Logiware go1984 User Manual

Download

User manual

go1984

Alfred-Mozer-Str. 42

D-48527 Nordhorn

Germany

Telephone (+49)(0)5921 7139925

Telefax (+49)(0)5921 7139929

go1984

http://www.go1984.com

Alfred-Mozer-Str. 42

D-48527 Nordhorn

Germany

Telephone (+49)(0)5921 7139925

Telefax (+49)(0)5921 7139929

http://www.logiware.de

go1984 User manual

Table of Contents

................................................................................................................................... 105 Entering the license code

................................................................................................................................... 136 Basic setup

................................................................................................................................... 607 User management

................................................................................................................................... 628 Webserver

................................................................................................................................... 799 Image Center

................................................................................................................................... 8310 Additional settings

................................................................................................................................... 9111 Event management

................................................................................................................................... 9512 Appendix

................................................................................................................................... 9613 Masthead

Contents

................................................................................................................................... 11 Introduction

................................................................................................................................... 22 Editions

................................................................................................................................... 33 Installation

................................................................................................................................... 84 Launching the program

......................................................................................................................................................... 14Adding a camera

.................................................................................................................................................. 14IP camera

.................................................................................................................................................. 18PTZ camera

.................................................................................................................................................. 23Webcam (USB)

.................................................................................................................................................. 24Capture card

......................................................................................................................................................... 25Recording

.................................................................................................................................................. 28Calculating memory requirements

.................................................................................................................................................. 29Memory management

.................................................................................................................................................. 30Scene generation

.................................................................................................................................................. 31Pre-/Post alarm

.................................................................................................................................................. 32Access time period

.................................................................................................................................................. 33Export

......................................................................................................................................................... 34Motion detection

......................................................................................................................................................... 39Http event

......................................................................................................................................................... 45Notification

.................................................................................................................................................. 46Sound

.................................................................................................................................................. 47E-mail

.................................................................................................................................................. 48FTP

.................................................................................................................................................. 50LAN-Broadcast

.................................................................................................................................................. 54External program

.................................................................................................................................................. 55ISDN

......................................................................................................................................................... 56Scheduler

......................................................................................................................................................... 63Configuration

......................................................................................................................................................... 65Interface

......................................................................................................................................................... 68iPhone Client

......................................................................................................................................................... 70J2ME Client

......................................................................................................................................................... 73DynDNS

......................................................................................................................................................... 76Clustermode

......................................................................................................................................................... 83Camera

......................................................................................................................................................... 86Startup settings

......................................................................................................................................................... 87HTTP Proxy

......................................................................................................................................................... 88SMTP server configuration

......................................................................................................................................................... 90Translation

......................................................................................................................................................... 95POP3/SMTP-Server

go1984 User manual

Introduction

1 Introduction

go1984 is software designed for professional and hassle-free monitoring by closed circuit TV (CCTV). It sets a new benchmark in the industry: it is simple to use, packed with features and available at an affordable price.

go1984 features everything you'll ever need to carry out professional CCTV surveillance, including:

· Live monitoring

· Recording (timer-controlled, motion-triggered or permanent)

· Control of PTZ cameras

· Notification options: acoustic, by e-mail or by voice call via ISDN

· Remote access via network or the Internet

· Calendar functions

The software works as a so-called "hybrid system", which means it is capable of processing digital network cameras as well as analog video sources via video servers or capture cards. Companies with analog video technology can use the software to assist the "smart transition" to the digital world while integrating their existing hardware. go1984 thus makes an important contribution to protecting your investments.

go1984 supports the hardware of many well-known manufacturers such as, for instance: Axis, Sony, JVC, Panasonic, Mobotix, Logitech, Intellinet and many others.

The following figure illustrates the connectivity options provided by go1984:

2 Editions

go1984 is available in various editions. The following figure highlights the differences.

Editions

go1984 User manual

Installation

3 Installation

Installing go1984 is a matter of minutes even for users unfamiliar with the program. An unregistered version of the software can be tested for 30 days with all its functions. An uninstaller is included in the download so that you can remove go1984 immediately from your computer if you are not happy with the program.

To start the installation, click on the following icon:

First choose the language you want for the installation process.

You will now be taken step by step through the installation process for go1984. You can accept the default settings and continue in the installation process by clicking on the "Next >" button where applicable.

Installation

If you prefer to install to a different directory or hard-drive, please select the corresponding option in the following dialog.

Then select the components to be installed. You can choose the go1984 client as well as go1984 (see “

LAN Broadcast” section).

go1984 User manual

Installation

The installation routine will automatically create an entry labeled go1984 in your Windows start menu. If you prefer a different name, you can change it at this point.

All settings needed for the installation processes are now available. By clicking on the "Install" button, the installation will be completed and the required files will be copied to your hard-drive.

The installation of go1984 has now been completed. The installation routine is closed when you click on the "Finish" button. You can choose to have go1984 launched directly afterwards.

go1984 User manual

Installation

In the Enterprise edition go1984 can be installed as a service. To do this, you start the program on a one-off basis via the command line using the parameter "-install".

A message will appear indicating that the service has been successfully installed.

4 Launching the program

After installing go1984, there are various ways to launch it.

1. Launch using the Windows quick start bar

2. Launch using the desktop

Launching the program

3. Launch using the start menu

Select: Start à All Programs à go1984 à go1984

4. Autostart

If you want go1984 to be launched automatically when your computer is switched on, please activate the option shown in the following diagram. If you are going to run go1984 in service mode (see

"Installation" section), deactivate this option so that go1984 service will then be launched automatically.

go1984 User manual

Launching the program

Note:

Most Windows programs are shut down completely when you close the program window. go1984 is only hidden and continues to run in the background.

While the program is running, the go1984 symbol is displayed in the task bar near the time. You can use it to shut the program down completely or to bring it back to the foreground. Clicking on the icon with the right mouse key will open the corresponding menu.

Entering the license code

5 Entering the license code

go1984 runs as a demo version after being installed. In order to make go1984 function without any time or feature restrictions, you need to enter the activation data you purchased into the appropriate fields.

Please take care to transfer the data exactly as you received them by e-mail or on the license card. You will sometimes find a numerical input for the name or place in the activation data. If this is the case, enter the specified numerical sequence.

go1984 User manual

Entering the license code

If activation fails, please check whether you entered the data correctly. In 99,9% of all cases, typing or transcription errors are the reason for activation failing.

Entering the license code

If you have purchased a license extension or an update to a higher edition, click on “Input upgrade key” to enter the new activation data.

Note:

You must always enter the data for the full version first. You can then input the update or upgrade key after this (for instance, after reinstalling your operating system or moving to a new system).

go1984 User manual

Basic setup

6 Basic setup

In order to use go1984, one or more image sources are required. The following sources can be used:

· IP cameras

· Capture cards and TV cards

· Webcams (USB)

This section explains how to integrate cameras or other image sources into go1984. It also provides information on how to configure recording, on the integrated motion detection feature and on the notification options. We'll be working on the basis of a "typical" case, for which the pre-defined, automatic program settings are sufficient.

If you wish to make further changes or improvements to go1984, please refer to the section "Additional settings".

Basic setup

6.1 Adding a camera

6.1.1 IP camera

To add an IP camera, select the entry "IP cameras" in the go1984 explorer.

You now have two options for adding a new camera.

1. Camera picture

A list is displayed showing you pictures of all the available cameras, arranged in alphabetical order. You can use a filter to conveniently restrict the search for the model you want. You can use characters and numerics in any combination. For instance, the text “allnet” will list all the cameras that include this combination of letters in their name.

Similarly, a numeric combination such as “210” or an alphanumeric filter such as “210a” can be input as search terms.

If you select the "Ptz" checkbox you can limit your search to cameras with PTZ support.

You then double-click on the picture of the camera model you want to add.

2. Selection list

If you click on the “Add camera” button a list appears of the supported camera providers you can choose from.

go1984 User manual

Basic setup

You simply choose the model of camera you want from the list.

In both cases, the following dialog box appears.

Name

Give the camera a unique nickname which can be used for it in go1984.

Enter the camera’s IP address or host name here. If you have not yet assigned the camera an IP address, refer to the camera manufacturer’s documentation.

Port

If a camera port other than the default port “80” is being used, you can change this here.

Username

If authentication is required to access the camera, enter your username here.

Password

Enter your password here for the authentication process mentioned above. Refer to your camera manual for details of the default passwords.

Basic setup

You should set the following parameters in it:

Finally, click on “OK” to confirm your details.

The camera you've added will now appear in the branch "IP cameras" of the go1984 explorer. The basic setup of the camera has now been concluded. go1984 has automatically activated motion detection and recording for this image source. As standard, cameras only record when there is a detected motion. If

you want to record images permanently, simply deactivate the motion detection option by clicking on the “Motion detection” option box.

go1984 User manual

Basic setup

Note:

In the case of IP cameras that do not support simultaneous MJPEG and MPEG4 (dual streaming), or where only MPEG4 streaming is activated by default, MJPEG or Dual Streaming must be specifically selected in the camera settings (e.g. Allnet, Intellinet).

The section "Additional settings" provides information on how to edit further camera parameters such as resolution, frame refresh rates or panning.

Basic setup

6.1.2 PTZ camera

If the IP camera which has been added is a PTZ camera (PTZ = Pan/Tilt/Zoom), you can easily operate this via go1984.

Note:

If the camera’s live image appears but you cannot use the PTZ control, check the settings for "Host", "Port", "Username" and "Password" under “Video” à “PTZ settings” to see that they are correct.

There are different camera control options depending on the camera model:

1. Via the arrow keys

2. Via the slider

go1984 User manual

Basic setup

3. Via "click and drag"

Click on the button in the centre and hold the mouse button down. Now move the mouse crosshair within the PTZ field to move the camera to the position you want, which also allows you to use the pan and tilt functions comfortably:

Basic setup

4. Via "Ctrl" + mouse-click in the live image

If the live image is visible and the camera name highlighted, you can also control the camera using the Ctrl key and clicking inside the live image. In order to control the camera zoom, go across the image with the mouse and move the mouse scroll wheel. These functions are also supported in an image

center display.

5. Via "Area zoom"

If the camera being used supports an area a frame can be created in the image by holding the Ctrl key down, which is then highlighted. You need to select the camera name again to do this. This function is also supported in an image center display.

Preset-Positions

You can save up to 16 camera positions for each camera. To do this, simply click on the position you want.

Then enter a position description:

go1984 User manual

Basic setup

The new position is now displayed in color and can be accessed by clicking on it.

Basic setup

If you want the position to be displayed at certain times, you can link it via a right-click to a scheduler created beforehand. You can in fact link the position to any signal.

If you right-click on a saved position it can be deleted again:

Note:

Sometimes administrator rights are required to be able to save or delete positions for the camera.

go1984 User manual

Basic setup

6.1.3 Webcam (USB)

In order to be able to use your USB webcam in go1984, first install all the necessary drivers according to the camera manufacturer's instructions. Once the camera is available as a DirextX device in Windows, you can integrate it into go1984. For this, you first need to activate DirectX support. To do so, select the option as indicated in the diagram. At the next program launch, go1984 will search your computer for available DirectX devices and display them under "DirectX" in the go1984 explorer.

You now have the option of editing certain parameters such as the frame rate or the resolution.

Basic setup

6.1.4 Capture card

Capture cards are physically installed into the PC and convert analog image signals into digital signals. Start by installing the card in your computer and installing all required drivers as indicated by the card manufacturer's instructions. Most single channel capture cards based on the BT878 chip can be used. Usually, only the first channel of multichannel cards can be used in go1984. In addition, go1984 supports the following four channel cards:

· Spectra8 by ITuner

· Videum4400 by Winnov

After you've installed your capture card successfully, it will be available to you as a DirectX device. The next steps are the same as in the description for webcams (USB).

go1984 User manual

Basic setup

6.2 Recording

Recordings are automatically sorted by month to the respective camera in the go1984 explorer. If you wish to view the recordings, select the "Recordings" entry of the respective camera in the go1984 explorer. You'll be shown a list of all the months for which scenes are available.

Monthly overview

Selecting a month will take you to the monthly overview. Days are listed vertically, times of day horizontally. Each scene is represented as a little red mark in this overview. Moving the mouse pointer over the marks calls up a quick preview of the corresponding scene. You can open the selected scene for viewing by double-clicking on it.

Basic setup

Daily overview

If you wish to view the recordings for a specific day, select the day in the go1984 explorer as described below. You'll be provided with an overview over the scenes recorded on that day. Here, too, moving the mouse pointer over a scene will display a preview. Open the selected scene for viewing by doubleclicking on it.

In addition, you have the option of changing the playback speed of the preview mode and of defining the width of the preview scenes.

Loop mode:

the scene that is currently selected will be re-run at the end of the scene.

Endless mode:

all the scenes recorded on the camera are played back in sequence in chronological order.

Scene playback

You have two different modes available when you come to play back individual scenes.

go1984 User manual

Basic setup

6.2.1 Calculating memory requirements

One of the most frequently asked questions is: how much hard-drive space will the recordings use? There's no simple answer to the question because many factors play a role. These include:

· The number of cameras (AK)

· The number of frames per second (FPS)

· The image size (KB)

· The amount of compression

· Whether recording is permanent or motion-triggered

In order to get a rough idea of memory requirements in the case of permanent recording, use the following rule of thumb: You can usually assume the image size (KB) to be about 25-30 kilobytes.

AK * FPS * KB = kilobytes/second

This will give you the approximate number of kilobytes needed per second recorded. Multiplying by 3600 gives you an idea of the number of kilobytes needed per hour.

Please note that go1984 uses intelligent ring storage management to contribute significantly to efficient memory management. In many cases, it makes sense in any case to use motion-triggered recording, which reduces memory requirements substantially.

the used disk space exceeds this value:

in this case, you can allocate each camera a disk space quota. When this option is activated, the oldest scenes are automatically deleted when the quota is exceeded.

the scene is older than:

when this option is activated the scenes for each camera are automatically deleted when the scene is older than the duration specified in days.

disk space is less than:

the oldest scenes are automatically deleted when a quota for the remainder of the disk space is exceeded. This value applies across all the cameras which are recording on the same partition/hard drive and if changed, it is automatically set for all the cameras on this partition/hard drive.

go1984 User manual

Basic setup

6.2.2 Memory management

go1984 includes efficient ring storage. This enables you to optimize available hard-drive space allocation to the cameras, thereby ensuring that there is always enough memory space available for new recordings. go1984 is able to delete the oldest recordings automatically after the allotted memory has been used up. You can also select individual recording directories per camera.

The following criteria specifically apply for automatically deleting scenes. If more than one criterion is relevant, the first criterion to be met will apply in each case:

Basic setup

no motion was detected for this time interval:

if the time between two recordings triggered by motion detection is less than specified here, the scene already begun is continued. But if this time is exceeded a new scene is generated. The same applies if the recording is triggered by a signal other than internal motion detection (e.g. by a camera’s digital input signal or by an http event).

the size of the scene file is greater than:

a new scene is generated if the current scene exceeds the size specified here.

the duration of the scene is longer than:

if the scene duration specified here is exceeded a new scene is generated. If scenes are recorded by default only when there is a detected motion, the scene generated in this case will usually cover a longer period than specified under this point.

6.2.3 Scene generation

go1984 can aggregate recordings made during a certain interval to so-called scenes. This makes it much easier to find them later. The concept used is quite simple. Any scene that has already begun will be continued if less time than defined in the field "Time interval" has passed. If more time has passed, a new scene is generated. You can also define that a new scene should be generated as soon as the scene file becomes larger than the value entered into the field "File size" or if the current scene is longer than the value entered into the field "Duration".

The following criteria specifically apply for generating scenes. Once again, if more than one criterion is relevant, the first criterion to be met is decisive:

go1984 User manual

Basic setup

6.2.4 Pre-/Post alarm

Usually, motion-triggered recording begins the instant a motion has been detected. However, it is sometimes desirable to extend the recording by a few seconds before or after the event. To do so, simply enter the desired number of seconds into the appropriate fields and then activate the function using the corresponding button. go1984 uses your computer's random access memory (RAM) for this feature. In order to avoid too much memory being reserved, you have the option of restricting the size to a maximum value.

Basic setup

6.2.5 Access time period

Access to the recordings can be limited individually per user in the user management. Among other things, you can permit full access, no access, or access to a specified time period. This is where you can define the time periods valid for this camera.

Afterwards, simply select which time periods are available for the user in the user management.

go1984 User manual

Basic setup

6.2.6 Export

Recordings are saved in a proprietary format. However, the scenes recorded may be exported in AVI format or individual images in JPEG format.

When you are exporting to AVI format, you will be offered the codecs available on your system to choose from when it comes to video compression.

Basic setup

6.3 Motion detection

go1984 includes high-performance motion detection based on an optimized image difference process. When motion detection is triggered, the so-called "Motion" signal is activated for this camera. This signal can be used, for instance, to begin recording, to launch an FTP upload or to trigger an alarm.

The image is split for this purpose into 8x8 pixel segments which are each analyzed for motion. This means that with a resolution of 640x480 pixels, for instance, 4,800 segments must be analyzed for each individual image.

The threshold specifies what the minimum percentage of segments needs to be where motion is detected in relation to the whole image so that a motion is indicated. For instance, in the case of a VGA resolution of 640x480 pixels with a threshold of 1.5%, the figure will be 72 segments.

You should reduce the threshold if you want the motion detection facility to be more sensitive.

Motion areas are highlighted in the live image with red squares. As soon as the actual value exceeds the specified threshold, the motion signal is triggered. The specified threshold (yellow) and current actual value (green or red) are graphically represented by two colored bars in the program to make adjustments easier for you. The actual value bar changes from green to red if a motion has been detected. The circle in the “Motion” field also turns red.

You'll be shown the live image from the camera, with motion areas being marked by red rectangles. As soon as the actual value surpasses the specified limit value, the motion signal is triggered. The specified limit value (yellow) and the current actual value (green or red) are graphically represented by two colored bars in the program in order to make adjustment easier for you. The actual value bar changes from green to red if a motion has been detected. The circle in the "Motion" field also lights up in red.

Pen for freehand drawing of masks

Rectangle tool for drawing masks

Eraser for deleting masks

Show or hide camera image

Line width 1

Line width 2

Line width 3

Line width 4

Invert mask

Load mask

Save mask

Delete mask

It often makes sense to exclude certain areas of the camera image from motion detection. In order to do so, you can draw any kind of mask over the image. Various tools are available for doing so. The

mask is displayed on the screen transparently for control purposes. Grayed out areas will be excluded from now on.

go1984 User manual

Basic setup

Tools for drawing masks:

Basic setup

For normal purposes, motion detection settings do not need to be adjusted more than described above. If the default values don't work perfectly for your needs, you'll find additional setup options on the "Properties" tab.

The analyzed segments are sorted in ascending order in the bar chart according to detected motion intensity. The maximum motion share indicates which percentage is relevant to the analysis. The segments before this are excluded.

go1984 User manual

Basic setup

If the motion intensity of individual segments (red bar) now exceeds the green line in the relevant area (yellow), the detected motion is highlighted in the relevant segment (red rectangle in the live image).

The green line originates from the factors “Noise suppression” and "Max. motion share”.

The reduction in noise suppression along with the increase in the max. motion share therefore result in a higher level of sensitivity in terms of motion detection.

You will also find the following set-up options:

Analyze only every xth frame

motion detection is highly processor-intensive due to the image

decompression required.

Delayed detection

delay in seconds until the motion signal is triggered. This may, for instance, be a sensible option for an e-mail alert in order to send a relevant image.

Idle signal after

duration in seconds until the idle signal is triggered. For further information, refer to the “Event management” section.

Motion value is greater than

This control enables you to avoid motion detection being triggered by rapid, extreme lighting changes such as the interior lighting being switched on or auto-iris adjustment by cameras etc.

Brightness is less than

Some cameras tend to produce noisy pictures under bad lighting conditions, which can lead to motion detection being triggered. This control enables you to turn off motion detection for images generated at less than the specified basic brightness.

Threshold: Automatic

go1984 always tries to provide the best settings for the segment threshold independently.

Threshold: Manual

analysis of each individual segment without the above-mentioned extended, adaptively operating settings being taken into consideration for the segment threshold. This option is recommended only in exceptional cases.

Basic setup

go1984 User manual

Basic setup

6.4 Http event

Many of the current network cameras or even external network-enabled motion detectors nowadays offer integrated motion detection and the facility to notify third-party systems of any movement detected via an http message. In the Enterprise edition of go1984 the motion detection facility of these devices can be used via the http event. This may be a particularly sensible solution on performance grounds where there are a large number of cameras.

You will find this function under the IO-Manager. You can add a new event by clicking on the relevant button.

Enter the name you want to give the event.

Basic setup

The new signal is now available and can be activated or deactivated via the shown URLs.

The other settings are now applied directly via the web interface of the camera or motion detector. Take as an example the settings for an axis camera shown below.

First of all, the go1984 server is created as an “event server”.

You can check the connection directly using the “Test” button.

Events can now be defined accordingly at the start and end of the movement:

go1984 User manual

Basic setup

Enter the “On-URL” parameter under “User-defined parameters” for the event at the start of the motion:

name=my_event&active=1

Then add a “MotionEnd” event which will be triggered at the end of the motion. Enter the following parameters for this event: name=my_event&active=0

Then you must link the recording in go1984, which is linked by default to go1984 motion detection, to the http event.

go1984 User manual

Basic setup

If you are not going to continue using the go1984 motion detection function any more or as an alarm

function, for instance, you can now deactivate it.

Basic setup

Note:

Sometimes you need to still change the values for the pre- and post-alarm so that the recorded scenes cover the overall period you want.

go1984 User manual

Basic setup

6.5 Notification

go1984 can use various channels to notify you in case of an alarm. They are:

· Playing an audio file via a sound card

· Sending an e-mail with or without an image attached

· Uploading one or several images via FTP

· Sending an image to the go1984 client via UDP Broadcast

· Launching an external program

· Calling a telephone number and playing an audio file (ISDN card required)

Note:

All notification types need to be activated first. Clicking on the options field of the respective option switches on the corresponding function.

If the desired option is grayed out, there are some settings that must be provided beforehand because the option makes no sense without them. For instance, the option "Telephone call" makes no sense if a telephone number has not been provided.

Basic setup

6.5.1 Sound

go1984 can play a freely selectable audio file in .wav format via your sound card in case of a notification. Simply choose the corresponding file using the dialog.

To prevent too many notifications from being sent, you can set a rest period. This means that only when at least the specified time has elapsed since the last playback can the sound file be played again.

Please also refer to the general notes on activating notification functions in the section on notifications.

go1984 User manual

Basic setup

6.5.2 E-mail

In order to enable e-mail sending from go1984, a so-called SMTP server (see reference) first needs to be specified. If this has already been done, you can continue here directly.

Select the entry "Notification" in the go1984 explorer. You can now enter one or several recipients (separated by semicolons) into the field E-mail address. Adjust the subject line if you wish. The variable "%cameraname%" is automatically replaced by the name of the camera triggering the alarm when an e-mail is sent.

Once again you have the option to set a rest period which must elapse between sending two e-mails, by clicking on the clock icon. Simply click on the clock icon and then set the rest period you want.

Please also refer to the general notes on activating notification functions in the section on notifications.

Note:

The Action button is linked by default to the go1984 motion detection function. If you want to send a meaningful image as an attachment when a movement is detected, you must sometimes increase the “Delayed detection” value under “Motion detection” à “Settings”.

The delayed detection will obviously have an impact on recordings too. But you can balance out this delay simply by increasing the pre-alarm value accordingly.

Basic setup

FTP server

Domain name or IP of your FTP server, e.g. ftp.online.com

Port

FTP port, almost always "21"

FTP user ID

Username for logging on to the FTP server

FTP password

Password for logging on to the FTP server

FTP directory

FTP server subdirectory where you want the images to be saved

Passive mode

If your FTP server cannot be run in the active mode, select this option

Keep connection

After uploading an image, the connection to the FTP server is kept open. If you prefer the connection to be shut, deactivate this option.

Simple filename

The file name is the name you enter into the field

Datetime filename

The file name includes the time of day. The constant part of the file name has to be enclosed in quotation marks. Formatting is carried out according to the following key: yyyy Year mm Month dd Day hh Hour nn Minute ss Second zzz Millisecond

Rotating number filename

Enter the beginning of the file name into the field. A number is automatically added onto the end of the name; it is increased by one after each successful upload. After the counter reaches the defined value, it is reset to 1. Older images are then overwritten.

Upload as "*.tmp" and rename if finished

If you have problems uploading the files to your ftp server, you can have the images uploaded with the extension ".tmp" at first. After the upload has been successfully completed, the files are renamed to the "real" file name.

6.5.3 FTP

If you wish the images from a camera to be sent to an FTP server in addition to being stored locally, complete the following dialog.

First, enter the login data for your FTP server:

You can also choose to resize images before saving them on the FTP server. Activate this option and define the new size of the image using the corresponding fields.

Finally, you can define under which names to save the file(s) on the FTP server:

go1984 User manual

Basic setup

The Action button is linked by default to the "NewImage" signal (see also “Event management” section). This means that the FTP upload is activated every time a new camera image is generated. In this case too you have the option to set a rest period by clicking on the clock icon. This means that only when the period specified between two transmissions to your FTP server has elapsed can a new upload operation be launched. This then allows you to have the FTP upload operation simply carried out at a set interval.

Please also refer to the general notes on activating notification functions in the section on notifications.

Basic setup

6.5.4 LAN-Broadcast

In the event of an alarm, go1984 can notify any users on the LAN via UDP Broadcast. If the go1984 client has been installed and is active, users will be notified about the movement detected on a camera via popup and/or an acoustic signal.

Note:

The go1984 client should not be confused with the go1984 desktop client. Unlike the latter, it is not suitable for permanent live monitoring via one or more cameras or for recording images from them.

You can install the go1984 client on another computer by running the go1984 setup and only ticking the "go1984 Client" option box.

The broadcast client can then be launched via the Windows Start menu.

Now activate LAN Broadcast for the cameras you want.

go1984 User manual

Basic setup

You also again have the option here to set a rest period by clicking on the clock icon. This means that only when at least the specified period between two broadcasts has elapsed can a new notification be sent.

Please also refer to the general notes on activating notification functions in the section on notifications.

If a motion is detected you will be informed via popup from now on. The last images transmitted can be replayed by clicking on the “Play” button.

You can also apply other settings on the broadcast client.

Popup on new image

go1984 client appears in front when any motion is detected

Startup minimized

go1984 client is minimized on start-up

Play sound on new image

Choose whether and with which sound file you would like to be notified if a motion is detected

Notify again after

Minimum period which must elapse before the next time you are notified

Number of buffered snapshots

Number of buffered images (max. "100")

Select Skin

Choose one of the available skins

Basic setup

Show StatusBar

this displays/hides the status bar with additional information such as resolution, notification time, image size in the bottom section of the go1984 client window

Show Toolbar

this displays/hides the go1984 client toolbar

Stretch

this expands the image in the visible area (stretches)

Setup ...

this opens the dialog box for advanced settings

Show

this brings the go1984 client to the front again

Hide

this minimizes the go1984 client

Exit

this exits the go1984 client

Most Windows programs are shut down completely when you close the program window. The go1984 Client is only hidden and continues to run in the background.

While the program is running, the go1984 Client symbol is displayed in the task bar near the time. You can use it to shut the program down completely or to bring it back to the foreground. Clicking on the icon with the right mouse key will open the corresponding menu.

go1984 User manual

Note:

Basic setup

The following functions are also available.

Basic setup

6.5.5 External program

go1984 offers you the option of launching an external program in case of a notification. In this case, the image that triggered the notification can first be saved on the hard-drive. In this way, special tasks can be carried out for which go1984 itself is not suitable.

To set up the feature, select the program you want to launch and the launch type. You can choose to have the image that triggered the notification saved on the hard-drive first, and can freely define the drive and the directory for this purpose.

Here, too, you have the option of defining a rest time by clicking on the clock symbol. A program is only launched if the defined time has elapsed between two program launches.

Please also refer to the general notes on activating notification functions in the section on notifications.

go1984 User manual

Basic setup

6.5.6 ISDN

In case of an alarm, go1984 can make a telephone call using an existing ISDN card. Once the connection is set up, the program plays a freely definable audio file to the person being called. Please enter the telephone numbers using only numeric digits. Other signs or spaces can disrupt the function.

You can record your own audio files using the Windows "Audiorecorder". Please make sure you've set the right format:

· PCM 8,000kHz; 16 Bit; Mono

In order to avoid being notified too often by calls, you can define a rest time that has to elapse between calls. To do so, click on the clock icon and set the desired rest time on it.

Please also refer to the general notes on activating notification functions in the section on notifications.

Basic setup

6.6 Scheduler

go1984 provides the option of executing certain functions such as recording or notifying only at certain times. You can define as many schedulers as you like, which can then be linked to the corresponding functions. In order to create a new scheduler, select the option "Scheduler" in the go1984 explorer.

You can give each scheduler a unique name.

Afterwards, define the active and inactive times for each day. Simply select the desired times using the mouse (keep left mouse button pressed). The active part will be shaded in green. You can copy any day's settings to a different day using drag & drop. Simply use the mouse to drag the name of the day (Monday, Tuesday, etc.) to a different day. Furthermore, you have the possibility of saving the completed scheduler to a file or loading it. This is a useful feature when setting up several similar schedulers.

go1984 User manual

Basic setup

You can also use the scheduler to turn various camera functions on or off automatically. The mouse pointer changes to the following symbol when held over linkable functions: . Clicking with the right

mouse button opens the menu for creating and editing links. Use the "Event à Scheduler à ..." entry to select one of the existing schedulers, which will then turn the selected function on or off.

Basic setup

Note:

If certain functions need to be active at exactly opposite times (in this case, for instance, opening hours), you do not necessarily need to create an extra scheduler. If you right-click again on a scheduler link you can reverse the scheduler.

Under the “Holiday planner” tab you have the option to define days that should be processed separately. These definitions have a higher priority than specified week schedulers. In many countries public holidays are already pre-determined and can be changed or removed as required. You can also add via the calendar additional days for the current year or for each year.

Make sure that the holiday planner is not activated by default, as specified holidays will continue to be ignored. You activate this function by selecting the “Active” checkbox.

go1984 User manual

Basic setup

User management

Username

: Administrator

Password

: [blank]

7 User management

User management allows you to allocate individual authorizations for access to the program interface, the web interface, recordings, and PTZ camera control. Directly after installation, user management is not activated, i.e. all functions are accessible without entering a username or password. Activate user management by clicking on the corresponding option field.

After activating the user management, access is only allowed after entering a valid username. go1984 creates a predefined, non-deletable Administrator account which always owns all access rights. This account can be used without a password at first. However, you should define a password as soon as possible by editing the Administrator account.

Cameras

Access to live feed, PTZ control, recording period

General

Deletion of scenes

Treeview

Access to IO functions, webserver settings, camera settings

Web

Access to the different browser views

The "User" column displays all existing users. Use the three buttons to create, edit or delete users. Please note that a newly created user has no rights by default. In order to edit a user's right, first select the user. Afterwards, use the "Access rights" column to allow or deny the desired options. You can also change several users' rights in a single step. To do so, first select the first user, then press the CTRLkey on your keyboard and hold it while selecting one or several users from the list.

Access rights are subdivided into the following areas:

go1984 User manual

User management

Don't forget to save the edited settings using the "Save" button.

Note:

If new cameras are integrated after a user is created, the right to access the cameras must be granted explicitly to the user that has been previously created.

Webserver

8 Webserver

go1984 provides an integrated webserver that is accessible from local networks and the Internet using TCP/IP. The server makes it possible to access the live feed and recordings using the Internet Explorer. Controlling PTZ cameras is also possible. What's makes the feature special are the HTML templates, which permit a completely customizable design of appearances and functions. Use the examples provided to adapt them to your own needs. You'll find the templates in the following directory:

<InstallDir>\Web

where <InstallDir> is the directory where go1984 was installed.

go1984 User manual

Webserver

8.1 Configuration

go1984 is delivered with predefined webs that can be called up using an Internet browser. Every web is saved in its own subdirectory. The root web directory can be specified. In addition, the available bandwidth can be limited. go1984 analyzes your computer's network configuration and displays all IP addresses to which the webserver responds. It is also possible to make the computer accessible via the Internet using a dynamic domain name.

Webserver

The web interface addresses the available cameras using a so-called index. This is a consecutive series of numbers which you can use to define in which order the cameras are displayed on the web interface.

You can also view information regarding the currently active and inactive connections to the webserver. For instance, the display indicates the session ID, the starting time, the time to automatic disconnection in case of inactivity, the username and so on.

by the IP address or domain name of the computer running go1984

port

by the port defined in the webserver configuration (default is 80)

by the IP address or domain name of the computer running go1984

port

by the port defined in the webserver configuration (default is 80)

web

by the directory name of the web. The following webs are predefined as examples:

· java

· tree

· activex

· javascript

· pda

· iPhone

go1984 User manual

Webserver

8.2 Interface

Call up the web interface in your browser by using the following URL:

http://ip:port

Replace the variables as follows:

You will then end up at the web server homepage where you can choose the web and transmission quality that you want ("high" or "low"). You will also find the option to install the go1984 desktop client:

You can also access the web you want directly:

http://ip:port/web

Replace the variables as follows:

In the tree web you can also specify the camera or view you want directly:

...?view=x" (1=2x2, 2=3x3 etc.) or ...?camera=cameraname

The complete URL could look something like this:

The web interface shown in the diagram will then be displayed in your browser.

Webserver

If you've activated the user management, you'll first be shown a login request requiring you to enter a valid username and password.

go1984 User manual

Webserver

Note:

In order for all example webs to run correctly, you may have to modify your browser's security settings. If you have no Java Virtual Machine installed, you can download it free of charge at the following URL:

http://www.java.com

If you wish to use ActiveX-based webs, allow the following security settings:

· Run ActiveX elements which are safe for scripting

· Run ActiveX PlugIns and controls

· Download unsigned ActiveX controls

· Active scripting

If you wish to use Java-based webs, allow the following security settings:

· Scripting of Java Applets

· Active scripting

Webserver

by the IP address or domain name of the computer running go1984

port

by the port defined in the webserver configuration (default is 80)

8.3 iPhone Client

The go1984 web server provides a special interface for the iPhone. This offers you the chance to access the go1984 server via the go1984 iPhone client. You can also establish a connection to the go1984 server both via a WLAN and via GPRS/Edge. This provides you with access to live images from all the cameras on the go1984 web server which you have the relevant access rights for.

Call up the web interface in your browser by using the following URL:

http://ip:port

Replace the variables as follows:

To change camera, select one from the camera list.

Each camera gives you access to the entire recordings archive. You can use this simply to browse through the scenes available for a particular day or select another day. To help you find the relevant scene quickly, a preview is displayed for each recording. When you select the scene you want it starts playing.

go1984 User manual

Webserver

If it is a PTZ camera you can insert transparent buttons next to the relevant camera so that you can pan, tilt and zoom the camera via the touch-sensitive display.

Webserver

8.4 J2ME Client

You can also use a cellular phone with Java capability supporting the MIDP2.0 standard to access go1984. More specifically, you can

· view motion-controlled live images

· switch between the different cameras

· control PTZ cameras

Your cellphone has to be configured in such a way that the computer on which go1984 is running is accessible via the Internet. To this end, you can connect using the CSD, GPRS or UMTS standards. If your cellphone is not pre-configured for Internet access, please refer to your cellphone's instruction booklet for the correct settings or contact your network provider. In addition, the go1984 computer has to be accessible via the Internet using a static Internet IP address or a dynamic domain name.

Install the go1984 applet according to your cellphone's instruction booklet. You'll find the required JAD/ JAR files in the following directory:

<InstallDir>\web\wap\ota\

<InstallDir> is the directory where go1984 was installed. You can launch the applet directly after installing it. First open the settings dialog.

Host

IP address or dynamic hostname of your go1984 computer

Username

Username as defined in the user management

Password

Password as defined in the user management

Bandwidth

Maximum bandwidth in bytes/second

Startup camera

[Optional] Name of the camera that is automatically displayed after the connection has been set up

The following fields need to be completed:

go1984 User manual

Webserver

2Up8

Down

Left6Right

Zoom out

Zoom in

Preset mode on/off. When you press this key, the letter "P" is displayed at the bottom right of the screen. You can now control predefined/preset positions of the PTZ camera using the numbers keys 1…9. Press the * key again to resume manual control.

After you've completed all fields and confirmed them, you can build up a connection to the go1984 server by pressing "Connect". The image from the camera is displayed. The connection to the server is maintained. In order to minimize costs, a new image is only sent to the cellphone if a motion has been detected. Press the "More" key to display a list of the available cameras to which you can also switch. If the selected camera is a PTZ camera, you can control it using the numbers keys:

go1984 User manual

Webserver

8.5 DynDNS

In order to make go1984 accessible via the Internet, you need to have either a static Internet IP address or a dynamic domain name. The latter can be set up free of charge using the DynDns.org service. Use the following link to set up an account:

https://www.dyndns.org/account/create.html

Complete the selected fields to create an account. After submitting the form, you'll receive a confirmation at the e-mail address you provided. Click on the link in the e-mail to confirm your account.

Now you can log onto the service using your username and password in order to set up a domain name.

Click on the "Services" link, then on "Dynamic DNS" and finally on "Get Started".

Webserver

All you need to do is complete the Hostname field. Choose a hostname that is easy to remember and distinctive. If you like, you can select a different extension for your domain name using the drop-down menu indicated. Ignore all the other fields and simply click on the [Add Host] button. If the hostname you've chosen is no longer available, choose a different one.

go1984 can now automatically update the domain name. Initiate the process by providing the domain name you've chosen, your username and password, and by selecting the option "Automatically update DynDNS Domain". Now you'll be able to access your computer from the Internet using the dynamic domain name.

go1984 User manual

Webserver

8.6 Clustermode

In the Enterprise edition of go1984 any cameras that have been integrated on a remote computer into another go1984 Standard, Pro or Enterprise version can be added as “cluster cameras”.

This offers benefits in terms of:

· Network load: images can only be transmitted when a motion is detected; the camera on the cluster

client is almost in standby mode

· Performance: it may also be sensible to set up a cluster system for load distribution. The cluster

server or servers will then take over motion detection while the cameras on a central cluster client are brought together.

A new cluster camera is created on the cluster client in the same way as adding an IP camera. This means that you select the “IP cameras” option in go1984 Explorer. Then choose the camera "go1984 Camera" from the selection list.

Now specify the IP address or host name under which the go1984 cluster server can be accessed.

The next step is for you to give the camera a unique nickname which can be used for it in go1984.

If the user manager is active on the cluster server you must enter a valid username/password combination for authentication.

You must then enter the name of the cluster server camera in the “Camera” field which you intend to access. You can also determine via the “Motion” parameter whether images should be transmitted permanently (Motion = "0") or only when motion is detected (Motion = "1"). If you intend to transmit the image in a different resolution or compression level to that of the original image due to a small amount of bandwidth being available, you can set this via the parameters "Width" and "Height" or "CompressionLevel". A compression level of "100" corresponds to the image’s original quality.

go1984 User manual

Webserver

You can see in the screen below that no images are transmitted as long as there is no kind of movement ("0 fps"). The cluster camera is therefore almost in standby mode. The motion detection function can now be deactivated. Then every relevant image transmitted is recorded.

Note:

A web server session is initiated on the cluster client for every active cluster camera. If the cluster server being used is a Pro edition one, a maximum of two cameras can be operated in this way. With a Standard edition server a maximum of one camera can be operated like this (see “Editions” à "Webserver sessions").

go1984 User manual

Image Center

9 Image Center

The Image Center is a flexible tool for viewing one or several cameras on a screen. The camera arrangement is controlled using so-called views. go1984 provides numerous templates suitable for different resolutions.

First, define a view by selecting the appropriate one from the list of available templates. Double-clicking on it creates a new view that you need to provide with a unique name.

Image Center

You'll now be shown the newly created view in the go1984 explorer, in which one or several placeholders are defined which will be replaced by the camera images later on. To link a placeholder to a camera, click on it using the right mouse button. This calls up a menu with a list of all available cameras. Select a camera from the list. You also have the option of placing a graphic behind the entire view.

You can define as many views as you like, which can then be displayed simultaneously on various monitors or sequentially on a single monitor. Next, select the "Screens" entry from the go1984 explorer in order to generate such a representation. First, click on the "Create a new screen" button. A "Screen" can contain one or more views. Use the button to select and add the desired views to the list of "Views for this screen". If you've added several views, go1984 can automatically switch between them at certain intervals.

go1984 User manual

Image Center

You can modify additional settings such as "Position", "Keyboard shortcuts" or "Properties" using the corresponding entries.

Clicking on the "Show" button displays the preset "Screen".

Image Center

[Size]

size of the whole view

[No.]

numbering of the objects contained: these may be specifically

- "PaintBox" a placeholder for the camera image

- "PTZ" a placeholder for the PTZ field for a controllable camera

Defining customized views

If the views supplied don’t match up with your expectations, you can add more templates in a simple manner.

You will find the definitions for the views (*.ini) under the go1984 installation folder in the “Template” directory. You can edit these using a simple text editor or you can add more vi

The definitions describe the following in detail:

Note:

The new template will only be available after you have restarted go1984.

go1984 User manual

Additional settings

10 Additional settings

10.1 Camera

In order to modify other camera settings, please select the camera in the go1984 explorer. You now have the option of influencing image processing.

Note regarding IP cameras:

The button carries out a special function. While it is activated, the original *.jpg image from the IP cameras is used in go1984; modifications such as rotating, mirroring or adding text are not possible. In this way, go1984 can run at its optimum performance level. Wherever possible, try to apply camera settings in the camera itself which make further modifications by go1984 unnecessary. If your

camera is not able to do this, deactivate the button and apply the settings in go1984.

Additional settings

Fit image to visible area (expand)

Maintain image proportions

Use original image from camera (for best performance)

Flip image horizontally

Flip image vertically

Rotate image by 90°

Rotate image by 180°

Rotate image by 270°

If you want the image to be captioned, use the [Caption] tab. This function is also only available when the button is not activated.

You set the image record pause using the following sliders. The default setting is 200 ms, i.e. 5 images per second (fps). In order to avoid increasing the network load and memory requirements unnecessarily, you should in this case set the actual value required rather than the highest possible value. In most cases, using higher image refresh rates hardly results in scenes with greater information content.

As with many other sliders, you also have the option here to specify for your own convenience the value you want in an additional window which opens when you double-click on [Pause between two frames].

go1984 User manual

Additional settings

Some additional information about the camera is displayed at the bottom of the screen.

Additional settings

10.2 Startup settings

You can choose to launch go1984 minimized. In this case, the application will not be visible at first. Only the little go1984 program icon will appear next to the system clock. Double-clicking on the icon will open the application interface. As a further option, you can set go1984 to be launched automatically when Windows is started. If you are operating go1984 in service mode (see "Installation" section), deactivate this option as the go1984 service is then automatically started. If you don't like the selected standard skin, you can choose a different one.

go1984 User manual

Additional settings

10.3 HTTP Proxy

If a proxy server is required for the HTTP protocol in your network, define the necessary settings here. Ask your network administrator for the correct settings.

Additional settings

10.4 SMTP server configuration

In order to enable e-mail sending from go1984, a so-called SMTP server first needs to be entered; this only has to be done once. Outgoing e-mails are sent to this server and ultimately to the recipient. Your provider can supply you with the settings required to configure the SMTP server. Alternatively, you can obtain the information from your e-mail program (Outlook, Outlook Express etc.). A list of the most common servers is supplied in the appendix.

In most cases, it is sufficient to complete the fields shown in the diagram. If go1984 is still not able to send e-mails, check the settings or test using the "POP3-before-SMTP" authentication method. To do so, please complete the "POP3 access data" block.

go1984 User manual

Additional settings

10.5 Translation

It is possible to integrate new languages for the interface. The following table shows the available languages.

If you wish to create a new language option, right-click on a free column in the table. Select an existing language as a template. A dialog box appears requesting you to enter a name for the new language (e. g. Spanish). Use the existing languages to translate terms line by line into the new language. After completing the translation, the newly created language option is immediately available.

go1984 User manual

Event management

11 Event management

go1984 includes a highly flexible event management option, which permits go1984 to be individually configured. Various input and output signals are available. These signals can be supplied to go1984 by cameras, schedulers or plug-ins.

Every input signal can be linked to one or more actions. The most important signals are automatically linked to standard actions after go1984 is installed. For instance, motion detection is linked to recording and notifications of the respective camera. However, you have the choice of changing these links.

The following output signals (Actions) are available (depending on camera type):

Output1, Output2, ...

This output signal can be used to switch a camera's digital output (if available) on or off. It can be used for applications such as controlling a door-opener, for instance.

Note:

An IP camera’s digital inputs or outputs are not supplied as standard. They must be explicitly activated when required, in other words, set from "0" to "1".

The following input signals (Events) are available:

Signal

is activated when...

Active

the camera is active, which means that the option box next to the “Video” option is ticked.

Darkness

the brightness of the camera image is very low (see Motion detection à Settings à "Brightness is less than").

Error

the camera reports an error or is not available.

Idle

no further motion has been detected for the value “Motion detection” à “Settings” à “Delayed detection".

Input1, Input2, ...

the camera's digital input is being closed.

Motiondetector

a movement is detected.

MotionOverload

the motion level is very high (see Motion detection à Settings à "Motion value is greater than").

NewImage

a new image is transmitted from the camera.

PreRecording

pre-recording is active.

Recording

images are being recorded at that moment.

SceneActive

a new scene is recorded and the interval specified without movement which must elapse before the next scene is generated (see “Scene

generation” à "No motion was detected for this time interval") has not yet

expired.

Scheduler

the scheduler is in the green range.

Http event

the http event is currently active.

Event management

Signal on

Signal off

Signal is deactivated and therefore not available (default setting for camera inputs and camera

outputs)

The different input signals are grouped in the program's IO Manager. LEDs are depicted to the left of the signals. The LEDs may indicate the following status:

You can view the different signals from the cameras in the IO Manager under the "Event" entry. It also shows you which signal has been linked to which action.

go1984 User manual

Event management

You can create links anywhere the mouse pointer changes to the following symbol: Clicking on the icon with the right mouse key will open the links menu. The following example illustrates the process.

Example:

An IP camera's digital input has been linked to a doorbell. Whenever a visitor rings the bell, the camera is supposed to start recording. To set up this event, first choose a camera in the go1984 explorer and then select the "Record" option.

The various settings available for go1984's recording function are shown. The Action button is near the bottom. The button is linked to go1984's internal motion detecting after installation. You can now change this link, mapping it to the camera's digital input. Click on the button with the right mouse key to open the menu. Afterwards, select "Input1" as an input signal, as shown in the diagram. After you've defined this setting, the camera will start recording as soon as the contact at the camera's digital input is closed.

Note:

Please note that a single input signal can also be linked to several different actions.

In the example above, for instance, you could have the same signal trigger e-mail notification in addition to recording. Furthermore, a camera's signals are also available for all other cameras. In the example, the input signal from a single camera could be used to control the recording function of all cameras.

1und1

POP3-Server: pop.1und1.com SMTP-Server: smtp.1und1.com Pop-Kontoname: ptXXXXXX-XXX (Mailbox-Name)

ARCOR

POP3-Server: pop3.arcor.de SMTP-Server: postman.arcor.de (mail.arcor.de) Pop-Kontoname: Benutzername

E-PLUS

POP3-Server: mail.imail.de SMTP-Server: mail.imail.de Pop-Kontoname: Benutzername

FREENET

POP3-Server: pop3.freenet.de SMTP-Server: mx.freenet.de Pop-Kontoname: benutzername@freenet.de

GMX

POP3-Server: pop.gmx.net SMTP-Server: mail.gmx.net Pop-Kontoname: Kunden-Nummer oder E-Mail

LYCOS

POP3-Server: pop.lycos.de SMTP-Server: smtp.lycos.de Pop-Kontoname: Benutzername@lycos.de

o2 Online

POP3-Server: pop.o2online.de SMTP-Server: mail.o2online.de Pop-Kontoname: IhreRufnummer@o2online.de

RTL World

POP3-Server: pop3.rtlworld.de SMTP-Server: smtp.rtlworld.de Pop-Kontoname: Benutzername

Schlund +Partner

POP3-Server: pop.kundenserver.de SMTP-Server: auth.smtp.kundenserver.de Pop-Kontoname: m1234567-1 (Mailbox-Name)

STRATO

POP3-Server: post.strato.de SMTP-Server: post.strato.de Pop-Kontoname: name%eigenedomain.de

T-ONLINE

POP3-Server: pop.t-online.de SMTP-Server: mailto.t-online.de Pop-Name: Anschlusskennung|T-Online-Nr.|0001@t-online.de

T-ONLINE SMTP

POP3-Server: pop.t-online.de SMTP-Server: smtprelay.t-online.de Pop-Name: Anschlusskennung|T-Online-Nr.|0001@t-online.de

TISCALI

POP3-Server: pop.tiscali.de SMTP-Server: smtp.tiscali.de Pop-Kontoname: Benutzername ohne '@tiscali.de'

VODAFONE

POP3-Server: pop.email.vodafone.de SMTP-Server: smtp.email.vodafone.de Pop-Kontoname: Tel-Nummer o. Alias|@vodafon.de

WEB.de

POP3-Server: pop3.web.de SMTP-Server: smtp.web.de Pop-Kontoname: Benutzername

YAHOO

POP3-Server: pop.mail.yahoo.de SMTP-Server: smtp.mail.yahoo.de Pop-Kontoname: E-Mail-Adresse ohne '@yahoo.de'

go1984 User manual

12 Appendix

12.1 POP3/SMTP-Server

A list of the most common POP3/SMTP servers:

Appendix

Masthead

logiware gmbh

Alfred-Mozer-Str. 42

D-48527 Nordhorn

Germany

Telephone (+49)(0)5921 7139925

Telefax (+49)(0)5921 7139929

Internet : http://www.go1984.de

E-mail sales : sales@logiware.de

E-mail support : support@logiware.de

13 Masthead

All company and/or product names are trademarks and/or registered trademarks or brands of the respective manufacturers. We reserve the right to make technical changes and assume no responsibility for errors or omissions.

Logiware go1984 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Introduction

Editions

Installation

Launching the program

Entering the license code

Basic setup

6.1 Adding a camera

6.1.1 IP camera

6.1.2 PTZ camera

6.1.3 Webcam (USB)

6.1.4 Capture card

6.2 Recording

6.2.1 Calculating memory requirements

6.2.2 Memory management

6.2.3 Scene generation

6.2.4 Pre-/Post alarm

6.2.5 Access time period

6.2.6 Export

6.3 Motion detection

6.4 Http event

6.5 Notification

6.5.1 Sound

6.5.2 E-mail

6.5.4 LAN-Broadcast

6.5.5 External program

6.5.6 ISDN

6.6 Scheduler

User management

Webserver

8.1 Configuration

8.2 Interface

8.3 iPhone Client

8.4 J2ME Client

8.5 DynDNS

8.6 Clustermode

Image Center

Additional settings

10.1 Camera

10.2 Startup settings

10.3 HTTP Proxy

10.4 SMTP server configuration

10.5 Translation

Event management

12.1 POP3/SMTP-Server

Appendix

Masthead