How it Works
Logik
Loading...
L19DIGB11
Instruction Manual
56 pgs17.1 Mb0

Logik L19DIGB11 Instruction Manual

19” HD Ready Digital LCD TV
Instruction Manual L19DIGB11
L19DIGB11_IB_110315_Annie.indd 1 11年3月15日 上午11:32
L19DIGB11_IB_110315_Annie.indd 2 11年3月15日 上午11:32
Contents
Preparation .........................................................................................................................................................................................5
Front View and Controls ...................................................................................................................................................................................................7
Remote Control Operation Range ................................................................................................................................................................................9
Connections ......................................................................................................................................................................................13
Connecting an AV Device with a Component (YPbPr) Cable ...........................................................................................................................14
Initial Setup ......................................................................................................................................................................................17
Turning the TV on for the First Time ..........................................................................................................................................................................17
− Selecting the Input Source................................................................................................................................................................................18
− Channel Selection ...............................................................................................................................................................................................18
− Display Channel Information ...........................................................................................................................................................................18
− Volume Adjustment .............................................................................................................................................................................................18
Using the Features ...........................................................................................................................................................................19
Customising the Channel Setting (TV, DTV or Radio Mode) .............................................................................................................................19
− Auto Tuning ............................................................................................................................................................................................................19
− DTV Manual Tuning.............................................................................................................................................................................................20
− ATV Manual Tuning ............................................................................................................................................................................................. 20
− Channel Edit (ATV / DTV Mode) .......................................................................................................................................................................21
− Signal Information (DTV Mode) ...................................................................................................................................................................... 22
− CI (Common Interface) (DTV Mode) .............................................................................................................................................................. 23
− Software Update (Over Air Download)........................................................................................................................................................ 24
− Software Update (USB) ...................................................................................................................................................................................... 24
− Stereo / Dual Sound Reception (ATV Mode) .............................................................................................................................................. 28
− Speaker Sound Output Selection (DTV Mode) ......................................................................................................................................... 28
− OSD Language ......................................................................................................................................................................................................29
− Audio Language (DTV Mode) .......................................................................................................................................................................... 30
− Subtitle Language (DTV Mode) .......................................................................................................................................................................31
− Hearing Impaired ..................................................................................................................................................................................................31
− Country .....................................................................................................................................................................................................................31
− PVR File System (DTV Mode) ............................................................................................................................................................................32
− CEC (Consumer Electronics Control) ............................................................................................................................................................ 33
− Restore Factory Default ..................................................................................................................................................................................... 33
Customising the LOCK Setting .................................................................................................................................................................................... 34
− Lock System ...........................................................................................................................................................................................................34
− Set Password ......................................................................................................................................................................................................... 35
− Block Channel ....................................................................................................................................................................................................... 36
− Parental Guidance ............................................................................................................................................................................................... 37
L19DIGB11_IB_110315_Annie.indd 3 11年3月15日 上午11:32
− To Turn on Teletext Function........................................................................................................................................................................... 38
Digital Teletext (DTV Mode) ......................................................................................................................................................................................... 39
− Teletext within Digital Service ........................................................................................................................................................................ 39
− Switch On / O EPG ............................................................................................................................................................................................. 39
− Select a Programme ........................................................................................................................................................................................... 40
Using the Features via USB Port .....................................................................................................................................................41
My Photo ..............................................................................................................................................................................................................................41
My Music ..............................................................................................................................................................................................................................41
My Movie ............................................................................................................................................................................................................................. 42
PVR (Personal Video Recorder) .......................................................................................................................................................44
DVR (Digital Video Recorder) ..........................................................................................................................................................44
Play Recorded Programme .......................................................................................................................................................................................... 46
Maintenance .....................................................................................................................................................................................48
Hints and Tips ...................................................................................................................................................................................49
Display Modes ..................................................................................................................................................................................50
Specifications ...................................................................................................................................................................................51
Safety Warnings ...............................................................................................................................................................................52
L19DIGB11_IB_110315_Annie.indd 4 11年3月15日 上午11:32
GB
5
Preparation
Unpacking the TV
Remove all packaging from the TV. Retain the packaging. If you dispose of it please do so according to local regulations.
The following items are included:
Remote Control / AAA Batteries x 2
(P.N.: 504C2413102 & 32200007158)
Screw A
(P.N.: 209100412B1)
Instruction Manual
(P.N.: 4031C191322)
Quick Start Guide
(P.N.: 4033C191307)
Digital TV Switchcover Addendum
(P.N.: 4031C241307)
Thank you for purchasing your new Logik 19" HD Ready Digital LCD TV.
Your new TV has many features and incorporates the latest technology to enhance your viewing experience. We recommend that you spend some time reading this instruction manual in order that you fully understand these features. You will also find some hints and tips to help you resolve any issues.
Read all the safety instructions carefully before use and keep this instruction manual for future reference.
If items are missing, or damaged please contact Partmaster (UK only). Tel: 0844 800 3456 for assistance.
Preparation
TV
TV Base
(P.N.: 102C1912111)
L19DIGB11_IB_110315_Annie.indd 5 11年3月15日 上午11:32
GB
6
Preparation
4. To remove the base stand, untighten the 3 screws that hold the base stand to the rear of the TV. Slide the base stand out.
1. Disconnect all cables connected to the TV.
2. Lay the TV down on a flat surface with the back side
facing up. Please make sure to place a soft cushioned material (such as a pillow or thick piece of foam) beneath the screen.
3. To install the base stand, align the screw hole and then secure the base stand with provided the 1 screw.
5. Mounting on the wall. This TV is designed to be wall­mounted with a standard 100 mm x 100 mm mounting kit designed for flat-panel TVs (sold separately). Mount this TV according to the instructions included in the mounting kit. Due to space restrictions, we recommend that you make all connections (refer to page 13-16 for details) before mounting on to the wall.
screw
unscrew
Installing / Removing the Base Stand
Screws x 3
(P.N.: xxxxxxxxxxx)
100 mm
100 mm
Four mounting holes
(size M4x12 screw)
• Please read this instruction manual carefully while setting up your TV.
• If you require additional assistance please call our UK Call Centre on 0844 561 1234. Our UK Customer Contact Centre is open Monday-Saturday 8am-8pm or Sunday 8am-6pm.
Keep all the spare screws should you want
to use the base stand option.
• Remove the base stand before mounting the TV onto the wall.
• The LCD display is very fragile, and must be protected at all times when installing and removing the base stand. Be sure that no hard or sharp object, or anything that could scratch or damage the LCD display, comes into contact with
it. DO NOT exert pressure on the front of the TV at any time because the screen could crack.
Screw A x 1
(P.N.: 209100412B1)
Screw B x 3
(P.N.: 209060410B1)
L19DIGB11_IB_110315_Annie.indd 6 11年3月15日 上午11:32
GB
7
Preparation
Front View and Controls
Item Description
1 POWER LED
Illuminates green when the TV is turned on. Illuminates red when the TV is in standby mode. The LED will flash green and red when the timer programming has started in the standby mode.
2 IR (Infrared Receiver)
Receives IR signals from the remote control. Do not put anything near the sensor, as its function may be affected.
3 INPUT
Press to select among different input signal sources: DTV / ATV / SCART / YPbPr / PC / HDMI / AV / DMP. Confirmed the selection on OSD menu.
4 MENU Displays the OSD (on screen display) menu.
5 CH + / – Press to select a channel or select a sub-menu from the OSD menu.
6 VOL + / –
Adjusts the volume. Press to select and adjust a setting in the OSD menu.
7
Switches the TV on from standby mode. Switches the TV back to standby mode.
8 USB
Allows the insertion of a USB storage device to play video, audio, photo and text files (DMP mode) and record DTV programmes on to a USB storage device.
3
4
6
7
8
5
1 2
L19DIGB11_IB_110315_Annie.indd 7 11年3月15日 上午11:32
GB
8
Preparation
Rear View and Sockets
Socket Description
1 Mains Cable Connects the mains cable to the mains socket.
2 ANT Aerial To connect to the aerial socket on the wall with the RF coaxial cable.
3 VGA / PC AUDIO To connect to a computer or other devices with a VGA interface.
4 SCART To connect to a VCR, DVD Player, or other AV device with a SCART output socket.
5 COMMON INTERFACE Allows the insertion of a Common Access Module. (Refer to page 23 for details)
6 VIDEO / AUDIO (L/R)
To connect to the Composite VIDEO and AUDIO (L/R) output sockets on external video devices.
7 Y, PB, PR / AUDIO (L/R)
To connect to a DVD player, Digital Set-Top-Box, or other AV devices with component (YPbPr) video and audio output sockets.
8 HDMI
To connect to a High-Definition (HD) signal output device, such as a set-top box, blu-ray disc player or AV receiver.
1 2 5
6
7 8
3
100-2 40V~ 50 /60Hz
AC-IN PUT
VGA IN PUT
SCART
AUDIO INPUT
PC
R
L
YPbVIDEO
Pr
HDMI INPU T
ANT
4
L19DIGB11_IB_110315_Annie.indd 8 11年3月15日 上午11:32
GB
9
Preparation
Remote Control Operation Range
Point the remote control at the TV no more than 5 metres from the remote control sensor on the TV and within 60° in front of the TV. The operating distance may vary depending on the brightness of the room.
Installing Batteries in the Remote Control
1. Press and lift the back cover to open the battery compartment of the
remote control.
2. Insert two AAA size batteries. Make sure to match the (+) and ( - ) ends of the batteries with the (+) and ( - ) ends indicated in the battery compartment.
3. Close the battery compartment cover.
30° 30°
5M
Handling the Batteries
• Improper or incorrect use of batteries may cause corrosion or battery leakage, which could cause fire, personal injury or damage to property.
• Only use the battery type indicated in this manual.
• When the batteries are exhausted, the remote will not function. Replace both batteries at the same time with new ones.
• Do not install new batteries with used ones and do not mix different types of batteries.
• Do not dispose of used batteries as domestic waste. Dispose of them in accordance with local regulations.
Handling the Remote Control
• Take care of your fingernails when you press and hold the battery release tab.
• Do not drop or cause impact to the remote control.
• Do not spill water or any liquid on the remote control.
• Do not place the remote control on a wet object.
• Do not place the remote control under direct sunlight or near sources of excessive heat.
• Remove the battery from the remote control when not in use for a long period of time, as it could cause corrosion or battery leakage and may result in physical injury and/or property damage including fire
L19DIGB11_IB_110315_Annie.indd 9 11年3月15日 上午11:32
GB
10
Preparation
1.
Switches the TV between on and standby mode.
2.
MUTE
Mutes and restores your TV sound.
3. 0-9 Number Button
Press to select a programme. Select numbered items in a menu. (DVD mode)
4. LIST
Display channel list. (ATV / DTV mode)
5.
RECALL
Return to the previous viewing channel. (ATV / DTV mode) Return to menu (DVD mode)
6. SLEEP
Sets the TV sleep timer: OFF / 10 / 20 / … / 180 / 240 min.
7. VOL + / –
Adjusts the volume.
8. CH + / –
Select a channel.
9. PROG
Display the channel edit menu. (ATV / DTV mode) Programme the DVD. (DVD mode)
10. S.MODE
Select sound mode: Standard / Music / Movie / Sports / User.
11. ASPECT
Allows you to watch the screens in various formats: Auto / 4:3 / 16:9 / Zoom / Subtitle / Smart Zoom.
12. GUIDE
Displays the EPG electronic Programme guide. (DTV mode)
TITLE
Displays the DVD title content. (DVD mode)
13. P.MODE
Select picture mode: Standard / Mild / User / Dynamic.
14. MENU
Display the OSD (On Screen Display) menu.
15. INPUT
Select among the dierent input signal sources: DTV / ATV / SCART / YPbPr / PC / HDMI / AV / DMP
16.
Allows you to navigate the OSD menus and adjust the system settings to your preference.
OK
Conrm the selection in the OSD menus.
17. BACK
Return to the previous menu in the OSD menus.
18. Exit
Exit the OSD menu.
Remote Control
1
2
5
8
12
15
18
9
13
3
4
7
11
14
16
17
6
10
Please note that there are DVD mode functions on the remote control only operate on TV models with a built-in DVD player.
L19DIGB11_IB_110315_Annie.indd 10 11年3月15日 上午11:32
GB
11
Preparation
19. FAV
Display the favourite channel list. (ATV / DTV mode)
SETUP
Display and exit the DVD setup menu. (DVD mode)
20. i
Display the present screen information such as the current channel on ATV / DTV mode and the input source except ATV / DTV mode.
21. TV.RD
A short-cut to switch input source to TV / Digital radio channels.
Eject a disc. (DVD mode)
22. AD (Audio Description)
Switches between the audio languages (only applicable when the TV programme has this feature). (DTV mode) Select Stereo / Dual Sound Reception (ATV mode)
23. TEXT
Turns on and o the teletext function. (ATV / DTV mode)
MENU
Display the DVD menu. (DVD mode)
24. S (Subtitle)
Displays subtitles which are broadcast with the programme. (DTV mode). Displays subtitles on the DVD. (DVD mode)
25.
REC
Record the current programme. (DTV mode).
ZOOM
Zoom in on the displayed frame. (DVD mode)
26.
Allows you to navigate the DVD menu and adjust the system settings to your preference. (DVD mode)
OK
Conrm the selection in the DVD menus. (DVD mode)
CANCEL
To exit the teletext mode. (ATV mode)
MIX
Select TELETEXT with a TV programme. (ATV mode)
SIZE
To enlarge the picture on the TV in teletext. (ATV mode)
27.
Stop
To stop the playback or recording. (DVD / DMP mode)
28. ANGLE
Select dierent angles for the video. (DVD mode)
29.
Pause
To pause playback. (DVD / DMP mode) Start the time-shift function (DTV mode)
STEP
To play the playback forward frame by frame. (DVD mode).
30.
PLAY
To start playback. (DVD / DMP mode)
25
27 29
30
23
24
26
28
22
20
2119
Please note that there are DVD mode functions on the remote control only operate on TV models with a built-in DVD player.
L19DIGB11_IB_110315_Annie.indd 11 11年3月15日 上午11:32
GB
12
Preparation
31.
To skip to the beginning of the next chapter / track / photo.
REVEAL
Reveals hidden information such as the answer to a quiz in teletext. (ATV mode).
32.
To skip to the beginning of the previous chapter / track / photo.
HOLD
Freezes a multi-page passage on screen in teletext. (ATV mode)
33.
To reverse playback rapidly.
SUBPAGE
Displays the subpage on the teletext screen. (ATV mode)
34.
To advance playback rapidly.
INDEX
To select the page number of the index from teletext. (ATV mode)
35. Coloured buttons
Access the TELETEXT items or channel edit when using Digital / Freeview TV Channels. (ATV / DTV mode)
GOTO (RED)
To skip to a specic location on a DVD / CD. (DVD mode)
SLOW (GREEN)
Play video slow. (DVD mode)
REPEAT (YELLOW)
Select between dierent repeat modes. (DVD mode)
A–B (BLUE)
Repeat a segment between A and B. (DVD mode)
34
33
32
35
31
Please note that there are DVD mode functions on the remote control only operate on TV models with a built-in DVD player.
L19DIGB11_IB_110315_Annie.indd 12 11年3月15日 上午11:32
GB
13
Connections
Connecting an AV Device with an HDMI Cable
• This TV can accept High-Definition Multimedia Interface (HDMI) supports HDCP (High-Bandwidth Digital Content Protection) Protocol.
• When you connect to the output of an HD ready player (blu-ray disc player, game console, set-top box or computer) switch to the HDMI function and the TV will automatically detect the resolution used by the HDMI source.
• To get the best picture quality, adjust the blu-ray disc player, game console or set-top box output resolution up to 1920 x 1080p.
1. Use a HDMI cable to connect the TV’s HDMI input socket to the external AV device’s HDMI output socket.
2. Plug the connected devices into the mains socket before switching on the TV.
3. Press the
button on the side panel of the TV or on
the remote control to turn on your TV.
4. Press the INPUT button to display the Source List. Use the
buttons to select HDMI and then press the
OK button to confirm.
Making Video and Audio Connections
Not all AV devices have the ability to connect to a TV, please refer to the owner’s manual of your AV device for compatibility and connection procedures.
When connecting any external AV device, do not connect the mains cable to the mains socket until all other connections are complete.
Signal Type
Separate Audio
Connection Required
HDM I
HDMI (480i/480p/576i/576p/720p/1080i/1080p*)
No
VGA I NPUT
VGA
Yes
Component Video (480i/480p/576i/576p/720p/1080i/1080p*)
Yes
SCA RT
SCART (RGB Input) No
Composite Video
Yes
Best Video Performance
*1080p: Although this TV is compatible with a 1080p input, the screen is not capable of
displaying this resolution and consequently the image will be scaled to suit the screen.
Although this TV is able to connect to a HDMI device, it is possible that some devices may not operate correctly.
100-240V ~ 50/60 Hz
AC-INPUT
VGA INPUT
SCART
AUDIO INPU T
PC
R
L
YPbVIDEO
Pr
HDMI INP UT
ANT
Rear View of TV
HDMI Cable (not included)
Blu-ray Player / DVD Player /
Recorder
Set-top BoxGame Console
Connections
L19DIGB11_IB_110315_Annie.indd 13 11年3月15日 上午11:32
GB
14
Connections
Connecting an AV Device with a Component (YPbPr) Cable
1. Use a component cable to connect the TV’s YPbPr
input sockets to an external AV device’s component output sockets.
2. Use an AV cable to connect the TV’s AUDIO(L/R) input sockets to the external AV device’s component audio output sockets. (Audio Left = white, and Audio Right = red)
Component port on the TV Y Pb Pr
Video output ports on DVD player
Y Pb Pr
Y Cb Cr
3. Plug the connected devices into the mains socket before switching on the TV.
4. Press the
button on the side panel of the TV or on
the remote control to turn on your TV.
5. Press the INPUT button to display the Source List. Use the
buttons to select YPbPr and then press the
OK button to confirm.
Connecting a Computer with a VGA Cable
1. Use a VGA cable to connect the TV’s VGA input
socket to a computer’s VGA output socket. Use an audio cable to connect the TV’s PC AUDIO input socket to the computer’s audio output socket.
2. Plug the connected devices into the mains socket before switching on the TV.
3. Press the
button on the side panel of the TV or
on the remote control to turn on your TV.
4. Press the INPUT button to display the Source List. Use the
buttons to select PC and then press
the OK button to confirm.
• The best resolution is 1360 x 768.
• If your computer is set to shut down after a few minutes of idle mode, the TV will also switch to standby due to no signal being received, this is to save energy. Press the
button on the side panel of the TV or on the remote control to restart the TV.
Rear View of TV
Computer
100-240V ~ 50/60 Hz
AC-INPUT
VGA INPUT
SCART
AUDIO INPU T
PC
R
L
YPbVIDEO
Pr
HDMI INP UT
ANT
VGA Cable
(not included)
Audio Cable (not included)
Satellite Receiver
Video Camera
Blu-ray Player / DVD Player /
Recorder
Set-top Box
Game Console
Rear View of TV
L
R
COMPONENT
OUT
Y
Pr
Pb
AV Cable (not included)
Yellow (Video)
Red (R)
White (L)
Yellow (Video)
Red (R)
White (L)
Component Cable (not included)
Pb/Cb
Pb/Cb
Pr/Cr
Pr/Cr
Y
Y
100-240V ~ 50/60 Hz
AC-INPUT
VGA INPUT
SCART
AUDIO INPU T
PC
R
L
YPbVIDEO
Pr
HDMI INP UT
ANT
L19DIGB11_IB_110315_Annie.indd 14 11年3月15日 上午11:32
GB
15
Connections
Connecting an AV Device with Composite Cable
1. Use an AV cable to connect the TV’s AUDIO(L/R)
/ VIDEO input sockets to the external AV device’s composite audio / vedio output sockets. (VIDEO = yellow, Audio Left = white, and Audio Right = red)
2. Plug the connected devices into the mains socket before switching on the TV.
3. Press the
button on the side panel of the TV or
on the remote control to turn on your TV.
4. Press the INPUT button to display the Source List. Use the
buttons to select AV and then press
the OK button to confirm.
Connecting an AV Device with a SCART Cable
1. Use a SCART cable to connect the TV’s SCART input
socket to an external AV device’s SCART output socket.
2. Plug the connected devices into the mains socket before switching on the TV.
3. Press the
button on the side panel of the TV or on
the remote control to turn on your TV.
4. The TV will change the input source to SCART automatically once the AV device is switched on.
Rear View of TV
100-240V ~ 50/60 Hz
AC-INPUT
VGA INPUT
SCART
AUDIO INPU T
PC
R
L
YPbVIDEO
Pr
HDMI INP UT
ANT
SCART Cable
(not included)
Satellite Receiver
VCR
DVD Player / Recorder
Set-top Box
Rear View of TV
100-240V ~ 50/60 Hz
AC-INPUT
VGA INPUT
SCART
AUDIO INPU T
PC
R
L
YPbVIDEO
Pr
HDMI INP UT
ANT
Satellite Receiver
Video Camera
VCR
DVD Player / Recorder
Set-top Box
Game Console
AV Cable (not included)
Yellow (Video)
White (L)
Red (R)
Yellow (Video)
Red (R)
White (L)
L19DIGB11_IB_110315_Annie.indd 15 11年3月15日 上午11:32
GB
16
Connections
Connecting the Aerial
Connect one end of the RF coaxial cable to the aerial socket on the wall and the other end of the cable to the RF (75Ω) socket at the bottom of your TV.
OR
100-240V ~ 50/60 Hz
AC-INPUT
VGA INPUT
SCART
AUDIO INP UT
PC
R
L
YPbVIDEO
Pr
HDMI IN PUT
ANT
RF coaxial cable (not included)
Do not connect the TV to the mains supply until you have completed all the connections.
Connecting a USB Storage Device
1. Switch off the TV before connecting any USB storage device.
2. Connect your USB storage device to the USB port of your TV.
3. Press the
button on the side panel of the TV or on the remote control to turn on your TV and your USB storage device.
4. Press the INPUT button to display the Source List. Use the buttons to select DMP and then press the OK button to
confirm.
• If a hard disk is used, make sure its mains adapter is connected to the mains supply.
• If a USB hub is used, make sure its mains adapter is connected to the mains supply as the total current consumption may exceed 500mA.
• The maximum supported storage space of the hard disk is 250 GB.
• The file system only supports FAT32 format.
• If you want to store the video streaming of a DTV programme, the transfer rate of the USB storage device must not be less than 5MB/s, otherwise the picture and sound of the programme will be affected and a warning statement will be shown on the screen. If this happens, please upgrade your USB storage device.
• The TV screen will be blank temporarily as it will take time to start up and stabilise the connected hard disk. This is normal and the starting time may vary depending on the brand and the memory size of the connected hard disk.
• Disconnect the USB storage device if it is not in use.
USB Cable (not included)
Adapter
Portable hard Disk
USB Hub
USB
Side View of TV
L19DIGB11_IB_110315_Annie.indd 16 11年3月15日 上午11:32
17
GB
Initial Setup
6. Channel tuning will commence. This operation may take up to 6 minutes. The display will show the progress of the tuning and the number of channels found.
7. If you want to skip the ATV tuning, press the MENU button to interrupt the tuning half way. A pop-up screen will be displayed, press the
button to select YES to confirm. You will then go straight to DTV tuning. You may repeat the above step if you also want to skip the DTV tuning. An installation reminder will appear the next time you turn on the TV.
8. After tuning is complete, the channels are arranged in a preset order. If you wish to skip channels, modify the preset order or rename channels, select Channel Edit under the Channel menu (refer to page 21-22 for details).
Channel Tuning
TV : 3 Channel(s) DTV : 0 Channel(s) Radi o : 0 Channel(s) Date : 0 Channel(s)
36%. .. 6 68.75MHz (T V)
Please press MENU to skip.
5. Press the buttons to navigate the menu and change the settings. Press the OK button to confirm.
OSD Language Select your desired language to be displayed on
the menu. The default on-screen menu language is set as English.
Country Select the country where you will operate the TV.
The default country is set as UK.
Dan sk
Deu tsch
Hrv atski
Ita liano
OSD L anguage
OK
Mag yar
Ned erlan ds
Nor sk
Pol skiEng lish
Ces ky
E k
Esp anol
~
Fra n ais
Por tugue s
Pyc ck
Fra nce
Gre ece
UK
Aus trali a
Aus tria
Cze ch
Den mark
Fin land
Cou ntry
OK
Bel gium
Bul garia
Cro atia
Hun gary
Ita ly
Lux embou rg
Ger many
Turning the TV on for the First Time
1. Connect the mains cable to the mains socket after you have
completed all the connections.
2. At this stage, the TV switches to standby mode. The red LED indicator will illuminate on the front panel of the TV.
3. In standby mode, press the
button on the side panel of the TV or on the remote control to turn the TV on. The red LED indicator will turn green.
4. The first time you turn the TV on, it will go straight into the First Time Installation menu. Please ensure the aerial is plugged
in and then press the OK button. (If you have already installed the TV using the Quick Start Guide, please go to the next step “Selecting the Input Source” on the next page.)
First Time Installation
Please ensure aerial is plugged in!
Then press OK button.
Always disconnect the TV from the mains socket
when not in use for a long period of time. The
button on the side panel of the TV or on the remote control is only used for switching the TV into standby, it does not disconnect the TV from the mains power. To completely disconnect the mains power, please remove the mains plug from the mains socket.
To the mains socket
Initial Setup
L19DIGB11_IB_110315_Annie.indd 17 11年3月15日 上午11:32
Loading...
+ 39 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use