Revision
1.0
. 2013
Logitek
Looggiitteekk
L
Elleeccttrroonniicc SSyyssttee
E
Mosaic Reference Manual
mss
m
Dec
Logitek Electronic Systems, Inc.
5622 Edgemoor Drive
Houston, Texas 77081
USA
Tel 877-231-5870
+1-713-664-4470 (outside U.S. and Canada)
Fax +1-713-664-4479
Email support@logitekaudio.com
Web www.logitekaudio.com
Contents © 2013 Logitek Electronic Systems, Inc.
Notice
Every effort has been made to supply complete and accurate information. However, Logitek Electronic Systems, Inc. assumes no
responsibility for its use, nor any infringement of patents or other rights of third parties, which would result.
Worldwide rights reserved. Except for your own personal use, no part of this publication may be stored in a retrieval system,
transmitted or reproduced in any way, including but not limited to photocopy, photograph, magnetic or other record, without the
prior agreement and written permission of Logitek Electronic Systems, Inc.
Logitek, JetStream, and Mosaic are trademarks of Logitek Electronic Systems, Inc.
All other trademarks acknowledged.
All specifications are subject to change without notice.
Document Revisions
Date Revision Author Notes
November, 2013 0.5 John Davis Preliminary release of Mosaic manual
December, 2013 1.0 John Davis First release
Logitek Mosaic Reference Manual
Page 4
Contents
Document Revisions................................................................................................................................ 3
Contents 4
1 Introduction ........................................................................................................................................ 7
About this Manual .......................................................................................................................... 7
Intended Audience ........................................................................................................................ 7
Manual Conventions ...................................................................................................................... 7
About the Mosaic ........................................................................................................................... 8
System Requirements..................................................................................................................... 9
System Architecture ....................................................................................................................... 9
Compatibility Matrix .................................................................................................................... 10
2 Unpacking ......................................................................................................................................... 11
Parts List ........................................................................................................................................ 11
Unpacking..................................................................................................................................... 11
Contacting Logitek ....................................................................................................................... 11
3 Physical Installation ........................................................................................................................ 12
Power Supply Unit ....................................................................................................................... 12
Mosaic Frames.............................................................................................................................. 12
M2-F10 10 Slot Frame................................................................................................................. 12
M2-F12 12 Slot Frame................................................................................................................. 13
M2-F18 18 Slot Frame................................................................................................................. 13
M2-F22 22 Slot Frame................................................................................................................. 13
M2-F30 30 Slot Frame................................................................................................................. 13
Meter Bridge (CL-Meter).............................................................................................................. 13
Mounting ...................................................................................................................................... 13
Connections.................................................................................................................................. 15
PSU................................................................................................................................................ 16
GPIs ............................................................................................................................................... 17
Internal Module Connections...................................................................................................... 17
4 Configuration.................................................................................................................................... 20
JetStream Configuration............................................................................................................... 20
Audio Engine Configuration ........................................................................................................ 20
CommandBuilder Triggers........................................................................................................... 20
Device & Bus Addressing............................................................................................................. 21
Logitek Mosaic Reference Manual
Page 5
Modules ........................................................................................................................................ 21
Device Numbers .......................................................................................................................... 21
Wide Softkey Addressing ............................................................................................................. 21
Profanity Delay Operation .......................................................................................................... 22
Routing the Delay into the Air Chain ......................................................................................... 22
Router Positions on the Wide Softkey Panel.............................................................................. 22
Wide Softkey Bus Numbers & Screen Position Diagram .......................................................... 23
Using Command Builder to program the Router Positions ....................................................... 24
Variable Select Trigger Example .................................................................................................. 24
Route Select Trigger Example...................................................................................................... 25
Monitor Hotkey Addressing......................................................................................................... 27
Switched Meter Addressing (Meter Bridges only) ...................................................................... 28
Meter Bridge On Air and Mic Live Tally Lamps......................................................................... 28
Wrist Rest Glow Strip ................................................................................................................... 30
Changing Colors Of Fader On/Off Buttons ................................................................................ 31
Changing colors of Softkey Buttons ............................................................................................ 31
5 Operation .......................................................................................................................................... 32
The Fader Module (US/International) ......................................................................................... 33
The Fader Module (UK) ............................................................................................................... 34
Wide Softkey Module .................................................................................................................. 35
Monitor Module ........................................................................................................................... 36
GUEST/STUDIO section:............................................................................................................. 36
HEADPHONE section: ................................................................................................................ 36
MONITOR section:...................................................................................................................... 37
METER knob:................................................................................................................................ 37
TONE GEN section: ..................................................................................................................... 37
CUE section (UK PFL): ................................................................................................................. 38
6 Maintenance ..................................................................................................................................... 39
Warranty ....................................................................................................................................... 39
Firmware Updates........................................................................................................................ 39
Component Replacement ........................................................................................................... 39
Fader Replacement ...................................................................................................................... 39
Module swap-out ......................................................................................................................... 40
More Assistance............................................................................................................................ 40
Appendix A Release Notes ................................................................................................................. 41
Logitek Mosaic Reference Manual
Page 6
Known Issues ................................................................................................................................ 41
Appendix B Pinouts ............................................................................................................................... 42
To JetStream (DATA).................................................................................................................... 42
GPIs ............................................................................................................................................... 43
GPI Outputs.................................................................................................................................. 43
GPI Inputs ..................................................................................................................................... 43
Two Year Limited Warranty.................................................................................................................. 44
Logitek Mosaic Reference Manual
Page 7
1 Introduction
About this Manual
This manual describes the installation and operation of the Logitek Mosaic control surface.
Intended Audience
Intended Audience
Intended AudienceIntended Audience
This manual is aimed at Engineers responsible for installing, configuring and supporting a Logitek
Networked Console System with the Mosaic surface.
In the context of a system installation, or to become familiar with the entire Logitek Networked
Console System, the reader should also reference:
JetStream Reference Manual
AEConfig or JetSet Reference Manual
CommandBuilder Reference Manual
Manual Conventions
Manual Conventions
Manual ConventionsManual Conventions
The following conventions are used in this manual:
This text indicates a menu choice to be made, with an arrow separating a multi-level selection,
eg Control Panel
within Windows.
Indicates a “see
Indicates a “see----also” section in this manual, or another Logitek manual.
Indicates a “seeIndicates a “see
The exclamation symbol signifies an important note or critical information.
Users & Passwords. This can be a menu choice in a Logitek application, or
also” section in this manual, or another Logitek manual.
also” section in this manual, or another Logitek manual.also” section in this manual, or another Logitek manual.
Logitek Mosaic Reference Manual
Page 8
This text represents a command, script block example,
instruction to be typed, or directory path.
TIP: A useful tip from our knowledge base!
About the Mosaic
The Mosaic control surface from Logitek Electronic Systems brings you the flexibility of a router
based audio console system with the look, feel and easy handling that novice operators will
understand, and experienced console operators will appreciate.
The Mosaic offers full access to the sources available on Logitek’s JetStream routers, along with
simple bus selection and intuitive monitor controls. The Mosaic is compatible with the Logitek
Audio Engine provided that the engine has an AE-C6 card with version 3.77 or higher.
The Mosaic surface can be configured from 4 to 24 faders in 4 fader increments. There is also a
Monitor Module containing the monitoring functions and optional softkey and selector modules
may be added for additional flexibility. The module types include:
M2-FADER 4 Fader Module
M2-MONITOR Monitor Control Module
M2-NSOFT Narrow Softkey Button Module
M2-WSOFT Wide Softkey Button Module
In addition, the CL-METER Meter Bridge is available. The bridge can mount to the rear of the
console frame, or in split console configurations may be mounted to the countertop.
The main frame is available in a number of different sizes to accommodate the variety of fader
numbers. The frame is designed to be mounted on a desk for semi-permanent installation, but as no
cutouts are required it can easily be relocated.
Logitek Mosaic Reference Manual
Page 9
System Requirements
Mosaic is designed to connect to a Logitek JetStream running DSP version 4.x and above and the
AE-32 Audio engine using v3.87 or higher. Contact Logitek Electronic Systems or your reseller if
you are unsure of compatibility, or are adding a Mosaic surface to a pre-existing Logitek facility.
Sys tem Architecture
Sys tem Architecture
Sys tem Architecture S ystem Architecture
Surfaces Audio Engines Ethernet Switches
Console Surfaces
Control Panels
Surfaces are remote
control panels for
Audio Engine
Jetstream
Audio Engines
process Audio and
GPI control events
1 Audio
Net work
Network switches
distribute audio,
control & sync
Client PCs
internet
Software tools provide
remote control &
system maintenance
Remote Support
Software vTools
Console Surfaces
Control Panels
Business
Jetstream
2
Serial Comms IP TCP/IP
Figure 1 - Logitek System Architecture (v4.x)
Network
Software vTools
Software vTools
Serial
TCP/IP
UDP/IP
Put simply, the Mosaic surface is just a remote control panel for the JetStream. Unlike traditional
analog consoles, no audio passes through the Mosaic or its faders (with the exception of the cue
speaker audio). The Mosaic talks to the JetStream using the Logitek Command Protocol, with all
audio processing occurring inside the router.The mixing, routing and processing of audio is not
Logitek Mosaic Reference Manual
Page 10
dependent upon the embedded PC included with the JetNet Audio Networking Module. However,
additional functionality, such as macro buttons, scene snapshots, intercoms, delay control and
software tools interface to the system using the JetStream Server application that is bundled with the
module.
Compatibility Matrix
Compatibility Matrix
Compatibility MatrixCompatibility Matrix
Mosaic is designed for use with the JetStream Router v4.x and AE-32 Audio Engine v3.77 and
higher.
The Mosaic retains compatibility with other surfaces for the majority of its features.
Following is the minimum software release version/date that is required for Mosaic support.
Component General Support Additional Features
JSM-DSP Controller v1.41
JetStream Server v4.0
CommandBuilder v3.6
AEConfig v3.6
JetSet V1.0
Logitek Mosaic Reference Manual
Page 11
2 Unpacking
This section details what you should do when unpacking your newly arrived Mosaic surface.
Parts List
The exact list of parts received will vary depending on your order, but should generally include:
1 x Mosaic Power Supply
1 x fully assembled Mosaic frame, containing modules as ordered
1 x meter bridge assembly (option)
You will receive a parts list with the system that is specific to the modules on your order.
Unpacking
Carefully unpack the cartons whilst looking for any signs of shipping damage. You may wish to save
the shipping cartons until the operation of the system is verified.
Report any damage to the shipping carrier immediately. Verify that the contents of each box match
the packing list and report any discrepancies immediately to Logitek in writing.
Contacting Logitek
Contacting Logitek
Contacting LogitekC ontacting Logitek
In the event of a shipping problem, you can contact Logitek Electronic Systems in several ways:
U.S. Mail Logitek Electronic Systems, Inc.
5622 Edgemoor Drive
Houston, Texas 77081
USA
Telephone 877-231-5870
+1-713-664-4470 (outside U.S. and Canada)
Fax +1-713-664-4479
Email support@logitekaudio.com
Website www.logitekaudio.com
International customers should contact their local authorized Logitek dealer for assistance.
Logitek Mosaic Reference Manual
Page 12
3 Physical Installation
The Mosaic surface is designed to be mounted on a desk in a semi-permanent studio installation.
The Meter Bridge, if optioned, can be screwed to the back of the Mosaic.
Power Supply Unit
The Power Supply Unit is an external supply. It is one rack unit high and contains dual power
supplies with dual inlets.
There are two IEC connectors on the rear of the Power Supply Unit. A power cable is supplied only
for US installations. International customers may contact their reseller for the supply of power cables
if required.
As the power supplies are of switch-mode type, there is no voltage selection required.
There are also two DB-25 connectors on the back of the power supply. One is for GPI inputs and
the other is for GPI outputs.
Mosaic Frames
A number of Mosaic frame sizes are available, depending on the total number of faders. A fader
module is 4 slots wide. The monitor module and wide softkey module are 2 slots wide. The narrow
softkey module is one slot wide. Single slot blank panels are used to fill any gaps if required.
The frame will be shipped with the modules connected and fitted as ordered. These modules are
not intended to be moved, however Fader modules are interchangeable. The internal COM port
connections determine the device addressing for each modules.
The Mosaic frame is 20 inches (508 mm) deep and 3 inches (76.2 mm) high without meter bridge.
With a meter bridge, the frame is 7 ¼ inches (184.15 mm) high. Frame widths are as follows:
M2
M2----F10
F10 10
10 Slot Frame
M2M2
F10F10
14.75 inches (374.65 mm) wide
Slot Frame
1010
Slot FrameSlot Frame
Logitek Mosaic Reference Manual
Page 13
M2
M2----F12 12 Slot Frame
F12 12 Slot Frame
M2M2
F12 12 Slot FrameF12 12 Slot Frame
17.55 inches (445.77 mm) wide
M2
M2----F18
F18 18 Slot Frame
M2M2
25.95 inches (659.13 mm) wide
M2
M2----F22 22 Slot
M2M2
31.55 inches (801.37 mm) wide
M2
M2----F30 30 Slot Frame
M2M2
42.75 inches (1085.85 mm) wide
18 Slot Frame
F18F18
18 Slot Frame18 Slot Frame
F22 22 Slot Frame
F22 22 SlotF22 22 Slot
F30 30 Slot Frame
F30 30 Slot FrameF30 30 Slot Frame
Frame
FrameFrame
Meter Bridge (CL-Meter)
A hardware LED Meter Bridge is available as an option. The Meter includes two high-resolution
meters – one for Program bus and one switched.
TIP: If the Mosaic is powered on without being connected to the JetStream, no meter
LEDs will illuminate. This is normal operation; the center dot LEDs will turn on after
being connected to the JetStream and the rest of the LEDs will light as console
begins to receive meter data.
Mounting
Mounting
MountingMounting
The Meter option is supplied separately and attaches to the back of the Mosaic frame with
screws (included).
The RJ-11 cable from the Meter plugs into the Mosaic tray card at the far right into the jack
labeled “Meter.”
The Meter is hinged. Gently tighten the black center screw on the rear of the hinge to lock
the meter into place at the desired angle.
Logitek Mosaic Reference Manual
Page 14
Illustration 1: Mosaic 12 with CL-Bridge
Logitek Mosaic Reference Manual
Page 15
Connections
The Mosaic frame contains the control circuitry for the console. It connects to the Logitek
JetStream Router via a serial link. For redundancy, the control surface may be connected to two
JetStreams (main and backup)
IMPORTANT: At the time of this writing, the redundant JetStream feature has not
been fully developed. The JetStream does not currently support this
planned feature, and software updates to both JetStream and console
may be necessary once this future feature is finished.
AE-1:This is the main data connection. This RJ-45 cable connects to the surface port on the primary
JetStream router or Audio Engine. If only one router is in use, this is the only data connection
needed.
POWER: This RJ-45 cable provides power from the Mosaic Power Supply.
Logitek Mosaic Reference Manual
Page 16
AE-2: This is the backup data connection. The redundant JetStream feature is not currently
functional and this port should be left empty.
While we use RJ-45 patch cables to send data from the JetStream to the surface, this is RS-485 data
plus an AES pair for cue and not Ethernet data. Do not connect these data cables to a network
switch.
You can use a dedicated CAT5 patch cable or existing structured cabling for the data connection. If
using structured cabling systems, care should be exercised to ensure the serial connections are not
confused with other network outlets and that the link is not unintentionally “un-patched”.
The connection to the power supply should be a straight through RJ-45 connection and not pass
through wiring blocks or other interconnects for best results. The power cable between surface and
power supply passes 12 volts.
PSU
PSU
PSUPSU
The Mosaic is powered by a rack mounted external power supply included with the console. Dual
power inlets supply dual power supplies. A RJ-45 connector is used to send power and GPIO
information from the supply to the surface.
DB-25 connectors are provided on the Mosaic Power Supply for GPI Input and Output
connections. A ground lug is provided on the chassis for your convenience.
Logitek Mosaic Reference Manual
Page 17
GPIs
GPIs
GPIsGPIs
The Mosaic Surface has 12 GPI inputs and 12 GPI outputs for control of local studio devices.
GPI outputs are driven by optically-isolated, non-polarized, solid state switches, rated at 500ma to a
maximum voltage of 24V AC/DC, with surge to 2A. These solid state devices do not conduct at low
voltage, so cannot switch an audio input. However, they are suitable for most control signals, and
avoid problems with relay contacts being damaged by surges. Caution should be exercised to avoid
overloading the switches. If driving a high current device, we recommend using an external relay.
The GPI inputs are a current source to +3.3VDC that is pulled to ground to activate. This makes it
suitable for control by push-button, relay or open collector. A diode protects against static and over
voltage up to 18V. See the wiring diagram for polarity information if using non-standard activation
methods. A common ground is provided for input connection.
As wiring schemes vary from station to station, these cables are not supplied with the surface, but
are available from Logitek Electronic Systems or your local Logitek dealer.
See Appendix
See Appendix BBBB for
See Appendix See Appendix
for connector pinouts.
connector pinouts.
for for
connector pinouts.connector pinouts.
Internal Module Connections
Internal Module Connections
Internal Module ConnectionsInternal Module Connections
Inside the frame, four RJ11 port connectors are provided for connecting to each Fader module.
These are provided as a straight-through flat cable.
On small surfaces, there is one tray card. Faders connect to the appropriate ports marked 1-4, 5-8,
9-12, 13-16, 17-20.
The M2-NSOFT or M-2WSOFT connect to the RJ-11 port marked WSOFT.
The Monitor module connects to the RJ-11 port marked Monitor.
The Meter connects to the RJ-11 port marked Meter.
On large surfaces there are two tray cards, connected by an expansion cable. In large frames, this is
mounted to the same tray. In split frame consoles, one card is in each tray, and the expansion cable
connects the two frames.
Logitek Mosaic Reference Manual
Page 18
On the left frame, connect the appropriate faders to jacks 1-4, 5-8, 9-12, 13-16. The W-SOFT port
may be used for the Wide Softkey panel. The Mixer A1 In port is used to connect M2-NSOFT
narrow softkey panels. The device number for this panel would be device 2d on port 1 (55 on port
2). The Mixer A3 In port is used to connect a second M2-NSOFT narrow softkey panel (device 2f
port 1, 57 port 2). The meter bridge port is used to connect the external meter bridge.
On the right frame, connect the appropriate faders to jacks 9-12, 13-16, 17-20, and 21-24. The
WSOFT port is for the M2-WSOFT module. The monitor is for the M2-MON module. The meter
bridge port is for the external bridge.
Note that some fader ports, the wide soft port, and the meter bridge port appear on both tray cards.
These ports share the same addresses. Use the port closest to where the module is installed. The
ports are duplicated for the purpose of split frame configurations. Two duplicate expansion jacks are
on the right hand card; use the jack that is most convenient to connect either the two tray cards
within one frame or the two tray cards between split frames.
The following diagram shows the different card configurations.
Logitek Mosaic Reference Manual
Page 19
Logitek Mosaic Reference Manual
Page 20
4 Configuration
This chapter covers basic configuration information, relating specifically to the Mosaic surface.
JetStream setup and configuration is covered in detail in the following manuals:
Logitek JetStream Reference Manual
Logitek AEConfig Reference Manual
JetStream Configuration
Configuration of the JetStream Router is done in JetSet.
See the JetStr
See the JetStream Reference Manual f or information on configuring JetStreams
See the JetStrSee the JetStr
Audio Engine Configuration
Configuration of the Audio Engine is done in AE Config.
Set the port that the console will be connected to on the Hardware Configuration page to accept a
Mosaic console with the appropriate number of faders.
The picture that AE Config will draw will be the previous generation of Mosaic, but the addressing
and features will be the same.
See the Audio Engine Reference Manual for information on configuring Audio
See the Audio Engine Reference Manual for information on configuring Audio
See the Audio Engine Reference Manual for information on configuring Audio See the Audio Engine Reference Manual for information on configuring Audio
Engin
Engines.
EnginEngin
es.
es.es.
eam Reference Manual for information on configuring JetStreams
eam Reference Manual for information on configuring JetStreamseam Reference Manual for information on configuring JetStreams
CommandBuilder Triggers
The Mosaic surface contains many programmable buttons and features. These features are scripted
in “triggers” in CommandBuilder, and executed by JetStream Server.
See the CommandBuilder User’s Manual for information on w riting
See the CommandBuilder User’s Manual for information on w riting Triggers.
See the CommandBuilder User’s Manual for information on w riting See the CommandBuilder User’s Manual for information on w riting
Triggers.
Triggers.Triggers.
Logitek Mosaic Reference Manual
Page 21
The CommandBuilder manual includes details and examples of Mosaic specific features, such as
Monitor Hotkeys, Softkey Buttons and more. The programming of these features does require a
certain level of familiarity with the system. If you need assistance, please contact Logitek Electronic
Systems or your reseller.
Device & Bus Addressing
Each device (such as a fader input or button panel) requires its own Device Number. Within that
device, each button, lamp and feature has a Bus Number. Together, the Device and Bus Numbers
allow the JetStream and Surface to communicate.
When configuring the Mosaic’s programmable buttons in CommandBuilder, you will require the
Device Number and Bus Number for each button or lamp. The information below will help you
determine the addressing scheme in use on your Mosaic.
Modules
Modules
ModulesModules
Module How Addressing is determined Max Modules Supported
Mosaic-MON Uses the standard Monitor, Headphones, Guest/Studio & Cue Gain addressing 1
Mosaic-FADER Device Set determined by COM port allocation (pre-defined) 6 modules (24 faders)
Mosaic-METER Uses standard PGM Meter addressing 1
Device Numbers
Device Numbers
Device NumbersDevice Numbers
In Mosaic v1.x the Device Number of a module is determined by its firmware and position.
Wide Softkey Addressing
The twelve softkeys at the top of the wide softkey module follow the Numix Bridge Button
addressing scheme, therefore the Bridge Button and Bridge Lamp keywords in Command
Builder may be used.
The softkey buttons for a console connected to JetStream port 1 are on device 28 and the lamps are
on device 27. For port 2, use device 50 for buttons and 4F for lamps. For port 3, use device 64 for
buttons and 63 for lamps. Bus numbers are 32-43.
Logitek Mosaic Reference Manual
Page 22
For example, button #1 on a console connected to JetStream port 1 is device 28 bus 32 and
its corresponding lamp is device 27 bus 32. Alternatively, it is valid to address button #1 on
port 1 as surf 1 bridgebutton 1 and its corresponding lamp as surf 1 bridgelamp 1.
Command Builder will translate those keywords into the appropriate device and bus numbers.
The exception to buttons on the Wide Softkey being device 27 is the set of buttons for profanity
delay control. These buttons are on device 30 (Router 1 In). If on port 2, it would correspond to
device 58.
Profanity Delay Operation
Unlike other Logitek audio consoles, Command Builder triggers are not required to make the
profanity delay function on the Mosaic console. Pressing the In button sends a start command to the
delay, pressing the Out button sends a stop command to the delay system, and pressing the dump
button sends a Dump command. If you need additional commands to fire off of those functions,
you may write commands to device 30, bus 24, 25, and 27 for the appropriate buttons, but you do
not need to write TALK START, TALK STOP, and TALK DUMP commands. The delay time will
appear in the window automatically.
Routing the Delay into the Air Chain
Routing the Delay into the Air Chain
Routing the Delay into the Air ChainRouting the Delay into the Air Chain
In Surface Settings in your router configuration software, make sure you have routed Program Out
into Router 1 In. In your Output Selections in the router configuration software, route Port(x) Router
1 Out into any output that should get delay, such as transmission. Port(x) Program Out will be pre-
delay audio and should be routed anywhere that needs pre-delay audio, such as music on hold for
telephone hybrids, monitors and headphones.
Router Positions on the Wide Softkey Panel
The Wide Softkey Panel offers 8 router positions that can be used to change routes to devices such
as remote codecs, audio recorders, IFB systems, or any other purpose. These selectors are
programmed using Command Builder. A discussion of how to do this follows after the diagram.
Logitek Mosaic Reference Manual
Page 23
Wide Softkey Bus Numbers & Screen Position Diagram
Logitek Mosaic Reference Manual
Page 24
Using Command Builder to program the Router Positions
There are two types of triggers that may be used to program the WSOFT routers: Variable Select
and Route Select.
A Variable Select allows you to perform multiple commands, including routes, from a pick list. The
pick list is defined as part of the trigger.
A Route Select allows you to choose a destination on the router and route any allowed source to
that destination. The pick list is defined by the sources ticked as allowed in the Output Selections
page of the configuration software.
The Command Builder manual defines these commands in further detail. There are special
keywords that should be used in these triggers. An example of each type of trigger is provided
below. When you look in the manual, you will see that there is a MOSAIC keyword in both
Variable Select and Route Select commands, however that is used with the first generation console
and not this board. We will use the DISPLAY keyword and the new SOURCENAME keyword
instead to make the magic happen.
Var iable S elect Trigger Example
Var iable S elect Trigger Example
Var iable S elect Trigger ExampleVar iable S elect Trigger Example
This trigger assumes that a variable called “ISDN1” has been defined on the System Page of
Command Builder.
We used channel notation in this trigger table instead of s[source] and d[destination] as is more
commonly used in Command Builder. When using channel notation, you write the source as its hex
address and you take the destination’s hex address, convert it to decimal, subtract 10 and you get
the channel number. [Why? Because a programmer said so.] In our little test world, our ISDN is
connected to destination device 6E. That converts to decimal 110, subtract 10 and you get channel
100. The sources we’re routing are program (device BE), Aux 1 (device BF), and Mix Minus 1
(device C7). We know those addresses either by looking in the programming spreadsheet available
from support or by looking at the pop-out list on the JetStream State page in JetStream Server.
Needless to say, if you can use s[source] and d[destination] notation in Command Builder, it’s
easier. You still need to know that the text on the screen is device27 (assuming we’re on port 1) and
that the button is on device 28.
Logitek Mosaic Reference Manual
Page 25
If you know your way around triggers, you’ll notice that we turn on the lamp for our button when
we begin but do not turn it off on ACCEPT. The console is smart enough to do that for you. We do
turn the lamp off on CANCEL just to give Cancel something to do. Finally, don’t skip the IF CANCEL
WAIT section, or else Command Builder will throw an error. You can adjust the number of seconds
you have to make a selection before it all times out by adjusting the WAIT time on the IF CANCEL.
Text after a tilde ~ is a comment
tri gger ae1 device28 bus 79 on
cmd ae1 text device27 line11 "ISDN1 Select" ~ writes text to the bottom line of screen 1
cmd ae1 vISDN1 set selection mode display ( device 28 screen 1 ) ~ activates selection screen
cmd ae1 text selection 1 "Program"
cmd ae1 text selection 2 "Aux 1"
cmd ae1 text selection 3 "Mix Minus"
if accept selection = 1
cmd ae1 route device BE to chan 100 ~ pgm is source 00be; channel 100 translates to destination 006E
cmd ae1 sourcename device6E display ( device27 line12 pos1 )
endif
if accept selection = 2
cmd ae1 route device BF to chan 100 ~ aux 1 is source 00bf; channel 100 translates to destination 006E
cmd ae1 sourcename device6E display ( device27 line12 pos1 )
endif
if accept selection = 3
cmd ae1 route device c7 to chan 100 ~ mm1 is source 00c7; channel 100 translates to destination 006E
cmd ae1 sourcename device6E display ( device27 line12 pos1 )
endif
if cancel wait 5
cmd ae1 device27 bus79 off
endif
In our example, we only routed the source and wrote the name of the source to the screen.
If you wanted to do more, like pulse relays or send text to other studios, you would place those
commands before the ENDIF that closes the IF ACCEPT or IF CANCEL WAIT.
Route Select Trigger Example
Route Select Trigger Example
Route Select Trigger ExampleRoute Select Trigger Example
The Route Select is a lot simpler than the Variable Select. All you really need to know here is the
device number where you want to change the route, and you need some sources allowed in
Logitek Mosaic Reference Manual
Page 26
Output Selections in the config software so it knows what to pick. Also, you need to set a variable
that is unique to the trigger so Command Builder has a place to hang the selection.
The surface takes care of all of the lamps in this trigger. Putting the lamp off command in the IF
CANCEL WAIT gives that if statement something to do.
In our example, we are changing routes on destination device 70 and we’re using a variable set on
the Command Builder system page called ISDN2.
trigger ae1 device28 bus 80 on
cmd ae1 text device27 line 21 "ISDN2"
cmd ae1 vISDN2 set route selection mode device70 display ( device27
screen 2 )
if cancel wait 5
cmd ae1 device27 bus80 off
endif
Logitek Mosaic Reference Manual
Port Number
Monitor
Headphones
Studio
1
Device 24
Device 25
Device 23
2
Device 4C
Device 4D
Device 4B
3
Device 62
Device 65
Device 61
Page 27
Monitor Hotkey Addressing
There are four monitor hotkeys that may be addressed in Command Builder to route sources to the
control room monitors, headphones, and studio monitors.
The buttons are labeled SEL1, SEL2, SEL3, and SEL4.
SEL 1 is bus 16. SEL 2 is bus 17. SEL 3 is bus 18, and SEL4 is bus 19.
The device numbers are as follows:
Alternatively, d[device] notation in Command Builder, such as d[Port1 Monitor In] is
valid and will be properly translated by Command Builder.
Logitek Mosaic Reference Manual
Port (Surface) Number
Device Number
1 2c 2 54 3 6a
Port (Surface) Number
Device Number
1 27 2 4F 3 63
Page 28
Switched Meter Addressing (Meter Bridges only)
The Switched meter defaults to displaying whatever source is routed to Monitor In. When bus 0 is
turned on for the Monitor Meter in device, the meter will switch to whatever source is routed to the
Monitor Meter In.
Monitor Meter In Device Numbers:
To choose which sources are selectable by the switched meter, place checkmarks in the MON MTR
column in Surface Settings in the configuration software.
Bus 0 for the monitor meter device must be switched via triggers in Command Builder. It can be
forced on at reset or it may be turned on and off with a softkey button as desired.
Meter Bridge On Air and Mic Live Tally Lamps
Two tally LEDs are provided on the meter bridge. The Mic Live tally may be used to tell the
operator that the mic is on. The On Air tally may be used to tell the operator that the console has
been switched to air. The bus number of the Mic Live LED is 17 and the On Air LED is 18. The
device numbers are in the chart below.
Device Numbers for Mic Live and On Air Tally Lamps
Logitek Mosaic Reference Manual
Page 29
Because these LEDs are on the same device number as console GPI outputs, an easy way to
program the Mic Live lamp is to enter 117 into the Mute Tally box for each Mic on port 1. For port
2 consoles, use 217. For port 3 consoles, use 317.
Logitek Mosaic Reference Manual
Page 30
Wrist Rest Glow Strip
Multi-colored LED lights are mounted under the wrist rest. These lamps have a foreground color
and background color. They are addressed as device 27 on port 1 (device 4F on port 2, device 63
on port 3); the background color is turned on with bus 19 and foreground color is turned on with
bus 20. If the background color bus and foreground color bus are turned on at the same time, the
foreground color will show.
The glow strip can be set to change with the microphone state. We suggest turning on device 27
bus 19 in the init or engine reset trigger in Command Builder and then entering 120 into the mute
tally box in the config software. [For port 2, use device 4f bus 19 and 220 in the mute tally box; for
port 2 use device 63 bus 19 and 320 in the mute tally box.]
To turn the lamps off, turn off both bus 19 and 20.
To set the foreground color, put this command in the init triggers in Command Builder:
cmd ae1 device27 chon set color mosaic RGB000015
To set the background color, put this command in the init triggers in Command Builder:
cmd ae1 device27 choff set color mosaic RGB001500
Adjust device numbers based on the port the console is connected to. RGB values listed below.
These commands could also be placed in different triggers outside of the init/reset as desired.
Red RGB150000 Purple RGB030015
Green RGB001500 Light Aqua RGB021411
Blue RGB000015 Dark Aqua RGB000915
White RGB151515 Orange RGB151200
Crimson RGB040000 Yellow RGB091500
Blue White RGB041215 Magenta RGB150015
Logitek Mosaic Reference Manual
Page 31
Other custom color combinations may be created by changing the RGB values (valid 00 – 15) but
these colors seem to look the best.
Changing Colors Of Fader On/Off Buttons
The same Set Channel Color command used by the Series 1 Mosiac console described on page
139 of the Command Builder manual applies. The flash command listed on that page also applies.
cmd ae1 fader 1 choff set color mosaic RGB000015
cmd ae1 fader 1 chon set color mosaic RGB001500
The RGB values listed for the wrist rest glow strip apply for the on/off buttons.
Changing colors of Softkey Buttons
The 12 softkey buttons at the top of the wide softkey panel and 12 narrow softkey buttons may
have their colors changed via assembly language commands in Command Builder.
The command has the general format of:
cmd ae1 asm “02 06 b1 27 bb 07 RG B0”
where
bb = bus number of button expressed in hex (20 – 2b)
R = red brightness 0 – F (hex)
G = green brightness 0 – F (hex)
B = blue brightness 0 – F (hex)
For narrow softkey panels, adjust the device number (27) to reflect the device number of the port
where the narrow softkey is connected.
Logitek Mosaic Reference Manual
Page 32
5 Operation
Your Logitek Mosaic console has been designed for easy and quick access to the functions you most
need. If you’ve had experience with broadcast consoles before, you’ll soon be at home, finding
your way around quite easily.
Logitek Electronic Systems has been manufacturing broadcast consoles for decades, so we
understand how to make control surfaces that are both powerful and straightforward. During the
design of the Mosaic, customers and operators provided feedback that helped shape the final
product. So we’re confident you’ll find the Mosaic a joy to use on-air.
Following is a look at each of the Mosaic modules, and how the standard functions are used.
Logitek Mosaic Reference Manual
Page 33
The Fader Module (US/International)
All
All functions for each fader are done at each channel. A
multi-function select knob toggles between modes.
Buttons:
ON: Turns on the channel
OFF: Turns off the channel
Pgm: When lit, program bus is assigned to fader
A1: When lit, aux 1 is assigned to fader
A2: When lit, aux 2 is assigned to fader
A3: When lit, aux 3 is assigned to fader
A4: When lit, aux 4 is assigned to fader
IN: Toggles to last route
TB: Engages talkback to sources with associated mix minus
bus. If pressed for less than a half second, this latches. If
pressed for more than a half second, it becomes
momentary and will turn off after the button is released.
Cue: Turns on the cue bus
Select knob modes:
Route: This is the default mode, and the select knob will glow light
blue. Turn the knob to select a source on the bottom OLED screen.
Press TAKE to change the route. Press CANCEL to abort changing the
route. If the fader is on, this function is locked out.
Trim/Pan/Mode/Effects: When pressed, the knob will glow magenta
and a cursor will appear on the top OELD screen. On the top line is
trim. Turn the knob to adjust the fader’s trim, from -10 to +10 dB.
Press the knob to move to the second line to adjust pan from left to
right. Press the knob again to advance the cursor to the third line to
adjust mode (Stereo/Mono/Phase/LL/RR/Lx/xR). Press the knob again to
advance to the bottom line to adjust effects. On this line, turn the knob
to choose which effect to adjust (or << to go back). When you get to
the effect you wish to change, press the knob to choose it and turn to
adjust. CANCEL will exit the menu and TAKE has the same effect as
pressing the knob.
Logitek Mosaic Reference Manual
Page 34
The Fader Module (UK)
All
All functions for each fader are done at each channel. A
multi-function select knob toggles between modes. As is
customary with UK consoles, the channel turns on and off
with fader movement.
Buttons:
START: Machine start
PFL: Pre-Fader listen.
Pgm: When lit, program bus is assigned to fader
A1: When lit, aux 1 is assigned to fader
A2: When lit, aux 2 is assigned to fader
A3: When lit, aux 3 is assigned to fader
A4: When lit, aux 4 is assigned to fader
IN: Toggles to last route
TB: Engages talkback to sources with associated mix minus
bus. If pressed for less than a half second, this latches. If
pressed for more than a half second, it becomes
momentary and will turn off after the button is released.
Cue: Turns on the cue bus
Select knob modes:
Route: This is the default mode, and the select knob will glow light
blue. Turn the knob to select a source on the bottom OLED screen.
Press TAKE to change the route. Press CANCEL to abort changing the
route. If the fader is on, this function is locked out.
Trim/Pan/Mode/Effects: When pressed, the knob will glow magenta
and a cursor will appear on the top OELD screen. On the top line is
trim. Turn the knob to adjust the fader’s trim, from -10 to +10 dB.
Press the knob to move to the second line to adjust pan from left to
right. Press the knob again to advance the cursor to the third line to
adjust mode (Stereo/Mono/Phase/LL/RR/Lx/xR). Press the knob again to
advance to the bottom line to adjust effects. On this line, turn the knob
to choose which effect to adjust (or << to go back). When you get to
the effect you wish to change, press the knob to choose it and turn to
adjust. CANCEL will exit the menu and TAKE has the same effect as
pressing the knob.
Logitek Mosaic Reference Manual
Page 35
Wide Softkey Module
The wide softkey module provides 12 large user-defined buttons at the top
of the module, 8 router positions, delay control, and 8 small user-defined
buttons at the bottom of the module.
To operate the router, press the select button at the desired OLED screen
and turn the select knob to pick the desired option. Press TAKE to accept
the selection or CANCEL to abandon it.
To operate the delay, press IN to ramp in to the delay, press OUT to ramp
out of the delay, and press DUMP to dump the buffer.
Programming information for this module is provided in the previous
chapter.
Logitek Mosaic Reference Manual
Page 36
Monitor Module
The monitor module controls all monitoring functions:
GUEST/STUDIO s ection:
GUEST/STUDIO s ection:
GUEST/STUDIO s ection:GUEST/STUDIO s ection:
TB button: inserts the Talkback Mic (as defined in JetSet/AE Config Surface
Settings) into the Guest/Studio monitor bus
FOL MON: When turned on, the route to GUEST/STUDIO will follow
routing changes to the MONITOR section.
MUTE: mutes the Guest/Studio monitor bus.
To change the route, press on the Guest/Studio knob. The knob will turn
green and the take light will light up. Turn the knob until you see what you
would like to listen to. Press Take to accept. To cancel, press the
Guest/Studio knob again. It will exit the mode and turn blue. If FOLLOW
MONITOR is engaged, changing the route with the knob will turn
FOLLOW MONITOR off.
When the knob is blue, it controls the volume.
SEL1 – SEL4 buttons: when pressed, these will change the route to the
Guest/Studio monitor bus if they were programmed via Command Builder
as described in the previous chapter.
HE ADPHONE
HE ADPHONE section:
HE ADPHONEHE ADPHONE
MONO: sets the headphones to mono
FOL MON: When turned on, the route to the headphones will follow
routing changes to the MONITOR section.
SPLIT: Sends the bus being monitored to the left and cue to the right.
To change the route, press on the Headphone knob. The knob will turn
green and the take light will light up. Turn the knob until you see what you
would like to listen to. Press Take to accept. To cancel, press the
Headphone knob again. It will exit the mode and turn blue. If FOLLOW
section:
section: section:
Logitek Mosaic Reference Manual
Page 37
MONITOR is engaged, changing the route with the knob will turn FOLLOW MONITOR off.
When the knob is blue, it controls the volume.
SEL1 – SEL4 buttons: when pressed, these will change the route to the Headphone monitor bus if
they were programmed via Command Builder as described in the previous chapter.
MO NITOR section:
MO NITOR section:
MO NITOR section:MO NITOR section:
5.1: Puts the monitor speakers in 5.1 mode. (not currently supported)
MONO: Puts the monitor speakers in mono mode
DIM: reduces the volume to the monitor speakers
MUTE: mutes the monitor speakers
To change the route, press on the Monitor knob. The knob will turn green and the take light will
light up. Turn the knob until you see what you would like to listen to. Press Take to accept. To
cancel, press the Headphone knob again. It will exit the mode and turn blue.
When the knob is blue, it controls the volume.
SEL1 – SEL4 buttons: when pressed, these will change the route to the control room monitor bus if
they were programmed via Command Builder as described in the previous chapter.
ME TER knob:
ME TER knob:
ME TER knob:METER knob:
Turning this knob changes selections in the switched meter on the meter bridge. See the previous
chapter to learn how to configure and enable/disable the switched meter.
TO NE GEN section:
TO NE GEN section:
TO NE GEN section:TO NE GEN section:
Changes the frequency of the JetStream’s built in tone generator between 10K, 1K, 400 Hz, or an
ID (recorded audio file). The ID feature is a planned feature for future development and is not
currently in operation. The tone generator is currently supported.
Logitek Mosaic Reference Manual
Page 38
CU E section (UK PFL):
CU E section (UK PFL):
CU E section (UK PFL):CU E section (UK PFL):
The knob changes the volume of the Cue bus. The TO MONITOR button inserts the CUE bus into
the control room monitors. On UK consoles, this section is labeled PFL.
Logitek Mosaic Reference Manual
Page 39
6 Maintenance
The Mosaic uses multi-layer boards with surface mount technology. As such, the majority of the
console is not user-serviceable. However, there are some basic tasks that can be performed by
suitably qualified technical personnel.
Warranty
Logitek Electronic Systems will honor the warranty of the system when conducting field
maintenance, provided:
Repairs or updates only relate to recommended and documented procedures
Care is taken and procedures are followed
Repairs are conducted by suitably trained or experienced service personnel
If you do not feel comfortable performing maintenance or repairs, please do not proceed. If you
would like advice prior to attempting a repair, please contact Logitek Electronic Systems or your
reseller.
Firmware Updates
Each module strip has internal memory that is field upgradeable. Logitek Electronic Systems or
your local Logitek dealer may from time-to-time supply firmware updates to add new features or fix
bugs.
Component Replacement
The Mosaic uses standard faders which can be replaced by station technicians.
Fader Replacement
Fader Replacement
Fader ReplacementFader Replacement
The Mosaic uses a Penny & Giles fader.
Model No. PGF3210/D/U/--A
Logitek Mosaic Reference Manual
Page 40
No audio is carried through the fader, just control signals. The fader can be easily replaced with a spare from
Logitek or an electronics supplier.
To replace a fader:
1. Remove the four screws from the required module.
2. Carefully remove the module from the frame.
3. Disconnect the fader from the main board.
4. Remove the slider cap.
5. Remove the two hex screws that mount the fader to the module.
6. Fit the replacement fader to the module using the two hew screws.
7. Replace the slider cap.
8. Reconnect the fader connector, ensuring the same polarity as the other faders on the
module.
9. Replace the module in the frame, and screw it back in.
Module swap
Module swap----out
Module swapModule swap
out
outout
If you need to swap a module with an on-site spare, you can simply unscrew the module,
disconnect it, connect the replacement and screw it in. Modules are fully hot-swappable – they will
refresh their status shortly after powering up.
Mor e Assistance
Mor e Assistance
Mor e AssistanceMor e Assistance
If you would like more assistance with maintenance and service, please contact Logitek or your
reseller.
Logitek Mosaic Reference Manual
Page 41
Appendix A Release Notes
Known Issues
The following issues have been reported and are under investigation.
There are no known issues at this writing.
Logitek Mosaic Reference Manual
Page 42
Appendix B Pinouts
To JetStream (DATA)
Connection to the JetStream is via a RJ45 connector mounted on the rear of the frame. Straight
through CAT5 cabling is used.
Pin Connection
1 Cue -
2 Cue +
3 RS485 RX-
4 RS485 TX5 RS485 TX+
6 RS485 RX+
7 No connect
8 Ground
Logitek Mosaic Reference Manual
Page 43
GPIs
GPI connections are on two DB25 connectors on the power supply. One DB-25 is for inputs and
one is for outputs. We recommend terminating GPIs to Krone style or M66 termination blocks.
GPI Outputs
GPI Outputs
GPI Inputs
GPI Inputs
GPI Inputs GPI Inputs
Pin Connection Pin Connection
1 GPI In 1 14 Ground
2 GPI In 2 15 Ground
3 GPI In 3 16 Ground
4 GPI In 4 17 Ground
5 GPI In 5 18 Ground
6 GPI In 6 19 Ground
7 GPI In 7 20 Ground
8 GPI In 8 21 Ground
9 GPI In 9 22 Ground
10 GPI In 10 23 Ground
11 GPI In 11 24 Ground
12 GPI In 12 25 Ground
13 No Connect
GPI OutputsGPI Outputs
Pin Connection Pin Connection
1 GPI Out 1A 14 GPI Out 1B
2 GPI Out 2A 15 GPI Out 2B
3 GPI Out 3A 16 GPI Out 3B
4 GPI Out 4A 17 GPI Out 4B
5 GPI Out 5A 18 GPI Out 5B
6 GPI Out 6A 19 GPI Out 6B
7 GPI Out 7A 20 GPI Out 7B
8 GPI Out 8A 21 GPI Out 8B
9 GPI Out 9A 22 GPI Out 9B
10 GPI Out 10A 23 GPI Out 10B
11 GPI Out 11A 24 GPI Out 11B
12 GPI Out 12A 25 GPI Out 12B
13 No Connect
Two Year Limited Warranty
Logitek Electronic Systems, Inc. warrants its professional equipment (excluding Logitek Software,
which is covered by a separate warranty) against defects in materials and workmanship for two years pursuant
to the following terms and conditions. The warranty extends to the original purchaser only.
LOGITEK will repair or replace, at its option, at its factory without charge professional equipment if a
defect in materials or workmanship develops during the first two years following purchase, when the equipment is returned to the
factory or LOGITEK authorized service centers freight prepaid with a description of the nature of the failure. No reimbursements can
be made for repair charges that are not factory authorized. After repair or replacement, LOGITEK will return the equipment to the
purchaser freight prepaid.
In the event that any part of this professional equipment becomes defective during the first two years
following purchase, and purchaser wishes to attempt repair, purchaser may obtain a replacement part by
notifying LOGITEK of the part of the equipment which has failed. LOGITEK will thereafter ship a replacement
part, freight prepaid. LOGITEK may require the purchaser to return the defective part to LOGITEK freight
prepaid as a condition of such replacement, either before or after LOGITEK ships the replacement part.
LOGITEK shall not be responsible for any other charges or liabilities associated with purchaser-made repairs.
No part or equipment shall be considered defective if it fails to operate due to exposure to extreme
temperatures or excessive moisture in the atmosphere.
Light bulbs, batteries, potentiometers or other equipment not manufactured by Seller shall carry only
the warranty, if any, of the original equipment manufacturer in effect at the time of shipment of this order; and
Seller’s obligation under this warranty shall be limited to such adjustment as Seller may obtain from the original
manufacturer.
This limited warranty is void if equipment is modified or repaired without authorization; subjected to
misuse, abuse, accident, water damage or other neglect; or has had its serial number defaced or removed.
No obligation is assumed by LOGITEK to update previously manufactured equipment. Specifications
are subject to change without notice. EXCEPT AS SPECIFICALLY PROVIDED HEREIN, LOGITEK MAKES NO WARRANTY,
REPRESENTATION, PROMISE, OR GUARANTEE, EITHER EXPRESS OR IMPLIED, STATUTORY OR OTHERWISE, WITH RESPECT
TO THE EQUIPMENT, USER DOCUMENTATION OR RELATED TECHNICAL SUPPORT, INCLUDING THEIR QUALITY,
PERFORMANCE, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT WILL LOGITEK BE LIABLE
FOR INDIRECT, SPECIAL, INCIDENTAL, TORT, ECONOMIC, COVER, OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE
USE OF OR INABILITY TO USE LOGITEK PRODUCTS, EQUIPMENT, OR SERVICES, INCLUDING, WITHOUT LIMITATION,
DAMAGES OR COSTS RELATING TO THE LOSS OF PROFITS, BUSINESS, GOODWILL, DATA OR COMPUTER PROGRAMS,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO CASE SHALL LOGITEK ‘S LIABILITY FOR MONEY
DAMAGES EXCEED THE AMOUNT PAID BY YOU FOR THE LOGITEK EQUIPMENT OUT OF WHICH SUCH CLAIM AROSE. THE
FOREGOING LIMITATIONS SHALL NOT APPLY TO CLAIMS RELATING TO DEATH OR PERSONAL INJURY WHICH ARISE OUT
OF PRODUCTS DEEMED TO BE CONSUMER GOODS UNDER APPLICABLE LAW.
Some states or provinces do not allow the exclusion or limitation of implied warranties or limitation of liability for incidental or
consequential damages, so the above exclusion or limitation may not apply to you.
The warranty and remedies set forth herein are exclusive and in lieu of all others, oral or written,express or implied. No Logitek
dealer, distributor, agent, or employee is authorized to make any modification or addition to this warranty.
Loading...