LKM7000
Increased Safety, Increased Security, Increased Functionality.
INSTALLATION INSTRUCTIONS
90 minute re rating alone or
with Kaba Mas X09.
Not rated when used with a
S&G 2740 lock.
7000INST Copyright Lockmasters, Inc. 5/25/11
In A Single Motion, We’ll Change The Way
You Think About Security.
National Stock Number 5340-01-501-2828 US Patent #7,007,524,B2
1
LKM7000 Inside Base Plate Exploded View
Component Part No.
Inside Base Plate Complete w/ Screws & Hardware 700013WBA
Internal Access Control 700016
Handle Tube 700013S01
Extended Spindle Kit 700013S01EXT
Complete Wiring Harness 700013S45
Yoke 700013S09
Bolt Spring 700013S18
Slide Spring 700013S46
Trigger Spring 700013S19
LOCKBODY AND PARTS
LKM7000 EXPLODED VIEW
Not all items are eld retro-ttable.
2
7000INST Copyright Lockmasters, Inc. 5/25/11
LKM7000 Front Plate Exploded View
Component Part No.
Handle Screw 700012S13
Lock Washer for Handle Screw 700012S18
Intermediate Gear 700012S14
Hub Handle Half Gear 700012S01
Handle return Spring 700012S12
Outside Lever Handle 700012S11
Neoprene Handle Grip 7000HANDGRP
Complete Front Plate Assembly 700012WBA
Not all items are eld retro-ttable.
7000INST Copyright Lockmasters, Inc. 5/25/11
3
Read instructions thoroughly prior to installation
Record the Lock’s Serial Number prior to installation:
WARNING - Must read before installation
IT IS IMPERATIVE THAT THE DOOR REMAIN OPEN DURING INSTALLATION OF THE LKM7000.
If the door closes while the back cover is removed, the relockers will trigger resulting in a lockout.
Important Information
All seals and gaskets must be applied to the door frame PRIOR to installing a LockOne Series Lock.
Compression type sound seals are NOT RECOMMENDED when using a LockOne Series Lock.
DRILLING A HOLLOW DOOR
To avoid alignment issues you should NEVER drill a through hole in a hollow door. To ensure a level through hole, you should
drill through one side of the door then drill through the other side of the door.
4
7000INST Copyright Lockmasters, Inc. 5/25/11
Optional Products
STAND-OFF KIT for the LockOne Series Lock
We strongly recommend using a Stand-Off Kit, which prevents a hollow metal door
from compressing during installation of a LockOne Series Lock. Stand-Off Kits are
sold separately and available for 1 3/4” and 2” doors.
PART NUMBERS: 1 3/4” Door - LKM7000SOK1
2” Door - LKM7000SOK
INTERNAL HARDPLATE
PART NUMBER: LKM7000SMHP
DOOR COVERS
When retro-tting an existing door we recommend using a set of 12” x 18” door
covers, prior to installation. Finish is powder coat black.
PART NUMBER: LKM7000DCIO (set of 2)
Installation Aids
DOOR WEDGES
It’s a simple 3 oz. wedge of practically indestructible
lexan plastic designed to hold virtually any door at 900.
Interior or exterior, oversize, special purpose, even
pivoting glass doors.
PART NUMBER: LKMDWEDGE
7000INST Copyright Lockmasters, Inc. 5/25/11
5
LKM7000 Strikes
Strike 1
LKM01S
Strike 2
LKM02S
Strike 3
LKM03S
6
Strike No. 9
Strike 9
LKM09S
7000INST Copyright Lockmasters, Inc. 5/25/11
LKM7000 Main Components
L
C
I
M
K
E
N
F
B
P
D
O
H
G
J
A. Front Plate (FP)
B. Lever Handle
Q
R
A
C. Inside Base Plate (IBP)
D. Wire Routing Box
E. 1/4”-20x 2 1/2” Socket Head
Machine Screws (4)
F. 1/4” Phillips Head Thread Forming
Screws (4)
G. 1/4”-20x1 3/4” Socket Head Machine
Screw & Washer (1)
H. 1/4”-20x1 3/4” Flat Head Phillips
Machine Screws & Finishing
Washer (2)
I. Push & Pull Decal
J. Lever Handle Grip
K. Debur Stone
L. 3/32” & 3/16” Hex Head Wrenches
M. Liquid Thread Locker
N. Change Key Hole Plug
O. Filler Blocks (2)
P. Templates
Q. Installation Instructions
R. Operating Instructions
LKM7000 Installation - Tools Needed
Drill
Wire Cutters or Strippers
Snap Ring Pliers
File
Chisel
Hack Saw
Center Punch (Automatic)
10-24 Tap & Tap Handle
7000INST Copyright Lockmasters, Inc. 5/25/11
Hammer
Small Pocket Screwdriver
Phillips & Flat Screwdrivers
Level & Combination Square
Tape Measure
Vise
Masking & Double Sided Tape
Scissors & Exacto Knife
1/8” Drill Bit
3/16” Drill Bit
5/16” Drill Bit
3/8” Drill Bit
5/8” Wood Cutting Bit
5/8” Hole Saw
3/4” Wood Cutting Bit
3/4” Hole Saw
1 5/8” Wood Cutting Bit
1 5/8” Hole Saw
13/64” Drill Bit
#25 Drill Bit
Safety Goggles
Rubbing Alcohol
7
LKM7000 Strike Installation
For this application the LKM7000 is installed on a single hollow metal door with a #2 strike,
however the instructions apply to any strike. Please note Lockmasters has stainless
steel strikes exclusively for the LKM7000 family of locks.
Step 1 – Temporarily Installing the Strike
Step 1A – Position the center of the strike 43” on the door frame above the nished oor.
NOTE: The inside base plate should not extend beyond the edge of the door.
Step 1B – Mark the top and bottom position of the strike as well as the oversized
alignment hole in the center of the strike.
Tip: double stick tape the strike into
position to mark and punch.
1a - Strike - Center Hole 43” from nished oor.
1b - Strike - Mark the top & bottom of strike.
Step 2 – Center punch & drill alignment/center hole
Step 2a – Center punch and drill a pilot hole with a #25 drill bit. Use an 10-24 tap and
tap the center alignment hole. Attach the strike to the door frame with the 10-24x1” pan
head machine screw provided and tighten into the center hole only. (Figure 1)
(Figure 1) ALIGNMENT HOLE
Attach the strike to the door frame by installing
only 1 screw at this time into the center hole using
the truss head screw.
Tip: use an automatic center punch for more precise punching.
1b - Strike - Mark center hole.
2a - Strike - Center punch alignment/center hole.
2a - Strike - Tap alignment/center hole.2a - Strike - With a #25 bit drill a pilot hole.
Step 3 – Prepare the Installation Templates
Begin by selecting the template that matches the appropriate door handing for the
install. Templates are provided for both right and left hand doors. Before beginning the
installation you must cut out all the areas marked with a dashed line.
8
2a - Strike - Attach with 10-24x1” screw.
Template - Cut out all dashed line.
7000INST Copyright Lockmasters, Inc. 5/25/11
LKM7000 Installation
Step 4 – Position the Inside Base Plate Template
Close the door and align the Inside Base Plate template over the strike and level with
the indicated horizontal level line on the template. Make sure to keep equal clearance
around the strike. Attach the template to the door with masking tape. NOTE: If the
template hits the strike. You can either reposition the template or loosen the strike
screw and adjust the strike position and retighten the screw.
Step 5 – Position the Front Plate Template
Step 5A – Make a small mark on the door’s edge in line with the horizontal level line.
Step 5B – Use the combination square to transfer that level line around the edge of
the door.
Step 5C – Use the combination square to extend that level line across the front of
the door at least 9”. This establishes a horizontal level line from the back of the door
around to the front.
4 - Template - Center template & strike to allow
clearance.
5a - Template - Extending Inside Base Plate (IBP)
horizontal line to the edge of the door.
5b - Template - Extending Inside Base Plate (IBP)
horizontal line to the edge of the door.
NOTE - FOR BEVELED DOOR EDGE
If the door has a beveled edge, establish the high side of the bevel using the
combination square. If it has a bevel the square must be at against the door and
at against the high edge. You will see a gap between the door and the combination
square. (See Figure 2).
Figure 2 - Establishing the high side of a bevel edged door.
7000INST Copyright Lockmasters, Inc. 5/25/11
5c - Template - Extending level line around to the
front of the door.
9
LKM7000 Installation
Position the Front Plate Template continued
Step 5D – Once the high side of a beveled edge door is established. Loosen the
combination square and position the rule to the vertical plumb line on the inside base
plate template and tighten the combination square. (Figure 3).
(Figure 3) ESTABLISH VERTICAL PLUMB LINE
On the IBP template position the combination
square against the vertical plumb line.
5d - Template - Determining distance of IBP
vertical plumb line.
5e - Template - Marking vertical plumb line on the
front side of the door
Step 5E – Transfer the vertical level line by ipping the combination square to the other
side of the door and make two marks at the end of the rule approximately 6” apart.
Step 5F – With the rule positioned on the marks draw the vertical plumb line at least 9”.
This establishes a vertical plumb line on the outside of the door.
Step 6 – Position the front plate template.
Align the vertical and horizontal lines printed on the template where they intersect with
the vertical and horizontal lines drawn on the door. Tape the template to the door with
masking tape. (Figure 4)
(Figure 4) POSITION FRONT
PLATE TEMPLATE
Align front plate template to
the vertical and horizontal lines
marked on the front of the door.
5f - Template - Mark vertical plumb line on the
front of the door.
6 - Template - Front of door vertical and hortizontal
lines marked.
10
6 - Template - Taping front plate template to vertical and horizontal plumb lines.
7000INST Copyright Lockmasters, Inc. 5/25/11
LKM7000 Installation
Step 7 – Center punch and label holes
Step 7A - Begin on the Inside Base Plate Template and use your hammer and center
punch to mark “punch” the following: (1) A, clutch hole: (6) B, front plate attaching
holes; (4) C, Inside Base Plate attaching holes; and (1) F, optional Wire Entry Hole
- Punch only if you are utilizing one or more of the following: 12 or 24v dc Access
Control input, Monitoring the position of the Combination Lock Bolt, and Monitoring
the position of the LKM7000 Dead Bolt/Request to Exit (REX). Potentially (12) holes.
Step 7B – Re-tape the template above the punched holes for easy reference. Label
all the hole diameters from the template to the corresponding the holes on the door for
reference during drilling.
Tip: When labeling the holes note the hole
size next to the hole.
7a - Center punch all applicable holes on IBP
template
Step 7C – Move to the front plate template, use your center punch to mark “punch” the
following (1) D, spindle hole and (6) E, front plate attaching holes.
Step 7D - Re-tape the template above the punched holes for easy reference. Label all
the hole diameters from the template to the corresponding the holes on the door for
reference during drilling.
HOLLOW DOOR NOTICE: Due to alignment issues, you should
NEVER drill a through hole in a hollow door. To ensure a level
through hole, you should drill through one side of the door then
drill through the other side of the door.
7b - Move template and label holes for easy
reference during drilling.
7c - Center punch all applicable holes on Front
Plate template
7000INST Copyright Lockmasters, Inc. 5/25/11
7d - Move template and label holes for easy
reference during drilling.
11
LKM7000 Installation
Step 8 – Drill Pilot Holes
Step 8A - We recommend using a 1/8” drill bit to pilot drill all center punched holes.
Step 9 – Drill the Inside Base Plate side of the door
Step 9A - Drill the (1) A, clutch hole – use a 1-5/8” hole saw, drill through the outer skin
of the door only. IMPORTANT NOTE: for solid wood doors - use a 1-5/8” wood cutting
bit. Use masking tape on the bit to mark a depth of 1-1/16”.
Step 9B – Drill the (6) B, Front Plate attaching holes – use a 5/16” drill bit, drill through
the outer skin of the door only. IMPORTANT NOTE: Solid wood doors - use a 5/16” wood
cutting bit. Use masking tape on the bit to mark a depth of 1-1/2”.
8a- Drilling pilot holes on both sides of the door.
Step 9C – Drill the (4) C, Inside Base Plate attaching holes – use a 13/64”drill bit, drill
through the outer skin of the door only. Please note, this drill bit dimension is larger then
specied on the template for ease of threading screws into hollow metal. IMPORTANT
NOTE: Solid wood doors - use a 3/16” drill bit. Use masking tape on the bit to mark a
depth of 1”.
Step 9D – OPTIONAL (1) F, Wire Entry hole – use a 5/16” drill bit, drill through the outer
skin of the door into the internal raceway. This applies to solid wood doors as well.
Step 10 – Drill the Front Plate Side of the door
Step 10A – Drill the (1) D, Spindle hole – use a ¾” hole saw, drill through the outer skin
of the door only. IMPORTANT NOTE: Solid wood doors - use a ¾” wood cutting bit and
drill until it connects to the (A) Clutch hole.
Step 10B – Drill the (6) E, Front Plate attaching holes – use a 5/8” hole saw, drill through
the outer skin only. IMPORTANT NOTE: Solid wood doors – use a 5/8” wood cutting bit
and drill to a depth of at least 9/16” and connect to the previously drilled 5/16”(B) Front
Plate attaching holes.
9 a-d - Drilling all the holes on IBP side of the
door.
9 a-d - IBP holes drilled
12
10 a-b - FP holes drilled
7000INST Copyright Lockmasters, Inc. 5/25/11
LKM7000 Installation
Step 11 – Prep all drilled holes
Step 11A - Use the debur stone to debur all drilled holes.
Step 11B - Pre-thread all (4) C Inside Base Plate attaching holes – using one of the
Phillips head thread forming screws (F). A #2 square drive bit works well with the
screws.
11a - Debur all drilled holes
11b - Pre-thread all (4) C holes.
Step 12 – Attach the Lever Handle to the Front Plate
Step 12A – Attach the lever handle correctly depending on the direction of the door
swing. The handle will always point toward the hinge side of the door. (Figure 5)
(Figure 5) DIRECTION OF THE LEVER HANDLE
The handle will always point toward the hinge side of the door.
Step 12B – Place the split washer (G) onto the ¼”-20x1 ¾” socket head machine
screw (G) insert through the back of the Front Plate and thread it into the lever handle.
Step 12C – Secure the screw tightly using the 3/16” T-Handle hex wrench.
12a - Place lever handle on front plate.
12b- Place split washer & screw into front plate
into lever handle
7000INST Copyright Lockmasters, Inc. 5/25/11
12c - Secure the screw
13
LKM7000 Installation
IF STANDOFF KIT IS BEING USED - INSTALL NOW
Stand-offs are used to prevent a hollow metal door from compressing during installation.
The kit is applied to the backside of the Front Plate.
Take the (6) threaded set screws that come in the Stand-off kit and thread them into the
backside of Front Plate.
Then thread the (6) Stand-off sleeves onto the exposed threads of the set screws until
making contact with the backside of the Front Plate.
Stand-off Kit Install - thread set screws into
backside of front plate.
Stand-off Kit Install - thread sleeves onto set
screws
Stand-off Kits - available for 1 3/4” & 2” doors. This
install was on an 1 3/4” door
Step 13 – Attach the Front Plate to the door
Step 13A – On the front side of the door, seat the Front Plate into the (6) counter-bored
E holes until ush and square with the door. Hold into position.
Tip: To hold the Front Plate in position apply a piece of
double stick tape to the back. Make sure not to cover gears or
spindle holes.
Stand-off Kit Installed
13a - Seat the front plate in the (6) counter-bored
E holes until ush against the door
14
13a - Front plate in position.
7000INST Copyright Lockmasters, Inc. 5/25/11
LKM7000 Installation
Attach the Front Plate to the door continued
Step 13B – Move to the Inside Base Plate side of the door to
secure the lower portion of the Front Plate. Place a nishing
washer (H) on each of the (2) ¼”-20x2” at head Phillips screws
(H) and insert into the (2) lower (B) holes. Tighten to a snug t.
STANDOFF KIT OPTION – if the Stand-off kit is installed
use the (2) shorter ¼-20 at head Phillips screws supplied
with the Stand-Off Kit instead of the longer (H) screws.
Step 14 – Remove the Inside Base Plate cover
Step 14A – Use the 3/32” T-Handle hex wrench and remove all (4) 8-32x3/8” socket
head button screws.
Step 14B – Retract the bolt by depressing and holding the exit handle.
Step 14C - With a athead pocket screwdriver insert under the cover, behind the
handle and rotate the screwdriver. The cover will release. Tilt the cover and slide
through the handle to remove.
13b - Move to IBP side and secure the bottom of
the Front Plate.
14a - Remove the (4) 8-32x3/8” socket head button screws from the IBP cover.
14b - Press and hold the exit handle to retract
the bolt.
14c - Take a athead pocket screwdriver and
insert under the cover, behind the handle and
rotate.
DOOR WARNING – It is imperative that the door remains open during
installation of the LKM7000. If the door closes and latches while the
back cover is removed the relockers will trigger into a lock-out.
Step 15 – Measure the Spindle Tube
Step 15A – On the inside of the door seat the
Inside Base Plate with the spindle tube going
through the A hole until ush against the door
and hold in position.
Step 15B – Move to the front side of the door and
mark the spindle tube ush with the Front Plate or
count the number of exposed grooves on the
spindle tube. Remove the Inside Base Plate in
order to remove the spindle tube.
7000INST Copyright Lockmasters, Inc. 5/25/11
15a- Insert IBP Spindle thru the A hole.
14c - Insert a athead screwdriver under the
cover, behind the handle and rotate. The cover
will release. Tilt the cover and remove.
15b - Mark the spindle ush with the Front Plate.
15
LKM7000 Installation
Step 16 – Remove & Cut Spindle Tube to Correct Length
Step 16A – Use your snap ring pliers to remove the internal spindle tube retaining ring.
Step 16B – Remove the spindle tube from the Inside Base Plate by pulling the spindle
tube through the Inside Base Plate then remove the remaining external spindle tube
retaining ring. Both spindle tube retaining rings need to be removed to ensure they are
not damaged.
NOTE – Do not cut or grind the spindle tube
with the spindle tube attached to the Inside
Base Plate. Grit and dusk will collect on the
internal lubricant.
16a - Remove the internal & outer spindle retaining rings.
16b - Remove the spindle from the IBP.
Step 16C - Place the end of the spindle tube that will be discarded into a vise and tighten.
DO NOT OVERTIGHTEN, THIS CAN CAUSE DAMAGE TO THE SPINDLE TUBE AND
INTERFERE WITH THE OPERATION OF THE LOCK.
Step 16D – Use a hacksaw to cut the spindle tube (2) grooves below the mark or
counted depth. This is done so the spindle tube is ush with the front plate once all
the screws are tightened.
NOTE: Make sure to debur and clear all metal
shavings from the spindle tube use a le
and debur stone.
16b - With snap ring pliers remove the outer
spindle tube retaining ring from the spindle.
16c - Place the end of the spindle tube to be
discarded into a vise and tighten.
Step 16E– Re-attach the external spindle tube retaining ring and re-insert the spindle
tube into the Inside Base Plate, make sure the grooves on the spindle tube align with
the tabs on the clutch cam and re-attach the internal spindle tube retaining ring with the
snap ring pliers.
Clutch Cam Tabs
16
16d - Use a hacksaw to cut the spindle tube (2)
grooves below the mark or counted depth.
16e - Re-attaching spindle
7000INST Copyright Lockmasters, Inc. 5/25/11
LKM7000 Installation
Step 17 – Use of Filler Blocks
Step 17A – Insert the applicable ller block into the inside base plate before installation.
Option 1 – If you are not utilizing Access Control or monitoring the bolt sensors, push
the wire into the inside base plate. Insert the SOLID ller block (O).
Option 2 – If using external conduit on the secure side of the door, insert the NOTCHED
Filler Block (O). Feed the Access Control & Bolt Sensors Wiring through the conduit
and make connections (See Wiring diagram on page 19).
NOTE: Position the conduit snuggly against the notched ller block. DO NOT insert
conduit directly into the inside base plate. It will interfere with bolt retraction.
17a - Inserting the correct ller block into the IBP.
This installation used external conduit so the
notched ller block was needed - as described in
Option 2.
Option 3 – If the door is prepped with an internal raceway and the optional F, wire entry
hole has been drilled use the Wire Routing Box (D) to conceal the Access Control &
Bolt Sensors Wiring. As it needs to be routed outside of the inside base plate in order
to enter the raceway.
Correct position of the conduit against IBP.
Option 3 - Internal raceway option.
7000INST Copyright Lockmasters, Inc. 5/25/11
17
LKM7000 Installation
Step 18 – Secure the Inside Base Plate to the door
IF HARDPLATE IS BEING USED - INSTALL NOW
Align the hard plate to the backside of Inside Base Plate and secure with double-sided
tape. Secure by inserting (2) of the metal thread forming screws (F) into the base plate
holes (C) to hold the hard plate in position while securing the Inside Base Plate to the
door (See Figure 6).
Step 18A – To ensure vibration does not loosen the screws over time, we provide a
pack of Liquid Thread Locker (M) for use on the (4) ¼-20x2 ½” socket head machine
screws (E) that are used to secure the Front Plate. Simply place a few drops of the
liquid onto the threads prior to use.
Step 18B – On the Inside Base Plate side of the door, permanently attach the (4)
¼-20x2 ½” (E) screws. These (4) screws will go into the upper 4 (B) holes. (See
photo). Snug only. After all (4) screws are inserted tighten the screws into the lock.
STAND-OFF KIT OPTION – if Stand-off Kit is installed use the (4) shorter ¼-20 socket
head machine screws supplied in the Stand-off Kit, instead of the longer (E) screws.
Step 18C – Remove (2) (H) Phillips heads screws that were previously installed in step
13b. Apply thread locker and re-install.
IF hardplate is used.
18a - Prepping IBP attaching screws with liquid
thread locker (provided).
Step 18D – Install the (4) (F) ¼” Phillips head thread forming screws into (4) C holes.
HARDPLATE OPTION – If hardplate was installed install the (2) remaining (F)
¼” Phillips head thread forming screws into (2) C holes.
18b - Attaching IBP to the door.
18c - Remove and apply liquid thread locker to
pre-installed screws holding the front plate into
position and re-install.
(Figure 6) - HARDPLATE ALIGNMENT IF USED.
Use double-sided tape and align the hardplate with the IBP.
18
18d - Secure the front plate with the remaining
screws through the IBP.
7000INST Copyright Lockmasters, Inc. 5/25/11
LKM7000 Installation
OPTIONAL
Step 19 – Solenoid Activation ACCESS CONTROL
Step 19A – Access Control Integration
The LKM7000 is shipped with an internal solenoid requiring 24v dc to retract the solenoid
pin. OPTIONAL - In order to use a 12v dc access control unit you’ll need to peel back
the blue heat shrink material away and cut the RESISTOR out of the circuit. (See Photo
right)
RESISTOR
Step 19B – When an Access Control system is being used in conjunction with the
LKM7000 it will be necessary to release the Access Control Solenoid Plugger. This
is done by removing the thumb screw located on the top of the Access Control Block.
(See Figure 7 for the location of the Access Control Block.)
NOTE: The solenoid activation screw SHOULD NOT be removed until the Access
Control Unit has been completely installed. If the screw is removed without the
Access Control System online and the door closes an immediate lock-out will
occur.
OPTIONAL - Removing the RESISTOR to use
12v dc access control
19a - Make the wire connections for the access
control.
(Figure 7) - SOLENOID ACTIVATION SCREW
NOTE: This solenoid is NOT designed for continuous duty.
Solenoid Specications
12 or 24v dc minimum amperage 199 miliamps
19b - Locate the Solenoid Activation Screw
located in the IBP and remove to release the
Access Control Solenoid Plugger.
19b - Close Up
7000INST Copyright Lockmasters, Inc. 5/25/11
19
LKM7000 Installation
Step 19C – Combination Lock Sensor & LKM7000 Deadbolt
Sensor/REX
The combination lock bolt sensor monitors the extension and retraction of the
combination lock bolt. The LKM7000 Deadbolt Sensor/REX can be used to monitor
the LKM7000 Deadbolt . This can also be used as a Request to Exit switch to shunt
an alarm system. (See Figure 9 - Wire Diagram)
Blue Wire
Normally Open
Yellow Wire
Normally Closed
(Figure 9) WIRE DIAGRAM
The bolt position switch can be used as
an option in order to monitor the position of the combination lock bolt and the
lock bolt of the LKM7000.
White Wire
Common
Deadbolt
Sensor Switch
REQUEST TO EXIT (REX)
Combination
Lock Bolt
Orange Wire
Sensor Switch
Common
Green Wire
Brown Wire
Normally Closed
Step 20 – Remove all of the white protective lm from the Front
Plate.
Step 21 – Install the lever handle grip. Lubricate the lever handle
with liquid soap and with the widest end rst slide the foam grip
onto the handle.
20 - Remove all white protective lm from front
plate (2 pieces).
20
21 - Remove all white protective lm from
front plate (2 pieces).
7000INST Copyright Lockmasters, Inc. 5/25/11
LKM7000 Installation
Step 22 - Install the Combination Lock
Step 22a - Remove Warning Label
Remove the internal warning label in the Inside Base Plate.
Step 22b - When integrating a combination lock package with the LKM7000 follow the
lock manufacturer’s instructions to install properly.
Step 23 – Re-attach the Inside Base Plate Cover
Step 23A – Insert the Change Key Hole Plug (N) into the Change Key Hole. If the plug
is loose, expand the metal tabs.
22a - Remove warning label from IBP.
22 - Lock body installed inside the LKM7000 IBP
Step 23B – Guide the Inside Base Plate Cover through the handle and align the screw
holes.
Step 23C – Reinstall and secure the cover with (4) 8-32 x 3/8” socket head button screws.
Step 23D – Clean the surface of the handle with rubbing alcohol to ensure good label
adhesion.
Step 23 E - Place the push or pull decal
on the inside base plate handle depending
on the swing of the door.
23b - Guide IBP cover through the handle and
align the screw holes.
23a - Insert Change Key Hole Plug into the
Change Key Hole on the IBP cover.
23c - Secure IPB cover with (4) 8-32 x 3/8” socket
head button screws.
7000INST Copyright Lockmasters, Inc. 5/25/11
23d - Clean the surface of the IBP handle with rubbing alcohol.
23e - Place the applicable “Push” or “Pull” label on
the IBP handle.
21
LKM7000 Installation
Step 24 - Strike Adjustment
Step 24A – Close the door to ensure proper function. Make sure that no part of the
Inside Base Plate is rubbing the strike. Now is the time to make adjustments to the
strike if necessary. Minor adjustments can be made to the strike by either:
1. Loosen the center alignment screw.
2. Add paper shims provided with the strike.
3. File the adjustment tabs cast into the strike.
Once the strike is correctly aligned with the Inside Base Plate, tighten the alignment
screw.
Step 24B – Secure the Strike. Center punch the (4) remaining strike screw holes.
Step 24C - Use a #25 drill bit to drill the pilot holes.
Step 24D - Use an 10-24 tap and tap the remaining (4) holes.
Step 24E - Attach the strike to the door frame with the (4) 10-24x1” screws provided
and tighten.
24a - Close the door and check strike align.
24c - Use a #25 drill bit to drill pilot holes.
24b - Center punch the (4) remaining strike screw
holes.
24d - Use a 10-24 tap and tap the remaining (4)
holes.
22
24e - Attach the strike to the door frame Strike Attached.
7000INST Copyright Lockmasters, Inc. 5/25/11
LKM7000 Installation
Final Step - Test the Lock
After completing the installation, please read the enclosed operation instructions and
test the functionality of the combination lock, access control, LKM7000 and the door.
Test the LKM7000
7000INST Copyright Lockmasters, Inc. 5/25/11
23
Limited Liability Product Warranty Information
Lockmasters, Inc. warrants to the original retail purchaser for a period of one (1) year from the purchase date of the product
that the product shall be free of defects in the materials and workmanship, provided there is compliance with all installation,
operating and maintenance instructions provided by Lockmasters, Inc. and provided further, that the product has been subject to
normal use without any misuse, negligence, or the occurrence of any accidental damaging. “Product” as used in this warranty
refers to the Lock/OneTM Series Lock, not the installed combination lock.
This limited warranty is in lieu of all other warranties or conditions expressed or implied by law and/or custom.
In no event shall Lockmasters, Inc. liability exceed the original cost of the product.
Lockmasters, Inc. makes no other warranty with respect to the product, expressed or implied, including without limitation any
warranty as to suitability of the product for any particular purpose or use of the merchantability thereof and shall not be liable for
any loss or damage sustained through burglary, theft, robbery, re or other hazard.
In the event of a defect in the materials or workmanship covered by this warranty, the purchaser shall return, at purchaser’s
expense, the product to Lockmasters, Inc. The purchaser’s sole remedy shall be the repair or replacement of the product and
under no circumstances shall Lockmasters, Inc. be liable to the purchaser or any other for any consequential, incidental, economic, direct or indirect, general or special damages arising out of any breach of warranty.
This warranty and remedies set forth above are exclusive and in lieu of all others, oral or written, expressed or implied. No
dealer, distributor, agent or employee is authorized to make any modication or addition to this warranty.
Some states do not allow the exclusion or limitation or implied warranties or limitation of liability incidental for consequential
damages, so the above limitation or exclusions may not apply to you.
24
7000INST Copyright Lockmasters, Inc. 5/25/11
Loading...