Logik L17KBS10 Instruction Manual
GB-4 GB-5
SPECIFICATIONS
Mains supply: 230V~50Hz
Power consumption: 2200W
We continually strive to improve our products, specications may change
without prior notice.
SAFETY FIRST!
For your continued safety and to reduce the risk of injury or electric shock,
please follow all the safety precautions listed below.
• Read all the instructions carefully before using this appliance and keep
them for future reference.
• Retain the manual. If you pass the appliance on to a third party, make sure
to include this manual.
• Unplug the appliance from the mains socket when not in use, or before
cleaning any part of the appliance.
• Allow the appliance to cool fully before cleaning.
• Never immerse the appliance in water and always keep the electrical
contacts dry.
• Never place the appliance on or near a source of heat such as a cooker ring
or gas ame.
• Always place the appliance on a dry, at and stable surface.
• Avoid contact with the steam from the appliance’s spout. Take care when
pouring or relling after boiling.
• To prevent from boiling dry, do not ll the appliance with water less than
the minimum ll level as indicated on the appliance.
• Do not use the appliance to heat anything other than water.
• Do not interfere with the normal working of the switch.
• Always keep the appliance out of the reach of small children and never
allow the mains cable to hang over the edge of the work surface. Children
should be taught about the dangers of boiling water.
• This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instructions
concerning the use of the appliance by a person responsible for their
safety.
• Children should be supervised to ensure that they do not play with the
appliance.
• If the mains cable is damaged it must be replaced by the manufacturer, its
service agent, or similarly qualied persons in order to avoid a hazard.
• Do not let the mains cable overhang the edge of the work surface or allow
it to touch hot surfaces or sources of heat or ame.
Congratulations on the purchase of your new Logik Kettle.
We recommend that you spend some time reading this instruction
manual in order to fully understand all the operational features it offers.
Read all the safety instructions carefully before use and keep this
instruction manual for future reference.
Black Stainless Steel
Kettle
Instruction Manual
L17KBS10
(P.N. L17KBS10-001)
DSG Retail Ltd • Maylands Avenue • Hemel Hempstead
Herts • HP2 7TG • England
This symbol on the product or in the instructions means that your
electrical and electronic equipment should be disposed at the
end of its life separately from your household waste. There are
separate collection systems for recycling in the EU. For more
information, please contact the local authority or your retailer
where you purchased the product.
Visit Partmaster.co.uk today for the easiest way to
buy electrical spares and accessories. With over 1
million spares and accessories available we can
deliver direct to your door the very next day. Visit www.partmaster.co.uk or call
0844 800 3456 (UK customers only) Calls charged at National Rate.
GB-1 GB-2
GB-3
PRODUCT OVERVIEW
UNPACKING
Remove all packaging from the kettle. Retain the packaging. If you dispose
of it please do so according to local regulations.
The following items are included:
FIRST TIME USE
Clean your kettle by boiling a full kettle of water twice and then discarding
the water.
KEEPING THE MAINS CABLE TIDY
Extend the mains cable in the kettle stand to
the required length. Locate the mains cable
in one of the slots in the stand. For safety it
is recommended that the length of exposed
mains cable is kept as short as possible.
Place the kettle stand on a rm level surface
and plug in the mains plug at a standard
mains socket (240 Volt 13 Amp rated).
Instruction Manual
(Part number: L17KBS10-001)
The kettle
If items are missing or damaged, please contact Partmaster (UK only)
Tel. 0844 800 3456 for assistance.
This kettle must only be used with the stand provided.
DESCALING THE KETTLE
Depending on the hardness of the water
in your area, limescale may be deposited
on the heating element and the inside of
the kettle. This normal build-up is not
harmful to health but an excessive
amount of scale may aect the
performance of the kettle.
To descale, ll the kettle with distilled
water up to three-quarters of the Max
level and bring the water to boil. After the
kettle has switched o, add a descaling
solution following the manufacturers
instructions. Never attempt to descale the
kettle by chipping or scraping with a
sharp implement.
CLEANING THE KETTLE
The kettle exterior should be cleaned with a soft damp cloth. Do not use
abrasive cleaners or scouring pads which may damage the nish of the kettle.
Never immerse the kettle or kettle stand in water and always keep the electrical
contacts dry. Disconnect from the mains before cleaning the kettle stand.
CLEANING THE REMOVABLE SCALE FILTER
To prevent loose particles of limescale being poured into your beverage, your
kettle is tted with a scale lter. You may remove the lter and t it back in
after cleaning.
FILLING THE KETTLE
Slide the switch to open the lid and ll the kettle with the required amount of
water.
Do not exceed the maximum ll level (Max 1.7L) as indicated inside the kettle
and not less than the minimum ll level (Min 0.5L).
Do not insert any foreign objects or allow any liquid to spill into the Power
Connector Hole.
WHEN THE WATER HAS BOILED
The kettle will automatically switch o . The
light inside the kettle will go o.
Ensure that the switch is not
obstructed and the lid is rmly closed.
The kettle will not turn o if the
switch is obstructed or if the lid is
open.
If there is insucient water in the kettle, the automatic safety cut-out
will operate. If this happens, allow the kettle to cool for ten minutes before
relling with cold water and re-boiling.
If the kettle is overlled, boiling water may be ejected from the spout and
cause scalding.
After removing the kettle, there may be some water on the surface of the
stand. This is condensation from the steam that causes the kettle to
automatically switch o after boiling. This is normal and should not be a
cause for alarm.
Never open the lid while the water is
boiling. The steam coming out from
the kettle is very hot.
SWITCHING ON
Place the kettle on the stand and press the
power switch downward. The light inside
the kettle will illuminate to indicate that the
kettle is heating. This is visible through the
glass lid.
Stand
Spout
Lid
Fill Level
Power Switch
Open Button
Handle
Power Connector Hole
To remove the lter, open the lid,
press and lift up the lter from the
bracket at the spout.
To t in the lter, open the lid, place
the lter inside the bracket at the
spout, locate the 3 slots shown by the
arrows above and t it in place.
Loading...