Logik L32HED13, L32HE13 Quick Start Manual

Connecting the Aerial

Connect one end of the RF coaxial cable to the aerial socket on the wall
and the other end of the cable to the AERIAL IN socket at the rear right
bottom view of your TV.

Connecting to the Mains Socket

1. Connect the mains cable to the mains socket after you have
completed all the connections.

2. In standby mode, press the button on the remote control to
turn the TV on. The red LED indicator will turn blue.

Installing the Base StandUnpacking

Remove all packaging from the TV. Retain the packaging.
If you dispose of it please do so according to local regulations.

TV

TV Stand

Remote Control/AAA Batteries x 2

Screw x 5

Component Adapter Cable (YPbPr)

Composite Adapter Cable (AV)

Instruction Manual

Operating Your Remote Control

1. Press and lift the back cover to
open the battery compartment
of the remote control.

2. Inser t two AAA size batteries.
Make sure to match the (+) and
( - ) ends of the batteries with
the (+) and ( - ) ends indicated
in the battery compartment.

3. Close the battery compar tment
cove r.

1. Disconnect all cables connected to the TV.

2. Lay the TV down on a flat surface ideally on the edge of a table so the

base of the TV slightly overhangs the edge of the table, with the back
side facing up. Please make sure a soft cushioned material (such as
a dry bath towel or thick piece of foam) is placed beneath the screen.

3. To install the TV stand, place
the stand into the stand
recess on the back of
the TV.

PC-RGB In

PC

Audio In

SCART RF InHDMI 1 In HDMI 2 In

To the mains socket

Well done, your new TV is now ready to use. You will find that there are many exciting features available. To get to know all these features,

please take some time to read the instruction manual provided with your TV.

If after reading the instruction manual you have additional questions related to the use of your TV please call our UK Call Centre on 0844 561 1234.
Our UK Customer Contact Centre is open Monday-Saturday 8am-8pm or Sunday 8am-6pm.

QSG-L32HE13_HED13-130411V2

Turning On and Tuning In the TV

1. The first time you turn the TV on, it will go
straight into the First Time Installation menu.

Please ensure the aerial is plugged in and

then press the OK button.

2. Press the buttons to select your
desired language to be displayed on the
menu. The default on-screen menu language
is set as English. Press the OK button to
confirm.

3. To select the country option press the
buttons. Press the OK button

to confirm.

4. Channel tuning will commence. This operation
may take up to 10 minutes. The display will
show the progress of the tuning and the
number of channels found.

Please select an OSD Language

Deutsch

Español Français

Português Italiano

English

Please ensure aerial is plugged in!!

Then press OK button to start

Tune Type

Czech

Denamrk

France

Finland

Germany

Italy

Netherlands

UK

Menu

DTV

Hungary

Target Region Setting

Country Code GBR

Primary Region England

Secondary Region

Tertiary Region

London

Channel Tuning

TV : 0 Channel

DTV : 0 Channel

Radio : 0 Channel

Data : 0 Channel

1 %... 471.25 MHz (DTV)

Please press MENU key to skip

Target Region Setting

During tuning your TV may have received
signals from more than one transmitter. If this
has occurred the Target Region Setting screen
will be displayed. This will enable you to select
the correct regional transmission for the local
news service that you require.

1. Press the OK button to confirm the Country
Code, this will highlight the Primary Region
England.

2. Press the OK button to highlight Secondary
Region and press the buttons to select

your preferred option (if available).

3. Press the OK button to confirm, and Tertiary
Region will be highlighted. Press the

buttons to select the your preferred option
(if available).

4. Press the OK button to confirm. The main
menu will be briefly displayed.

Your TV is now fully tuned in.

Quick Start Guide

32” HD Ready LED TV

L32HE13
L32HED13

(with DVD Player)

Table

Cushioned
material

screw in

Screws x 5

4. Secure the stand using the 5 screws provided.

L32HED13_QSG.indd 1 11/04/2013 17:45