Slimline Dishwasher
Installation / Instruction Manual
LDW45S11
LDW45S11_IB_110331.indd 1 3/31/11 5:04 PM
LDW45S11_IB_110331.indd 2 3/31/11 5:04 PM
3
Contents
Unpacking ..................................................................................................................................... 5
Installation .................................................................................................................................... 6
Location .......................................................................................................................................................................6
Product Overview .......................................................................................................................10
Front View ................................................................................................................................................................10
Rear View ..................................................................................................................................................................10
Upper Basket ...........................................................................................................................................................11
Lower Basket ...........................................................................................................................................................11
Internal View............................................................................................................................................................11
Control Panel ...........................................................................................................................................................12
Wash Cycle Table ......................................................................................................................... 13
Before Operating ........................................................................................................................ 14
To Open the Door .................................................................................................................................................. 14
To Close the Door ..................................................................................................................................................14
Items Not Suitable for Use in the Dishwasher ............................................................................................. 14
Adding Detergent or Detergent Tablet ..................................................................................... 15
Adding Rinse Aid ........................................................................................................................16
Adjusting the Rinse Aid Reservoir ................................................................................................................... 16
Adding Salt ..............................................................................................................................................................17
Adjusting Salt Consumption .............................................................................................................................18
Loading the Dishwasher ............................................................................................................19
Before Loading the Dishwasher ....................................................................................................................... 19
Upper Basket ........................................................................................................................................................... 20
- Adjusting the Upper Basket .................................................................................................................... 20
- Loading the Upper Basket for 12 Place Settings ............................................................................. 20
- Hinged Cup Rack ........................................................................................................................................21
Lower Basket ........................................................................................................................................................... 21
- Hinged Spikes .............................................................................................................................................. 21
- Loading the Lower Basket .......................................................................................................................22
Cutlery Basket ......................................................................................................................................................... 22
- Loading the Cutlery Basket .....................................................................................................................22
Starting a Wash Cycle .................................................................................................................23
Changing a Programme ............................................................................................................. 23
At the End of a Programme ........................................................................................................ 23
Switching O the Unit ................................................................................................................ 24
Unloading the Dishwasher ........................................................................................................ 24
Delay Start ................................................................................................................................... 24
Half Load .....................................................................................................................................24
Cleaning After Use ...................................................................................................................... 25
External Care ...........................................................................................................................................................25
- The Door and the Door Seal ................................................................................................................... 25
- The Control Panel ....................................................................................................................................... 25
Internal Care ............................................................................................................................................................ 25
- Filtering System ...........................................................................................................................................25
- Spray Arms .................................................................................................................................................... 26
LDW45S11_IB_110331.indd 3 3/31/11 5:04 PM
4
Frost Precaution ......................................................................................................................... 26
Moving the Dishwasher .............................................................................................................26
Maintenance After a Prolonged Period of Non-Operation ..................................................... 26
Hints and Tips ............................................................................................................................. 27
Fault Code ................................................................................................................................................................ 27
Technical Problems ............................................................................................................................................... 27
Disposal of the Dishwasher ....................................................................................................... 29
Disposal of Packing Material ..................................................................................................... 29
Specications .............................................................................................................................. 30
Safety Warnings .......................................................................................................................... 31
LDW45S11_IB_110331.indd 4 3/31/11 5:04 PM
5
Unpacking
Remove all packaging from the unit. Retain the packaging. If you dispose of it please do so according to
local regulations.
The following items are included:
The Main Unit
Detergent Measuring Spoon x 1
1 full spoon = 20g (approx.)
P.N.: 673002200079
Instruction Manual X 1
P.N.: LDW45S11-000
U-shape Hose Holder X 1
P.N.: 673006200003
Salt Funnel X 1
P.N.: 673002200043
Condensation Strip X 1
P.N.: 675001300715
Measuring Cup X 1
60ml (approx)
P.N.: 673006200004
Water Supply Hose X 1
P.N.: 673000900060
Cutlery Basket
P.N.: .673002200080
Power
Delay
Start
1/2 Load
3in1 Intensive Normal Eco Rinse Glass Rapid
Thank you for purchasing your new Logik Slimline Dishwasher.
These operating instructions will help you use it properly and safely.
We recommend that you spend some time reading this installation/instruction manual
in order that you fully understand all the operational features it offers.
Read all the safety instructions carefully before use and keep this installation/
instruction manual for future reference.
If items are missing, or damaged please contact Partmaster (UK only).
Tel: 0844 800 3456 for assistance.
This product has been wet tested to ensure correct operation.
As a result some water may remain inside the unit. This is
normal and safe. Remove any water droplets from the exterior
if necessary.
Slimline D ishwasher
Installation / Ins truction Ma nual
LDW45S11
LDW45S11_IB_110331.indd 5 3/31/11 5:04 PM
6
INSTALLATION
450
580
unit in mm
850
30
850
450
620
min.100
80
450
580
850
30
850
450
620
min.100
80
level
level
level
level
Power
Delay
Start
1/2 Load
3in1IntensiveNormal EcoRinse Glass Rapid
Power
Delay
Start
1/2 Load
3in1IntensiveNormal EcoRinse Glass Rapid
1. Please ensure the dishwasher is installed
by a qualified technician. Refer to the tools
required.
Power
Delay
Start
1/2 Load
3in1Intensive Normal Eco Rinse Glass Rapid
Location
When selecting a position for your slimline
dishwasher you should make sure the installation
surface is flat and firm, and the room is well
ventilated. Avoid locating your dishwasher near
a heat source, eg. cooker, boiler or radiator.
Extreme cold ambient temperatures may also
cause the appliance not to perform properly. This
dishwasher is not designed for use in a garage or
outdoor installation.
Do not drape the dishwasher with any covering.
When installing, ensure that free space is left at
the sides.
2. Ensure there is clearance each side of the
unit to allow slight sideways movement for
servicing when required. Good levelling is
essential for correct closure and sealing of the
door. When the unit is correctly levelled, the
door should not catch the inner liner on either
side of the cabinet. The adjustable feet may
be loosened or tightened in order to obtain
the optimum levelling of the unit.
Installation
All parts removed must be saved to
do the reinstallation in the future.
Ensure the dishwasher is unplugged
and empty. We recommend that 2
people handle the dishwasher during
installation.
LDW45S11_IB_110331.indd 6 3/31/11 5:04 PM
7
INSTALLATION
4. The condensation strip must be fitted to
the underside of the worktop above your
dishwasher to protect it against any moisture.
Its purpose is to protect your worktop’s
underside from steam rising from the
dishwasher.
• Ensure the surface is clean prior to sticking
the condensation strip to the underside of
the worktop.
• Remove the backing paper from the
condensation strip.
3. If required, the worktop of the dishwasher can
be removed. The height without the worktop
is 820 mm, the minimum dimensions required
to accommodate the dishwasher within fitted
kitchen furniture units.
Do not connect the unit to the mains socket
before installation. Ensure you are not
installing the unit right in front of the mains
socket. This is to avoid potential damage to
the back of the unit.
• Stick the condensation strip to the
underside of the worktop.
5. The worktop can be removed by removing
the fixing screws located at the rear of the
dishwasher. After removing the screws, lift
and push the worktop forward to release the
lugs from the front section of the dishwasher.
The polystyrene block and the lugs should be
saved for future use.
Power
Delay
Start
1/2 Load
3in1IntensiveNormal Eco RinseGlass Rapid
Stick the Condensation Strip
under the worktop, where you
want to install the dishwasher.
Leave some space
Remove
Remove
Remove
Unscrew
Failure to attach the condensation strip
could result in damage to the underside
of your worktop!
LDW45S11_IB_110331.indd 7 3/31/11 5:04 PM
8
INSTALLATION
7. Make sure your plumbing is suitable for use
with the dishwasher. If in doubt contact
a qualified plumber. This unit MUST BE
connected to COLD WATER MAINS using the
new water inlet hose. OLD HOSE SETS MUST
NOT BE RE-USED. The water pressure from
the water mains needs to be at a minimum of
0.04 MPa and a maximum of 1.00MPa.
• Connect one end of the safety water
supply hose to your dishwasher, and then
connect the other end of the hose to
your water mains. Please ensure the black
rubber seal is in place.
• After connecting the hose, turn on your
water mains and check for leaks.
• Connect the dishwasher to the mains
socket.
• Do not bend your drain hose.
6. Position the dishwasher next to a water tap
and a drain. Ensure the water inlet and drain
hoses are not kinked or squashed. The unit
must not stand on the mains cable.
water mains
safety water supply hose
Y-Adaptor
(not included)
Connect to
another
appliance
if required.
Power
Delay
Start
1/2 Load
3in1IntensiveNormal Eco RinseGlass Rapid
You may use a Y-adaptor (not included)
for an additional water feed for another
appliance, for example a washing
machine. This is only applicable for cold
water mains. A Y-adaptor is available
from most DIY stores.
LDW45S11_IB_110331.indd 8 3/31/11 5:04 PM
9
INSTALLATION
water drain hose
U-shaped drain hose
holder
• You may use the U-shaped drain hose
holder to secure your drain hose and to
avoid bending it.
• Secure the water drain hose to the waste
pipe to avoid it coming off during the
washing process.
The waste pipe must only be connected
to the foul drains and not the surface
water drainage system.
The water drain hose should be placed
between 40 cm and 100 cm from the floor
level and must not be extended, otherwise
the unit may not be able to expel the
waste water properly.
LDW45S11_IB_110331.indd 9 3/31/11 5:04 PM
10
Product Overview
Front View
Rear View
1. Control Panel
2. Door Handle
Power
Delay
Start
1/2 Load
3in1 Intensive Normal Eco Rinse Glass Rapid
2
3
1
5
4
3. Drain Hose
4. Water Inlet
(Connect To Supply Hose)
5. Mains Cable
(Connect To Electrical Mains Outlet)
LDW45S11_IB_110331.indd 10 3/31/11 5:04 PM
11
Upper Basket
Internal View
Lower Basket
6
10
11
12
13 14 15 16
7
8
9
6. Upper Basket
7. Salt Reservoir
8. Lower Basket
9. Detergent Dispenser
10. Cup Rack
11. Spray Arm
12. Filter
13. Rinse Aid Reservoir
14. Filtering System
15. Spray Arm
16. Salt Reservoir
LDW45S11_IB_110331.indd 11 3/31/11 5:04 PM
12
1. ON / OFF Button
• To turn the dishwasher on and off.
2. Power On Light
• Illuminates when On/Off button is pressed.
3. Display Window (Control Panel)
• Programme remaining time, delay time and
fault codes etc.
4. Delay Start Button
• Press to preset the wash timer and delay the
starting time by up to 24 hours.
• Each press of this button increases the delay
start time by 1 hour intervals.
5. Half Load Washing Button
• Press this button to select the half load
washing cycle.
Power
Delay
Start
1/2 Load
3in1 Intensive Normal Eco Rinse Glass Rapid
Control Panel
2 6 8
31 4 5 7
6. Half Load Indicator Light
• Illuminates when the half load washing cycle
is selected.
• Only the upper spray arms will be in
function.
• Load the soiled dishes in the upper basket.
7. Programme Button
• Press to select your required washing
programme.
8. Programme Indicator Light
• Illuminates when the programm is selected.
LDW45S11_IB_110331.indd 12 3/31/11 5:04 PM
13
Wash Cycle Table
Programme
Cycle Selection
Information
Process
Detergent
Amount
(Pre-wash/
Main wash)
Running
Time
(min.)
Energy
Consumption
(Kwh)
Water
Consumption
(I)
Rinse
Aid
3 In 1 • Pots, utensils
and cutlery.
• Highly soiled.
• Pre-wash
(50°C)
• Wash (50°C)
• Rinse (70°C)
• Drying
• 3 in 1 155 1.0 13
Intensive • Pots, pans,
casserole
dishes. Dishes
that have been
sitting with
dried food
on them for a
while.
• Pre-wash
(50°C)
• Wash (65°C)
• Rinse (55°C)
• Drying
• Pre-wash
(4g)
• Main
wash
(20g)
120 1.2 18
Normal • Pots, plates,
glasses and
lightly soiled
pans.
• Normally soiled.
• Pre-wash
(50°C)
• Wash (50°C)
• Rinse (65°C)
• Drying
• Pre-wash
(4g)
• Main
wash
(20g)
150 0.95 13
Eco*
(EN50242)
• Plates, glasses,
bowls.
• Lightly soiled.
• Pre-wash
• Wash (53°C)
• Rinse (65°C)
• Drying
• Main
wash
(20g)
160 0.81 12
Rinse • For dishes
that need to
be rinsed and
dried only.
• Wash (40°C)
• Rinse (70°C)
• Drying
• N/A 80 0.65 7
Glass • Glasses, crystal
and fine china.
• A shorter wash
for lightly soiled
loads.
• Pre-wash
• Wash (40°C)
• Rinse (60°C)
• Drying
• Main
wash
(15g)
95 0.65 13
Rapid • A shorter wash
for lightly
soiled loads
that do not
need drying.
• Wash (40°C)
• Rinse (45°C)
• Main
wash
(15g)
30 0.45 10
* To comply with Standards of Performance, i.e. EN50242, please ensure to use economy washing cycle for
the test.
Condensing dry technology
• Energy is saved by drying the dishes using the remaining heat after the last rinse cycle.
• Wash cycle times are extended due to this drying method.
• Some wash programmes do not have a drying function, please refer to the Wash Cycle Table
for more details.
LDW45S11_IB_110331.indd 13 3/31/11 5:04 PM
14
●
●
Small plastic items
(Milk bottle nipple)
Plastic items that
are not dishwasher safe
Crystal glasses
Silverware
Valuable vases
Copper pots and pans
Cast iron pans
Cracked / Chipped china
Scratched non-stick cookware
Towels and sponges
The Following Items Are Not Suitable
Before Operating
To Open the Door
• Pull the door handle.
• If the door is opened during operation all functions are automatically interrupted.
To Close the Door
• After loading the dishes, push the baskets fully into the dishwasher.
• Lift the door upwards and push until it clicks into position.
• Do not slam the dishwasher door.
Items Not Suitable for Use in the Dishwasher
When purchasing new crockery and cutlery, please make sure they are dishwasher-proof. Some items are
not suitable for dishwashers.
• Wooden cutlery and crockery or items with wooden parts may discolour and fade. The glue used in
these items is not dishwasher-proof and wooden handles may come loose after being washed in a
dishwasher.
• Craft items, antiques, valuable vases and decorative glassware are also not suitable for dishwashers.
• Plastic items (e.g. tupperware) which are not heat resistant may melt or loose shape due to the high
temperature in the dishwasher.
• Copper, brass, tin and aluminium items may discolour or become matt.
• Clouding may occur on glasses and delicate glassware after frequent washing. Do not wash delicate
glassware, or glassware containing lead crystal in a dishwasher. Wash delicate glassware by hand
instead.
• Silver and aluminium parts have a tendency to discolour during washing. Residues like egg white, egg
yolk and mustard often cause discolouring and staining on silver. Therefore, please clean the residues
from silver immediately after use.
LDW45S11_IB_110331.indd 14 3/31/11 5:04 PM
15
You can choose to add a detergent tablet
alone or to add detergent powder to both
the main wash detergent chamber and
the pre-wash detergent chamber for your
selected wash cycle. All programmes with
pre-wash need an additional detergent
dosage that must be placed in the
pre-wash detergent chamber (please refer
to the wash cycle table). This detergent
will take effect during the pre-wash phase.
Please follow the steps below to fill the detergent dispenser.
1. Push the button on the lid of the detergent
dispenser in the direction of the arrow until the
flap springs open.
Adding Detergent or Detergent Tablet
Only use detergents specifically designed for use in dishwashers. To be more environmentally friendly,
please use no more than the correct amount of detergent.
2. Fill the detergent dispenser with detergent
powder or insert the detergent tablet. The
marking indicates the filling level.
Bleach and
Countertop detergent
Irritant
3. Close the lid firmly so that it clicks into place.
• Keep out of the reach of children
• Irritating to eyes.
• Avoid contact with eyes. In case of contact with eyes, rinse
immediately with plenty of water and seek medical advice.
• If swallowed, seek medical advice immediately.
push up from the right side
pre-wash detergent chamber
main wash detergent chamber
or
LDW45S11_IB_110331.indd 15 3/31/11 5:04 PM
16
Alternatively, you can judge the amount of rinse aid by checking the rinse aid indicator right next to the
reservoir’s cap. When the indicator is black, it means it is full. When it is clear, it means it is almost empty.
Adjusting the Rinse Aid Reservoir
The rinse aid reservoir has six settings. Both the recommended
setting and the factory setting is “4.” If the dishes are not drying
properly or are spotted, adjust the dial to the next higher number
until your dishes are spot-free.
Rinse aid warning light will illuminate when the reservoir is
running out of rinse aid and requires refilling.
Adding Rinse Aid
Rinse aid helps to ensure water does not cling and leave marks on crockery during the drying phase and
helps crockery dry faster after it has been washed. Only pour rinse aid that is for domestic dishwashers into
the reservoir. This model is designed to use liquid rinse aids only.
Please follow the steps below to pour the rinse aid into the storage reservoir, and the amount will dispense
automatically.
1. Turn the cap and open as indicated.
2. When the cap open marking is aligned, you
may lift the cap up.
3. Pour the rinse aid in until the level indicator
turns completely black in colour and close the
cap.
4. Be careful not to overfill the reservoir. Wipe
up any spills. The approximate volume of the
rinse aid reservoir is 110ml.
rinse aid warning light
open
rinse aid indicator
If the water hardness in your area is soft, you
may not need rinse aid as it may cause white film
to develop on your dishes.
LDW45S11_IB_110331.indd 16 3/31/11 5:04 PM
17
Adding Salt
If the water in your area is hard, deposits will form on your dishes and
utensils. This appliance contains a salt reservoir for you to reduce the
hardness of the water.
Please follow the steps below to pour the salt into the salt reservoir and
it must be set to correspond to the water hardness level in your area.
1. Remove the lower basket and unscrew the reservoir cap.
2. Fill the reservoir with approximately 500ml of water (first use only).
3. Place the funnel provided over the salt reservoir.
4. Pour in approximately 1.2kg of dishwasher salt depending on the
brand used.
5. Clean any excess salt from around the reservoir opening and then
screw the cap on again firmly.
6. Run the “rapid” wash programme immediately (without any
crockery in the dishwasher) to remove any traces of salt from the
compartment.
The salt warning light will illuminate when the reservoir is
running out of salt and requires re-filling.
The salt warning light will cease to illuminate within a few
days depending on how quickly the salt dissolves.
OPEN
open
open
open
salt warning light
LDW45S11_IB_110331.indd 17 3/31/11 5:04 PM
18
Adjusting Salt Consumption
Salt consumption must be adjusted to correspond to the water hardness level in your area. If you don’t
know how hard the water in your home is, please ask the company that supplies water in your area.
It is recommended that adjustments should be made in accordance with the following chart.
Water Hardness
Selector
Position
Salt Consumption
(gram/cycle)
Number of cycle
/ 1.2 kgs
˚dh ˚fh ˚Clark mmol/l
0-8 0-14 0-10 0-1.4 / 0 /
8-22 14-39 10-28 1.4-3.9 - 20 60
22-45 39-80 28-56 3.9-8 Mid 40 30
>45 >80 >56 >8 + 60 20
turn
To optimise and customise the level of salt consumption, please follow the steps below to adjust the salt
consumption.
1. Remove the lower basket and unscrew the reservoir cap.
2. There is an arrow-shaped indicator in the reservoir, which you can turn. You may turn it to the “-” or “+”
settings based on the water hardness in your area.
1 ˚dh (German degree) = 1.25mmol/l
1 ˚fh (French degree) = 0.178mmol/l
1 ˚Clark (British degree) = 1.78mmol/l
• Do not use everyday table salt or cooking salt as they contain insoluble substances
which could damage the dishwasher.
• Do not pour detergent into the salt container. This will damage the dishwasher.
LDW45S11_IB_110331.indd 18 3/31/11 5:04 PM
19
Loading the Dishwasher
Before Loading the Dishwasher
Please observe the following notes before loading your cutlery and crockery into the basket.
• Remove lipstick stains and any food residues from crockery and dishes. Rinse if necessary.
• Dishes and cutlery must not lay inside one another, or cover each other.
• Load your cutlery and crockery so that water can access all surfaces.
• Ensure all items are securely positioned.
• Hollow items such as cups, glasses, pans, etc. must be placed upside down in the basket.
• Wide based items should be placed at an angle so that water can run off them freely.
• The spray arms must not be blocked by items which are too tall or hang through the baskets. If in
doubt, test for free movement by manually rotating the spray arms.
• Ensure that small items cannot fall through the holders in the baskets.
Do not wash items soiled with ash, sand, wax, lubricating grease or paint in the dishwasher. Ash
does not dissolve and can distribute in the dishwasher. Wax, sand, lubricating grease and paint
can cause damage to the dishwasher.
LDW45S11_IB_110331.indd 19 3/31/11 5:04 PM
20
Long items such as soup ladles, mixing spoons and long
knives should be placed lying down across the front of the
upper basket.
Upper Basket
Please use the upper basket for small and lightweight items
such as cups, saucers, glasses, dessert bowls, etc. Shallow
pans or casserole dishes can also be placed in the upper
basket.
remove the stop
lift
slide the basket
out from the rail
Adjusting the Upper Basket
More space can be created for large items on the upper or lower baskets by adjusting the height of the
upper basket.
Ensure that the rail stop is placed back properly after the height adjustment.
Loading the Upper Basket for 9 Place Settings
For loading the upper basket, please refer to the table below.
Number Item
1 Cups
2 Saucers
3 Glasses
4 Large serving bowl
5 Medium serving bowl
9 Dessert dishes
1
1
2
3
3
4
5
9
IN
For safety reasons, do not operate the dishwasher without the upper and lower baskets in place.
LDW45S11_IB_110331.indd 20 3/31/11 5:04 PM
21
Lower Basket
We recommend that large and the most difficult to clean items are
placed in the lower basket, such as plates, serving platters, saucepans,
serving bowls, pots, pans, lids etc. We recommend placing serving dishes
and lids at the side of the basket to avoid blocking the rotation of the
spray arms.
Hinged Cup Rack
To make room for taller items in the upper basket, raise the cup rack upwards. You can then lean the tall
glasses against it. You can also remove it when it is not required for use.
Hinged Spikes
The spikes are used for holding plates and a platter. They can be lowered to make more room for large
items. Please refer below for the steps to lower the spikes.
To prevent water dripping from the upper basket onto the dishes in the lower basket,
we recommend that you empty the lower basket first and then the upper basket.
Raise upwards
Raise upwardsRaise upwards
raise upwards
fold backwards
raise upwards
fold backwards
LDW45S11_IB_110331.indd 21 3/31/11 5:04 PM
22
Loading the Lower Basket
For loading the lower basket, please refer to the table below.
Number Item
6 Oval platter
7 Dinner plates
8 Soup plates
9 Dessert dishes
10 Cutlery basket
Cutlery Basket
Loading the Cutlery Basket
To make unloading much easier, cutlery should be grouped
in zones and placed in the cutlery basket. Please refer to the
table below for placement method.
Number Item
1 Forks
2 Soup spoons
3 Dessert spoons
4 Teaspoons
5 Knives
6 Serving spoons
7 Serving forks
IN
4 5
2 5
2 5
5 2
5 4
5 2
2 5
4 5
2 4
5 2
4 4
7 2
2 3
4 4
3 3
1 1
1 1
1 1
3 3
3 4
6 3
3 1
3 1
6 1
9
9
2
6
7
8
10
8
7
8
IN
9
9
2
6
7
8
10
8
7
8
• Do not let any items extend through the
bottom of baskets.
• To avoid the risk of injury, please load your
knives and forks with handles upwards. Do not
hold them by their sharp edges.
• The cutlery basket comes with covers, and
they are designed for you to load the cutlery
into the appropriate slots. If you use the basket
without the cover, it may reduce the washing
results of your cutlery.
• Please ensure the cover is securely locked to
the basket before operation.
• To comply with Standards of Performance, i.e.
EN50242, all cutlery must be loaded according
to the instructions in this manual.
LDW45S11_IB_110331.indd 22 3/31/11 5:04 PM
23
Starting a Wash Cycle
Please follow the steps below to start a wash cycle.
1. Ensure the unit is connected to the mains power and the water supply is on (water pressure between
0.04MPa and 1.00MPa).
2. Open the door. Pull out the lower and upper baskets, load the dishes and push the baskets back. It is
recommended that the lower basket is loaded first, and then the upper basket.
3. Pour in the detergent or place the detergent tablet in the detergent compartment and close firmly
afterwards.
4. Press the ON/OFF button, and the ON/OFF indicator light will illuminate.
5. Select the wash cycle programme based on the loading and soil requirements. Please refer to the
“Wash Cycle Table” (page 13).
6. The indicator light of the selected programme will illuminate.
7. Close the dishwasher door. A click sound should be heard when the door is closed correctly. Do not
slam the door.
8. The washing cycle will begin shortly.
Changing a Programme
To change the programme if the washing cycle has already started, follow the steps below.
1. Open the door slightly to check if the unit has dispensed the detergent or detergent tablet. This will
depend on how long the washing cycle was running for.
2. If the detergent dispenser lid is opened, we suggest that you allow the wash cycle to finish.
3. If the detergent dispenser lid is still closed, press and hold down the programme button for 3 seconds
to cancel the programme. You can then press the required new programme button and close the
dishwasher door. The unit will start the new washing cycle shortly.
OR
Press the required new programme button for more than 3 seconds to change the running
programme. The unit will start the new washing cycle shortly.
4. The display window shows the state of the dishwasher.
a. “--:--” means the unit is on stand by mode.
b. “H:MM” and not flashing means the unit is on pause.
c. “H:MM” and flashing means the unit is running.
At the End of a Programme
At the end of a programme, the dishwasher will make an audible sound.
If you open the dishwasher door during the washing cycle and then close it, the dishwasher will
continue the current washing programme after 10 seconds. However, if the door is not closed
correctly after 1 minute, the dishwasher will make an audible sound at 1 minute intervals.
The condensation strip helps to prevent the risk of steam damage to the worktop edging
above the dishwasher, it is advisable to leave the door closed until you are ready to unload the
crockery. However, you can also open the dishwasher door fully and wait until the dishes and
crockery are cool enough to unload. Do not leave the door only partially open.
LDW45S11_IB_110331.indd 23 3/31/11 5:04 PM
24
Switching O the Unit
To save energy, remember to switch the dishwasher off using the ON/OFF button. The dishwasher will
continue to use electricity until it is switched off with the ON/OFF button.
If the dishwasher is not going to be used for a long period of time, e.g. whilst on holiday, disconnect the
unit from the mains supply.
Unloading the Dishwasher
Allowing dishes to cool down before unloading is important as dishes tend to break and chip more easily
when they are hot. Therefore, if you open the dishwasher door fully after switching off, it will allow the
dishes to cool down much faster.
We suggest:
Unload the lower basket first, followed by the cutlery basket and then the upper basket.
This will prevent water drops from the upper basket from falling onto the dishes in the lower basket.
Delay Start
The starting time of a washing programme can be delayed and adjusted. Please follow the steps below.
1. Open the dishwasher door and load your soiled dishes and crockery.
2. Press the ON/OFF button to turn on the dishwasher.
3. Select your preferred programme.
4. Press the Delay / Start button.
5. Set the required delay start time using the Delay / Start button.
6. Close the door and the unit will start the programme at the assigned time automatically.
Half Load
In case you do not have enough dishes for a full load, the half load option can be selected for washing with
upper spray only. Only load the dishes into the upper basket. This will save hot water and electricity usage.
Please follow the steps below.
1. Open the dishwasher door and load your soiled dishes and crockery onto the upper basket.
2. Press the ON/OFF button to turn on the dishwasher.
3. Select your preferred programme.
4. Press the 1/2 button.
5. Close the door and the unit will start the programme with upper spray only.
Each press of this button increases the delay start time by 1 hour increments.
LDW45S11_IB_110331.indd 24 3/31/11 5:04 PM
25
Internal Care
Filtering System
The filtering system in the base of the wash cabinet captures large particles of suds solution. Build up of
these particles may cause the filters to block. Check the condition of the filters regularly and clean them if
necessary under running water.
Follow the steps below to clean the filters in the wash cabinet.
1. Ensure the dishwasher is switched off.
2. Unscrew the coarse filter, and gently lift it out.
3. Carefully lift the main filter out.
4. Carefully lift the fine filter out.
5. Rinse all the filters under running water, then refit all filters in the following order.
6. Carefully refit the fine filter with filter.
7. Carefully refit the main filter.
8. Gently screw in the course filter in a clockwise direction.
Cleaning After Use
External Care
The Door and the Door Seal
1. Clean the door seals regularly with a soft damp cloth to remove food deposits.
2. When the dishwasher is being loaded, food and drink residues may drip onto the sides of the
dishwasher door. These surfaces are outside the wash cabinet and are not accessed by water from the
spray arms. Any deposits should be wiped off before the door is closed.
The Control Panel
If cleaning is required, the control panel should be wiped with a soft damp cloth ONLY.
Filter cylinder
without the lters
• To avoid penetration of water into the door lock and electrical components, do not use a
spray cleaner of any kind.
• Never use abrasive cleaners or scouring pads on the outer surfaces because they may scratch
the finish. Some paper towels may also scratch or leave marks on the surface.
• Do not over tighten the filters. Put the filters back in the filter cylinder in sequence securely,
otherwise the residue could get into the system and cause a blockage.
• NEVER use the dishwasher without the filters in place. Improper replacement of the filters
may reduce the performance level of the appliance and damage dishes and utensils.
LDW45S11_IB_110331.indd 25 3/31/11 5:04 PM
26
Spray Arms
Particles of food can get stuck in the spray arm jets and
bearings. The spray arms should therefore be checked and
cleaned regularly.
• Use a pointed object, eg. a cocktail stick, to loosen food
particles in the spray arms’ jets.
Frost Precaution
Avoid placing the dishwasher in a location where the temperature is below 0°C. If your appliance is left in
an unheated place over the winter, you are advised to:
1. Disconnect the unit from the water inlet.
2. Turn on the unit. Select any washing cycle and let it run for 1 minute only. This will allow all the
excessive water that remains in the unit to drain out.
3. Disconnect from the mains.
4. Empty the dishwasher.
5. Close the dishwasher’s door.
6. Disconnect the unit from the water drain. Use a suitable receptacle to catch the water.
Should you encounter any difficulties with the above steps, please ask a service technician for assistance.
Moving the Dishwasher
If you have to move the unit, for instance due to moving house, you are advised to:
1. Disconnect the dishwasher from the mains.
2. Disconnect the unit from the water inlet and drain. Use a suitable receptacle to catch the water.
3. Remove the unit from the current location with the hoses discharged.
4. Pull the unit out together with the hoses.
Maintenance After a Prolonged Period of
Non-Operation
If you are not going to use the unit for a prolonged period of time, you are advised to:
1. Disconnect the dishwasher from the mains.
2. Disconnect the unit from the water inlet and drain. Use a suitable receptacle to catch the water.
3. Open the door slightly to prevent unpleasant smells building up in the compartment.
4. Ensure the washing compartment of the dishwasher is clean.
Do not attempt to remove the spray arms.
• Avoid over tilting the unit during transportation.
• We recommend that 2 people handle the dishwasher during installation.
LDW45S11_IB_110331.indd 26 3/31/11 5:04 PM
27
Hints and Tips
Fault Code
Codes Possible Causes Remedy
E1
Water tap is not turned on. Turn on the water tap.
Low water pressure (<0.04MPa) Turn on the water tap and ensure it is in full
position.
Flow meter is broken.
• Disconnect from the mains.
• Disconnect the water inlet.
• Call a qualified technician.
The wire terminals which connect the
flow meter are loose.
E4
The tank is leaking.
The hose is leaking.
The float switch is broken or PCB is
faulty.
Technical Problems
Technical Problems
Problem Possible Causes Remedy
The dishwasher does not start.
The door is not properly
closed.
Close the door firmly.
The unit is not connected to
the mains.
Connect the plug to the mains.
The unit is not switched on. Press the “on” button and select a
programme.
The drain pump is not working
properly.
Fault code E4 - The antiflooding system has operated.
• Disconnect from the mains.
• Disconnect the water inlet.
• Call a qualified technician.
Repairs should only be carried out by a qualified technician in strict accordance with current
local and national safety regulations. Unauthorised or incorrect repairs could cause personal
injury or damage to the unit.
LDW45S11_IB_110331.indd 27 3/31/11 5:04 PM
28
General Problems
Problem Possible Causes Remedy
Detergent residue is left in the
dispenser at the end of the
programme.
The detergent dispenser was
still damp when detergent was
added.
Make sure the dispenser is dry before
adding detergent.
The detergent dispenser lid
cannot be closed properly.
Clogged detergent residue is
blocking the catch.
Clean the catch.
Knocking noise in the wash
cabinet.
A spray arm is knocking
against an item in a basket.
Interrupt the programme, and
rearrange the items which are
obstructing the spray arm. See the
section “loading the dishwasher”.
Smearing appears on
glassware and cutlery.
The rinse aid dosage is set too
high.
Adjust the dial of the rinse aid
dispenser to a lower setting.
Dishes, cutlery and glasses are
not dry.
The amount of rinse aid may
be insufficient, or the rinse aid
reservoir is almost empty.
Replenish the reservoir, adjust the
rinse aid dispenser dial to a higher
setting or change the brand of rinse
aid.
Crockery was taken out of the
dishwasher too soon.
Leave the crockery in the dishwasher
until you hear an audible sound.
White residue is visible on
cutlery and crockery, clouding
occurs on glassware; film can
be wiped off.
Not enough rinse aid was
used.
Replenish the reservoir, adjust the
rinse aid dispenser dial to a higher
setting or change the brand of rinse
aid.
There is not enough salt in the
salt reservoir.
Fill the salt reservoir.
The salt reservoir cap has not
been screwed on correctly.
Ensure that it is screwed back on
correctly.
Unsuitable detergent has been
used.
Change your detergent. Use a
dishwasher standard powder
detergent.
The salt consumption setting
is too low.
Select a higher salt consumption
setting.
Glassware is dull and
discoloured; film cannot be
wiped off.
The glassware is not
dishwasher proof. The surfaces
are affected.
Wash the non-dishwasher proof
glassware by hand.
Tea or lipstick stains have not
been completely removed.
The wash temperature of the
selected programme was too
low.
Select a programme with a higher
wash temperature.
The bleaching effect of the
detergent used is too low.
Change your detergent.
Forgot to pre-rinse or remove
the stains with a napkin prior
to washing.
Pre-rinse or remove the stains with a
napkin prior to washing.
LDW45S11_IB_110331.indd 28 3/31/11 5:04 PM
29
Disposal of the Dishwasher
• When disposing your old dishwasher, first make it unusable. Disconnect the hoses and unplug the
mains cable. Cut off the mains cable from the dishwasher. Make the door lock inoperative, so that
children cannot accidentally shut themselves in. Make appropriate arrangements for the disposal of the
dishwasher.
• At the end of its working life, the product must not be disposed of as urban waste. It must be taken
to a special local authority differentiated waste collection centre or to a dealer providing this service.
Disposing of a household appliance separately avoids possible negative consequences for the
environment and health deriving from inappropriate disposal and enables the constituent materials
to be recovered to obtain significant savings in energy and resources. As a reminder of the need to
dispose of household appliances separately the product is marked with a crossed out wheeled dustbin.
• Please ensure that it presents no danger to children while being stored for disposal.
Disposal of Packing Material
Please dispose of the plastic wrappings and bags safely and keep out of the reach of babies and young
children.
LDW45S11_IB_110331.indd 29 3/31/11 5:04 PM
30
Specications
Model LDW45S11
Dimensions 450 mm (W) x 580 mm (D) x 850 mm (H)
Capacity 9 Place Settings
Water Pressure Required 0.04 - 1.00MPa
Power Consumption 1930W
Rated Voltage 230V/50Hz
Features and specifications are subject to change without prior notice.
LDW45S11_IB_110331.indd 30 3/31/11 5:04 PM
31
Safety Warnings
For your continued safety and to reduce the risk of injury or electric shock, please follow all the safety
precautions listed below.
• Read all instructions carefully before using the dishwasher and keep them for future reference.
• Retain the manual. If you pass the dishwasher onto a third party, make sure to include this manual.
• Keep ventilation openings in the dishwasher enclosure clear of obstructions.
• Choose a location for your dishwasher away from heat sources such as radiators or fires.
• Young children should be supervised to ensure that they do not play with the dishwasher.
• Keep mains cable out of reach from children.
• This dishwasher is not intended for use by persons (including children) with reduced sensory or
mental capabilities, or lack of experience and knowledge unless they have been given supervision or
instructions concerning the use of the dishwasher by a person responsible for their safety.
• Keep children away from detergents and rinse aids. These may cause chemical burns in the mouth,
throat and eyes or asphyxiation.
• Keep children away from the dishwasher when the door is open.
• Switch off and unplug before fitting or removing tools/attachments, after use and before cleaning.
• Keep your fingers away from moving parts and fitted attachments.
• Never use a damaged machine.
• If the mains cable is damaged, it must be replaced by the manufacturer, its service agent or a qualified
technician in order to avoid a hazard.
• Keep the power unit, mains cable or plug away from water.
• Never exceed the maximum capacities.
• 2 people are required to lift this dishwasher.
• Only use the dishwasher for its intended domestic use.
WARNING
IT IS HAZARDOUS FOR ANYONE OTHER THAN AUTHORISED SERVICE PERSONNEL TO CARRY OUT
SERVICING OF REPAIRS WHICH INVOLVE THE REMOVAL OF COVERS.
TO AVOID THE RISK OF AN ELECTRICAL SHOCK DO NOT ATTEMPT REPAIRS YOURSELF.
• Do not sit or stand on the door or dish rack.
• Do not move your dishwasher by holding the door or its edges. Hold the dishwasher around its sides or
base when moving it.
• Do not touch the heating element during or immediately after use.
• Do not operate your dishwasher unless all enclosure panels are properly in place. Open the door
very carefully when there is a programme running as there is a risk of hot water spraying out of the
appliance.
• Do not place any heavy objects on the open door. The appliance could tip.
• When loading items to be washed:
1. Locate sharp items so that they will not damage the door seal;
2. Warning: Knives and other utensils with sharp points must be loaded in the basket with the points
downwards or placed horizontally.
• Do not allow plastic items to come into contact with heating element.
• Check that the detergent receptacle is empty after completion of the wash cycle.
• Do not wash plastic items unless they are marked dishwasher safe or equivalent.
• Use only detergent and rinse aids designed for an automatic dishwasher.
• Other means for disconnection from the supply must be incorporated in the fixed wiring with at least
3mm contact separation in all poles.
• The door should not be left in the open position since this could present a tripping hazard.
LDW45S11_IB_110331.indd 31 3/31/11 5:04 PM
32
• For energy saving, always remember to switch the dishwasher off when you have finished using it. The
dishwasher should not be left unattended when in use.
• Remove the door to the washing compartment when removing an old dishwasher from service or
discarding it.
• During installation, the power supply cord must not be excessively or dangerously bent or flattened.
• Do not tamper with controls.
• The appliance is to be connected to the water mains using new hose sets.
• The maximum number of place settings to be washed is 9.
• The maximum permissible inlet water pressure is 1Mpa, and the minimum permissible inlet water
pressure is 0.04Mpa.
Earthing Instructions
WARNING: THIS APPLIANCE MUST BE EARTHED.
• This appliance is equipped with a mains cable having an equipment-earthing conductor
and an earthing plug.
• The plug must be plugged into an appropriate outlet that is installed and earthed in
accordance with local standards and requirements.
• Improper connection of the equipment-earthing conductor could result in a risk of electric
shock.
• The wires in the cord are coloured as follows:
• Green and Yellow = Earth,
• Blue = Neutral,
• Brown = Live.
• Check with a qualified electrician or service representative if you are in doubt whether the
appliance is properly earthed or the plug does not fit correctly.
• Never modify the plug provided with the appliance.
LDW45S11_IB_110331.indd 32 3/31/11 5:04 PM
NOTE: If you require a replacement for any of the items listed below, please quote their corresponding
part numbers:
Replacement Part Part Number
Cutlery Basket 673002200080
Water Supply Hose 673000900060
Detergent Measuring Spoon 673002200079
Measuring Cup 673006200004
Condensation Strip 675001300715
Salt Funnel 673002200043
U-shape Hose Holder 673006200003
This symbol on the product or in the instructions means that your
electrical and electronic equipment should be disposed at the end
of its life separately from your household waste. There are separate
collection systems for recycling in the EU.
For more information, please contact the local authority or your
retailer where you purchased the product.
DSGRetailLtd.•MaylandsAvenue•HemelHempstead
Herts•HP27TG•England
(P.N.: LDW45S11-000)
Visit Partmaster.co.uk today for the easiest way to
buy electrical spares and accessories. With over
1 million spares and accessories available we can
deliver direct to your door the very next day. Visit www.partmaster.co.uk or call
0844 800 3456 (UK customers only) Calls charged at National Rate.
LDW45S11_IB_110331.indd 33 3/31/11 5:04 PM
LDW45S11_IB_110331.indd 34 3/31/11 5:04 PM
LDW45S11_IB_110331.indd 35 3/31/11 5:04 PM
LDW45S11_IB_110331.indd 36 3/31/11 5:04 PM
Loading...