Assembly Instruction Sheet
Flatheadscrewdriver,Phillips screwdriver,pliers, wire cutters,wirestrippers, electrical tape, safetyglasses.
ToolsRequired:
BulbRecommended:
EstimatedAssembly Time:
Preparation:
present.Ifany parts are missingordamaged, do not attempttoassemble, install, or operatethefixture. Contact customer serviceforreplacement
parts.
Fixturecanonly be mounted inthedirection indicated on page2.
Identifyandinspect all parts beforebeginninginstallation. Check package contentlistand diagrams below tobesure all parts are
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
(3)CandelabraBase 60W Maximum,Alternate bulb (3) 13WCFL
30-45minutes
Package Contents
Fixture
Body
A
x1
STEP 1 Install Shade-
A. Unscrew the Lock Screw, remove the Cage, the Glass Shade and the
Tab from the Fixture Body (A). Remove the Styrofoam from inside of
the shade.
B. Place Glass Shade into the Cage, secure by place the Tab into the
Cage press on the Glass Shade.
C. Set the Cage with Glass Shade into the Cap on the Fixture Body (A),
secure by threading the Lock Screw into the Cap, tighten until sung.
Crossbar Assembly
B
x1
Fixture Body
Tab
Glass Shade
STEP 2 Install Inner Backplate-
A. Pass the supply wires through the CrossbarAssembly (AA). Attach
the Crossbar Assembly (AA) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included). Tighten until snug.
Supply Wires with
Outlet Box
Figure 2
STEP 3 Fit Fixture Body to
A. Remove mounting balls from the
STEP 4 - Wire Connections
-
Crossbar Assembly
Crossbar Assembly (B). Fit the
Fixture Body (A) Crossbar
Assembly (B) and secure with
mounting balls. Note: The
backplate of the Fixture Body (A)
should be snug against the wall
surface and the mounting balls. If
not, adjust the length of the nipple
on the Crossbar Assembly (B) by
unscrewing the preassembled hex
nut and lock washer and then
screwing the mounting screws in or
out of the crossbar until the correct
length is achieved. Once the
backplate of the Fixture Body (A) is
secure, remove the mounting ball
and Fixture Body (A) and proceed
to Step 4.
Ground Wire
B
Outlet Box Screws
(not included)
Mounting
Ball
A
Hex Nut and
Lock Washer
Mounting
Screw
Figure 3
B
Figure 1
A. Use standard wire connectors (not included) to make all wire
Lock Screw
Cage
Thank you for purchasing
1of2
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
White wire
from supply
Black wire from
supply (or Red)
Ground wire
from supply
Figure 4
STEP 5 Install Fixture Body-
A. Carefully tuck all wires into the outlet
box and position the backplate of
fixture body (A) over the outlet box.
Align the holes in the backplate with
the mounting screws. Place caulk (not
supplied) into the previously removed
mounting balls and then attach fixture
body (A) using the mounting balls.
Hand tighten until snug.
Figure 5
White wire
from fixture
Black wire
from fixture
Ground wire
from fixture
Mounting
A
Ball
Mounting
Screw
STEP 6 - Install Bulb
A. This fixture uses candelabra bulb with a
candelabra screw base. Maximum 60
watts.
B. Insert bulb and screw snugly into place.
STEP 7 - Apply Silicone Sealer
A. Make sure exterior wall surface
and fixture backplate are free of
dirt before applying caulk. Using
exterior grade caulk, caulk over
top of backplate and down other
side. Do not caulk bottom of
B
fixture backplate to ensure proper
moisture drainage.
Your fixture is now assembled and
ready to use. Enjoy!
Bulb
Socket
Figure 6
Exterior
Grade
Caulk
Backplate
Figure 7
FINISH: PALLADIAN BRONZE
MYSTIC BLACK
Fixture can only be
mounted in the
direction indicated
8”
5.5”
10”
9” Dia.
14.5”
1
(3)
60W Candelabra
base bulbs
(Not Supplied)
PART NUMBER
NO.
1
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2"
REPLACEMENT PART DESCRIPTION
GLASS CLEAR SEEDY
Thank you for purchasing
2of2
REQ.
1
Loading...