1 (3)
The thermostat has a green LED-indication
which is switched off when the set temperature
is reached. The indicator also functions as a reference point for the temperature scale of the thermostat dial.
Temperature range for self-modulation
Self modulation 0%
Self modulation changing
Self modulation 100%
Temperature range for self-modulation , cycle time 10 min.
Installation
The following must be observed during assembly:
• Assembly height ca. 1.5 m above oor level.
• Assembly should preferably be carried out
on the inner wall.
• Ensure there is sufcient air circulation.
• Avoid secondary heat from other heat sources such as sunlight, lighting etc.
Electrical connection
1. Remove the thermostat dial.
2. Remove the cover via the click fastener at
the top-right hand corner of the case.
3. Carry out the electrical installation in
accordance with the connection diagram
(See below, or on the inside of the thermostat lid). NB! If LK Connection Box NC or
LK Connection Box 1 is used then the connection diagram for the specic product
should be used instead.
LK Room Thermostat S1 is an electronic room
thermostat with triac output adapted to LK oor
heating systems. The room thermostat is used
together with electrothermal actuators with normally closed function (NC). LK Room Thermostat S1 24V NC is available in three different designs, S1, S1 EXT and S1 Dti.
S1: Base thermostat for regulating room temperature (Article no. 241 72 86).
S1 EXT: Thermostat for regulating of room temperature or for e.g. regulating oor temperature
via external sensors (Article no. 241 72 90).
S1 Dti: Thermostat for regulating room temperature with hidden temperature settings for e.g.
public environment. There is also the possibility
of regulating e.g. oor temperature via external
sensors (Article 241 72 88).
Accessories
• LK Pattress S1 (Article no. 241 72 92)
• LK External Sensor S1, suitable for S1 EXT
respectively. S1 Dti (Article no. 241 72 94)
Features
• Self-modulating technology via signal pulses
for optimum energy effectiveness.
• Discrete and extremely thin thermostat design.
• Intended for direct mounting on walls, or
alternatively to electrical installation boxes.
• Connection of external temperature sensors
is possible for the models S1 EXT and S1 Dti.
• Temperature set back is possible via separate
clock (clock not included).
• Soundless thermostat function.
• Simple function control via LED.
Function description
For optimum energy efciency the room thermostat operates with so-called self-modulation technology via signal pulsing to the valve actuator.
Self-modulation technology adjusts the indicated
oor heating output in relation to the set temperature. When the room temperature reaches the
set temperature the output effect is reduced to
avoid overheating.
LK Room Thermostat S1, 24V NC
EN.33.C.99.1703
Assembly instructions | LK Room Thermostat S1, 24V NC
2 (3)
EN.33.C.99.1703
Assembly instructions | LK Room Thermostat S1, 24V NC
Limitation of thermostat dial installation range
The thermostat dial installation range can be limited. There are two plates beneath the dial which
can be moved to restrict the installation range as
per the diagram below.
Connection of LK External Sensor S1
LK External Sensor S1 is intended for use together with LK Room Thermostat S1 EXT or
LK Room Thermostat S1 Dti for regulating oor
temperature. Connect the sensor as follows:
1. Connect the external sensor to terminals
11 and 12 in the thermostat, see connection
diagram.
2. Change the switch on the circuit board from
INT to EXT, for external sensor.
3. If necessary the external sensor can be
extended up to 50 metres. Use the same
cable area or bigger than the sensor when
extending. NB! Avoid routing parallel close
to mains cable.
Error indication: If the LED ashes, this indicates
a broken contact with the external sensor, e.g. a
cable break.
The external sensor is placed as follows:
Embedding in concrete
Place the sensor in a conduit approx. 2 meters
into the room before embedding in concrete. Take
into consideration that the placement is at a representative point for the area that is going to be
adjusted. The end of the sensor is to be placed between two oor heating pipes. Seal the end of the
conduit with tape or similar to prevent concrete
from getting into the conduit. Try to place the conduit as high as possible since this gives a more optimal adjustment of the oor surface temperature.
The external sensor is slipped into the conduit before pouring the concrete and is connected to the
room thermostat as instructed above.
Click
Opening the cover.
24V~
1
4
2
5
LK Room Thermostat S1
24V~
EXT
INT
1
4
2
5
11
12
LK Room Thermostat S1 EXT and S1 Dti with possibility
for connection of LK External sensor S1.
3 (3)
EN.33.C.99.1703
Assembly instructions | LK Room Thermostat S1, 24V NC
Technical data
Voltage 24 V AC (20..30 V, 50/60 Hz) NC currentless
closed
Switch effect max 15 W (625 mA)
Max 5 LK Actuator 24V NC per room thermostat
Temp. range 5-35°C
Input for temp. reduction -3K
Cycle time for self-modulation 10 min
Range for self-modulation 2K
Colour, white polished RAL 9010
Protection Class III
Degree of Protection IP30
Storage temperature -20 to +70°C
Relative humidity (storage) 95% non-condensing
Working temperature 0 to +40°C
External sensor, length 4m, type NTC 47kΩ (additional)
With connected sensor, built-in temp limited to 42 °C
Energy declaration in accordance with
EU 811/2013
Temperature regulator class IV
Temperature regulator’s contribution to
seasonal space heating energy efciency
2%
Measurement
LK Room Thermostat S1.
4 m
ø 7
25
35
55
ø 5
LK External Sensor S1, length 4m.
ø 60
13,9
78
3,8
78,5
LK HeatFloor 22, LK EPS 30/50/70 or
LK Silencio
Mill a slot on the upper side of the board. Place a
conduit in the slot, end the conduit right between
two heat distribution plates. Take into consideration that the placement is at a representative
point for the area that is going to be adjusted. The
external sensor is slipped into the conduit before laying the oor and is connected to the room
thermostat as instructed above.
Floor heating in secondary spaced boarding
Place a conduit right between two heat distribution plates, attach the conduit on the edge of the
secondary spaced boarding using a clip for conduits. Take into consideration that the placement
is at a representative point for the area that is
going to be adjusted. The external sensor is slipped into the conduit before laying the oor and
is connected to the room thermostat as instructed
above.
LK EPS 16
Place a conduit along the long sides of the oor
heating installation facing the nearest short end.
Saw an approx. 2 meters long slot in the EPSboard and place the conduit in the slot. Take
into consideration that the placement is at a representative point for the area that is going to be
adjusted. The external sensor is slipped into the
conduit before laying the oor and is connected
to the room thermostat as instructed above.
LK Clip Rail 8/LK Clip Rail 12
Place a conduit along the long sides of the oor
heating installation facing the nearest short end.
Place the conduit at the short end between two
heating pipes and end it approx. 2 meters in. Seal
the end of the conduit with tape or similar to prevent concrete from getting into the conduit. The
external sensor is slipped into the conduit before pouring the concrete and is connected to the
room thermostat as instructed above.
LK Systems AB, Box 66, 161 26 Bromma, Sweden | www.lksystems.se
Loading...