Sawyer
Changing Table
Adaptable as Your Child Grows Up
Assembly Instruction Manual
Questions? Call Us at 1-800-515-4056
Website: www.lollyandme.com
Adult assembly required due to the presence of small parts, sharp points & sharp edges.
Before assembly, read these instructions. Make sure all pre-assembled parts are tight. Store this instruction manual for future reference.
Our goal is to improve the assembly process for the customer. If you have any questions during assembly or you are missing parts, please contact us
directly. Do not return product parts to the retailer before contacting our customer service department for assistance.
Please follow contact instructions on page 7.
2011 Made in China
Changing Table Warnings
Failure to follow these warnings and the assembly instructions could
result in serious injury or death.
• Read all instructions before use of changing table. KEEP INSTRUCTION FOR FUTURE USE. DO NOT USE
THIS UNIT IF THE INSTRUCTIONS CANNOT BE STRICTLY FOLLOWED.
• Before each usage or assembly, inspect unit for damaged hardware, loose joints, loose bolts and other
fasteners, missing parts, or sharp edges. DO NOT use unit if any parts are missing, or broken. Ask your
dealer or call LOLLY & ME at 1-800-515-4056 or write to 10301 Bren Road West, #0-379 Minnetonka,
MN 55343 replacement parts and instructional literature, if needed. DO NOT substitute parts.
• FALL HAZARD - To prevent death or serious injury, always keep child within arm’s reach.
• Periodically check all bolts and screws to maintain the stability of your changing table.
• Serious or fatal crushing injuries can occur from furniture tip-over. To help prevent tip-over:
• Be sure to use the wall strap kit to help reduce the risk of tip-over.
• Use of the wall strap kit may only reduce, but not eliminate, the risk of tip-over.
• DO NOT overload the shelves.
• Never allow children to climb or hang on shelves.
• Assemble on soft surface to prevent damage to the product finish.
• To make it easier to build your changer have a friend help during the assembly.
• Ensure that all parts and components are located before beginning assembly.
• Do not use the changing table if it is damaged or broken.
• Maximum weight of child: 30 lbs (13.6 kg)
2
Congratulations on Your Purchase!
Thank you for choosing a Lolly & Me product. Don’t worry
about the assembly. Inside you will nd understandable step-
by-step instructions with clear illustrations—it’ll be a piece of
cake! If you get stuck, ring us up at 1-800-515-4056. Need a
replacement part or is a part missing? Just call us and we’ll get
one sent o to you right away.
Remember to complete your product registration card and
mail it in to activate your product’s one year limited warranty.
You can also go online to www.lollyandme.com and complete
it there. Then—and this is the good part— you will be
registered in our quarterly drawing for prizes that will look
great in your little one’s nursery!
Sincerely, Lolly & Me
Questions? Call Us at 1-800-515-4056
Website: www.lollyandme.com
Email: customerservice@lollyandme.com
3
Instructions for Assembly
Sawyer
Changing Table
Adaptable as Your Child Grows Up
OK
Let’s Put This Baby
Together!
4
Parts List
Left End (x1) Right End (x1)
C D
Changing Table (x1)
BA
Back Panel (x1)
E F
G
Front Panel (x1)
Shelf Support (x4)
Shelf (x2)
5
Hardware
aa bb
cc
40mm Bolt (x12) Dowels (x14)
Wall Strap Kit (x1)
“L” Allen Wrench
6
STOP
IF YOU EXPERIENCE ANY
ISSUES WITH THIS PRODUCT
BEFORE YOU
RETURN THIS TO
THE RETAILER
PLEASE FOLLOW THE
PROCEDURES LISTED ON
THE FOLLOWING PAGE
7
PRODUCT ASSISTANCE PROCEDURES
IF YOU HAVE ANY QUESTIONS DURING ASSEMBLY OR YOU ARE MISSING PARTS, PLEASE
CONTACT US DIRECTLY.
PROCEDURES TO FOLLOW SHOULD YOU HAVE ANY QUESTIONS:
FOR THE BEST AND MOST TIMELY SERVICE PLEASE CONTACT US VIA EMAIL:
customerservice@lollyandme.com.
PHONE US AT: 1-800-515-4056 or write to 10301 Bren Road West, # 0-379 Minnetonka, MN 55343.
PLEASE PROVIDE THE FOLLOWING INFORMATION IN YOUR EMAIL:
1. YOUR NAME
2. ADDRESS
3. BEST DAY TIME PHONE NUMBER
4. PLACE AT DATE OF PURCHASE
5. MODEL NUMBER, NAME AND COLOR OF YOUR PRODUCT
6. MANUFACTURER’S CODE (THE MANUFACTURER’S CODE CAN BE FOUND ON A LABEL AFIXED TO THE
BOX AS WELL AS A LABEL AFIXED TO THE CHANGER ITSELF).
7. SHORT DESCRIPTION OF THE ISSUES AND ATTACHED PHOTOS IF POSSIBLE. PLEASE INCLUDE SPECIFIC PART NUMBERS IN QUESTION FOR MORE EFFICIENT SERVICE.
SOMEONE WILL CONTACT YOU VIA EMAIL OR PHONE TO HELP YOU WITH YOUR ISSUES.
IF YOU DO NOT HAVE INTERNET ACCESS, PLEASE FAX THE ABOVE INFORMATION TO: 612-573-6678.
IF YOU DO NOT HAVE INTERNET OR FAX ACCESS, PLEASE CALL US AT 1-800-515-4056 AND BE SURE TO HAVE
ALL THE ABOVE INFORMATION TO GIVE TO THE CUSTOMER SERVICE REPRESENTATIVE.
WE ARE HERE FOR YOU!
8
Parts Needed:
“L” Allen Wrench
OR
“S” Allen Wrench
A D E
Left End (x1)
Back Panel (x1)
Front Panel (x1)
aa bb G
40mm Bolt (x6)
Dowels (x7)
1 Changing Table Assembly
D
aa
A
Shelf Support (x4)
E
Attach Front Panel (E), Back Panel (D) and Shelf Supports (G) to the Left
End (A) using 6 Bolts (aa) and 7 Dowels (bb) as shown.
Continue to Step 2
G
bb
9
Parts Needed:
F C
Shelf (x2)
2 Changing Table Assembly
C
Changing Table (x1)
F
F
Slide Changing Table (C) into the Front and Back Panel and 2 Shelves
(F) into Shelf Supports as shown.
Continue to Step 3
10
Parts Needed:
“L” Allen Wrench
OR
“S” Allen Wrench
aa
40mm Bolt (x6)
B
Right End (x1)
bb
Dowels (x7)
3 Changing Table Assembly
B
aa
bb
Attach Right End (B) to Panels and Rails, using 6 Bolts (aa) and
7 Dowels (bb) as shown.
Continue to Step 4
11
Parts Needed:
4 Changing Table Assembly
Changing Table assembly complete.
Continue to Step 5
12
Parts Needed:
cc
Wall Strap Kit (x1)
5 Changing Table Assembly
To prevent death, serious injury from Changing Table tipping over, the
Wall Strap Kit MUST be used and attached properly to Changing Table
1. Firmly attach Wall Strap to the back of Changing Table.
2. Attach other end of Wall Strap to the wall.
Refer to the instructions in the Wall Strap Kit for securing Changing Table
to the wall.
WALL
13
Disassembling Changing Table for Storage
To disassemble Changing Table for storage, follow steps in reverse.
Store all parts and hardware together in a safe place. Store the instruction manual for future reference and
for reassembly.
Cleaning and Maintenance
To clean Changing Table, use only mild household soap and warm water. Do not use bleach or detergent.
Do not use abrasive cleaners which can scratch the nish of the Changing Table. Use clean soft cloths to
wash, rinse and dry. With proper care, the quality nish will last a long time. Wood surfaces may be treated
with a light application of a good grade non-toxic furniture polish.
14
Done!
Pat Yourself on the
Back ... Good Job!
10301 Bren Road West, Suite #0-379
Minnetonka, MN 55343
1-800-515-4056
Website: www.lollyandme.com
Email: customerservice@lollyandme.com
15
If a part is missing or you have questions, contact us.
E-mail: customerservice@lollyandme.com
1-800-515-4056
Loading...