Logic Six LGSIX/01 Engineering Information

Download

Intruder alarm system

Engineering Information

LGSIX/01 Logic Six panel with two pre learnt Keyfobs

The above intruder system is designed to comply with the installation requirements of BS 4737 1986/87.

4188-753 issue 1_1/03 1

Accenta

mini

Learn

Error

Day

1 2 3 4 5 6

Power

ZONE

Features

6 Security zones

PA input

Tamper input

Outputs for External siren (Bell) and Strobe

Pre-configured Part set program selectable by DIP switch.

Entry Time duration selectable by DIP switch

Entry Deviate

Alarm Cycle Counter

Strobe confirmation on Set

Memorises first and subsequent zone intrusions in one alarm period

Walk Test facilities by push button control

Alarm Test facilities by push button control

Battery capacity of up to 2.1Ah

Up to 8 keyfobs can be used with the panel (2 Keyfobs supplied pre learnt)

Learn mode to learn new keyfobs

Erase mode to disable lost or stolen keyfobs

2 4188-753 issue 1_1/03

Engineering information

Contents

Features -------------------2 Installation Design --------------3 Fixing the control panel -----------3 Wiring the system --------------4 Tamper network ---------------4 Security zones ----------------5 PA circuit ------------------6 Extension speaker --------------7 External siren Output (Bell box) -------8 13V Supply output --------------9 Set ---------------------9 Factory set condition -------------10 Zone Function ----------------10 First Power up ----------------11 Mains Connection --------------11 Testing the system --------------12 System indications --------------12 Programs ------------------12 Walk tests ------------------13 Alarm tests -----------------13 How to learn new keyfobs ----------14 How to re-learn all keyfobs ----------15 How to learn keyfobs if non are recognised - - 16 Re-arm -------------------17 Alarm Cycle Counter-------------17 Faults --------------------18 Specification-----------------19 Servicing organisation Details --------20 Parts --------------------20

Installation Design

The purchase of this alarm system represents a major step forward in the protection of the property and its occupants. It is important to plan the installation before proceeding following the procedures and advice contained in this manual.

Plan the position of each part of the alarm system and the cable runs. Detectors should be sited with particular regard to the degree of coverage required

and the function of each of the zones.

All of the system wiring is connected directly to the panel. The intruder panel must be installed near an entry/exit point.

One additional internal sound speaker is recommended, it will provide high volume alarm tones and low volume

entry/exit tones. Speakers should be positioned to provide good sound distribution throughout the building and so that the exit tone is audible outside the main entry / exit door. This will enable the system operator to check that the system is setting correctly.

Finally note that the total current output of this control system (in alarm condition) is 1A when supported by a fully

charged battery. Calculate the total current consumption of every part of the system including the panel, external siren with strobe light (bell box) and detectors to ensure that this rating is not exceeded.

Depending on which area you

live, you may be required, by

law to notify the Local

Authority and Police of the

new security alarm installation. The local authority requirements may differ from area to area, therefore it is advisable to contact local environmental officer to obtain full details of your area requirements.

Fixing the control panel

Caution: When positioning the control panel ensure that it is located in a dry place away from damp areas.

a. Remove the front cover(s) from the

base assembly.

Disconnect the transformer wires from the board, these are marked AC. Carefully remove the board by gently pushing down the holding clips on the bottom edge of the board and withdraw it from the base.

Note: When replacing the board align it on the round support pillars to the bottom and allow it to click down past the clips at the top of the case. Refit the transformer wires into the terminal.

4188-753 issue 1_1/03 3

Logic Six intruder system







ZONES

Error

Learn

TOTAL

Power







b. Fit the panel to the wall with suitable

fixings. Ensure the wall surface is flat to prevent base distortion. There are cable entry holes provided in the rear of the base and around the outside edges through the thinned out plastic sections which may be cut away as required.

c. The hole provided adjacent to the

mains transformer is a dedicated mains cable entry point.

Board

There are three fuses mounted on the circuit board, all are 20mm quick blow.

F1 1.6A - to protect the +ve line of 12V battery F3 1A - to protect the Speaker 13V supply F5 1A - to protect the Siren & Strobe

supply As supplied, there are wire links are fitted across

the PA and Tamper terminals to represent a closed circuit.

Wiring the system

Caution: Always power-down the panel when wiring external circuits, to prevent damage to the panel electronics.

Systematically wire and test each circuit:

Zones, Tamper and PA circuits

Finish by wiring any additional extension speaker sounders, external siren (bell) / strobe and the 13V supply.

Tamper network

The Tamper circuit is used to protect all cables and detectors in the system from unauthorised access including the panel cover.

The zone and PA tampers should be series wired and connected to the TAMP terminals. The terminalsT&Aarefortheexternal siren tamper. Tamper alarms that occur in the Day mode operate internal sounders only. Tamper alarms in Set cause a full alarm condition. Tamper is indicated by the Tamper TA indicator.

4 4188-753 issue 1_1/03

Engineering information

TAMP

+13V 0V

STROBE

SW1

SCB

BELL

SET +ve

1A 1A 1.6A

BELL/STROBE

13V / SPEAKER

BATTERY

BATT

F1F3F5

VR1

VOLUME

214

Factory fitted links

LD2 LD8 LD9 LD4 LD10 LD5 LD11

LD23

LD12

LD22

LD6

LD3

SW2

WALK / ALARM TEST

TAMP

OFF

ENTRY TIME

PART SET

15S

30S

Mounting holes

Cable entry

holes

Danger

High Voltage

230V 50Hz 0.2A

FUSE T125mA 250V

(ANTI-SURGE)

Security zones

Note: The panel is supplied with wire links for unused zones. All unused zones must have links fitted to disable the zone.

It is recommended that no more than 10 magnetic contacts are connected to the same zone.

4188-753 issue 1_1/03 5

Logic Six intruder system

214

Panel

Alarm

TAMP

+13V 0V

PIR

All unused zones must have links fitted to disable the zone.

Board

PIR

Door Contact

Terminal block is not supplied

Tamp

PA circuit

Any quantity of normally closed type personal attack button may be wired in series and then connected to the PA circuit.

Operational in Day and Set, the PA circuit will cause a full alarm condition when activated. PA is indicated on the control panel as PA.

PA buttons may be fitted near the front door, or in a bedroom.

6 4188-753 issue 1_1/03

Engineering information

TAM P

+13V 0V

Board

Panel

Panic Button

214

Extension speaker

Extension speaker may be connected to the loudspeaker terminals to produce high volume alarm tones and low volume entry / exit fault tones.

A 16 ohms extension speaker may be wired across the speaker terminals. Mounted in convenient position within the installation the extension speaker will reproduce all of the alarm tones generated by the control panel.

A control marked VOLUME in the centre of the board may be used to adjust the low volume entry/exit tones to suit environmental conditions.

4188-753 issue 1_1/03 7

Logic Six intruder system

STROBE

SCB

BELL

SET

+ve

BELL/STROBE

Panel

Board

13V SPEAKER

16 Ohms Extension Speaker

VR1

VOLUME

External siren Output (Bell box)

The external siren (bell box) is usually installed in a high position from where the siren could be seen and heard.

Terminal TADBareforconnecting to the external siren. These terminals provide a power/hold-off supply, sounder trigger and tamper circuit to protect the external siren housing.

The terminals are summarised as follows: T - -Ve tamper return A - -Ve supply (0V) D - +Ve supply (12V) B- -Ve Sounder trigger For ease of installation, ADE external sirens and modules use the same markings. Where a discrete external siren is used, it should be connected to terminalsD&B.TerminalsT&A

are then used for tamper protection for the housing.

8 4188-753 issue 1_1/03

Engineering information

STROBE

SCB

BELL

SET

+ve

BELL/STROBE

Sonade

Panel

Board

+- TEADB

STROBE

Where self contained / powered sounders are used, carefully follow the manufacturers instructions, match each of the terminals to those above.

13V Supply output

The 13V output is to power detectors which require a voltage supply (PIR detectors etc). The supply is present at all times and may be used to supply a total load of 350mA.

Set +VE

The output , marked SET +VE is used with latching detectors. The output becomes positive on correct Set of the system and is removed on UNSETTING the system.

4188-753 issue 1_1/03 9

Logic Six intruder system

# Terminal block is not supplied

STROBE

SCB

BELL

SET +ve

BELL/STROBE

Sonade

Panel

Board

+- TEADB

STROBE

Sonade

+- TEADB

STROBE

Factory set condition

Keyfob 1 and 2 (supplied) - Learnt Keyfobs 3 to 8 (optional) - - Require learning External siren Bell Duration 20 minutes External siren Bell Delay - - No delay

Full Set

Zone1 ---------Timed Zone 2 ---------Time inhibited Zone 3, 4,5&6 ----Immediate Entry time (timed zone)- 30seconds(default)

(15 seconds via setting DIP switch)

Exit mode is timed - - - 30 seconds

Part set (DIP switch selectable see page 12)

Zone 1,2&3 -----Timed Zone 4 ---------Immediate zone Zone5&6-------Omitted zones Entry time (timed zone)- 30seconds(default)

(15 seconds via setting DIP switch)

Silent Exit mode is timed 30 seconds

Applicable for both full and part set:

Tamper TA 24 hour alarm Personal Attack PA 24 hour alarm Security Zones -------Zones 1…6 Zone debounce period - - - 640mS ALL zones

Zone Function

The following are definitions of zone functions:

Timed : This function would be used to protect the main entry/exit door of the entry route.

Time inhibited (Walk through) : This is a zone which, on setting the panel, allows access to the Entry / Exit zone. However, if the panel is set and an time inhibited zone is triggered before an Entry /Exit zone then an alarm will be generated immediately.

Immediate: This is a zone which will, when entered, go into alarm when the panel is set.

The Entry deviate feature permits an immediate zone to be activated during the entry period without causing a full alarm.

Unused : An unused zone that has been linked out will be ignored by the panel.

10 4188-753 issue 1_1/03

Engineering information

First Power up

Before power up fit the top cover on to the base and connect the speaker wires. Leave the cover in position throughout the reset of the installation.

Check that the factory fitted links are connected to terminals unused Zones, PA, TAMP and T-A.

b. Fit the battery wires to the BATT

terminals on the Board, Red to + and Black to -.

c. On connecting the battery the system

will now go into alarm condition, the Tamper LED is lit and the Power LED gives a flashing indication:

d. Fit the cover to hold down the tamper

spring at the bottom centre of the board.

Offer a keyfob to the centre depression on the panel. Note the Tamper LED and Alarm switches Off and the

LED is lit.

Note: If you do not withdraw the keyfob after it is recognised by the panel then you run the risk of entering an undesired mode of operation.

Mains Connection

The mains power should be connected using a 3 core cable of not less than 0.75mm sq. from a

fused spur to the mains connector inside the control panel. The 2 A fused spur must be located close to the control panel.

Note: The mains supply must be connected by a technically competent person and according to current IEE regulations.

Caution: To avoid the risk of electrical shock you must always totally isolate the mains supply before opening the control panel cover(s).

Mains Input Fuse rating: 125mA, 250V type T (anti surge) and of a type approved to IEC 127 part 2 sheet III.

On connecting the mains supply to the panel the power indicator is lit.

(Changes from flashing to steady)

4188-753 issue 1_1/03 11

Logic Six intruder system

Transformer

125mA Fuse

Panel

1.6A

BATTERY

BATT

Board

(red)

Black -

12V battery

Alarm

Power

Offer keyfob to the Panel and withdraw

Keyfob recognition beep

Accenta

mini

1 2 3 4 5 6TAPA

ZONE

Learn

Error

Day

Power

Transformer

125mA Fuse

Panel

1.6A

BATTERY

BATT

Board

(red)

Black -

12V battery

2A Fused Spur unit

Dedicated mains supply

from consumer unit.

Day

Power

Testing the system

Complete the wiring of the system and then:

Program the panel.

Fully test the system and ensure it is fault free

Fill in the installation log at the back of this manual and retain if for future reference.

Finally explain the operation of the system to the end user. The Operating Instructions

are attached to the centre of this manual. Detach them and leave them with the user.

Key

System indications

- Unset system indication

- Set system indication

Note: The Power LED will give a flashing indication when there is a mains supply failure to the panel.

Programs

The panel offers Full Set or selectable Part Set routine and programmable entry time. As default the panel is set for Full Set and an Entry time of 30 seconds.

Full Set : Arms all of the zones and become Set as the user leaves the property after the Exit time of 30 seconds.

Part Set : To protect the downstairs areas of the house at night the Zones 5 and 6 are omitted from being set as the user goes upstairs after the Exit time of 30 seconds.

Note: The Part Set assumes Zone 5 and Zone 6 are upstairs zones.

Entry time 30 seconds (factory default): Allows the user to enter the premises and unset the system within 30 seconds.

Entry time 15 seconds : Allows the user to enter the premises and unset the system within 15 seconds.

12 4188-753 issue 1_1/03

Engineering information

Powe

Day

Powe

LED steady On indication

LED Off

Strobe

External Siren

NOTE: In general a flat beep is an indication of not recognised keyfobs.

Sound description

Internal sound

External devices

LED flashing indication

OFF

ENTRY TIME

PART SET

15S

30S

Board

Panel

Walk tests

The walk test function allows each detector to be checked in order to verify that they are functioning correctly.

To enter walk test the panel must be in Day

mode with the DAY LED lit:

a. Open the bottom cover of the panel.

Note this will cause a tamper alarm.

b. Present a recognised keyfob and the

alarm sound stops. Tamper TA LED will flash to give a tamper indication.

c. Momentarily press the PCB mounted

push button. Note do not hold the button down or it will go into Walk test.

The DAY LED starts to flash.

d. Upon activation of any zone, the

relevant ZONE led will latch up and a“Zone fault” tone is emitted.

e. Pressing the push button again at any

time will clear the latched LED and walk test is restarted.

f. On completion of Walk Test, close the

panel cover and an “OK” tone is emitted and the panel returns to Day

mode with the Day LED lit.

Alarm tests

The alarm test function allows you to test the Strobe, Siren (Bell), Low and High volume sounders of the system, SET+ output.

The Alarm Test mode could also be activated while in Walk Test mode, if you are doing this go straight to step d).

To enter Walk Test mode the panel must be in

Day mode with the DAY LED lit:

a. Ensure the bottom cover of the panel is

open. Note this will cause a tamper alarm.

b. Present a recognised keyfob and the

alarm sound stops. Tamper TA LED will flash to give a tamper indication.

d. Press the PCB mounted push button

and hold for 3 seconds.

e. The tests below are performed

consecutively. Automatic advance to the next test after 3 seconds.

1) Low Volume Sounders

2) High Volume Sounders and Strobe

3) External Bell and Strobe

4) SET+ output and Strobe

f. On completion of Alarm Test an “OK”

tone is emitted and the panel returns to

Day mode with the DAY LED lit. Close the bottom cover of the panel and the Tamper TA LED switches Off.

4188-753 issue 1_1/03 13

Logic Six intruder system

Board

Panel

SW2

WALK / ALARM TEST

Board

Panel

SW2

WALK / ALARM TEST

How to learn new keyfobs

14 4188-753 issue 1_1/03

Engineering information

Offer a slightly touch it on the centre depression of the A learnt indication is given of the when the flashing LED changes to steady On indication and there is a recognition beep given by the local sounder. Shortly after the next numbered LED will start flashing. Withdraw the learnt keyfob.

You now have up to 10 seconds to learn another new keyfob.

For keyfobs 7 and 8 the indications are TA and PA LEDs respectively.

new keyfob

Panel. new keyfob

ZONE

keyfob recognised beep

Panel

New keyfob

When an unrecognised keyfob is offered to the it will cause the

LED to be lit and a continuous sound is emitted from the

local sounder.

Hold the

The will timeout after 10 seconds if no action is taken to learn new keyfob

panel

Error

learn mode

recognised such that it touches the centre

depression on the Panel and keep it there without movement for

You will hear a keyfob recognition beep and

later five rapid beeps from the local sounder.

You are now in the The LED will give a flashing indication and the LEDs change from flashing to steady On indication to show recognised or . The is now ready to learn signalled by the next flashing LED. Withdraw the keyfob.

In the when an already learnt keyfob is offered to the an Error indication will be given.

‘learnt’ keyfob

learnt keyfob Panel

new keyfobs

Panel

10 seconds. 10 seconds

learn mode. Learn

ZONE

learn mode

Repeat to learn the

Once all the keyfobs are recognised ‘learnt’ by the wait for just over 10 seconds for the Panel to exit the this is announced by two beeps from the local sounder and return to mode indication.

new keyfob.

Panel

learn mode,

Day

x 2 beeps

keyfob recognised beep

Panel

Learnt keyfob

x 5 rapid beeps

Hold for 10 seconds

Power

Day

Using a recognised the can learn further keyfobs. A total of 8 keyfobs are recognised by a Panel. You may want to do this if you have acquired additional keyfobs. Using these procedures the panel will still memorise previously learnt keyfobs. New k

learnt keyfob panel

eyfobs must be learnt by the .panel

Ensure the is in the day mode with the LED lit. You should have one and the new keyfobs available.

panel

learnt keyfob

Day

Indication given assumes 2 keyfobs were previously learnt by the Panel

1 42 3

Learn

Power

Day

Learn

How to re-learn all keyfobs

4188-753 issue 1_1/03 15

Logic Six intruder system

By entering the in this manner you will erase all recognition of previously learnt keyfobs at the Panel, except for the one used to enter the .

learn mode

Offer the slightly touch it on the centre depression of the A learnt indication is given of the when the flashing LED changes to steady On indication and there is a recognition beep given by the local sounder. Shortly after the next numbered indicator will start flashing. Withdraw the learnt keyfob.

You now have up to 10 seconds to start learning another keyfob.

next keyfob Panel

next keyfob ZONE

ZONE

keyfob recognised beep

Panel

Next keyfob

When an unrecognised keyfob is offered to the it will cause the LED to be lit and continuous sound to be emitted from the local sounder.

Hold the

The will timeout after if no actions is taken to learn the next keyfob

Panel

Error

learn mode 10 seconds

recognised slighty touching the centre depression on the and keep it there without movement for . Initially you will hear a keyfob recognition beep and

later five rapid beeps from the local sounder. After another you will hear 5 rapid beep tone from the local sounder. You are now in the The LED will give a flashing indication and the LED changes from flashing to steady On indication to recognise the . The is now ready to learn the , signalled by the

LED flashing. Withdraw the learnt keyfob.

In the when an already learnt keyfob is offered to the

an Error indication will be given.

‘learnt’ keyfob

Panel

learnt keyfob

Panel next keyfob

Panel,

20 seconds

10 seconds

learn mode. Learn

ZONE 1

ZONE 2

learn mode

Repeat to learn the

Once all the keyfobs are recognised ‘learnt’ by the wait for just over 10 seconds for the Panel to exit the this is announced by two beeps from the local sounder and return to mode indication.

next keyfob.

Panel

learn mode,

Day

x 2 beeps

keyfob recognised beep

Panel

Learnt keyfob

x 5 rapid beeps

Hold for 20 seconds

Using a recognised the can re-learn up to 8 keyfobs. You may want to do this after a keyfob is lost or stolen and you want to prevent the use of it to operate the system.

learnt keyfob Panel

Keyfobs must

be learnt by each installed in a systemPanel

Ensure the is in the day mode with the LED lit. You must have one and up to 7 further keyfobs to be learnt. Have all the keyfobs available.

Panel

learnt keyfob

Day

x 5 rapid beeps

Power

Day

1 2 3

Learn

1 2

Learn

1 2 3

Learn

Power

Day

How to learn keyfobs if none are recognised

16 4188-753 issue 1_1/03

Engineering information

Offer the slightly touching it on the centre depression of the A learnt indication is given of the when the flashing LED changes to steady On indication and there is a recognition beep given by the local sounder. Shortly after the next numbered LED starts flashing. Withdraw the learnt keyfob.

next keyfob

Panel. next keyfob

ZONE

You now have up to to learn the10 seconds next keyfob.

keyfob recognised beep

Panel

Next keyfob

Hold the slightly touching it on the centre depression of the .

first keyfob

Panel

Once the is acknowledged by the the LED changes from flashing to steady and there is a recognition beep given by the local sounder. Withdraw the learnt keyfob. The is now ready to learn the , signalled by LED flashing.

first keyfob Panel

Panel next keyfob

ZONE 1

ZONE 2

keyfob recognised beep

Panel

first keyfob

x 5 rapid beeps

Now remove the link between Z1 and Set.

x 2 beeps

Hold

Ensure the is connected to the intruder system and the link is fitted on the

Power up the intruder system you will hear five rapid beeps to acknowledge the is in the .

Panel

Panel PCB between Z1 and Set.

Panel Learn mode

The will NOT timeout until the first keyfob is learnt.learn mode

You will only need to learn keyfobs in this manner if no keyfobs are recognised by the

You must have all the keyfobs to be

learnt available. Keyfobs can be learnt by each installed in a system

Panel.

Panel

A can

learn up to 8 keyfobs following power up of the intruder system.

Panel

POWER UP THE SYSTEM

Power

Day

Learn

1 ZONE

STROBE

SCB

BELL

SET

1 2

Learn

2 3

Repeat to learn the next keyfob.

Once all the keyfobs are recognised ‘learnt’ by the Panel wait for just over and the Panel will exit the10 seconds learn mode, this is announced by two beeps from the local sounder and return to Day mode indication.

NVM Error

A Non Volatile Memory NVM error indication is given by a flashing Error LED. If an NVM error occurs then you will need to re-learn all the keyfobs, see page 16.

Re-arm

After an alarm the panel will automatically reset itself when the external siren (bell box) 20 minute timer has expired.

Alarm Cycle Counter

An alarm cycle is considered as the duration of an alarm from trigger to the end of 20 minutes operation of the external siren. The panel allows three alarm cycles during either set or unset period. When the third alarm cycle expires the panel is shut down, the storobe continues to operate. The panel is unset in the normal way see operating instructions.

4188-753 issue 1_1/03 17

Logic Six intruder system

Faults

Fault conditions are often the result of minor installation errors or misinterpretation of the equipment being installed. The following points outline the most common installation and commissioning faults.

If a tamper TA or Personal Attack PA fault is present on the system, a flashing indication is given of first fault, it will go to a lock out condition (showing the appropriate indication). Rectify the fault and offer the keyfob to the panel to remove the fault.

b. The most common cause of a zone not

responding to detection is incorrect wiring. Normally closed detectors must be wired together in a series loop before connecting into the appropriate ZONE terminals. Tampers are series wired in the same manner.

c. Where a permanent zone fault is

showing and the loop resistance is found to be in order, the most probable cause is a short circuit between the zone wiring and the tamper wiring. When measured with a multimeter the series resistance between the zone and tamper wiring should be infinitely high.

d. If totally lost as to the cause of a fault,

remove ALL wiring from the Board. Refit the 9-links and test the system. Never fit links to any positions other than those marked on the Board.

e. Before testing or replacing any fuses,

ALL power must be removed. Fuses which fail continually are almost certainly the result of a short circuit or low resistance across the 13V supply or external siren (bell box) supply (terminal D).

Whenever working close to the mains supply or connector, you should exercise extreme caution always isolate the mains supply before

removing the control panel covers.

Where normally open and closed detectors are being used these must be wired to a zone in the manner shown.

The example below shows how to wire normally open detectors on zones 3.

The example below shows how to wire normally open detector on zones 3 and a normally closed detector on zone 4.

f. Where Pressure mats are being used

these must be connected to a zone in the manner shown. The example below shows pressure mats connected to zones 3.

18 4188-753 issue 1_1/03

Engineering information

214

TAMP

+13V 0V

Board

Panel

Normally open detectors

214

TAMP

+13V 0V

Board

Panel

Normally open detectors

Normally closed detector

214

TAMP

+13V 0V

Board

Panel

Pressure Mats

Specification

Indicators on Control panel

Zone 1-6 (red), Tamper TA (amber), Personal Attack-PA, Power, Learn (amber), Error (red) and

Day (green) 6 Zones +ve loop, Security zones Tamper -ve loop, always active PA +ve loop, always active User keyfobs Up to 8 keyfobs can be

learnt to operate with the

panel Keyfob operating

range

20mm nominal form

centre depression Proximity reader 125KHz inductive External siren

(Bell box) Output

12V, time 20 minutes

continuous Strobe Output 12V latching Extension Speaker

16 Ohms 260mA Exit time 30 seconds Entry time Programmable by DIP

switch 15 seconds or

30 seconds Full/Part Set Programmable by DIP

switch Walk and Alarm

Tests

Selectable by push

button switch Zone Input Delay 640mS Set +ve Output 0V in Day (sinking

40mA)

12V in Set (Sourcing

10mA) Current

Consumption Control panel

Standby 80mA

Alarm 250mA

Low voltage output

13.8V dc stabilised

(+/-5%) up to 350mA Rechargeable

Battery

12V, 1.2 or 2.1Ah

Charge Voltage 13.8V dc (+/-5%) Board Fuses 1.6A & 1A 20mm quick

blow Mains Input fuse 125mA, 250V type T

(anti-surge) type

approved to IEC 127,

part 2 sheet III

Total Current Output

1A when supported by a fully charged battery

Mains Supply Voltage

230V (+/-10%) 50Hz max load 0.2A

Ambient Operating temperature

0°C to 40°C

Enclosure construction

3mm Polycarbonate

Panel dimension H 200mm W 253mm

D 55mm

Keyfob dimension L 58.5mm W 18.5mm

4188-753 issue 1_1/03 19

Logic Six intruder system

Servicing organisation Details

Servicing organisation name:

_______________________________________ Telephone number:

______________________________________ Date of installation:

______________________________________ Account Number:

_____________________________________

Parts

Below is a list of approved parts and accessories.

LGSIX/01 Logic Six panel

(supplied with 2 learnt keyfobs)

SS/F Spare Keyfob

20 4188-753 issue 1_1/03

Engineering information

The Logic Six panel conforms to the requirements of the European R&TTE directive 1999/5/EC and carries the CE mark. This product is intended for use in the UK.

For Technical Support

 : 01268 563270

ED&S The Arnold Centre Paycocke Road Basildon Essex SW14 3EA

Resistance Area protection and equipment used (eg PIR, Contacts..)

Zone 1

Zone 2

Zone 3

Zone 4

Zone 5

Zone 6

Intruder alarm system

Operating Instructions

Servicing organisation details

Servicing organisation (Installer) name: ______________________________________________

Telephone number: _______________________________________________________________

Date of installation: _______________________________________________________________

Account number: _________________________________________________________________

Accenta

mini

Learn

Error

Day

1 2 3 4 5 6

Power

ZONE

System installation

This booklet tells you how to operate your intruder alarm system. To simplify this booklet we have assumed that the alarm system has been installed by a professional intruder alarm system installer (the installer), and that the system is operated in a “typical” way. Aspects of your system that are not “typical” will be described by your installer.

Note: If you have any questions about

your intruder system, then consult your installer, see contact details on the front page.

Keyfobs

To operate the alarm system you will need the keyfobs supplied with the panel. These keyfobs are recognised by the panel and will operate your system. If you should need further keyfobs you should consult your installer, up to 8 maximum keyfobs can operate your system.

Operating instructions

Keyfobs Supplied with the panel

Additional keyfobs

Personal Attack

If you are under threat, or are being attacked, you can activate the alarm by operating the personal attack buttom in your system. The alarm system will produce a loud alarm sound, and the external siren will be turned on.

Power Indicator

The Power indicator on the control panel will light whenever the mains power supply is present. If mains power fails then the Power indicator will flash, but the system will run from its backup battery for several hours. If the Power indicator goes out when mains power is present then a fault may have developed on your system and you should contact your installer.

Key

Logic Six intruder system

LED steady On indication

LED Off

Strobe On

External Siren

NOTE: In general a flat beep is an indication of not recognised keyfobs.

Sound description

Internal sound

External devices

LED flashing indication

How to Set the system

When you leave your premises you will need to set (or turn on) the intruder alarm system. Before setting the system you should ensure that the premises have been completely vacated and that all doors and windows are closed. Ensure that pets do not have access to the protected areas as they can cause a false alarm, unless pet immune detectors have been used, ask your installer for more information.

Operating instructions

Panel

Offer keyfob to the Panel and withdraw

Keyfob recognition beep

The indicator should be lit at the Panel. Offer a to the Panel and withdraw it as soon as you hear the

from the local sounder.

The system will produce the exit beep tone and you should leave the premises by the exit route recommended by your installer. The system will set when the exit beep tone stops.

Day

keyfob

keyfob recognition

beep tone

Note the panel LEDs will flash consecutively from right to left, PA to Zone1 LED during Set operation. If however there is an open zone then the relevant ZONE LED will be lit and a sound indication is given. If this is the case then investigate the cause and ensure all zones are closed.

Insistent Exit beeps

(for final 10 seonds)

Once any operation is performed using the keyfob withdraw it away from the panel, wait for duration before next use of the keyfob to operate the system.

3 seconds

Power

Day

Power

The external strobe will operate for , which provides a confirmation of SET operation.

5 seconds

Exit beep

1 2 3 4 5 6TAPA

ZONE

How to Unset the system

When you enter your premises you will need to unset (or turn off) the system. If your system had gone into alarm then be aware that intruders may be in the premises. Seek assistance before investigating the cause of the alarm and unset the system.

Logic Six intruder system

Panel

Offer keyfob to the Panel and withdraw

Keyfob recognition beep

Enter your premises by the route recommended by your installer. The system will produce an entry beep tone.

Offer a to the Panel and withdraw it as soon as you hear the beep tone from the local sounder.

The system will stop the entry beep tone and light the green LED.

If any Zone, Tamper or Attack LEDs light up then an alarm has occurred, and an intrusion may have taken place. Seek assistance before investigating further as intruders may still be on the premises. The first alarm indication given by a flashing indicator, with all subsequent alarm indication given as a steady indication. These indications will remain until the next time the system is unset.

keyfob

keyfob recognition

Day

Note the panel LEDs will flash consecutively from left to right, from to the LED, during Unset operation.

Zone1 PA

Entry beep

Day

Power

Day

TA PA

Power

1 2 3 4 5 6TAPA

ZONE

How to part set the system

If your installer has programmed your system for part set operation you will be able to set some zones of the system while others remain unset. Part set operation is often used at night time, and it will permit you to freely walk around the bedrooms while the living area and outside doors are protected.

Before part setting the system at night time you should ensure the downstairs of the premises have been completely vacated and that all doors and windows are closed. Ensure that pets do not have access to the protected areas as they can cause a false alarm.

Operating instructions

Panel

Within10 seconds offer keyfob second time to the Panel and withdraw

Keyfob recognition beep

The indicator should be lit at the Panel. Offer a to the Panel and withdraw it as soon as you hear the

from the local sounder. Ensure ZONE 1 to ZONE 4 LEDs are Off. If they remain On, investigate the cause and ensure the zones are closed. The system will produce the exit beep tone. Within 10 seconds o

and you should

now move to area omitted by part set.

The system will set after 30 seconds when two consecutive beep is emitted.

Day

keyfob

keyfob recognition

beep tone

ffer a a second time to the Panel and withdraw it, you hear another

from the local sounder

The indicator should be flashing at the Panel.

keyfob

keyfob recognition beep

tone

Day

Exit beep

Once a any operation is performed using the keyfob withdraw it away from the panel, wait for 3 seconds duration before next use of the keyfob to operate the system.

Power

Day

Power

Panel

Offer keyfob to the Panel and withdraw

Day

2 x Set beep when panel is set

Entry time:________________

Area protected

Zone name Full set Part Set

Zone 1 T T

Zone 2 TI T

Zone 3 I T

Zone 4 I I

Zone 5 I O

Zone 6 I O

O = Omited T = Timed (Entry/Exit - Zone) TI = Time Inhibited (Access zone to keypad) I = Immediate (Zone armed to give full alarm)

Logic Six intruder system

8 4188-753 issue 1_1/03

Operating instructions

The Logic Six panel conforms to the requirements of the European R&TTE directive 1999/5/EC and carries the CE mark. This product is intended for use in the UK.

Logic Six LGSIX/01 Engineering Information

Specifications and Main Features

Frequently Asked Questions

User Manual