LM Technologies LM400 Users Manual

LM-400

Page Number : 1 of 6

Bluetooth Module - Part Code LM-400

Top view Bottom view
Contents:

1. Device Overall Description

2. Bluetooth

-Features

-Speci cation Compliance

-Bluetooth Block Diagram

-Modulation Methods

- Power Consumption

- RF Characteristics

3. Pinout and nition

4. Mechanical Dimension

Side view

Device Overall Description

The BTM400 is designed to provide Bluetooth2.0 + EDR function on a small form factor. The Bluetooth function

is based on CSR BlueCore4-Ext Bluetooth System, which implements the full speed class 1 Bluetooth operations

with full 7 slave piconet support. The interface of BTM400 to host system is UART.

Bluetooth

Features

-CSR BlueCore4

-Bluetooth 2.0 + EDR support

-Full Speed Class 1 Bluetooth operation with full 7 slave piconet support

-Single onboard Antenna connector support (Optional)

-Chip antenna on board

Bluetooth Block Diagram

BC04

Chip Antenna
Or
RF I-PEX
Connector

Modulation Methods

FHSS ( Frequency Hopping Spread Spectrum ) defined in Bluetooth Specification.

Basic Data Rate

Enhanced Data Rate

Class1

Module

Data Rate Modulation scheme

1 Mbps GFSK

2Mbps π/4 – DQPSK

3Mbps 8DPSK

H/W Flow
Control

UART

VDD

Host
Pin
header

LM-400

Page Number : 2 of 6

0121 270 6232 | www.lm-technologies.com | [email protected]

LM-400

Page Number : 3 of 6

0121 270 6232 | www.lm-technologies.com | [email protected]

Bluetooth Power Consumption

Absolute Maximum Ratings

Parameter Min. Max. Unit

58+ 04- erutarepmeT egarotS

Other Pin Voltage Vss-0.4 VDD+0.4 DCV
Recommended Operating Conditions

Parameter Min. Max. Unit

07+ 01- erutarepmeT

General Electrical Specification

Parameter Description Min. Typ. Max. Unit

RF Output Power Measured in 50ohm 15 16.5 18 dBm

Load Impedance No abnormal Oscillation 5:1
Input Low Voltage RESET,UART,GPIO,PCM -0.30 - 0.80 DCV
Input High Voltage RESET,UART,GPIO,PCM 0.7VDD - VDD+0.3 DCV

Output Low Voltage UART,GPIO,PCM - - 0.40 DCV
Output High Voltage UART,GPIO,PCM VDD-0.4 - - DCV

Average Current Consumption Receive DM1 114 mA

℃

VCD 6.3 7.2 )DDV(egatloV ylppuS
VCD 3.3 0.3 )CCVP(egatloV ylppuS

℃

VCD 6.3 0.3 TRAU rof egatloV ylppuS
VCD 6.3 0.3 BSU rof egatloV ylppuS

zHG 084.2 204.2 ycneuqerF reirraC

mBd 68- 88- - ytivitisnes XR

Radio Characteristics - Basic Data Rate

Transmitter , VDD = 3.3V Temperature =+20°C

ycneuqerF

Min. Typ. Max. Bluetooth

(GHz)

Maximum RF transmit power

π/4 DQPSK
Maximum carrier frequency stability w
π/4 DQPSK
Maximum carrier frequency stability w
π/4 DQPSK
Maximum carrier frequency stability | w
8 DPSK

Maximum carrier frequency stability w
8 DPSK
Maximum carrier frequency stability w

(note)

2.480 - 7 -

- 2 -

0

- 6 -

i

- 8 -

+ wi |

0

- 2 -

0

- 6 -

i

Unit

Specification

mBd - 6 - 204.2

-6 to +20

<

±10 for all blocks

<

±75 for all

packets

<

±75 for all blocks

<

±10 for all blocks

<

±75 for all

packets

- 8 - KSPD 8

<

±75 for all blocks

mBd - 6 - 144.2

dBm

Bd 1+ ot 4- - 6.1- - rewop timsnart evitaleR

kHz

kHz

kHz

kHz

kHz

kHz

Maximum carrier frequency stability | w0 + wi |
π/4 DQPSK
Modulation Accuracy

8 DPSK
Modulation Accuracy

RMS DVEM -

99% DEVM ­Peak DEVM ­RMS DVEM -

99% DEVM ­Peak DEVM -

F>F0+3 MHz

- <-50 -

7

13
19

7

13
17

F<F0-3 MHz - <-50 ­F=F0-3 MHz - -46 -

In-band spurious emissions

F=F0-2 MHz - -34 ­F=F0-1 MHz - -35 ­F=F0+1 MHz - -35 ­F=F0+2 MHz - -31 ­F=F

+3 MHz - -33 -

0

EDR Differential Phase Encoding No

Errors

Receiver , VDD = 3.3V Temperature =+20°C

Sensitivity at 0.1% BER

Maximum received signal level
at 0.1% BER

C/I co-channel at 0.1% BER

Adjacent channel selectivity C/I

+1 MHz

F=F

0

Adjacent channel selectivity C/I

-1 MHz

F=F

0

Adjacent channel selectivity C/I

+2 MHz

F=F

0

Adjacent channel selectivity C/I

-2 MHz

F=F

0

Adjacent channel selectivity C/I

+3 MHz

F=F

0

Adjacent channel selectivity C/I
F=F

-5 MHz

0

F0= 2405, 2441, 2477 MHz
Adjacent channel selectivity C/I
F=F

image

π/4 DQPSK
8 DPSK - -78 ­π/4 DQPSK
8 DPSK - -10 ­π/4 DQPSK
8 DPSK - 19 ­π/4 DQPSK
8 DPSK - -5 ­π/4 DQPSK
8 DPSK - -5 ­π/4 DQPSK
8 DPSK - -40 ­π/4 DQPSK
8 DPSK - -20 ­π/4 DQPSK
8 DPSK - -45 ­π/4 DQPSK
8 DPSK - -45 -

π/4 DQPSK
8 DPSK -15

- -87 -

- -8 -

- 10 -

- -10 -

- -11 -

- -40 -

- -23 -

- -45 -

- -45 -

-20

- < 20 %

- < 30 %

- <

35 %

- < 13 %

- < 20 %

- <

25 %

< -40
<

-40

<

-40

<

-20

<

-26

<

-26

<

-20

<

-40

dBm
dBm
dBm
dBm
dBm
dBm
dBm
dBm

> 99 %

htooteulB .xaM .pyT.niM noitaludoM

Unit

Specification

< -70

-70

<
> -20
>

-20

< +13

+21

<

< 0

+5

<

< 0

<

+5

< -30

-25

<
< -20

-13

<
< -40
<

-33

< -40
<

-33

< -7

<

0

dBm
dBm
dBm
dBm

dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB

dB
dB

Note :

Measurement made using a PO WER_TABLE entery of TX_PRE 80, INT PA63, EXT PA255. This ensures that the

Bluetooth requirements for ACP and those defined by the FCC and ETSI are satisfied over the operating

temp erature rang of -5Ð to + 45Ð . Although the design is capable of generating in excess of + 18dBm,

regulatory compliance over the full temperature range of -5Ð to + 45Ð will not be satisfied if the transmit power

approaches this value.

LM-400

Page Number : 4 of 6

0121 270 6232 | www.lm-technologies.com | [email protected]

Part Number LM-400

Page Number : 5 of 6

0121 270 6232 | www.lm-technologies.com | [email protected]

Radio Characteristics – Enhanced Data Rate

Transmitter , VDD = 3.3V Temperature =+20°C

ycneuqerF

Min. Typ. Max. Bluetooth

(GHz)

Maximum RF transmit power

π/4 DQPSK
Maximum carrier frequency stability w
π/4 DQPSK
Maximum carrier frequency stability w
π/4 DQPSK
Maximum carrier frequency stability | w
8 DPSK

Maximum carrier frequency stability w
8 DPSK
Maximum carrier frequency stability w

8 DPSK
Maximum carrier frequency stability | w
π/4 DQPSK

Modulation Accuracy

8 DPSK
Modulation Accuracy

In-band spurious emissions

EDR Differential Phase Encoding No

Receiver , VDD = 3.3V Temperature =+20°C

Sensitivity at 0.1% BER

Maximum received signal level
at 0.1% BER

C/I co-channel at 0.1% BER

Adjacent channel selectivity C/I

+1 MHz

F=F

0

(note)

2.480 - 7 -

- 2 -

0

- 6 -

i

- 8 -

+ wi |

0

- 2 -

0

- 6 -

i

- 8 -

+ wi |

0

RMS DVEM -

99% DEVM ­Peak DEVM ­RMS DVEM -

99% DEVM ­Peak DEVM -

F>F0+3 MHz

- <-50 -

7

13
19

7

13
17

F<F0-3 MHz - <-50 ­F=F0-3 MHz - -46 ­F=F0-2 MHz - -34 ­F=F0-1 MHz - -35 ­F=F0+1 MHz - -35 ­F=F0+2 MHz - -31 -

+3 MHz - -33 -

F=F

0

Errors

π/4 DQPSK

- -87 -

8 DPSK - -78 ­π/4 DQPSK

- -8 -

8 DPSK - -10 ­π/4 DQPSK

- 10 -

8 DPSK - 19 ­π/4 DQPSK

- -10 -

8 DPSK - -5 -

Unit

Specification

-6 to +20
dBm

<

±10 for all blocks

<

±75 for all

kHz

kHz

packets

<

±75 for all blocks

<

±10 for all blocks

<

±75 for all

kHz

kHz

kHz

packets

<

±75 for all blocks

kHz

- < 20 %

- < 30 %

- <

35 %

- < 13 %

- < 20 %

- <

25 %

< -40
<

-40

<

-40

<

-20

<

-26

<

-26

<

-20

<

-40

dBm
dBm
dBm
dBm
dBm
dBm
dBm
dBm

> 99 %

htooteulB .xaM .pyT.niM noitaludoM

Unit

Specification

< -70
<

-70

> -20

-20

>

< +13

+21

<

< 0

<

+5

dBm
dBm
dBm
dBm

dB
dB
dB
dB

mBd - 6 - 204.2
mBd - 6 - 144.2

Bd 1+ ot 4- - 6.1- - rewop timsnart evitaleR

Part Number LM-400

Page Number : 5 of 6

0121 270 6232 | www.lm-technologies.com | [email protected]

Adjacent channel selectivity C/I

-1 MHz

F=F

0

Adjacent channel selectivity C/I

+2 MHz

F=F

0

Adjacent channel selectivity C/I

-2 MHz

F=F

0

Adjacent channel selectivity C/I

+3 MHz

F=F

0

Adjacent channel selectivity C/I

-5 MHz

F=F

0

F0= 2405, 2441, 2477 MHz
Adjacent channel selectivity C/I
F=F

image

Pinout and Definition

π/4 DQPSK

- -11 -

8 DPSK - -5 ­π/4 DQPSK

- -40 -

8 DPSK - -40 ­π/4 DQPSK

- -23 -

8 DPSK - -20 ­π/4 DQPSK

- -45 -

8 DPSK - -45 ­π/4 DQPSK

- -45 -

8 DPSK - -45 -

π/4 DQPSK

-20

8 DPSK -15

< 0

+5

<

< -30

-25

<
< -20
<

-13

< -40

-33

<
< -40

-33

<

< -7

<

0

dB
dB
dB
dB
dB
dB
dB
dB
dB
dB

dB
dB

Part Number LM-400

Page Number : 6 of 6

0121 270 6232 | www.lm-technologies.com | [email protected]

Mechanical Dimension

-30mm x 27.5mm (L x W) +- 0.15mm

-Component height (unit: mm)

Notes

:

1. PIN9,10 DSR/DTR don’t use, they are no function currently.

2. PIN5 Pairing, the function have been changed to Data led indication

3. PIN6 Status, the function have not been specified.

4. RESET KEY
By pressing the Reset button, you can:

Disconnect and reconnect a wireless connection (a short press).
Restore the factory COM port 19200bps settings (over three seconds' press).

5. LED
Bluetooth link status

Part Number LM-400

Page Number : 5 of 6

Pin N o.

Pin N a me

Pin Type

Descr iption

1

G ND

G ND

C ommon ground

2

P VC C

Power

Power Amp. Power Supply(3.3V)

3

AIO (0)

Bi -directional

Programmable I/O terminal , 32KHz sleep clock input

4

AIO (1)

Bi -directional

Programmable I/O terminal

5

P IO (0)

Bi -directional

Programmable I/O terminal , RX Enable

6

PIO (1)

Bi -directional

Programmable I/O terminal , TX Enable

7

PIO (2)

Bi -directional

Programmable I/O terminal , USB_PULL_UP , C LK_REQ _O UT

8

PIO (3)

Bi -directional

Programmable I/O terminal , USB_WAK E_UP , CLK_REQ _IN

9

PIO (4)

Bi -directional

Programmable I/O terminal , USB_O N , BT_Priority/C h_Clk output for

co-existence signalling

10

G ND

G ND

C ommon ground

11

PIO (5)

Bi -directional

Programmable I/O terminal , USB_DETAC H , BT_Active output for co -

existence signalling

12

PIO (6)

Bi -directional

Programmable I/O terminal , CLK_REQ , WLAN_Active/C h_Data input

for for co-existence signalling

13

PIO (7)

Bi -directional

Programmable I/O terminal

14

PIO (8)

Bi -directional

Programmable I/O terminal

15

PIO (9)

Bi -directi onal

Programmable I/O terminal

16

RESET

C MO S input

Reset input of module, Active low reset

17

VC C

Power

Module power supply input

18

G ND

G ND

C ommon ground

19

G ND

G ND

C ommon ground

20

USB_DP

Bi -directional

USB data plus

21

USB_DN

Bi -directional

USB da ta minus

22

PCM_SYNC

Bi -directional

Synchronous data sync

23

PCM_IN

C MO S input

Synchronous data input

24

PCM_O UT

C MO S output

Synchronous data output

25

PCM_C LK

Bi -directional

Synchronous data clock

26

UART_RX

C MO S input

UART data input

27

UART_TX

C MO S output

UART data output

28

UART_RTS

C MO S output

UART request to send(active low)

29

G ND

G ND

C ommon ground

30

UART_C TS

C MO S input

UART clear to send(active low)

31

SPI_MO SI

C MO S input

Serial Peripheral Interface data input

32

SPI_CSB

C MO S input

C hip select for Synchronous Serial Interface(active low)

33

SPI_CLK

C MO S input

Serial Peripheral Interface clock

34

SPI_MISO

C MO S output

Serial Peripheral Interface data output

35

PIO (11)

Bi -directional

Programmable I/O terminal

36

PIO (10)

Bi -directional

Programmable I/O terminal

37

RF_IO

Analogue

Antenna interface

38

G ND

G ND

C ommon ground

0121 270 6232 | www.lm-technologies.com | [email protected]

FCC WARNING

This device complies with Part 15 of the FCC Rules. Operation is
subject to the following
two conditions: (1) this device may not cause harmful interference,
and (2) this device must
accept any interference received, including interference that may cause
undesired operation.

The antenna provided is a unique antenna. By installation of
unauthorized antenna to this equipment. Such unauthorized
installation could void the user's authority to opearte the equipment.

NOTE: The manufacturer is not responsible for and radio or TV
interference caused by unauthorized modifications to this equipment.
Such modifications could void the user’s authority to operate the
equipment.

10