CREINA d.d, Mirka Vadnova 8, 4000 KRANJ
Tel.: 04 20 13 350, Fax: 04 20 13 363, E-mail: INFO@CREINA.SI
www. lokaterm.com, www.creina.si
Users manual
Installation, Operating and Maintenance Instructions
CABANO
User Manual
Installation, Operating and Maintenance Instructions Stove Cabano
Contents
1. MANUFACTURER / PRODUCT TYPE............................................................................................................ 3
2. USER MANUAL............................................................................................................................................... 5
2.1 STOVE DESCRIPTION................................................................................................................................. 6
2.2 INITIAL IGNITION.......................................................................................................................................... 7
2.3 LOADING FIREWOOD.................................................................................................................................. 7
2.4 CLEANING OF THE STOVE......................................................................................................................... 8
2.5 BREAKDOWNS AND CAUSES..................................................................................................................... 8
3. MOUNTING INSTRUCTIONS......................................................................................................................... 9
4. TRANSPORT................................................................................................................................................. 10
5. INSTALATION INSTRUCTIONS................................................................................................................... 10
6. WARRANTY.................................................................................................................................................. 11
Lokaterm November-2015 page 2
User Manual
Installation, Operating and Maintenance Instructions Stove Cabano
1. MANUFACTURER / PRODUCT TYPE
LOKATERM Tel.: +386 (0)4 20 13 350
Creina d.d. Fax: +386 (0)4 20 13 363
Ulica Mirka Vadnova 8 E-mail: info@creina.si
4000 Kranj / SLOVENIJA Website: www.lokater m.com
Technical data
Figure 1: Dimensions of the stove Cabano
Lokaterm November-2015 page 3
Product Type Cabano
Standard: EN 13240
Smoke outlet diameter: Ø 148 mm
Nominal thermal power: 6 kW
Efficiency: 73 %
CO – emissions (13% O2) 1250 mg/m
3
Dust emissions 40 mg/m
3
Exhaust smoke temperature: 299 °C
Exhaust smoke volume: 7,7 g/s
Flue draught at nominal power 12 Pa
Outdoor air intake: Ø 100 mm
Dry weight: 130 kg / 220 kg
Dimensions of the stove Dia x Height 806 mm x 1041 mm x 508 mm
Safety disatance Sides and back 400 mm / front 1250 mm
User Manual
Installation, Operating and Maintenance Instructions Stove Cabano
2. USER MANUAL
Congratulation on your purchase of LOKATERM stove. Please take some time and read this sheet carefully.
For stove to work properly and to have a valid warranty claim, please follow the recommendations and guidelines
gathered in this sheet.
In case you have additional questions that are not covered in this sheet please contact your local stove supplier or
stove service.
Proper use and maintenance are prerequisites for stove to work long and flawlessly.
Delivery check
First of all, check the stove for possible defects and damages. Pay special attention to both stove glass and firedoor.
After first use of the stove, most common defects on the glass are caused by improper handling or heat overload.
Before installation, check the functionality of all the movable parts. For possible defects contact your local supplier.
Safety measurements
Warning! Heated metal parts and heated glass can cause burns, therefore, when handling the stove always use
enclosed protection gloves.
Take special precaution when children are around.
Fireprotection safety inside radiation area
Minimum distance from firebox opening to nearest combustible element (ex. furniture elements, alcohol brewages),
should be greater than 80 cm.
Fireprotection safety outside radiation area
Do not put any combustible objects within a 50 cm distance from the open stove.
Suitable fuels
Stove is suitable for burning natural firewood (ex. beech, birch), wood briquettes and briquettes made of brown coal.
Emission limitation
It is forbidden to burn the following materials in stoves:
Impregnated or moist wood, wood chips, materials of organic origins (hooves, horns etc.), coal dust, plastic waste or
household waste, paper and cardboard (with exception when igniting fire).
Please note, that burning any kind of waste, is hazardous to both your health as it causes environmental pollution. It
also damages your stove and thus shortens its lifespan.
Stove fires are dangerous
Dumping waste into stoves and burning it is not only a health or environmental issue, but also a fire-protection
problem. In general, if stove is not handled properly (cleaning it regularly, burning appropriate materials etc.), it is
prone to fires.
If fires were caused by the stove, as a result of improper use, user can be held legally responsible.
Warnings
Stoves are not permitted to be walled up or modified (adding/removing material). Air supply and its regulation (air-inlet
system), must not be tampered with. Furthermore, continues air supply, for stove to work properly, must be
guaranteed. Whenever you work with hot stove, use the enclosed protection gloves, to prevent possible burns.
For ignition, never use gasoline, alcohol or similar substances.
Don't overload the stove with firewood (max. 2-3 pieces of wood when igniting and max. 2.5 kg/h when continuously
burning).
Always use the prescribed fuel and don't thermally overload the stove (max. heat output). This is important for the
warranty to remain valid.
All possible damaged parts should be replaced before first lightning of the stove.
Lokaterm November-2015 page 4
User Manual
Installation, Operating and Maintenance Instructions Stove Cabano
2.1 STOVE DESCRIPTION
Stove is made primarily of sheet metal and has a closed combustion chamber.
Stove can be placed anywhere in the room (along the wall, in the corner etc.), as long as ground is flat. No
concession is needed for the stove installation.
Increased functionality with simplified regulation
When stove is operating, a layer of ember is formed in combustion chamber, which assures an even burning out of
firewood. By regulating the opening of the air-inlets, one can indirectly control the heat output of the stove.
Lokaterm one-hand regulation (LER)
LER allows easy one-hand regulation of the quantity and distribution of combustion air. If you choose to connect an
external fresh air system LER provides complete tightness and independence of the stove from the room air.
Lokaterm stoves that are equipped with LER are therefore suitable for installation in buildings with forced ventilation.
Lever LER is located under the fire chamber door.
The lever has a central zone for normal operation and two extreme positions:
- Heating-up position (fully open air inlet under the ashtray - primary air).
The handle is moved to the left extreme. In the last part of the stroke, it is necessary to slightly raise the lever – on
the step for the activation of the primary air. The lever must be in this position only during the heating-up of the stove approximately the first 10 minutes of burning.
- Normal operation area (only the air inlet above the door is open - secondary air). This is an area within which the
stove can be continuously used and the power can be regulated. The handle may be located in any position, but not
in the heating-up position.
- Closed position of the air inlet (LER lever is moved to the extreme right). The lever is in this position only when the
stove is not in use.
Figure 2: Combustion air regulation lever - LER
Warning
Continuous use of the stove, with a LER handle in heating-up position may overheat the stove, leading to
damage of the exposed parts.
Using the stove at the fully closed air supply (LER lever is moved to the extreme right) is not allowed.
Lokaterm automatic doors (LAV)
Lokaterm automatic doors (LAV) enshure automatically closing and sealing quality throughout the life of the stove.
LAV have a fix, hollow and air-cooled handle, which serves to open the door. Closing is done automatically with the
help of the built-in mechanism, or by manual applyance of a slight force. Doors have a snap closing mechanism,
which snaps the doors in the totally open position, and starts closing when the snap is released.
Lokaterm clean glass (LCS) is a system that ensures that you can observe the magic of the burning process
through the clean glass. The hot air enters on the top inner side of the glass and then flows through the glass down,
and thereby deterred the flue gases from the glass.
Lokaterm November-2015 page 5
Normal operation area
Heating-up position
User Manual
Installation, Operating and Maintenance Instructions Stove Cabano
2.2 INITIAL IGNITION
Empty ash-pan and combustion chamber.
First ignition of the stove should be performed in company of authorized person.
Start with low intensive fire. All materials must be gradually exposed to heat to prevent potential firebrick cracks,
coating damages and damages of material (bending).
Ventilate the room thoroughly. Any scent which may appear, when protection coating is being hardened, will
eventually diminish (when sufficient temperature in stove is reached).
Ignition procedure
Set the regulator to the ''Heating-up'' position
Open the fire door.
After you have put in several ignition material (thin wood, ignition cubes, scrambled paper…) into combustion
chamber, insert 2-3 pieces of firewood (chopped) on top of it. Please fill stove with care to avoid potential
damage.
Ignite the ignition material and close the fire door.
After the stove heats up (it usually takes up from 5 to 10 minutes), set the regulator to ''Full power'' or to
''Reducerd power'' position.
The “Heating-up position“ may only be used for heating up. If used permanent, there is a hazard of overheating and
damaging of the stove and is strictly prohibited.
Nominal heat output (6 kW), is generated when the regulator is set to ''Medium power'' position and there is aprox.
2,5 kg of firewood inside of stove and the draught is at 12 Pa.
Some of the air, which is heated up inside of stove, is guided through the channels inside the stove, onto the fire door
glass, where it performs a cleaning (of the glass) (air brush cleaning principle).
Attention:
Certain types of stoves require somewhat longer ignition phase, until there is enough negative pressure (draught) for
the stove to work on its own. When this is the case, use smaller, dried-up logs. Afterwards you can use bigger logs.
If fire door is open during ignition phase, strong draught can cause fire to blaze up. High flames start to pound the fire
door glass, thus sooting it or even damaging it.
Heating
Maximum capacity of the stove is 2,5 kg of firewood per hour.
Leave the fresh air connection flap open.
Regulate the fire intensity with the LER lever. Set the regulator to one of the power positions.
2.3 LOADING FIREWOOD
Fully open flue-damper (is present).
When opening fire door, always use the enclosed protection gloves.
Open door slowly.
Remember that maximum capacity is 2,5 kg of firewood per hour.
Close the fire door.
Close the flue-damper (if present) to its operating position.
Always keep the fire under control, to prevent possible fire accidents. Pay special attention if children are
around.
Lokaterm November-2015 page 6
User Manual
Installation, Operating and Maintenance Instructions Stove Cabano
2.4 CLEANING OF THE STOVE
Warnings
Never use water for fire extinction.
Cleaning should only be performed when stove is fully cooled down. Remember - embers could remain in
ashes, hours after the fire has been extinguished.
When cleaning, always wear protection gloves.
Open the fire door
Remove debris from combustion chamber.
Glass should be cleaned with special cleaning agent. (Contact your local stove-supplier, regarding those
cleaning agents).
If stove is being used properly, stove glass should remain clean (There is always a possibility that not all of
conditions, for stove to work properly, were met (some of the firewood might be wet, chimney conditions not
perfect etc.), therefore glass might still soot up.
2.5 BREAKDOWNS AND CAUSES
What if,...
... the fire extinguish itself, or lights up poorly?
Is the flue-damper opened (if present)?
Is the fresh air-inlet flap opened?
Is the air regulator handle opened?
Is the fresh air supply sufficient?
Is the firewood dry?
… the stove doesn't heat up?
Is the air regulation handle in opened position?
… the stove is overheating?
Is the air regulation handle in the heating up position?
... the glass quickly becomes too sooty?
Firewood has to high moisture content.
Flue-damper wasn't open enough.
The air regulation handle wasn't in the right position
... the door locking mechanism closes accidentaly?
Pull the loch with the supplied pulling hook – see Figure.
Note
Take into consideration, that ventilation hood, which operates in same or nearby room, creates negative pressure,
which can cause smoke to leak into the room instead through chimney.
Ventilation hood also deprives stove of fresh air, therefore, take care that stove has enough fresh air to operate
normally. .
Warnings
Only qualified and trained personnel are allowed to perform repairs on the stove. By reading this manual one does
not become such an expert. If problems, similar to those mentioned above, arise, please contact your local stoveservice or chimney-sweeper.
Lokaterm November-2015 page 7
User Manual
Installation, Operating and Maintenance Instructions Stove Cabano
3. MOUNTING INSTRUCTIONS
Foreword
Please read these instructions carefully and pay attention to advices, especially to those for safe handling.
Before you start with the installation of the stove, check:
If all parts are included (Notify supplier if any of the parts are missing)
The stove for potential damages (pay special attention to glass, firedoor and coating protection; Notify hauler,
if damages are found)
The functionality of all the movable parts
This manual is not a service handbook. Here you won't find any instructions on how to repair the stove.
Regulations
Following regulations and standards have to be followed:
EN 13240
State building regulations and provisions.
Fire-protection provisions.
All other European, national and local regulations and provisions that deal with installation of the stove.
Basic requirements
Stove can be installed if:
Installation area is big enough to ensure normal use (operating, cleaning …) of the stove.
Within radiation area of the stove, there are no load-bearing construction elements (ex. pillars).
Sufficient air supply is secured.
There is a direct or indirect air connection with another room.
Stove must not be installed:
In rooms, where highly inflammable and explosive substances or their mixtures are being manufactured,
processed or stored.
In rooms that are ventilated and not have safety devices that prevent negative pressure.
In rooms that have no adequate air supply for stove to work properly.
Installation requirements:
Stove has to be installed in a way, that connection parts (chimney flue, air conduit), when needed of cleaning,
are easily accessible.
Walls in installation area of the stove, must be free of electrical and gas installations.
Air combustion conduit:
Air connection for additional air supply to the room, where stove will be installed, has to have a cross-section
of at least 100 cm2.
When calculating the necessary air conduit cross-section, local (elbows, filters etc.) and line (conduit length)
resistances have to be taken into consideration.
When air travels through operating combustion chamber, it heats up.
Air conduit's overflow resistance must not exceed 4 Pa.
Floor protection:
If floor, where stove will be located, is not fire resistant, it has to be protected by a layer of fire-resistant
material (ex. 6 mm thick glass plate).
Incombustible floor area in front of the stove has to be at least 50 cm long, while on the sides the distance
must not be less then 40 cm. (measured from stove walls)
Fire-protection distances:
Minimum distance between charging door and combustible objects must be at least 80 cm, while for sideplates; the
distance must be greater then 40 cm.
Lokaterm November-2015 page 8
User Manual
Installation, Operating and Maintenance Instructions Stove Cabano
Chimney
Effective height of the chimney should be at least 4 meters (measured from the hearth of the stove). For detailed
calculations, please refer to standard EN 13384-1.
4. TRANSPORT
Transport should be handled by experts with appropriate equipment.
Packaging
Stove is tightly fixed onto a palette.
Please check the stove for possible damages and that is contains all ordered parts.
If you do find any damages, please report them to your stove supplier immediately.
Handling of the stove
Stoves should be moved with a palette, standing upside-down. Move it carefully so it does not tip over!
Avoid shocks and vibrations.
Once in place, dismount it and proceed with the installation.
Cover of the stove is breakable. It must not be loaded.
5. INSTALATION INSTRUCTIONS
General (Air inlet is optional)
Please do not overload the stove.
All the packing material should be removed from hearth and ash pan.
Check out functionality of movable parts (front door etc.)
Build outer air flaps into facade
Mount smoke flap onto chimney funnel
Connect chimney funnel. Chimney thickness and insulation must be in accordance with country's and EU
construction regulations.
Chimney must not apply additional pressure on the stove.
Minimum diameter of the chimney should be taken into consideration.
Measured values, gathered in this document, corresponds to the calculations of chimney with the following
dimensions - 4 m height; diameter 150 mm.
Air supply connection
For stove to work properly, continuous air supply is required.
If upper requirement is not met, additional air supply can be provided through air connection (Ø100mm)
which is located at the back of the stove.
Airflow is being regulated with air taps, which are built-in, into air supply conduit.
Please note that during winter times, cold air surges can generate condense on stove parts and thus
compromise its functionality.
Repair advice
Glass frame and most of the movable parts can be removed once the stove is installed.
Repairs can only be performed by a professional in agreement with the supplier/manufacturer
Repair instructions are not part of this document
if necessary, refer to your local dealer of service agent.
Lokaterm November-2015 page 9
User Manual
Installation, Operating and Maintenance Instructions Stove Cabano
6. WARRANTY
Lokaterm stoves:
are designed according to modern technical principles
comply with highest requirements from EN 13240 standard
are constructed from quality materials, that are under constant quality supervision
are handled with care during entire manufacturing process
are sophisticated technical devices, if installed correctly and according to installation specification
Usual wear can be:
changes of coating colour, due to overheat exposure.
changes of glass surface (ex. soot cover)
changes on firebrick (colour, small surface incisions)
stiffened sealings, due to heat
Warranty does not cover stove damages that occurred due to:
improper use
inappropriate maintenance;
not following recommendations given in both installation and operational manual
General warranty conditions
For flawless material, professional construction, manufacturing and safe functionality of this stove, we are
issuing a 2-year warranty!
We declare that:
The product will operate faultlessly, if you handle it according to the instructions;
We will repair any damages or defects on your demand, submitted within the warranty period;
We will replace any parts that could not be repaired with new ones in the warranty period.
The manufacturer obliges himself to repair any defects within 45 days from the reporting day at the latest.
The warranty does not cover :
Damages during transport and assembly,
Damages and defects on the product and in the vicinity due to incorrect connection of the stove to the
chimney,
Damages on the product, if the use has not complied with manufacturer’s instructions,
Damages and defects caused due to mechanical damages if the purchaser bears the guilt for them,
Damages of paint caused during neglectful cleaning,
Damages of stove, caused by water spills, food spills etc.
Parts that are in direct contact with fire (for ex. air brush, firebricks, grid, seals, etc.) -“spiderweb” effect
crated on glazed surfaces hidden damages inside of materials (stone, glass, ceramics etc.)
The warranty period commences from the date the stove is purchased. Date of purchase can be proven by
presenting the original bill. When claiming the warranty please state the model type and its factory number (located
on sticker, on back of the stove).
Warranty service is handled by a trained professional, who repairs or replaces compromised components free of
charge. If necessary whole stove can be replaced.
Repair specialist decides, whether or not the stove can be repaired on site or has to be taken back to repairshop.
Usually it is performed on location (where the stove is installed).
If warranty is not justifiable, all expenses generated by a claim, are covered by the customer.
Lokaterm November-2015 page 10
Loading...