in turn.
Secure them with the Finial (S) and hand
tighten until snug.
Your fixture is now assembled
and ready to use. Enjoy!
N
O
R
Figure 7A
D
D
P
S
Assembly Instructions for Semi-flush Light
(Step1B-Step7B)
Part B, Part C and Part H will not be used in the assembly of the
Semi-Flush Light fixture. Please set aside these parts.
6” Rod
B
x2
12” Rod
C
x2
STEP 1B Install Ceiling Canopy to SocketAssembly-
A. Pass supply wires with ground wire through Nipple (G), Ceiling
Canopy (F), Flat Washer (E) and Hex Nut (D). Thread Nipple (G)
onto the Fixture Body (I). Place the Ceiling Canopy (F) and the Flat
Washer (E) onto the Nipple (G). Secure by threading the Hex Nut (D)
onto the Nipple (G). Hand tighten until snug. Cut the wires leaving
approximately 6” of wire extending from the Ceiling Canopy.
B. Optional Swivel: Install the swivel to the Fixture Body (I) and then
attach Nipple (G) and the Ceiling Canopy (F) to the Swivel using the
Flat Washer (E) and the Hex Nut (D).
Extra Parts include
H
Swivel
x1
M
Q
Figure 5A
STEP 6A Install Shade and Bulb-
A. Place the Upper Collar (J), the
Shade (K) and the Steel Collar (L) in
turn and secure with the Harp with
Socket Collar (M). Hand tighten until
snug.
B. Insert the bulb onto socket and
screw snugly into place.
Mounting Ball
Supply Wires
with Ground Wire
E
Socket
J
K
L
M
Bulb (not
supplied)
Figure 6A
Thank youforpurchasinga product.
Need assistancewithparts or assembly? Call our customerservice
2of4
Optional
Swivel
Figure 1B
D
F
G
I
STEP 2B - Installing the Crossbar Assembly
STEP 5B Install the Fixture-
A. Pass the supply wires from outlet box through the Crossbar
Assembly (A). Attach the Crossbar Assembly (A) to the outlet box
with the head of the green ground screw facing you. Secure the
Crossbar Assembly (A) with outlet box screws (not included).
Tighten until snug.
Outlet
Box
Figure 2B
A
Outlet Box Screws
(not included)
STEP 3B - Test Fitting Ceiling Canopy to Crossbar Assembly
A. Remove mounting balls from the Crossbar Assembly (A). Fit the
Ceiling Canopy (F) to the CrossbarAssembly (A) and secure with
mounting balls. Note: The Ceiling Canopy (F) should be snug
against the ceiling and the mounting balls. If not, adjust the length of
the nipple on the Crossbar Assembly (A) by unscrewing the
preassembled hex nut and lock washer and then screwing the
mounting screws in or out of the crossbar until the correct length is
achieved. Once the Ceiling Canopy (F) is secure, remove the
mounting ball and Ceiling Canopy (F) and proceed to Step 4B.
A
F
Supply Wires
with Ground Wire
Hex Nut and
Lock Washer
Mounting Screw
Mounting Ball
A. Carefully tuck all wires into the outlet box and position the Ceiling
Canopy (F) over the outlet box.Align the holes in the ceiling canopy
with the mounting screws, then attach the Ceiling Canopy (F) using
the previously removed mounting balls. Hand tighten until snug.
A
F
Figure 5A
STEP 6B Install Shade and Bulb-
A. Place the Upper Collar (J), the
Shade (K) and the Steel Collar (L) in
turn and secure with the Harp with
Socket Collar (M). Hand tighten until
snug.
B. Insert the bulb onto socket and
screw snugly into place.
STEP 7B Install Diffuser-
Mounting Screw
Mounting Ball
Socket
J
K
L
M
Bulb (not
supplied)
Figure 6B
Figure 3B
STEP 4B - Wire Connections
Wrap bare or green ground wire around green ground screw on the
A.
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
from outlet box
Black wire from
outlet box (or Red)
Bare, or Green
Ground wire
from outlet box
Green Ground Screw
on the Crossbar
White wire
from fixture
Black wire
from fixture
Ground wire
from Fixture
Figure 4B
A. Thread one Hex Nut (D) to the Nipple (N) approx half way. Screw the
Nipple (N) into the bottom end of the Harp (M) and tighten until
snug. By using pliers, thread the Hex Nut (D) against the Harp (M)
and hand tighten until snug.
B. Thread another Hex Nut (D) onto the end of the Nipple (N) and
adjust it to proper location for rest components. Attach the Flat
Washer (O), the Rubber Washer (P), the Diffuser (Q) and the Small
Flat Washer (R) over the Nipple (N) in turn. Secure them with the
Finial (S) and hand tighten until snug.
Your fixture is now assembled and ready to use.
Enjoy!
M
D
N
D
P
Q
S
Figure 7B
O
R
Thank youforpurchasinga product.
Need assistancewithparts or assembly? Call our customerservicer
3of4
FINISH: IMPERIAL SILVER
PENDANT LIGHT
5” Dia.
13.5” Dia.
OVERALL HEIGHT
51”
INCLUDES (2) 6”
AND (2)12” RODS
11. 5”
SEMI-FLUSH
5” Dia.
13”
13.5” Dia.
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/4"
Thank youforpurchasinga product.
Need assistancewithparts or assembly? Call our customerservice
4of4
Loading...