LOGICDATA SMARTneo-2G User Manual

MANUAL

Document Version 1.0 /July 2019

SMARTneo-2G

Cascading

SMARTNEO-2G: CASCADING MANUAL // PAGE 2

SMARTneo-2G - Cascading Manual

Document Version 1.0/ Juli 2019

The German language version is the original

LOGICDATA Electronic & Software Entwicklungs GmbH

Wirtschaftspark 18

8530 Deutschlandsberg

Austria

Phone: [phone]

Fax: [phone]

Internet: http://www.logicdata.net

Email: o[e-mail]

INFO This manual is valid for SMARTneo-2G Control Boxes.

SMARTNEO-2G: CASCADING MANUAL // PAGE 3

1 QUICK REFERENCE

The Quick Reference is not a substitute for the product documentation. For your own

INFO

Required components For detailed instructions, see the “Required Components” subchapter for

3 4

safety, read the complete product documentation before connecting the components
to form a Cascading System and putting it into operation.

your chosen conguration.

5

1

1 2

SAVE

2

Fig. 1: Required components

1 1 Hand Control

2 2 SMARTneo-2G Control Boxes

3 2 to 4 Actuators

4 1 Cascading Cable

5 2 Power Cables

4

3

SMARTNEO-2G: CASCADING MANUAL // PAGE 4

Cascading System with 2 Actuators For detailed instructions, see chapter 6.3.5 on page 15

1 2 3

1 2

3 4

SAVE

4 5

1 2

3 4

SAVE

Cascading System with 3 Actuators For detailed instructions, see chapter 6.6 on page 16

1 2 3

1 2

3 4

SAVE

4 5

1 2

3 4

SAVE

SMARTNEO-2G: CASCADING MANUAL // PAGE 5

Cascading System with 4 Actuators For detailed instructions, see chapter 6.7 on page 17

1 2 3

1 2

3 4

SAVE

4 5

1 2

3 4

SAVE

Performing the Reference Drive For detailed instructions, see chapter 7.1 on page 18

CLICK

Factory Reset For detailed instructions, see chapter 7.2 on page 18

Comfort:

3s

1 2

Basic:

O73

S 5 S O

Hold Hold

SAVE

SMARTNEO-2G: CASCADING MANUAL // PAGE 6

CONTENTS

1 Quick reference 3

2 General information 8

2.1 Other applicable documents 8

2.2 Copyright 8

2.3 Royalty-free use of images and text 8

2.4 Trademarks 8

3 Safety 9

3.1 Target audience 9

3.2 General safety regulations 9

3.3 Intended use 9

3.4 Reasonably Foreseeable Misuse 9

3.5 Explanation of symbols and signal words 10

3.6 Liability 10

3.7 Residual risks 11

3.8 Skilled Persons 12

3.9 Notes for Resellers 12

4 Scope of delivery 12

5 Product 13

5.1 About Cascading 13

5.2 About the SMARTneo-2G 13

5.2.1 Control Box connections 13

5.2.2 Hand Control 13

6 Connecting the System 14

6.1 Safety 14

6.2 Dimensions 14

6.3 Assembly instructions 14

6.4 Specications for the Cascading System 14

6.5 Cascading System with two Actuators 15

6.5.1 Required Components 15

6.5.2 Connecting the Components 15

SMARTNEO-2G: CASCADING MANUAL // PAGE 7

6.6 Cascading System with three Actuators 16

6.6.1 Required Components 16

6.6.2 Connecting the Components 16

6.7 Cascading System with four Actuators 17

6.7.1 Required Components 17

6.7.2 Connecting the Components 17

7 Operation 18

7.1 Reference Drive 18

7.2 Factory Reset 18

7.2.1 With a Basic Hand Control 18

7.2.2 With a Comfort Hand Control 19

8 Troubleshooting 20

8.1 Lexicon 20

8.2 Possible Problems and their Solutions 20

9 Additional Information 21

9.1 Changing a Cascading System 21

9.1.1 Replacing a Control Box 21

9.1.2 Replacing an Actuator 21

9.1.3 Ungrouping a Cascading System 21

9.2 Maintenance 21

9.2.1 Disposal 21

SMARTNEO-2G: CASCADING MANUAL // PAGE 8

2 GENERAL INFORMATION

Documentation for SMARTneo-2G Cascading Systems consists of this Operating Manual and several other

documents. Read all documentation before assembling or operating the table system. Keep all documen-

tation for as long as the product is in your possession. Ensure that all documentation is provided to subse-

quent owners. Go to www.logicdata.net for more information and support. This Manual may change with-

out notice. The most recent version is available on our website.

2.1 OTHER APPLICABLE DOCUMENTS

This Operating Manual assumes that the reader has read the following documents:

• Datasheet and Operating Manual for the installed Actuator(s)

• Datasheet and Operating Manual for the installed User Interface (Hand Control or other)

• Datasheet and Operating Manual (if applicable) for any installed accessory products

• Datasheet and Operating Manual for the SMARTneo-2G

2.2 COPYRIGHT

© July 2019 by LOGICDATA Electronic und Software Entwicklungs GmbH. All rights reserved, except for

those listed in Chapter 1.3 Royalty-free use of images and text on page 5.

2.3 ROYALTY-FREE USE OF IMAGES AND TEXT

After purchase and full payment of the product, all text and images in Chapter 3, “Safety”, may be used free

of charge by the customer for 10 years after delivery. They should be used to prepare end user documenta-

tion for height-adjustable table systems. The license does not include logos, designs, and page layout ele-

ments belonging to LOGICDATA. The customer may make any necessary changes to the text and images to

adapt them for the purpose of end user documentation. Texts and images may not be sold in their current

state, and may not be published or sublicensed digitally. The transfer of this license to third parties without

permission from LOGICDATA is excluded. Full ownership and copyright of the text and graphics remain

with LOGICDATA. Texts and graphics are oered in their current state without warranty or promise of any

kind. Contact LOGICDATA to obtain text or images in an editable format ([e-mail]).

2.4 TRADEMARKS

Documentation may include the representation of registered trademarks of goods or services, as well as

information about copyright or other proprietary expertise of LOGICDATA or third parties. In all cases, all

rights remain exclusively with the respective copyright holder. LOGICDATA® is a registered trademark of

LOGICDATA Electronic & Software GmbH in the USA, the European Union, and other countries.

SMARTNEO-2G: CASCADING MANUAL // PAGE 9

3 SAFETY

3.1 TARGET AUDIENCE

This manual is intended for Skilled Persons only. Refer to Chapter 3.8, Skilled Persons on page 12 to ensure

that personnel meet all requirements.

3.2 GENERAL SAFETY REGULATIONS

In general, the following safety regulations and obligations apply when handling the product:

• Do not operate the Cascading System unless it is in a clean and perfect condition

• Do not remove, change, bridge, or bypass any protection, safety, or monitoring equipment

• Do not convert or modify any components without written approval from LOGICDATA

• In the event of malfunction or damage, any faulty components must be replaced immediately

• Unauthorized repairs are prohibited

• Do not attempt to replace hardware unless the system is in a de-energized state

• Only skilled persons are allowed to work on the Cascading System

• Ensure that national worker protection conditions and national safety and accident prevention

regulations are observed during operation of the system

3.3 INTENDED USE

The SMARTneo-2G is a Control Box for electrically Height-Adjustable Tables. It is intended for indoor use

only. The system may only be installed in compatible Height-Adjustable Tables and with LOGICDATA-

approved accessories, including those intended to enable Cascading functionality. Contact LOGICDATA for

further details. Use beyond or outside the intended use will void the product’s warranty. Please refer to the

Operating Manual of each product in the Table System to determine its individual intended use.

The installation site must be level, vibration-free, and free from contamination. It must be ensured that

there is no extraordinary exposure through dust, toxic or caustic gases and vapours, or through inadmissi-

ble heat exposure at the installation site.

3.4 REASONABLY FORESEEABLE MISUSE

Usage outside of the intended use of a Cascading System could lead to minor injuries, serious injuries, or

even death. Reasonably foreseeable misuse of the system includes, but does not extend to:

• Using the system as a climbing or lifting aid for people or animals

• Connecting unauthorized products to a Cascading System. If you are unsure as to whether a

product can be used with your system, contact LOGICDATA for further information

• Overloading the Table System

SMARTNEO-2G: CASCADING MANUAL // PAGE 10

3.5 EXPLANATION OF SYMBOLS AND SIGNAL WORDS

Safety notices contain both symbols and signal words. The signal word indicates the severity of the hazard.

DANGER

WARNING

CAUTION

NOTICE

NOTICE

INFO

INFO Indicates important tips for handling the product.

Indicates a hazardous situation which, if not avoided, will result in death or serious
injury.

Indicates a hazardous situation which, if not avoided, could result in death or serious
injury.

Indicates a hazardous situation which, if not avoided, could result in minor or moder­ate injury.

Indicates a situation which, if not avoided, could result in damage to the product
through electrostatic discharge (ESD).

Indicates a situation that will not lead to personal injury, but could lead to damage to
the device or the environment.

Indicates the protection class of the device: Protection Class III.
Protection Class III devices may only be connected to SELV or PELV power sources.

3.6 LIABILITY

LOGICDATA products comply with all currently applicable health and safety regulations. However, risk can

result from incorrect operation or misuse. LOGICDATA is not liable for damage or injury caused by:

• Improper product use

• Disregard of the documentation

• Unauthorized product alterations

• Improper work on and with the product

• Operation of damaged products

• Wear parts

• Improperly performed repairs

• Unauthorized changes to the operating parameters

• Disasters, external inuence, and force majeure

The information in this documentation describes the characteristics of the system without assurances.

Resellers assume responsibility for the LOGICDATA products installed in their applications. They must en-

sure their product complies with all relevant directives, standards and laws. LOGICDATA shall not be held

liable for any damage that is directly or indirectly caused by the delivery or use of this document. Resellers

must observe the relevant safety standards and guidelines for each product in the Table System.

SMARTNEO-2G: CASCADING MANUAL // PAGE 11

3.7 RESIDUAL RISKS

Residual risks are the risks that remain after all relevant safety standards have been complied with. These
have been evaluated in the form of a risk assessment. Residual risks associated with the connection and opera­tion of the Cascading System are listed in this Manual. The risks associated with the installation of other prod­ucts in the system, including the SMARTneo-2G, are detailed in the respective product’s Operating Manual.

See also Chapter 2.1. The symbols and signal words used in this Operating Manual are listed in Chapter 3.5.

WARNING Risk of death or serious injury through electric shocks

WARNING Risk of death or serious injury in explosive atmospheres

WARNING Moderate risk of serious injury through electric shocks

WARNING Moderate risk of serious injury through electric shocks

The products in the Cascading System are electrical devices. Basic safety precautions
must be taken at all times. Failure to observe electrical safety precautions may lead to

death or serious injury through electric shocks.

• Never open any product or its components

• Ensure that products are not connected to the mains during assembly

• Ensure that the SMARTneo-2G is supplied with the mains voltage specied on the
Type Plate

• Do not convert or modify any product in any way

• Do not place Cables on heated surfaces

• Do not immerse any components in liquid. Clean only with a dry, soft cloth

• Check all housings and cables for visible damage. Do not install or operate dam­aged products.

Operating the system in potentially explosive atmospheres may lead to death or serious
injury through explosions.

• Read the relevant directives to determine if an atmosphere is potentially explosive

• Do not operate the system in potentially explosive atmospheres

While cleaning or using the system, liquid intrusion may lead to serious injury through
electric shocks.

• Do not allow any components to become wet during cleaning

• Ensure components are placed away from areas where spillages are likely to occur

• Take care not to spill liquids onto or around the system

Inserting cables incorrectly may lead to death or serious injury through electric shocks.

• Ensure only LOGICDATA-approved products are connected to the SMARTneo-2G

• Do not insert incompatible cables into the SMARTneo-2G

• Do not attempt to force cables into the incorrect plug ports

CAUTION Risk of minor or moderate injury through unexpected movement

CAUTION Risk of minor or moderate injury through crushing

CAUTION Risk of minor or moderate injury through tripping

CAUTION

Exceeding the static or dynamic load limits of the Table System may cause unexpected
operation. This may lead to minor or moderate injury.

• Do not exceed load limits

If any Hand Control Key becomes stuck while the system is in motion, the system may
not stop properly. This may lead to minor or moderate injury through crushing.

• Disconnect the system immediately if any Hand Control Key becomes stuck

During the assembly process, you may have to step over Cables. Tripping over Cables
may lead to minor or moderate injury.

• Ensure that the assembly area is kept clear of unnecessary obstructions

• Be careful not to trip over Cables

T

his appliance can be used by children from 8 years and above and people with reduced
physical, sensory or mental capabilities or lack of experience and knowledge if they
have been given supervision or instruction concerning the use of the appliance in a safe
way and understand the hazards involved. Children must not play with the appliance.
Cleaning and maintenance by the user must not be performed by children, unless they
are over 8 years old and supervised

.

SMARTNEO-2G: CASCADING MANUAL // PAGE 12

3.8 SKILLED PERSONS

CAUTION Risk of injury through incorrect installation

Only Skilled Persons have the expertise to complete the installation process safely.
Installation by unskilled persons can lead to minor or moderate personal injury.

• Ensure that only Skilled Persons are allowed to complete the installation

• Ensure that persons with limited ability to react to danger do not take part in the

assembly process

The Cascading System may only be assembled by Skilled Persons. A Skilled Person is dened as someone
who:

• Is authorized for installation planning, installation, commissioning, or maintenance/servicing
of each product in the Table System

• Has read and understood the Cascading System documentation, as well as the documentation
relevant to the component products of the system

• Has the technical education, training, and/or experience to perceive risks and avoid hazards

• Has knowledge of the specialist standards applicable to the product

• Has the expertise to test, assess, and manage electrical and mechatronic products and systems
in accordance with the generally accepted standards and guidelines of electrical engineering
and furniture manufacturing

3.9 NOTES FOR RESELLERS

Resellers are companies that purchase LOGICDATA products for installation in their own products.

INFO

INFO

INFO

INFO

INFO

For reasons of EU conformity and product safety, Resellers should provide end users
with an Operating Manual in their native EU ocial language.

The Charter of the French Language (La charte de la langue française) or Bill 101
(Loi 101) guarantees the right of the population of Quebec to conduct business and
commercial activities in French. The bill applies to all products sold and used in Quebec.

For table systems that will be sold or used in Quebec, Resellers must provide all product­relevant texts in French. These include, but are not limited to:

• Operating Manuals

• All other product documentation, including datasheets

• Inscriptions on the product (such as labels), including those on product packaging

• Warranty certicates
The French inscription may be accompanied with a translation or translations, but no

inscription in another language may be given greater prominence than that in French.

Operating Manuals must include all the safety instructions that end users require to
handle the product safely. They must also include an instruction to always keep the
Operating Manual in the immediate vicinity of the product.

No unauthorized persons (young children, persons under the inuence of medications,
etc.) should be allowed to handle the product.

Resellers must perform a risk assessment on their product that covers residual hazards.
It must include measures to mitigate risk or reference the product's Operating Manual.

4 SCOPE OF DELIVERY

The scope of delivery for the Cascading System depends on the conguration chosen. See the “Required

Components” sub-chapter for your chosen conguration to see which components are necessary. The com­ponents supplied in each product’s package are outlined in the respective Operating Manuals.

SMARTNEO-2G: CASCADING MANUAL // PAGE 13

5 PRODUCT

5.1 ABOUT CASCADING

Cascading is the process of connecting two SMARTneo-2G Control Boxes together in order to control extra

Actuators. A maximum of 4 Actuators can be connected. Each Actuator must be of the same type.

In Cascading Systems, the two Control Boxes are connected by a Sync Cable (LOG-CBL-SMARTneo­SYNC-1000). The process of creating a Cascading System consists of two stages:

1. Connecting the components (Chapter 6.5 - 6-7)

2. Performing a Reference Drive (Chapter 7.1)

5.2 ABOUT THE SMARTNEO-2G

The SMARTneo-2G is a Control Box for height-adjustable tables. There are variants of the SMARTneo-2G for
specic domestic mains power supplies (e.g. EU or US). The exact variant is denoted by the product’s order

code. Consult the accompanying Datasheet to ensure that you have received the correct variant. The func­tions your SMARTneo-2G Control Box can full is also dependent on parameterization.

NOTICE

This Cascading Manual is only valid for the SMARTneo-2G (2nd generation). Consult your
product's Datasheet and Type Plate to ensure this is the correct Manual for your product.

5.2.1 CONTROL BOX CONNECTION POINTS

1 DC/Com Port (Sync Cable)

2 Motor Port 1 (M1)

3 Motor Port 2 (M2)

4 Hand Control Port (HC)

5 AC Input Port (Power Cable)

Fig. 2: Control Box Connection Points

1

2

3

5

4

5.2.2 HAND CONTROL

All instructions assume the reader has assembled a Table System that will be controlled by a Hand Control

with an UP Key and DOWN Key. If your Table System is operated by a dierent User Interface, consult that

product’s operating Manual for instructions on operating the Table System. The availability of some func-

tions depends on the Hand Control used. This section describes two variants:

• Comfort Hand Controls - These products have a digital display and can save Memory Positions

• Basic Hand Controls - These products have only an UP and DOWN key

Hand Control Keys are represented as follows for further description:

UP Key

DOWN Key

SAVE

1

2

3 4

SAVE Key

Memory Position Keys

SMARTNEO-2G: CASCADING MANUAL // PAGE 14

6 CONNECTING THE SYSTEM

The SMARTneo-2G can be used to create a variety of Table Systems. This Manual describes the connection
of table systems in which two Control Boxes will be connected.

This chapter describes the process of connecting the Cascading System’s components after they have been
mounted to the Height-Adjustable Table System. You must read the documentation for each part of the sys­tem (Actuator, User Interface, Control Box, etc.) for that product’s mounting instructions.

This Chapter outlines three common congurations for Cascading Systems. For further information con­cerning other cascading options for the SMARTneo-2gen, please contact LOGICDATA.

6.1 SAFETY

WARNING

WARNING

NOTICE

NOTICE

INFO

Moderate risk of death or serious injury through electric shocks

Connecting the system incorrectly can lead to serious injury through electric shocks.

• Ensure that the supplied voltage complies with the SMARTneo-2G's type plate

• Ensure all components are connected to the correct sockets

• Do not use unauthorized accessory parts or cables

• Disconnect the SMARTneo-2G from the power outlet before removing or connect­ing any components

• Connect the system to the Mains only after all other components (Actuators, addi­tional Control Boxes etc.) have been connected to the SMARTneo-2G

Moderate risk of death or serious injury through electric shocks

Using damaged products may lead to death or serious injury through electric shocks.

• Do not operate the Cascading System if you see housings or cables are damaged

Ensure proper ESD handling during assembly. Damage that can be attributed to electro­static discharge will void warranty claims.

This manual is applicable for Cascading Systems with the SMARTneo-2G Control Box.
SMARTneo-2G Control Boxes cannot be connected to any other type of Control Box.
Connecting incompatible Control Boxes may damage the Table System.

Perform a product risk assessment so that you can respond to potential residual haz­ards. Assembly instructions must be included in your end user Operating Manual

6.2 DIMENSIONS

The dimensions of each product in the Table System can be found in that product’s Datasheet.

6.3 ASSEMBLY INSTRUCTIONS

Assembly instructions for each product in the Table System can be found in that product’s Manual.

6.4 SPECIFICATIONS FOR THE CASCADING SYSTEM

Before connecting the Cascading System, make sure that the following requirements are met:

• Assembly has been completed safely and correctly for all components

• All Actuators are of the same type (e.g. SLIMdrive-660s or SLIMdrive-500)

• The Control Boxes are set to factory settings (Chapter 7.2 Factory Reset, page 18) or have
been correctly parameterized. Otherwise, a Factory Reset is required during setup.

• The voltage supply corresponds to the specications on the respective type plate

SMARTNEO-2G: CASCADING MANUAL // PAGE 15

6.5 CASCADING SYSTEM WITH TWO ACTUATORS

INFO

When a Hand Control is connected to a Cascading System for the rst time, the
Control Box it is connected to becomes the master. The other Control Box is the slave.
If you wish to change which Control Box is the master, a factory reset is required.

6.5.1 REQUIRED COMPONENTS

Quantity Component

1 Hand Control

2 SMARTneo-2G Control Boxes

2 Actuators. Only one type of Actuator (e.g. SLIMdrive-660s) can be used in each system

1 LOG-CBL-SMARTneo-SYNC-1000 Sync Cable

2 Power Cables

6.5.2 CONNECTING THE COMPONENTS

1. Connect the rst Actuator to a Control Box (M1)

2. Connect the second Actuator to the second Control Box (M1)

3. Connect the two Control Boxes using the Sync Cable (COM/DC)

4. Connect the Hand Control to a Control Box (HC)

5. Connect each Control Box to a separate Power Cable (AC)

6. Connect the Power Cables to the power source

▸ Each Control Box emits two short clicks

▸ (If a Comfort Hand Control is used) The display on the Hand Control shows

7. If the Control Boxes were not previously set to factory settings, perform a Factory Reset (Chapter

7.2, page 18)

OOO

1 2 3

4 5

6

3 4

1 2

3 4

SAVE

1 2

SAVE

SMARTNEO-2G: CASCADING MANUAL // PAGE 16

6.6 CASCADING SYSTEM WITH THREE ACTUATORS

INFO

When a Hand Control is connected to a Cascading System for the rst time, the
Control Box it is connected to becomes the master. The other Control Box is the slave.
If you wish to change which Control Box is the master, a factory reset is required.

6.6.1 REQUIRED COMPONENTS

Quantity Component

1 Hand Control

2 SMARTneo-2G Control Boxes

3 Actuators. Only one type of Actuator (e.g. SLIMdrive-660s) can be used in each system

1 LOG-CBL-SMARTneo-SYNC-1000 Sync Cable

2 Power Cables

6.6.2 CONNECTING THE COMPONENTS

1. Connect the rst two Actuators to a Control Box (M1 and M2)

2. Connect the third Actuator to the second Control Box (M1)

3. Connect the two Control Boxes using the Sync Cable (COM/DC)

4. Connect the Hand Control to a Control Box (HC)

5. Connect each Control Box to a separate Power Cable (AC)

6. Connect the Power Cables to the power source

▸ Each Control Box emits two short clicks

▸ (If a Comfort Hand Control is used) The display on the Hand Control shows

7. If the Control Boxes were not previously set to factory settings, perform a Factory Reset (Chapter

7.2, page 18)

OOO

1 2 3

4 5

6

1 2

3 4

SAVE

1 2

3 4

SAVE

SMARTNEO-2G: CASCADING MANUAL // PAGE 17

6.7 CASCADING SYSTEM WITH FOUR ACTUATORS

INFO

When a Hand Control is connected to a Cascading System for the rst time, the
Control Box it is connected to becomes the master. The other Control Box is the slave.
If you wish to change which Control Box is the master, a factory reset is required.

6.7.1 REQUIRED COMPONENTS

Quantity Component

1 Hand Control

2 SMARTneo-2G Control Boxes

4 Actuators. Only one type of Actuator (e.g. SLIMdrive-660s) can be used in each system

1 LOG-CBL-SMARTneo-SYNC-1000 Sync Cable

2 Power Cables

6.7.2 CONNECTING THE COMPONENTS

1. Connect the rst two Actuators to a Control Box (M1 and M2)

2. Connect the third and fourth Actuators to the second Control Box (M1 and M2)

3. Connect the two Control Boxes using the Sync Cable (COM/DC)

4. Connect the Hand Control to a Control Box (HC)

5. Connect each Control Box to a separate Power Cable (AC)

6. Connect the Power Cables to the power source

▸ Each Control Box emits two short clicks

▸ (If a Comfort Hand Control is used) The display on the Hand Control shows

7. If the Control Boxes were not previously set to factory settings, perform a Factory Reset (Chapter

7.2, page 18)

OOO

1 2 3

4 5

6

1 2

3 4

SAVE

1 2

3 4

SAVE

SMARTNEO-2G: CASCADING MANUAL // PAGE 18

7 OPERATION

CAUTION

CAUTION

This Chapter describes functions that are specic to the Cascading System. Operation Instructions applica-

ble for all Table Systems can be found in the manual for the SMARTneo-2G.

Risk of minor or moderate injury through uncontrolled movement

The table may not always stop exactly at the expected position. Failure to anticipate the
table's movements may lead to minor or moderate injury through crushing.

• Wait until the system has completely stopped before attempting to use the table

Risk of minor or moderate injury through unsecured objects

While the table moves up and down, unsecured objects may fall o the table and onto
body parts. This may lead to minor or moderate injury through crushing.

• Ensure loose objects are kept away from the edge of the table

• Do not leave unnecessary objects on the table during movement

7.1 REFERENCE DRIVE

NOTICE

A Reference Drive allows the Actuators to be retracted or extended to a parameterized reference length. A

Reference Drive must be performed after the Cascading System has been connected for the rst time.

o73

Ensure that all Actuators move in the same direction and adjust the height of the
desktop during the Reference Drive. Misalignment may damage the system.

Ensure that all components are connected correctly.

Press and hold the DOWN Key

▸ The Actuators start up at reduced speed
▸ The Control Box will click when the table top reaches its lowest position.
▸ (If a Comfort Hand Control is used) The display on the Hand Control shows the

parameterized position of the Actuators.

Wait for at least 3 seconds During this time, motor detection is completed and saved.

▸ The Reference Drive is complete

7.2 FACTORY RESET (S0 RESET)

With this function, you can reset the SMARTneo-2G to its factory settings. No Factory Reset is required

before setup. Factory Resets are required after changes in the setup of Cascading System and to reset the

Slave-Master hierachy in the system (e.g. if a previous Slave will become the new Master). Resetting the

Master Control Box in the Cascading System also resets the Slave. If the Control Boxes are already in Factory

Settings, no Factory Reset is needed.

7.2.1 USING A BASIC HAND CONTROL

Disconnect the Control Box from the mains.

While disconnected, press and hold the UP and DOWN Keys

Reconnect the Control Box. Hold the Keys until the Control Box clicks twice per second.

Release the UP and DOWN Keys

The SMARTneo-2G has now been reset to its factory settings. It is now in the same state
as it was during the rst start-up.

SMARTNEO-2G: CASCADING MANUAL // PAGE 19

7.2.2 USING A COMFORT HAND CONTROL

Press and hold the following Keys for 3 seconds:

1 2

• Memory Position Keys 1 and 2

• UP Key

S 4

S O

SAVE

INFO

INFO

The display shows S and a number (e.g. S 4)

Press the DOWN Key until the display shows S 0.

The display shows S 0.

Press the SAVE Key.

The SMARTneo-2G has now been reset to its factory settings. It is now in the same
state as it was during the rst start-up.

Resetting the Master Control Box in the system to factory settings will automatically
reset the Slave Control Box.

If you wish to reset a Slave Control Box separately from the master, you will need to do
so in Single Mode. To proceed:

• Disconnect all Control Boxes from the Mains and wait for 20-30 seconds

• Connect a Comfort Handset to the Slave

• Reconnect the Slave Control Box to the Mains

• Use the instructions above to carry out a Factory Reset

SMARTNEO-2G: CASCADING MANUAL // PAGE 20

8 TROUBLESHOOTING

8.1 LEXICON

Term Denition

Single Control Box A Control Box that is not parameterized for Cascading. It may only be operated as

an individual Control Box.

Cascading Cascading is a system that enables the synchronous operation of multiple Actua-

tors. Two Control Boxes are connected to each other for this purpose.

Master In the Cascading System, the master is the Control Box that was rst connected to

the Hand Control. Input via the Hand Control is only possible through the master.

Single Mode A Control Box setting for boxes that can be cascaded, but are only operated as an

individual Control Box.

Slave In a Cascading System, the slave is the Control Box connected to the master.

8.2 POSSIBLE PROBLEMS AND THEIR SOLUTIONS

Error code /
malfunction

E7O

E93

The Control Box does
not respond to inputs
via the Hand Control

For further information, or if you are experiencing problems that are not covered in this chapter, refer to the

operating manual of the Hand Control and the operating manual of the SMARTneo-2G Control Box.

Possible cause Solution

Actuator conguration
has been changed

Cascading errors Check all plug connections

The Control Box is not
dened as the master

The Control Box is
defective

Disconnect the Control Boxes from the power
supply for approx. 30 seconds

Reconnect the Control Boxes to the power supply

Perform a Reference Drive

Check all cables and replace defective ones if
necessary

Check Control Boxes and replace defective ones if
necessary

Disconnect the Hand Control from the Control Box

Reset the Control Box to factory settings,
see chapter 8 on page 18

Contact customer services

SMARTNEO-2G: CASCADING MANUAL // PAGE 21

9 ADDITIONAL INFORMATION

9.1 CHANGING A CASCADING SYSTEM

Before any changes to a Cascading System are made, ensure both Control Boxes have been disconnected

from the Power Source.

After changing a Cascading System, you may need to perform a Factory Reset. Go to Chapter 7.2 for further

instructions.

9.1.1 REPLACING A CONTROL BOX

To exchange Control Boxes in an existing Cascading System, proceed as follows:

1. Reset both Control Boxes to factory settings, see chapter 7.2. (Optional: Can also be performed

after reconnection).

2. Disconnect the Control Boxes from the power source

3. Use the instructions in Chapter 6 to connect the components to the new Control Box

9.1.2 REPLACING AN ACTUATOR

To replace Actuators in an existing Cascading System, proceed as follows:

1. Disconnect the unwanted Actuator from the Control Box

2. Connect the new Actuator to the Control Box

3. Perform a Reference Drive, see chapter 7.1

9.1.3 UNGROUPING A CASCADING SYSTEM

1. Reset the Control Boxes to factory settings, see chapter 7.2. (Optional: Can also be performed

after reconnection).

2. Disconnect the Control Boxes from the power supply

3. Disconnect the cables

9.2 MAINTENANCE

All components in the Cascading System are maintenance-free for their entire service lifetimes. If cleaning

of any product required, wipe its housing with a soft, dry cloth.

9.2.1 DISPOSAL

The SMARTneo-2G is an electrical and electronic device that must be disposed of separately

from household trash in accordance with the WEEE directive 2012/19/EU. Products of this

type are labelled with the symbol shown on the left.

Before disposing of materials and components, check their recyclability. Recycle all parts if

possible. Dispose of all materials and parts according local guidelines and regulations. Ensure

that the disposal is lastingly compatible for humans and nature.

LOGICDATA
Electronic & Software Entwicklungs GmbH

Wirtschaftspark 18
8530 Deutschlandsberg
Austria

LOGICDATA North America, Inc.

1525 Gezon Parkway SW, Suite C
Grand Rapids, MI 49509
USA

Phone: [phone]
Fax: [phone]
Email: o[e-mail]
Internet: http://www.logicdata.net

www.logicdata.net

Phone: [phone]
Email: o[e-mail]