Lojer SALLI, SALLI F3, SALLI F1, SALLI H2, SALLI F2 Operating Instructions Manual

SALLI Hospital beds
F1,F2,F3,H2,H4
Operating instructions

Version 1.3 04.09.2015

Operation instructions for Salli F1, F2, F3, H2 and H4 Hospital bed / Version 1.3

Limited International Warranty

The warranty period is determined in the agreement documents. Unless otherwise agreed, the warranty
period for manufacturing and material defects is 2 years, except the steel structure and welds which carry
a warranty of 10 years. For wearing parts (like upholsteries, batteries, ropes/wires) the warranty is 1 year.

Warranty Conditions

The warranty is only valid if the warranty demand is presented together with the original invoice or sales
slip or (order) confirmation, and the serial number on the product has not been defaced.
LOJER’s obligations are limited to the repair or, at its discretion, replacement of the product or the
defective part. Defective parts shall be replaced with new or equivalent “as new” parts. If necessary, the
entire product shall be exchanged with an identical or functionally identical product. The value of the
warranty service is always limited to the value of the defective product. The defective parts removed from a
product as part of a warranty case shall become the property of LOJER and shall be retained for by the
End Customer for LOJER, if necessary. If these parts cannot be returned to LOJER upon request, LOJER
is entitled to charge for a corresponding amount. When genuine LOJER parts are installed in a LOJER
product under warranty, only the remaining warranty period of the repaired device applies.
Warranty repairs must be carried out by LOJER or authorised LOJER Dealers. No re-imbursement will be
made for repairs carried out by a non-LOJER representative, and any such repair work or damage to the
products caused by such repair work will not be covered by this warranty

The product is designed and manufactured to meet the requirements for CE-marking. This product is not
considered to be defective in materials nor workmanship if it requires adaptation in order to conform to
other local or national technical or safety standards.

This warranty covers none of the following:
a) Periodic checks, maintenance and repair or replacement of parts due to normal wear and tear (such as
upholsteries, cables, ropes or reduced capacity of accumulators);
b) Costs relating to transport, removal or installation of the product;
c) Misuse, including the failure to use this product for its normal purposes or incorrect installation;
d) Damage caused by lightning, water, fire, acts of God, natural catastrophes, war, public disturbances,
incorrect mains voltage or any other cause beyond the control of Lojer;
e) Spillage of chemicals or liquids, or use of any other hazardous or non-instructed substances, which may
affect the product;
f) Minor defects or deviations from the product specifications which are immaterial, negligible or trivial as
regards to the value or the functioning of the product

.

Proceeding in a Warranty Case

The following information is an explanation of what you must do in the case of a warranty claim. First,
please contact your LOJER dealer and describe the problem (possibly with photographs or videos) and
inform LOJER of the product type and serial number. LOJER’s technicians will help to diagnose defects
and malfunctions, and are often capable of eliminating the malfunction over the phone.
In the event that warranty service is required, you should return the product to the dealer from whom it was
purchased, or directly to LOJER’s factory in Finland. In this case, the customer is responsible for the
dispatch and insurance of the product, and the transport and insurance costs shall be borne by the
customer. LOJER shall assume the costs for the materials / spare parts and the labour costs as required,
as well as the standard return transportation to the sender. In case of difficulty, details of local dealers are
available online at www.lojer.com. You may also contact the service centre in Finland (e-mail:
[e-mail]).

The guarantee will become void if:

• A Lojer product is equipped or used with parts that have not been approved by Lojer for the
product in question;

• Someone other than a person authorised by Lojer has serviced/repaired or otherwise modified the
device and these measures have caused a fault in the product;

• The product is cleaned with cleaning agents other than those specified in the operating manual, or
if the product is allowed to come into direct contact with agents other than those specified in the
manual;

• Regular maintenance has not been performed.

Copyright © Lojer Oy, 2010

Operation instructions for Salli F1, F2, F3, H2 and H4 Hospital bed / Version 1.3

Content

1 Salli hospital bed ..................................................................................................... 1

2 Salli hospital bed parts ........................................................................................... 1

2.1 Salli H-model bed parts ...................................................................................... 1

2.2 Salli F-model bed parts ...................................................................................... 2

2.3 Options and accessories .................................................................................... 2

3 Safety precautions .................................................................................................. 3

4 Measures to be taken before use ........................................................................... 4

5 Use of the hospital bed and accessories .............................................................. 5

5.1 Locking of the castors ........................................................................................ 5

5.2 Mattress platform height adjustment .................................................................. 7

5.3 Adjustment of the backrest ................................................................................. 8

5.4 Adjustment of the upper and lower leg section ................................................... 8

5.5 Trendelenburg adjustment ................................................................................. 9

5.6 Bed end attachment ........................................................................................... 9

5.7 Bed side rail ..................................................................................................... 10

5.7.1

Bed side rail, normal model (1332SKKP) .................................................. 10

5.7.2

Raised side rails ( 1332SKKPKOR ) ......................................................... 12

5.7.3

Eco model side rails (1332KSKP, 70524KP) ............................................ 13

5.8 Installation of the lifting pole (101910) .............................................................. 14

5.9 Installation of the lift support (lift support 80/90 ru) ........................................... 14

5.10 Installation of the IV-pole (60121 or 60122) ..................................................... 16

5.11 Urine bag holder ............................................................................................... 16

5.12 Short frame assembly to ease transport ........................................................... 17

6 Cleaning and disinfection ..................................................................................... 18

6.1 Detachment of the sleeping platforms .............................................................. 18

7 Service .................................................................................................................... 19

7.1 User check operations ...................................................................................... 19

7.2 Annual service .................................................................................................. 19

7.3 Annual service schedule .................................................................................. 20

8 Fault detection ....................................................................................................... 21

9 Technical specifications ....................................................................................... 21

9.1 Data of the type plate and markings on the bed ............................................... 22

9.2 Standards used ................................................................................................ 24

10

Spare parts and diagrams ................................................................................. 24

11

Contact information and references ................................................................ 34

Copyright © Lojer Oy, 2010

Operation instructions for Salli F1, F2, F3, H2 and H4 Hospital bed / Version 1.3

1

2

4

5

7

6

3

8

1 Salli hospital bed

This document include instructions how to use Lojer’s SALLI hospital beds.
Salli hospital beds have been designed for institutional and hospital use for

adults and patients over 12 years of age and taller than 146cm.
In model Salli H2 (80/90) there is hydraulic adjustment function for regulating

the height and mechanical or gas spring assisted function for regulating the
backrest and as an option a gas spring assisted trendelenburg adjustment. In
model H4 (80/90) there is also a mechanical or gas spring assisted
adjustment for upper and lower knee leg section. Salli F1, F2 and F3 are fixed
height beds having only backrest and/or leg section adjustments with
mechanical or gas-spring assisted functionality.

IMPORTANT! Read instructions for use before using the hospital bed.

2 Salli hospital bed parts

2.1 Salli H-model bed parts

1 Bed rail, normal model (optional)
2 Backrest section
3 Upper leg section
4 Lower leg section
5 Central brake pedal
6
7
8
2+3+4

Trendelenburg adjustment handle (option)
Bed end
Handwheel for bed end attachment
Mattress platform (lying surface)

Figure 1. Salli H4, hospital bed

Copyright © Lojer Oy, 2015 1

Operation instructions for Salli F1, F2, F3, H2 and H4 Hospital bed / Version 1.3

1

3

7

2

6

5

5

4

8

2.2 Salli F-model bed parts

1 Bed rail, eco-model (optional)
2 Backrest section
3
4
5 Wheel brake, individual locking castors
6 Bed end
7
8
2+3+4

Upper leg section
Lower leg section

Bed end for eco side rails
Handwheel for bed end attachment
Mattress platform (lying surface)

Figure 2. Salli F3, fixed height hospital bed

2.3 Options and accessories

The hospital bed can be purchased with the following options:

• Bed ends and side rails with chromed or epoxy coated metal parts

• Different colour alternatives for the laminate plates of the bed ends

For Salli hospital bed the following accessories, which must be ordered
separately can be used:

• Bed rails, different versions; normal, raised and eco model

• Lifting pole, (101910)

• IV-pole, (60121, 60122)

• Lift support, (Lift support 80 ru or Lift support 90 ru)

• Food tray

• Urine bag holder

• Basket for accessories

Copyright © Lojer Oy, 2015 2

Operation instructions for Salli F1, F2, F3, H2 and H4 Hospital bed / Version 1.3

3 Safety precautions

Adhere to the following safety precautions.

IMPORTANT! It is only allowed to use accessories approved by the

manufacturer intended for the bed type in question.

IMPORTANT! The mattress must be in accordance with the manufacturer’s

instructions regarding the height and width.

IMPORTANT! The rescue sheet must be attached to the adjustable

sleeping platform. The rescue sheet must not be attached to
the bed frame or through the parts of the frame, risk of
patient entrapment and damaging mechanics.

IMPORTANT! It must be possible to raise and lower the bed rail in an

unimpeded way so that no external obstacle (mattress, its air
hoses, bed linen or other object) supports or wedges the rail
in the upper position without the securing of the latching
mechanism of the rail itself.

IMPORTANT! The functionality of the bed side rail lock mechanism must be

double-checked in connection with the rail elevation
adjustment. During use, always check that side rail will lock
in up position correctly.

IMPORTANT! Always lock the castors before patient is laid on bed.
IMPORTANT! Only a patient is allowed to be on the mattress platform while

the bed is being adjusted.

IMPORTANT! Do not sit or stand on either (outermost) end of bed, risk of

overbalance (Salli F-model beds). See chapter 9.1 markings
on the bed, figures 24 and 25.

IMPORTANT! The hospital bed must always be left in the lowest position in

order to minimise any risk of a patient falling from the bed.

IMPORTANT! Always ensure that there is nobody between the

mechanisms while the bed or bed rails are being adjusted
(danger of entrapment).

IMPORTANT! If there is a risk that the patient may fall from the bed. Bed

side rails must be kept at the highest position when the
patient is left without monitoring. (danger of falling off the bed
and increased entrapment risk when lift support is used)

IMPORTANT! If the bed or its accessories has a malfunction, it must be

removed from use immediately and be taken to a service.

Copyright © Lojer Oy, 2015 3

Operation instructions for Salli F1, F2, F3, H2 and H4 Hospital bed / Version 1.3

4 Measures to be taken before use

Check that the transport package is unbroken and no transport damages have
occurred. Remove all packing material from around the bed. Also remove
possible transport supports between mechanics.

All the parts mentioned in the dispatch note must be included in the delivery. If
a client detects any deficiencies regarding the delivery, contact immediately
the supplier.

Take the following measures before using the hospital bed.

IMPORTANT! Read the instructions for use and safety precautions before

using the hospital bed.

IMPORTANT! Keep the wheel brakes locked always when there is no need

to move bed and before patient is laid on the bed. This helps
to prevent falling accidents caused by unstable bed.

IMPORTANT! Ensure that there is sufficiently space around the bed and

both over and under the bed for the different functions and
mechanism.

IMPORTANT! Ensure that the side rails function properly and can be locked

in the upper position when/if needed.

Copyright © Lojer Oy, 2015 4

Operation instructions for Salli F1, F2, F3, H2 and H4 Hospital bed / Version 1.3

5 Use of the hospital bed and accessories

The hospital bed is intended to be used in normal, dry interior conditions. The
room temperature may vary between +10 and +40 °C and the moisture
between 30-75 %. The permissible storage temperature of the bed is between

-5 and +60 °C and the moisture of the storage space between 30 and 75 %.
This paragraph contains information about the installation and use of the

accessories of the hospital bed. Some of the accessories can be purchased
separately.

IMPORTANT! Always use accessories approved by the manufacturer!

5.1 Locking of the castors

If Salli hospital bed is equipped with castors, it can have either central locking
or individual locking castors.

With central locking castors, lock the castors by pressing the pedal at the foot
end of the hospital bed to the lowest position. In the middle position (pedal in
the horizontal position) castors can turn freely.

In the uppermost position pedal direction locks the castor to ease transport.
Lock and check the direction locking wheel by moving the headend of the
hospital bed sideways.

1 Castors locked (brake, red button down)
2 Castors turn freely (pedal in middle position)
3 Direction lock (green button down)

Figure 3. Locking of the central locking castors

Copyright © Lojer Oy, 2015 5

Operation instructions for Salli F1, F2, F3, H2 and H4 Hospital bed / Version 1.3

1

Salli hospital bed equipped with individually locking castors. Lock the castor
by pressing the pedal above wheel. When the pedals are in the uppermost
position, castors are free. Each castor must be locked individually.

2

1 Castor is free
2 Castor is locked, pedal down (brake on)

Figure 4. Individually locking castors

IMPORTANT! Always keep wheels locked when there is no need for

moving the bed. This helps to prevent falling accidents
caused by unstable bed.

IMPORTANT! Before moving the bed it is advisable to detach some of the

accessories to minimise the risk of collision if they are not
needed in time of transportation. Lifting pole, lift support, IV­pole etc. accessories which expands remarkably needed
space around hospital bed.

Copyright © Lojer Oy, 2015 6

Operation instructions for Salli F1, F2, F3, H2 and H4 Hospital bed / Version 1.3

5.2 Mattress platform height adjustment

Salli H hospital bed has hydraulic height adjustment. Mattress platform height
can be adjusted between 46-81 cm. F- models have fixed height 56cm with
125mm castors. Raise the mattress platform by pressing the pump actuating
foot pedal downward. Lower the platform by lifting up the foot pedal.

Pedal to lift lying surface

Raise pedal for lowering lying surface

Figure 5. Adjustment for the hydraulic height adjustment

IMPORTANT! Always take care that during mechanical movements of bed

there is nobody or anything between or under the bed
mechanics (danger of entrapment).

IMPORTANT! The hospital bed must always be left in the lowest position in

order to minimise any risk of a patient falling from the bed.

Copyright © Lojer Oy, 2015 7

Operation instructions for Salli F1, F2, F3, H2 and H4 Hospital bed / Version 1.3

5.3 Adjustment of the backrest

The backrest of the hospital bed can be regulated between 0-70°. Adjustment
is mechanical or gas spring assisted. With mechanical adjustment the back
rest can be lifted and lowered manually by hand moving the back rest
platform. With gas spring assisted adjustment the backrest can be regulated
by pressing the handle and adjust the backrest in desired position.

Figure 6. Potential hazard areas for hand/finger entrapment when

adjusting mattress platform, backrest, knee, foot section.

IMPORTANT! Always ensure that there is nobody or anything under the

bed or between parts of the mattress platform while the bed
mechanics is raised or lowered (danger of entrapment).

IMPORTANT! Always be careful when adjusting lying surface parts. Risk of

entrapment between mattress surface parts and side rail.
See figure 6.

5.4 Adjustment of the upper and lower leg section

Salli F3 and H4 hospital beds have either a mechanical or gas spring assisted
adjustment for the upper and lower leg section. Adjust the upper leg section in
the desired angle by lifting up from knee area (upper leg part) or in gas spring
assisted version by lifting the handle and raising by hand from knee area if
needed. Lowering is done manually (mechanical bed) or in the gas spring
assisted version by releasing the handle and at the same time pressing the
knee part downwards. Lower leg section can be adjusted desired angle
manually.

IMPORTANT! Always ensure that there is nobody or anything under the

bed or between parts of the mattress platform while the bed
mechanics is raised or lowered (danger of entrapment).

IMPORTANT! Always be careful when adjusting lying surface parts. Risk of

entrapment between mattress surface parts and side rail.
See figure 6.

Copyright © Lojer Oy, 2015 8

Operation instructions for Salli F1, F2, F3, H2 and H4 Hospital bed / Version 1.3

5.5 Trendelenburg adjustment

Salli hospital bed has as an option a trendelenburg adjustment, which
operates with a gas spring. Mattress platform tilts to the trendelenburg (12°) or
antitrendelenburg (6°) position. Platform can be tilted by raising lever in leg
end and when the mattress platform is in the desired angle, loosen the lever
and the platform remains in the desired position.

Figure 7. Trendelenburg adjustment

IMPORTANT! Always before chancing height of mattress platform

(hydraulic beds) adjust mattress platform to horizontal level.

IMPORTANT! When bed is in trendelenburg position do not leave patient

without supervision. Always after use level mattress platform
horizontal.

5.6 Bed end attachment

There are differences between bed ends according used side rail model. For
eco model rails there is attachment part for rail locking in bed end part. Also
with raised model side rail a higher bed end model is recommended.

Lift handle to adjust platform tilt

Bed end for eco model side rails.
Always locate in foot end of bed.

Normal bed end

.

Figure 8. Bed end models

Bed ends are attached with hand wheels screw. See figures 1 and 2. To
tighten bed end, turn clockwise, to remove bed end open anti-clockwise.

Copyright © Lojer Oy, 2015 9

Operation instructions for Salli F1, F2, F3, H2 and H4 Hospital bed / Version 1.3

5.7 Bed side rail

There are different bed side rail models available for Salli hospital beds. All
models are either factory installed or can be installed afterwards. All side rails
can be detached easily from bed if needed.

5.7.1 Bed side rail, normal model (1332SKKP)

The height of the side rail can be adjusted by raising the rail from the
uppermost pipe part of rail. The rail is locked in the desired position when you
hear a click. When you want to lower the rail, grab the uppermost pipe and
pull the handle in the end of the rail and you can lower the rail down.

Installation and detachment of the rail: The rails have been attached to the
bed frame by two spring locking knobs underneath upper frame. When you
detach the rails, pull the knob downward and simultaneously pull the rail away
from the bed. When you install the rail, pull the locking knob down and press
the rail in place. Make sure when installing that side rails are positioned
correctly, side rail release handle located in leg end of bed. Ensure that the
rails are locked in place, correctly installed and side rails are locking in
adjustment positions.

Recommended mattress height with normal model side rail is max. 13cm.

Locking knob, pull down to install or
remove side rail. After install, check that
knob is in up position for correct locking
function

Figure 9. Side rail attachment below upper frame

Copyright © Lojer Oy, 2015 10

Operation instructions for Salli F1, F2, F3, H2 and H4 Hospital bed / Version 1.3

IMPORTANT! Ensure that there is nobody or anything between the rails

when they are being adjusted. Ensure that you hear a click,
that the rail is locked in the upper position.

IMPORTANT! When a patient is being transported, lower the adjustments

of the sleeping platform and the bed to lowest positions and
lift the rails up to minimise a patient’s risk of falling.

IMPORTANT! Always use mattress size which has been defined by

manufacturer for combination of side rail / bed model.

IMPORTANT! A rail, which is in the middle or intermediate position will not

prevent a patient’s fall from the bed. Consequently, if a rail is
in the middle position, it does not meet the requirements of
standard IEC 60601-2-52 and the patient safety is
endangered.

Copyright © Lojer Oy, 2015 11

Operation instructions for Salli F1, F2, F3, H2 and H4 Hospital bed / Version 1.3

5.7.2 Raised side rails ( 1332SKKPKOR )

Raised side rail functions are like side rail (1332SKKP). Install, detaching and
adjustment are similar as in 1332SKKP model. Raised side rail has a top part
with two positions to add patient safety when using air mattresses or thick
comfort mattresses.

Adjust the top part of the side rail by pulling locking knobs and turn it at the
same time. When the top part of the side rail is nearby of its available position
release locking knobs. Ensure the locking by moving the top part of the rails.
It will lock to the desired position when you hear a click from locking knob.

Recommended mattress height with raised model side rail is max. 22cm.

Figure 10. Locking knobs for rail part adjustment

IMPORTANT! Ensure that there is nobody or anything between the rails

when they are being adjusted. Ensure that you hear a click,
that the rail is locked in the upper position.

IMPORTANT! When a patient is being transported, lower the adjustments

of the sleeping platform and the bed to the lowest positions
and lift the rails up to minimise a patient’s risk of falling.

IMPORTANT! Always use mattress size which has been defined by

manufacturer for combination of side rail / bed model.

IMPORTANT! A bed rail, which is in the middle or intermediate position will

not prevent a patient’s fall from the bed. Consequently, if a
rail is in the middle position, it does not meet the
requirements of standard IEC 60601-2-52 and the patient
safety is endangered.

Copyright © Lojer Oy, 2015 12

Operation instructions for Salli F1, F2, F3, H2 and H4 Hospital bed / Version 1.3

5.7.3 Eco model side rails (1332KSKP, 70524KP)

There are two different models of eco rails available for Salli beds. Both
functions and are assembled same way, only difference is in dimensional
structure which allows 70524KP type to use thicker mattresses.

Installing of eco rails starts to attachment of front support underneath upper
frame. Raise backrest up position. Install front support so that it will line with
holes in upper frame and fix it with bolts. Notice white cap heading head end
of bed. Standard front system has bolt and nut fixing and it requires tools for
attachment. Quick release system is supplied with wingnuts and support plate
which can be attached by hands.

Align support along holes pattern, nut or support plate
inside frame side

Figure 11. Attachment of front support, quick release system

If foot bed end is not in place, put it into place but do not tighten it yet. Notice
extra parts in bed end for eco rails attachment pointing inward bed. Side rail
lock will be located into foot end of the bed. Slide rail into front support, notice
that plastic bearing for side rail is in place. Raise bed end in foot end a little bit
and slip rail into place and lower bed end into hole. Repeat on other side and
tighten bed end attachment. Check locking function of side rail.

Plastic bearing, both ends of bed

Side rail lock knob

Figure 12. Eco model rail assembly, head and foot end of bed

Recommended mattress height for 1332KSKP is maximum 13 cm and for
70524KP maximum 18 cm.

Copyright © Lojer Oy, 2015 13

Operation instructions for Salli F1, F2, F3, H2 and H4 Hospital bed / Version 1.3

IMPORTANT! Ensure that there is nobody or anything between the rails when

they are being adjusted. Ensure that you hear a click, that
the rail is locked in the upper position.

IMPORTANT! When a patient is being transported, lower the adjustments

of the sleeping platform and the bed to the lowest positions
and lift the rails up to minimise a patient’s risk of falling.

IMPORTANT! Always use mattress size which has been defined by

manufacturer for combination of side rail / bed model.

5.8 Installation of the lifting pole (101910)

Lifting pole can be used to help patient move or get up into a sitting position in
the bed. Install the pole in the sleeve at the head end of bed so that it is not
possible to turn pole sideways. You do not need any tools for the installation.

The pole is correctly installed, when the handle is hanging above the mattress
platform and the pole does not move sideways. The maximum safe working
load for the lifting pole is 75kg.

IMPORTANT! Before using the lifting pole, ensure that it is above the

sleeping platform and locked in a sideways position.

IMPORTANT! Check that there is sufficiently room above the bed. When

you lift the bed, the lifting pole also raises.

5.9 Installation of the lift support (lift support 80/90 ru)

1. Lift the rail and backrest up.

2. Open the wing nut on the clip plate in the frame.

3. Push the shaft of the support through the holes in the clip plates.

4. Turn the wing nut until it is tight.

5. Set the handle of the lift support in the hole of the support.

6. Turn the support to the desired direction.

If the lift support is correctly installed, there is sufficiently space for the rail to
move freely. Lift support can be used only along with normal side rails. When
eco side rails are in use, lift support is not available. Maximum safe working
load for side rails is 50 Kg.

Copyright © Lojer Oy, 2015 14

Operation instructions for Salli F1, F2, F3, H2 and H4 Hospital bed / Version 1.3

1

2

3

1 Location of the wing nut
2 Shaft of the lift support
3 Fastening of the thumb nut
4 Handle of the lift support

Lift backrest and side rail up

4

Figure 13. Installation of the lift support

IMPORTANT! Check that there is sufficiently room around the bed. When

you lift the bed the lift support also moves and the bed space
requirement also increases sideways.

IMPORTANT! If there is a risk that the patient may fall down from the bed

the ride rails has to be kept at the upper position when the
patient is left without monitoring. (danger of falling down and
of entrapment when lift support is used)

Copyright © Lojer Oy, 2015 15

Operation instructions for Salli F1, F2, F3, H2 and H4 Hospital bed / Version 1.3

5.10 Installation of the IV-pole (60121 or 60122)

Install the IV-pole in the collet in the head end of the hospital bed. The pole
locks in place when you turn it in collet. Remove IV-pole by pulling upward.
You can adjust height of IV-pole from adjustment collar in IV-pole. Maximum
safe working load for IV-pole is 2 kg.

Figure 14. IV-pole

IMPORTANT! Check that there is sufficiently room around the bed. When

you lift the bed the IV-pole also raises and space
requirement above increases.

5.11 Urine bag holder

Raise the backrest. Remove the short mattress platform ABS middle part
from the bed. The urine bag holder is fastened by pushing it through the
holes on the frame.

Figure 15. Urine bag holder

Copyright © Lojer Oy, 2015 16

Operation instructions for Salli F1, F2, F3, H2 and H4 Hospital bed / Version 1.3

5.12 Short frame assembly to ease transport

Salli GPM models have ability shorten the overall length of bed by removing
foot and head end part. Before shortening of bed remove side rails and other
accessories according instructions. Foot end part is taken out same way in all
models by opening hand wheel screws located in both side of frame and
removing bed end part.

Figure 16. Remove of end part and bed shorten to transport length

To remove head part, lift backrest up and remove head part by pulling out
from both locking knobs at the same time. Lift and pull head part apart from
upper frame. Installing is done in opposite way, push head part into matching
holes in upper frame and slide it downward until locking knobs will lock head
part in place. Secure that head part is completely locked and both locking
knobs are into locked position (pushed in).

Figure 17. How to remove head part

Copyright © Lojer Oy, 2015 17

Operation instructions for Salli F1, F2, F3, H2 and H4 Hospital bed / Version 1.3

6 Cleaning and disinfection

Clean and disinfect the metal parts of the hospital bed and the ABS plastic
plates with a moist cloth using a mild multipurpose detergent. Follow internal
instructions how often and how bed should be cleaned. Obey instructions
given by used detergent manufacturer. Recommended daily decontaminated
areas and parts are which patient or nurses are touching, side rails, bed ends
etc. accessories which are typically handled during patient treatment and
when using the bed. An overall cleaning is recommended every time when
bed is taken into use or when patient changes or at least once a week.

IMPORTANT! Do not clean the hospital bed with a water jet or

mechanically. NO MACHINE WASHING!

IMPORTANT! The disinfectant erodes the surface materials. Wipe the

disinfectant off with a moist cloth.

IMPORTANT! Do not use solvents like petrol or alcohol in the cleaning of

the hospital bed.

6.1 Detachment of the sleeping platforms

You can detach the ABS sleeping platform plates of the hospital bed for the
time of the cleaning. Backrest and foot section parts have Velcro tape
connections and can be removed simply by lifting from coroner of plate.

Detach the middle platform by lifting. When you put it back, check to set the
plate in the correct direction and proper place.

Head end
of the bed

Leg end of the bed

Figure 18. Normal layout of mattress platform ABS parts.

Copyright © Lojer Oy, 2015 18

Operation instructions for Salli F1, F2, F3, H2 and H4 Hospital bed / Version 1.3

7 Service

Need for service is minor but bed should be maintenance yearly period to
ensure safe and proper use. Bed expected service life is at least 10 years in
normal use if usage and service is done by manufacturer instructions. Please
notice that if manufacturer instructions from use and service are neglected it
may effect on service life expectation and may lead avoid product guarantee.
For correct disposal of the bed, follow given national instructions and laws
considering recycling metal, plastic etc. parts. Consult local dealer or
manufacturer if needed.

7.1 User check operations

Check the condition of the following parts every time when bed is taken into
use or when patient changes and recommended as a daily routine during
normal use:

• Bed rails, locking in highest position, stability

• Bed ends, attachment and stability

• Bed wheel brakes, check for stability and movement

• Check mattress platform adjustment, if and when adjustment is needed

The adjustment of the brakes and other service and repair operations are
instructed in a separate service manual and are meant to be done only by
professional service personality. If any abnormal behaviour is notice, bed must
be taken out of use at once and taken to service for repair.

IMPORTANT! If abnormal behaviour is noticed during normal use, bed

7.2 Annual service

The annual service operations are instructed to be done only by professional
service people according national laws and requirements. Every person who
is involved in service or maintenance should at least read the safety notices
and instructions for use to ensure that bed is working properly. Please take
notice following step before maintenance of the bed

should be taken out of use immediately. Do not use bed
which is broken or has a malfunction that might influence
patient and user safety.

• Bed should be cleaned and disinfected before and after repair/service work

• Read manuals and check for correct functionality of the bed mechanics

• Always repair or service only unoccupied beds

• Always make notice for done maintenance or repair work in service form

• Use only original spare parts which are proven by manufacturer

Copyright © Lojer Oy, 2015 19

Operation instructions for Salli F1, F2, F3, H2 and H4 Hospital bed / Version 1.3

7.3 Annual service schedule

Once a year bed should be inspected and serviced to guarantee a safety use
of bed. Annual service is mainly carried out by three stage program. Technical
and visual inspection, functional testing and some service tasks. Visual
inspection should be carried out to check following parts and functionalities in
bed.

• Check bed parts and components for any unusual marks, fragment, tear,
bending, unusual wearing, welding seam fractures etc.

• Check for any loosen component, loosen bolts, nuts, locking pins etc.

• Repair and replace broken parts if needed

Functional testing should be carried out for following systems.

• Check functionality of all adjustments and accessories, stability and proper
fixing, locking functions of systems, take notice for proper function

• Check functionality of side rail, proper locking, stability

• Check bed stability, individual wheel brakes, central brake lock

functionality, direction locking of wheel etc.

• Check adjustments for mattress platform, movement in all positions and
parts, gas spring and (Rastomat) mechanical adjustment

• Check functionality of trendelenburg if there is one (optional)

• Check functionality of accessories, lifting pole, lift support etc. (optional)

Service

• Lubricate bearings, friction points, hinge connection if you hear noise from
mechanical adjustments. Lubricate with normal or aerosol vaseline

• Check again done service work to ensure proper function of bed

• Fill out following annual service report like below. You find a copy in the

end of manual section 10 spare parts and diagram

Copyright © Lojer Oy, 2015 20

Operation instructions for Salli F1, F2, F3, H2 and H4 Hospital bed / Version 1.3

8 Fault detection

In order to purchase spare parts please contact the Lojer sales (please see
Chapter 14 Contact information). Before contacting us, please ensure that you
have the following information available:

• Product name and model

• Serial number

• Purchase year

• Accurate description of the problem.

The product name, model, serial number and manufacture date can be found
on the type plate (please see chapter 9.1, figure 16 Type plate) from lower
frame at the headend of the H-models and in the upper frame F-models.

More detailed service instructions can be found in the separate service
manual (please see Chapter 0 References).

9 Technical specifications

Width 80 cm or 90 cm
Total width 90 cm or 100 cm (with side rails)
Length 222 cm (177cm, short frame transport length)
Mattress measure 78 cm or 88 cm x 205 cm x 13 cm
Weight of a bed H-models 98-116 kg (depending width, accessories)

F-models 60-86 kg (depending width, accessories)
Safe Working Load 170 kg / 135 kg max. patient weight
Adjustment of height

Height of F-models
Transport temperature -5 - + 60 °C, moisture 30-75 %
Storage temperature -5 - + 60 °C, moisture 30-75 %
Operating temperature

46–81cm (125mm castors), 49-84cm (150mm castors)

56cm (125mm castors)

+10 - + 40 °C, moisture 30-75 %
Mattress size

Copyright © Lojer Oy, 2015 21

Width 78/88 cm (80/90 cm beds), length 205 cm,

normal height max. 13 cm, with raised rails 18 cm or 22

cm. See chapter 5.7

Operation instructions for Salli F1, F2, F3, H2 and H4 Hospital bed / Version 1.3

9.1 Data of the type plate and markings on the bed

CE A product meets the requirements of directive

93/42/EEC

Figure 19. Type plate,

The type plate is located at the front of the lower frame of the hospital bed H­models and in the upper frame side tube F models.

Figure 20. Warning for use or assembly of incompatible

Figure 21. Instructions for mattress specification

Figure 22. Safe working load: 1 max. patient weight, 2 safe working load

Copyright © Lojer Oy, 2015 22

Operation instructions for Salli F1, F2, F3, H2 and H4 Hospital bed / Version 1.3

Information marked with this symbol must always be read and

Figure 23. Warning about risk of crushing and entrapment

Figure 24. Warning, information must always be read and strictly adhered

to

Figure 25. Observe the information in instructions for use

Figure 26.

strictly observed

Figure 27. Warning notice on sitting/standing in the end of bed, hazard

area see figure below

Figure 28. Hazard area on mattress platform

Copyright © Lojer Oy, 2015 23

Operation instructions for Salli F1, F2, F3, H2 and H4 Hospital bed / Version 1.3

9.2 Standards used

Lojer Salli hospital beds meet the requirements of directive 93/42/ETY
(medical devices) and its amendments.

The following unified standards have been adapted in the design and testing
of the bed models:

• EN 60601-1: 2005

• EN 60601-2-52

10 Spare parts and diagrams

See following diagram for spare part order. Use diagram to find out needed part. For
ordering spare part check the serial number located in model/type plate in bed frame.
Don`t hesitate to take contact for consulting correct part, see contact information
chapter 11.

Copyright © Lojer Oy, 2015 24

Operation instructions for Salli F1, F2, F3, H2 and H4 Hospital bed / Version 1.3

Copyright © Lojer Oy, 2015 25

Operation instructions for Salli F1, F2, F3, H2 and H4 Hospital bed / Version 1.3

Copyright © Lojer Oy, 2015 26

Operation instructions for Salli F1, F2, F3, H2 and H4 Hospital bed / Version 1.3

Copyright © Lojer Oy, 2015 27

Operation instructions for Salli F1, F2, F3, H2 and H4 Hospital bed / Version 1.3

Copyright © Lojer Oy, 2015 28

Operation instructions for Salli F1, F2, F3, H2 and H4 Hospital bed / Version 1.3

Copyright © Lojer Oy, 2015 29

Operation instructions for Salli F1, F2, F3, H2 and H4 Hospital bed / Version 1.3

Copyright © Lojer Oy, 2015 30

Operation instructions for Salli F1, F2, F3, H2 and H4 Hospital bed / Version 1.3

Copyright © Lojer Oy, 2015 31

Operation instructions for Salli F1, F2, F3, H2 and H4 Hospital bed / Version 1.3

Copyright © Lojer Oy, 2015 32

Operation instructions for Salli F1, F2, F3, H2 and H4 Hospital bed / Version 1.3

Copyright © Lojer Oy, 2015 33

Operation instructions for Salli F1, F2, F3, H2 and H4 Hospital bed / Version 1.3

11 Contact information and references

Manufacturer

Lojer Oy
Putajantie 42
38210 Sastamala
Tel. [phone]
Fax. [phone]
Email: [e-mail]

www.lojer.com

Service

Tel. [phone]
Email: [e-mail]

www.lojer.com/huolto

Sales

Tel. [phone]
Email: [e-mail]

References

ScanAfia PRO S 2, S 4, TK 2 and TK 4 Hospital bed Service manual
Salli F,H and F/H GPM model quick instructions

Copyright © Lojer Oy, 2015 34