LongerPump TS-1A/L0107-1A, TS-2A/L0107-2A, TS-1B/W0109-1B Operating Manual

SYRINGE PUMP OPERATING MANUAL

Important Information:

Please read operating manual carefully before operation.

Warning:

Over-push or over-draw the syringe may result in the fluid
sprayed. Use appropriate measures to protect operator
and equipment. Be careful during operation.

When the fluid sprays out on the drive unit please shut
down the power supply immediately and clean the drive
unit, then turn on the power supply.

If a trouble happens please contact us or our dealer. Don't
repair the equipment by yourself.

Be careful when inserting or extracting the connection
wire between controller and drive unit to prevent the plug
from damaging.

If the power line or the plug are worn or damaged please
pull out the plug.

Please shut down the power supply before connecting the
external control equipment.

TableofContents

Introduction
Operation Panel
Basic Operation

Start/Stop Key
Fast Forward Key
Fast Reverse Key

Rotary Coded Switch
Channels Switch Key
Exit Key

Menu Frame Work
Multi-channel Running Interface
Multi-channel Functions Setting

Select Drive Unit
Select Copy Parameters
Set Delay Time
Controller I.D.

Single Channel Running Interface
Single Channel Functions Setting

Working Mode Selection
Syringe Select
Dispense Parameters Setting
Calibration
Display Select

Acceptable Drive Units and Syringes
Syringe Loading
External Control Function
Maintenance
Warranty
Technical Specifications

1

2

2

2

2

2

2

2

2

3

4

4

4

5

5

6

6

8

8

9

11

15

16

17

19

21

21

21

22

SYRINGE PUMP OPERATING MANUAL SYRINGE PUMP OPERATING MANUAL

Introduction

TS series products are controllers of four channels and multi-function
syringe pumps. They need to be connected with drive units to constitute
syringe pump systems of strong functions and easy-to-operate. They are
widely used in biological laboratory. There are 3 types:

Controller Type

TS-1A

TS-2A

TS-1B

S2

S1

F1 Power Switch

F2 Power Socket

F3DriveUnitSocket

F4 External Control Input and Communication Interface

F5 External Control Output Interface

Note:

Controller and drive unit are connected through 8 pin S terminal.
Be careful when insertion or extraction. Please see page 21 for
detail information about control function.External

DriveUnitType

L0107-1A

L0107- A

W0109-1B

F1
F2

F3

Working Mode

Infusion-only

2

Infusion/Withdrawal

Infusion/Withdrawal

S3

S1 Controller

S2 Drive Unit

S3 Glass Syringe

F5

F4

Operation Panel

Fast Forward Key

Exit Key

Channels Switch Key

Fast Reverse Key

Start/Stop Key

Rotary Coded Switch

Basic Operation

Start/Stop Key
Press the Start/Stop Key to start or stop the pump. In multi­channel working mode, to pause the running state, the pump will
prompt if continue the current working state.
Fast Forward Key
In multi-channel working mode, pressing the Fast Forward Key all
the enabling channels infuse at the max. speed. In single channel
working mode, pressing the Fast Forward Key this channel infuses
at the max. speed. Loose this key the pump stops. Other keys are
invalid when pressing this key.
Fast Reverse Key
In multi-channel working mode, pressing the Fast Reverse Key all
the enabling channels withdraw at the max. speed. In single
channel working mode, pressing the Fast Reverse Key this channel
withdraws at the max. speed. Loose this key the pump stops. Other
keys are invalid when pressing this key.

Note: Fast Forward Key and Fast Reverse Key are invalid when the
pump is in running state.

Rotary Coded Switch (RCS)
Turn the Rotary Coded Switch for menu selection or parameter
setting. Press the Rotary Coded Switch for confirmation.

Note: Put the finger in the center of the switch to press the RCS.
Put the finger on the small concave which is on the side of the
switch to turn the RCS.

Channels Switch Key
Switch between different channels.

Exit Key
Cancel current operation and return to previous menu.

1

2

SYRINGE PUMP OPERATING MANUAL SYRINGE PUMP OPERATING MANUAL

Menu Frame Work

1#:
2#:
3#:
4#:

Select Unit：

1# 2# 3# 4#

Copy Para Sel：

1# 2# 3# 4#

Delay time：

1# 6.0 sec
2# 0.0 sec
3# 0.0 sec
4# 0.0 sec

Controller ID：

1# 50.00 nL/sec

Syringe： 100 Lμ

2#V ： 360ol Lμ

Syringe： 500 Lμ

3# ： 860 LμVol

Syringe： 1000 Lμ

4# ：700 nLVol

Syringe：10Lμ

1

20.0 sec

40 sec 5

68.3 sec 10

25 sec 1

Mode Select

yringe Select

S

Dispense Para
Calibration
Display Select

Mode Select

yringe Select

S

Dispense Para
Calibration
Display Select

Mode Select

yringe Select

S

Dispense Para
Calibration
Display Select

Mode Select

yringe Select

S

Dispense Para
Calibration
Display Select

Mode Select

yringe Select

S

Dispense Para
Calibration
Display Select

Infusion
Withdrawal
I/W
W/I
Continuous

Unimetrics

Becton Dickinson

Hamilton

Barrel I.D.

Disp Vol Unit

186 0.01

Infusion Unit

8.5

ithdrawal Unit

W

7.0

Copy No.:

ause Time:

P

Vol 50.00：
Time 60sec

：

Act 50.00 L

Display Select
Volume
Speed
Flow

L

μ

sec

sec

10

min

0.1

μμL

：

：

Save change?

Yes o CancelN

Multi-channel Running Interface

Switch on the pump. First initializing, and then display the running
interface.

a

2#:

1#:

e

3#:

b

a. Enabling symbol: Symbol of enabling or disabling the channels.

Means enabling the current channel. means disabling the
current channel. The disabling channel is invalid when the pump is
in running state or switching the channels.

b. Channel number: Channel serial number.
c. Start/Stop state: Display the state of current channel.

Start displays Stop displays Pause displays

d. Direction: Display running direction. Infusion displays .

Withdrawal displays .

e. Working mode: Display current working mode. Display in

“infusion, withdrawal, infusion/withdrawal, withdrawal/infusion”
modes. Display in “continuous” mode.

4#:

d
c

.. .

Multi-channel Functions Setting

Select Drive Unit:

Means enabling the current channel. Means disabling the current

channel. The disabling channel will not work when the pump is
working. The setting method is as below:

1#:
2#:
3#:
4#:

Press the RCS

Press the

Exit Key

Select Unit：

1# 2# 3# 4#

Copy Para Sel：

1# 2# 3# 4#

Select “Yes”
or “No”

Save change?

Yes o Ca ncelN

Turn the RCS to select
if save the change

Press the RCS

Press the

Exit Key

Select
“Cancel”

Select Unit：

1# 2# 3# 4#

Copy Para Sel：

1# 2# 3# 4#

PresstheRCStoset
the enabling channels

Turn the RCS

Select Unit：

1# 2# 3# 4#

Copy Para Sel：

1# 2# 3# 4#

Turn the RCS to
select the channels

3 4

SYRINGE PUMP OPERATING MANUAL SYRINGE PUMP OPERATING MANUAL

Select Copy Parameters

Select the parameters of one drive unit as copy parameters, all
enabling channels will run according to copy parameters. Not setting
copy parameters each enabling channel will run according to its own
parameters setting. Means copy channel; means non-copy
channel. Only one channel can be selected as copy channel, or non­copy channel is acceptable. The setting method is as below:

1#:
2#:
3#:
4#:

Set Delay Time

Press and
turn the RCS

Press the

Exit Key

Select Unit：

1# 2# 3# 4#

Copy Para Sel：

1# 2# 3# 4#

Select “Yes”
or “No”

Save change?

Yes o Ca ncelN

Turn the RCS to select
if save the change

Press the RCS

Press the

Exit Key

Select
“Cancel”

Select Unit：

1# 2# 3# 4#

Copy Para Sel：

1# 2# 3# 4#

Turn the RCS to select
the copy channel

Turn the RCS

Select Unit：

1# 2# 3# 4#

Copy Para Sel：

1# 2# 3# 4#

PresstheRCStoset
the copy channel

Set delay time to start each drive unit in turn. Time units are sec,
min and hour. Time numerical value is from 0.1 to 999.9. The
setting method is as below:

1#:
2#:
3#:
4#:

Press the RCS

Press the

Exit Key

Select Unit：

1# 2# 3# 4#

Copy Para Sel：

Turn the RCS

1# 2# 3# 4#

Save change?

Yes o Ca ncelN

Turn the RCS to select if save
the change

Press the RCS

Select “Yes”
or “No”

Select
“Cancel”

Delay time：

1# 6.0 sec：
2# 0.0 sec：
3# 0.0 sec：

Press the

Exit Key

Delay time：

Press the RCS

1# 6.0 sec：
2# 0.0 sec：
3# 0.0 sec：

Turn the RCS to select channel

Press the RCS

Controller I.D.

When control computer controls many pumps through RS485
interface, it must identify each controller's I.D.. This controller I.D.
should be unique. It's the identification of this controller.
The controller address serial number is from 1 to 30. The default is

1. The setting method is as below:

1#:

Press the RCS

2#:
3#:
4#:

Press the

Exit Key

Single Channel

Select Unit：

1# 2# 3# 4#

Copy Para Sel：

1# 2# 3# 4#

Save change?

Yes o Ca ncelN

Turn the RCS to select
if save the change

Turn the RCS

Select “Yes” or “No”

Select
“Cancel”

Press the RCS

Controller ID：

Controller ID：

Turn the RCS to set the
controller I.D.

Running Interface

Switch on the pump. First initializing, and then display the multi­channel running interface. Press Channels Switch Key to enter single
channel running interface. Please see below for detail operation:

1# 1.860 L

Vol

： μ

8.3 sec 10

Syringe

： 100 Lμ

Press Channels
Switch Key

2# 1.860 L

Vol

： μ

8.3 sec 10

Syringe

1#:
2#:
3#:
4#:

Press Channels
Switch Key

Press the Exit Key

： 100 Lμ

Press Channels
Switch Key

3# 1.860 L

Vol

： μ

8.3 sec 10

Syringe

： 100 Lμ

1

Press the RCS

1

1# 6.0 min：
2# 0.0 sec：
3# 0.0 sec：
4# 0.0 sec：

Turn the RCS to set the delay time

Press the RCS

5

Delay time：Delay time：

1# 6.0 min：
2# 0.0 sec：
3# 0.0 sec：
4# 0.0 sec：

Turn the RCS to set the time unit

Press Channels
Switch Key

4# 1.860 L

Vol

： μ

8.3 sec 10

Syringe

： 100 Lμ

6

SYRINGE PUMP OPERATING MANUAL SYRINGE PUMP OPERATING MANUAL

Three Display Modes for Single
Channel Running Interface:

Volume Display

a.
b.

c.
d.

1# 1.860 L

Vol

： μ

8.3 sec 10

Syringe

： 100 Lμ

e.

f.

g.

Speed Display

1#： 6.715mm/min

8.3 sec 10

Syringe

： 100 Lμ

Flow Rate Display

1#： 224.0nL/sec

8.3 sec 10

Syringe

： 100 Lμ

a.Display mode: Display the current volume, flow rates or speed.

Please see page 16 “Display Select” for setting method.

b.Time: Required time for one time infusing or withdrawal.

Counting down when running.
c.Syringe: Display selected syringe.
d.Start/Stop state: Start displays Stop displays Pause

displays

.

e.Copy number: Display dispensing copy number. Counting down

when running (no display in “continuous” mode).
f. Working mode: Display current working mode. Display in

“infusion, withdrawal, infusion/withdrawal, withdrawal/infusion”

modes. Display in “continuous” mode.
g.Direction: Display running direction. Infusion displays .

Withdrawal displays .

;;

Single Channel Functions Setting

5 functions are set:

1# 1.860 L

Vol

： μ

Press the RCS

8.3 sec 10

Syringe

： 100 Lμ

Please see page 16 “Display
Select” for “Speed” and
“Flow” display.

Press the Exit Key

Press the

Exit Key

Note: TS-1A controller disables Mode Select. It only has infusion
working mode.

Working Mode Selection

1# 1.860 L

Vol

： μ

8.3 sec 10

Syringe

： 100 Lμ

Please see page16 “Display
Select” for “Speed” and
“Flow” display.

Note:

Select “Yes” to save the

current setting

Select“No”nottosave

the setting

Select “Cancel” to return

to previous menu and

keep on selecting

Press the RCS

Press the

Exit Key

Mode Select

yringe Select

S

Dispense Para
Calibration

Turn the RCS to select
working mode

Select “Yes”
or “No”

Save change?

Yes o Ca ncelN

Turn the RCS to select
if save the change

Prompts

Infusion: The pump infuses during the whole working course
Withdrawal: The pump withdraws during the whole working course
Infusion/Withdrawal: The pump infuses first and then withdraws during the

Withdrawal/Infusion: The pump withdraws first and then infuses during the

Continuous: The pump infuses first and then withdraws, and then cycles

Please see page 11 “Dispensing Parameters Setting” to set the parameters for

whole working course

whole working course

continuously

above working modes.

Mode Select

yringe Select

S

Dispense Para
Calibration

Turn the RCS

Display Select

Press the RCS

Press the RCS

Select
“Cancel”

Infusion
Withdrawal
I/W
W/I

Turn the RCS to
select working mode

Tur n t he RCS

Continuous

Turn the RCS to
select working mode

87

SYRINGE PUMP OPERATING MANUAL SYRINGE PUMP OPERATING MANUAL

Syringe Select

Select Standard Syringe

Press and

1# 1.860 L

Vol

： μ

8.3 sec 10

Syringe

： 100 Lμ

Please see page 16 “Display
Select” for “Speed” and
“Flow” display.

Note:

Select “Yes” to save the

current setting

Select“No”nottosave

the setting

Select “Cancel” to return

to previous menu and

keep on selecting

turn the

RCS

Press the

Exit Key

Mode Select

yringe Select

S

Dispense Para
Calibration

Turn the RCS to highlight
“Syringe Select”

Select “Yes” or “No”

Save change?

Yes o Ca ncelN

Turn the to select

RCS

if save the parameter

Press the RCS

Press the Exit Key

Unimetrics
Becton Dickinson
Hamilton
Barrel I.D.

Turn the to select
the type

Press the RCS

Size Select

5102550

Select
“Cancel”

100 250 500 1000

I.D.

Turn the to select
the specification

RCS

Press the RCS

()μL

： 1.13mm

RCS

Three syringe manufacturers are listed in the TS-1A,TS-2A menu.
Please see below table for specifications:

Unimetrics

Hamilton

SGE

Spec L()μ

I.D. mm()

μ

Spec L()

I.D. mm()

Spec L()μ

I.D. mm()

10

0.46

25

0.73

50

1.03

100

1.46

250

2.3

10 25 50 100 250 500

0.48

25

0.73

0.73

50

1.03

1.03

100

1.46

1.46 2.3 3.26

250

2.3

500

3.26

500

3.26

1000

4.61

Three syringe manufacturers are listed in the TS-1B menu. Please see
below table for specifications:

Unimetrics

Becton
Dickinson

Hamilton

Spec L()μ

I.D. mm()

Spec cc()

I.D. mm()

Spec m()L

I.D. mm()

10

0.46

1

4.7

1

4.61

25

0.73

3

8.59

2.5

7.28

50

1.03

5

11.99

5

10.3

100

1.46

250

2.3

500

3.26

1000

4.61

10

14.482019.053021.596026.6

10

14.572523.035032.57

Setting and Select the Inner Diameter of the Syringe

1. Setting the Inner Diameter of the Syringe
If the syringe used is not listed in the menu the inner diameter of
the syringe needs to be measured and entered (0.01 mm - 40 mm).
The pump can save 4 inner diameters of the syringes.

1#

Vol

：

1.860 Lμ

8.3 sec 10

Syringe

： 100 Lμ

Please see page 16 “Display
Select” for “Speed” and
“Flow” display.

Note:

Select “Yes” to save the

current setting

Select“No”nottosave

the setting

Select “Cancel” to return

to previous menu and

keep on selecting

1# 8.00mm

：
：

2# 10.00mm

：

3# 10.00mm

：

4# 10.00mm

Select “Yes”

Save change?

Yes o Ca ncelN

Turn the to select
if save the change

RCS

Press and
turn the

RCS

Press the

Exit Key

Select “No”

Press the RCS

Select
“Cancel”

Mode Select

yringe Select

S

Dispense Para
Calibration

Turn the to highlight

RCS

the Syringe Select

“”

Press and
turn the

RCS

Unimetrics
Becton Dickinson
Hamilton
Barrel I.D.

1# 10.00mm

：
：

2# 10.00mm

：

3# 10.00mm

：

4# 10.00mm

1# 8.00mm

：
：

2# 10.00mm

：

3# 10.00mm

：

4# 10.00mm

Turn the to set
the inner diameter

Press the

Exit Key

Press the RCS

Press the RCS

RCS

Select “Yes” or “No”

Press the

Exit Key

Select
“Cancel”

Save change?

Yes o Ca ncelN

Turn the to select
if save the change

RCS

2.Select the Inner Diameter of the Syringe
Select the inner diameter of the syringe after setting the inner diameter.

1# 8.00mm

：
：

2# 15.00mm

：

3# 10.00mm

：

4# 10.00mm

Press the

Exit Key

Select
“Cancel”

Save change?

Yes o Ca ncelN

Turn the to select
if save the change

RCS

Select “Yes”
or “No”

Unimetrics
Becton Dickinson
Hamilton
Barrel I.D.

9

10

SYRINGE PUMP OPERATING MANUAL SYRINGE PUMP OPERATING MANUAL

Dispense Parameters Setting

The dispense parameters include dispense volume, infusion time,
withdrawal time, copy number and pause time.

Dispense volume: It is the volume for one time infusion or withdrawal
The volume range is 1 nL to 99.99 mL
There are volume units of nL, 0.01nL, 0.1µL, µL and 0.01mL available.

Press and

1# L

Vol

：

1.860 μ

8.3 sec 10

Syringe

： 100 Lμ

Please see page 16 “Display
Select” for “Speed” and
“Flow” display.

Note:

Select “Yes” to save the

current setting

Select“No”nottosave

the setting

Select “Cancel” to return

to previous menu and

keep on selecting

Note:

turn the

RCS

Press the

Exit Key

Mode Select

yringe Select

S

Dispense Para
Calibration

Turn the and highlight
the “Dispense Para”

RCS

Select “Yes” or “No”

Select “Cancel”

Save change?

Yes o Ca ncelN

Turn the to select

RCS

if save the parameter

Press the RCS

Press the RCS

Press the

Exit Key

Disp Vol Unit

Infusion Unit

Disp Vol Unit

Infusion Unit

Turn the and set the unitRCS

Disp Vol Unit

Infusion Unit

Turn the to
set the volume

86 0.01 L

1 μ

8.5 sec

Press the RCS

86 0.01 L

1 μ

8.5 sec

Press the RCS

86 0.01 L

1 μ

8.5 sec

RCS

When the one time dispensing volume or the total dispensing volume
(multiply one time dispensing volume by copy number) are more than
the volume of the syringe the running interface will display “Vol
Overflow” (see below). Please change the syringe or adjust the
dispensing volume or the copy number.

Vol overflow！

8.3 sec 10

Syringe: 100 Lμ

Infusion time: It is the time for one time infusion
The range of infusion time is from 0.1 second to 999.9 hours
There are time units of second, minute and hour available

Press and

1#

Vol

：

1.860 Lμ

8.3 sec 10

Syringe

： 100 Lμ

Please see page 16 “Display
Select” for “Speed” and
“Flow” display.

Note:

Select “Yes” to save the

current setting

Select“No”nottosave

the setting

Select “Cancel” to return

to previous menu and

keep on selecting

turn the

RCS

Press the

Exit Key

Mode Select

yringe Select

S

Dispense Para
Calibration

Turn the and highlight

RCS

the Dispense Para

Select “Yes” or “No”

Select “Cancel”

Save change?

Yes o Ca ncelN

if save the change

RCS

Press and turn the RCS

Press the

Exit Key

Disp Vol Unit

86 0.01 L

1 μ

Infusion Unit

8.5 sec

Disp Vol Unit

86 0.01 L

1 μ

Infusion Unit

8.5 sec

Turn the and set the unitRCS

Press the RCS

Disp Vol Unit

86 0.01 L

1 μ

Infusion Unit

8.5 sec

Turnthe tosetthetimeRCSTurn the to select

Press the RCS

Press the RCS

Note:
When the pump can't infuse the setting volume in the setting time

the running interface will display “I-speed Overflow” (see below).
Pleaseadjustthedispensingtimeorthedispensingvolume.

I-speed Overflow！

8.3 sec 10

Syringe: 100 Lμ

11

12

SYRINGE PUMP OPERATING MANUAL SYRINGE PUMP OPERATING MANUAL

Withdrawaltime:Itisthetimeforonetimewithdrawal
The range of withdrawal time is from 0.1 second to 999.9 hours
There are time units of second, minute and hour available

Press and

1#

Vol

：

1.860 Lμ

8.3 sec 10

Syringe

： 100 Lμ

Please see page 16 “Display
Select” for “Speed” and
“Flow” display.

Note:

Select “Yes” to save the

current setting

Select“No”nottosave

the setting

Select “Cancel” to return

to previous menu and

keep on selecting

turn the

RCS

Press the

Exit Key

Mode Select

yringe Select

S

Dispense Para
Calibration

Turn the and highlight
the “Dispense Para”

RCS

Select “Yes” or “No”

Save change?

Yes o Ca ncelN

Turn the to select

RCS

if save the parameter

Press and turn the RCS

Select “Cancel”

Press the RCS

Press the

Exit Key

Withdrawal Unit

8.3 sec

Copy No.:

1

Press the RCS

Withdrawal Unit

8.3 sec

Copy No.:

1

Turn the and set the unitRCS

Press the RCS

Withdrawal Unit

8.3 sec

Copy No.:

1

Turnthe tosetthetimeRCS

Note:

When the pump can't withdrawal the setting volume in the setting
time the running interface will display “W-speed Overflow” (see
below). Please adjust the dispensing time or the dispensing volume.

W-speed Overflow！

8.3 sec 10

Syringe： 100 Lμ

Copy Number: It is the total infusion and withdrawal numbers of the
whole working course. The range is 1 - 999. In Infusion/Withdrawal
(I/W) and Withdrawal/Infusion (W/I) modes, one time working
course is finishing one time infusion and withdrawal.

1#

Vol

：

1.860 Lμ

8.3 sec 10

Syringe

： 100 Lμ

Please see page 16 “Display
Select” for “Speed” and
“Flow” display.

Note:

Select “Yes” to save the

current setting

Select“No”nottosave

the setting

Select “Cancel” to return

to previous menu and

keep on selecting

Note:

When the one time dispensing volume or the total
dispensing volume (multiply one time dispensing volume
by copy number) are more than the volume of the syringe
the running interface will display “Vol Overflow” (see
right). Please change the syringe or adjust the dispensing
volume or the copy number.

Press and
turn the

RCS

Press the

Exit Key

Mode Select

yringe Select

S

Dispense Para
Calibration

Turn the and highlight

RCS

the“DispensePara”

Turn the to select
if save the parameter

Select “Yes” or “No”

Save change?

Yes o Ca ncelN

RCS

Select “Cancel”

Press and turn the RCS

Press the Exit Key

Withdrawal Unit

60.0 sec

Copy No.:

Press the RCS

Withdrawal Unit

60.0 sec

Copy No.:

Turn the and set
the copy number

Vol overflow！

8.3 sec 10

Syringe: 100 Lμ

1

Press the RCS

1

RCS

Pause Time: It is the stop time between two dispensing operation.
Therangeis0.1- 999.9min.

1#

Vol

：

1.860 Lμ

8.3 sec 10

Syringe

： 100 Lμ

Please see page 16 “Display
Select” for “Speed” and
“Flow” display.

Note:

Select “Yes” to save the

current setting

Select“No”nottosave

the setting

Select “Cancel” to return

to previous menu and

keep on selecting

Press and
turn the

RCS

Press the

Exit Key

Mode Select

yringe Select

S

Dispense Para
Calibration

Turn the and highlight

RCS

the“DispensePara”

Select “Yes” or “No”

Save change?

Yes o Ca ncelN

Turn the to select

RCS

if save the parameter

Press and turn the RCS

Press the Exit Key

Pause Time:

0.1 min

Press the RCS

Select “Cancel”

Pause Time:

0.1 min

Turn the and set the pause timeRCS

Press the RCS

13 14

SYRINGE PUMP OPERATING MANUAL SYRINGE PUMP OPERATING MANUAL

Calibration

When the accuracy of the dispensing volume can not reach 0.5% (in
the condition of 30% of max. infusion distance), calibration is

≥

needed to adjust the linear speed of the drive unit.

Press and

1#

Vol 1.860 L：μ

8.3 sec 10

Syringe

： 100 Lμ

Please see page 16 “Display
Select” for “Speed” and
“Flow” display.

Save change?

Yes o Ca ncelN

Turn the to select

RCS

if save the parameter

Note:

Select “Yes” to save the

current setting

Select“No”nottosave

the setting

Select “Cancel” to return

to previous menu and

keep on selecting

turn the

RCS

Press the

Exit Key

Select “Yes” or “No”

Press the RCS

Select “Cancel”

Mode Select

yringe Select

S

Dispense Para
Calibration

Turn the and

RCS

highlight the “Calibration”

Interface A

10% 50% 80%

Vol：
Time 60sec

：

Act 10.00 Lμ

：

Turn the to enter
the calibration volume

Turn the to select
if save the parameter

RCS

Select “Yes” or “No”

Save change?

Yes o Ca ncelN

RCS

Press the RCS

Press the Exit Key

Press the

Key

Press the RCS

Press the RCS

Select “Cancel”

Turn the to enter
the actual volume

Vol 10.00：

：

Time 60sec

：

Act 10.00 L

Start/Stop

to start the test

Vol 10.00：

：

Time 60sec

：

Act 10.00 L

Press the RCS

Vol 10.00：

：

Time 60sec

：

Act 10.00 L

RCS

Volume (Vol): The required volume for calibration
Enter volume setting interface (see Interface A) and turn the
to set the calibration volume. There are 10%, 50% and 80% of the
syringe volume available. When selecting the user-defined syringe
the default calibration volume is 50% of the syringe volume. Please
see page 9 “Syringe Select” to select suitable syringe.
Time: The calibration time for the pump is 1 minute.
Actual volume (Act): Press the after setting the

Start/Stop Key

calibration volume. Enter the actual volume.

μμL

Press the RCS

μμL

μμL

RCS

Display Select

Press and

1#

Vol 1.860 L：μ

8.3 sec 10

Syringe

： 100 Lμ

Please see page 16 “Display
Select” for “Speed” and
“Flow” display.

Note:

Select “Yes” to save the

current setting

Select“No”nottosave

the setting

Select “Cancel” to return

to previous menu and

keep on selecting

turn the

RCS

Press the

Exit Key

Display Select

Turn the and highlight

RCS

the “Display Mode”

Select “Yes” or “No”

Press the RCS

Press the

Exit Key

Display Select
Volume
Speed
Flow

Turn the to select
the Display Mode

Press the RCS

Save change?

Yes o Ca ncelN

Turn the to select
if save the parameter

RCS

Select “Cancel”

RCS

There are volume, speed and flow rate display modes available.

Volume: Display current one time infusion or withdrawal volume

Speed: Display current running speed

Flow rates (Flow): Display current flow rates

：

15

16

SYRINGE PUMP OPERATING MANUAL SYRINGE PUMP OPERATING MANUAL

Acceptable Drive Units and Syringes

T -1A/L0107-1A、S TS-2A/L0107-2A

Drive Unit

Controller

Reference Flow Rates List

Syringe Material

Glass Syringe

Specification

（（μL

Glass Syringe

Inner Diameter

(mm)

Flow Rate

/min))

10 25 50 100 250 500 1000

0.46

1.318nL

13.18μL

-

0.73

3.320nL

-

33.20μL

Glass Syringe

1.03

6.610nL

13.282nL

-

66.10μL

132.82μL

1.46 2.3 3.26 4.61

32.96nL

-

329.6μL

-

Glass Syringe

66.22nL

132.42nL

-

662.2μL

1324.2μL

TS-1B/W0109-1B

Glass Syringe

Drive Unit

Controller

Syringe Material

Syringe

Specification

（（μL)

Flow Rate

/min)

Syringe Material

Syringe

Specification

（（cc

Flow Rate

/min))

Syringe Material

Syringe

Specification

-

（（mL

Flow Rate

/min))

10 25 50 100 250 500 1000

1.318nL

13.18μL

0.138

1.38

0.132

1.32

3.320nL

-

33.20μL

1

μLmL0.460

-

1

μLmL0.330

-

-

35

-

4.60

2.5

-

3.30

Glass Syringe

6.610nL

-

66.10μL

Plastic Syringe

μLmL0.896

μLmL1.306

-

8.96

Plastic Syringe

5

μLmL0.661

μLmL1.323

-

6.61

13.282nL

132.82μL

32.96nL

-

329.6μL

10 20

-

μLmL2.261

-

13.06

10 25 50

-

22.61

μLmL3.305

-

13.23

-

33.05

66.22nL

-

662.2μL

30

μLmL2.904

-

29.04

μLmL6.610

-

66.10

132.42nL

1324.2μL

60

μL

4.409

mL

44.09

μL

mL

-

μL

­mL

17 18

SYRINGE PUMP OPERATING MANUAL SYRINGE PUMP OPERATING MANUAL

Syringe Loading

TS-1A/L0107-1A

Loading Pole

2. See above drawing
to load the glass
syringe

TS-2A/L0107-2A

Loading Pole

Pressing Knob

Pressing Knob

1. Lift up and rotate
the pressing knob

3. Lift up the pressing
knob and rotate the
press knob according
to the arrowhead
direction to fix the
glass syringe

1. Lift up and rotate
the pressing knob.
Rotate and loose
the tightening
knobs according to
the arrowhead
directions

TS-1B/W0109-1B

Plunger Fixing Board

Barrel Fixing Board

1.Rotate the tightening
knobs according to the
arrowhead directions.
Loose the plunger fixing
board and the barrel
fixing board

Pressing Knob

2.Lift up the pressing knob
and rotate the pressing
knob according to the
arrowhead direction.
Load the syringe. Rotate
the pressing knob to
press the syringe

2. See above drawing
to load the glass
syringe. Lift up the
press knob and
rotate the press
knob according to
the arrowhead
direction to press
the glass syringe

Tightening
Knob 2

Tightening
Knob 1

19

3. Rotate the tightening
knobs according to
the arrowhead
directions to fix the
glass syringe

3.Tighten the tightening
knobs according to the
arrowhead directions to
fix the syringe

20

SYRINGE PUMP OPERATING MANUAL SYRINGE PUMP OPERATING MANUAL

External Control Function

External Control Output Interface

Channel 1

1234

Start/Stop State
Output

Direction State
Output

External Control Input and Communication Interface

Port Definition:
1# +5V
2# COM
3# COM for external control start/stop
4# External control start/stop: change to high level, start and stop

states switch
5# NC
6# COM for Rs485
7# RS485 B
8# RS485 A
Note: 1 - 3# are RS485 communication bus ports. Can connect to
the control computer (computer, PLC, SCM).

Stop State: OC gate is open

Running State: OC gate is close

Infusion: OC gate is open

Withdrawal:OCgateisclose

Channel 2 Channel 3 Channel 4

5678

9101112

13 14 15 16

（1 2)(5 6)(9 10)(13 14)

are 4 suits OC gates

（3 4)(7 8)(11 12)(15 16)

are 4 suits OC gates

12345678

Maintenance

Keep the surface of the pump clean and dry. Prevent the liquids
from entering the inner of the drive units.
The surface of drive units are not organic solvent and aggressive
liquids resistant. Please pay attention when using.

Note
If a trouble happens, please contact us or our dealers.

Warranty

The warranty period for this product is one year. If repair or
adjustment is necessary within the warranty period, the problem
will be corrected at no charge if it is not due to misuse or abuse on
your part, as determined by the manufacturer. Repair costs outside
the warranty period, or those resulting from product misuse or
abuse,maybeinvoicedtoyou.

TS-1A/L0107-1A、TS-2A/L0107-2A、TS-1B/W0109-1B

Technical Specifications

System Functions

Parameters Setting: The parameters of each channel can be different

Parameters Saving: The parameters of each channel can be saved

Running Control: Each drive unit can be controlled separately; Or four

drive units can be controlled to run simultaneously or run at
different time

Copy Channel: All drive units can be run according to the parameters of

one drive unit of them

Delaying Startup: Delaying startup time of each channel can be

controlled separately

Memory Function: Select resume operation or remain stopped when

power returns after an interruption

Block Protection: When one drive unit stops accidently, the system will

warm and stop

External Control: Each channel has two ways OC gate output to

indicate the start/stop and running direction of this channel

Communication: Realize computer control through RS485

communication interface

Main Functions for Each Channel

Syringe Selection: The syringe can be selected in the manufacturer

table which includes manufacturer and size

User-defined Syringe: 4 inner diameter of user-defined syringe barrel

canbeinputandsaved

Working Mode Setting: TS-1A has only infusion working mode. TS-

2A/TS-1B has 5 working modes available: infusion, withdrawal,
infusion/withdrawal, withdrawal/infusion, continuous

Parameters Setting: Set dispensing volume, infusion time, withdrawal

time, pause time and copy number

Display Mode Selection: Different parameters (volume, flow rate,

linear speed) can be selected in the main display interface

FastForward&FastReverse:Infusionorwithdrawalatthemax.speed

Calibration: Acquire accurate volume through calibration

21

22

SYRINGE PUMP OPERATING MANUAL SYRINGE PUMP OPERATING MANUAL

TS-1A/L0107-1A, TS-2A/L0107-2A Specifications

Max. Infusion Distance: 70 mm

AcceptableGlassSyringe:5µL-1000µL

Linear Speed: 7.94 µm/min - 79.4 mm/min

Adjusting Resolution: 7.94 µm/min

Distance Resolution: 0.165 µm

Linear Force: 20 N

Setting Mode: Membrane Keypad and rotary coded switch

Accuracy: 0.5% error in the condition

Display: 128x64 graphic LCD

External Control: Input control: start/stop

Communication Interface: RS485

Power:AC100V-240VorDC12V/3.2A

Power Consumption: 24W

OperatingCondition:Temperature0-40

ControllerDimensions(L×W×H):235×178×74

Controller Weight: 0.9 Kg

DriveUnitDimensions(L×W×H):180×46×78(mm)

DriveUnitWeight:0.6Kg

IP Rating: IP21

>

≤±

of 30% of max. infusion distance

≥

Output control: start/stop, direction (OC gate)

≤

℃

Relative humidity ‹ 80 %

TS-1B/W0109-1B Specifications

Max. Infusion Distance: 90 mm

AcceptableSyringe:5µL-60mL

Linear Speed: 7.9 µm/min - 79.4 mm/min

Adjusting Resolution: 7.94 µm/min

Distance Resolution: 0.165 µm

Linear Force: 90 N

Setting Mode: Membrane Keypad and rotary coded switch

Accuracy: 0.5% error in the condition

Display: 128x64 graphic LCD

External Control: Input control: start/stop

Communication Interface: RS485

Power:AC100V- 240VorDC12V/3.2A

Power Consumption: 34W

OperatingCondition:Temperature0-40

ControllerDimensions(L×W×H):235×178×74

Controller Weight: 0.9 Kg

DriveUnitDimensions(L×W×H):245×100×95 (mm)

DriveUnitWeight:3Kg

IP Rating: IP41

>

≤

±

Of 30% of max. Infusion distance

≥

Output control: start/stop, direction (OC gate)

≤

℃

Relative humidity ‹ 80 %

23 24

BaodingLongerPrecisionPumpCo.,Ltd

ADD: Building A,Chuangye Center Baoding

National High - Tech Industrial Development Zone

Baoding, Hebei, China 071051

TEL: 86 - 312 - 3110087 3138553

FAX: 86 - 312 - 3168553

E - mail: [e-mail]

Http:www.longerpump.com

SYRINGE PUMP

OPERATING MANUAL

TS-1A/L0107-1A
TS-2A/L0107-2A
TS-1B/W0109-1B

Baoding Longer Precision Pump Co., Ltd.

Longer Syringe Pump Operating Manual