Little Wonder PRUNER User Manual

Owners Manual and Safety Instructions

Pruner “E” System

Table of Contents

Important Information

A. Introduction

This attachment is designed for trimming light to medium size branches.

B. Pruner Attachment Specification.

C. Contents of the package

1. Pruner Attachment Assembly with plastic gear case cover

2. Chain Guide

3. Saw chain

4. Chain Guide cover

D. Service Information Contact

If you have questions about any topic in this Manual, or for the name of your local dealer, call 1-800-366-6268 toll free, Monday - Friday, 8:00 a.m. to 5:30 p.m., Eastern Time, or ask for Customer Service.

WARNING DANGER

ATTENTION: THIS SYMBOL POINTS OUT

IMPORTANT SAFETY INSTRUCTIONS

WHEN YOU SEE THIS SYMBOL

HEED ITS WARNING! STAY ALERT!

WARNING DANGER

READ & UNDERSTAND THIS MANUAL BEFORE

ATTEMPTING TO OPERATE THIS MACHINE.

TO REDUCE THE POTENTIAL FOR ACCIDENTS,

COMPLY WITH THE SAFETY INSTRUCTIONS IN

THIS MANUAL. FAILURE TO COMPLY MAY RESULT

IN SERIOUS PERSONAL INJURY AND OR

EQUIPMENT AND PROPERTY DAMAGE.

Important Information

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Special Safety Information . . . . . . . . . . . . . . . .1

Safety and Warnings

Safety Decals . . . . . . . . . . . . . . . . . . . . . . . . . .2

General Safety Rules . . . . . . . . . . . . . . . . . . . .3

Assembly Instructions . . . . . . . . . . . . . . .5

Operation . . . . . . . . . . . . . . . . . . . . . . . . . .7

Maintenance . . . . . . . . . . . . . . . . . . . . . . .8

Sharpening the Blade . . . . . . . . . . . . . . .10

Warranties Policy . . . . . . . . . .Back Cover

E. Special Safety Information

MODEL SHAFT TOTAL OIL TANK

LENGTH WEIGHT VOLUME

330106 29.5” 4.0 lbs.

(4.1 oz)

122ML

Safety and Warnings

A. Safety Decals

Please pay particular attention to the warning and information decals found on various parts of this Pruner Attachment unit. They are an important part of the safety system. These decals must be replaced in time due to abrasion, etc. It is your responsibility to replace the decals when they become hard to read. The location of these decals and their part numbers for ordering are shown below.

WARNING – DANGER

IMPROPER USE OR CARE OF THIS PRUNER,

OR FAILURE TO WEAR PROPER PROTECTION

CAN RESULT IN SERIOUS INJURY.

READ AND UNDERSTAND THE RULES FOR

SAFE OPERATION AND ALL INSTRUCTIONS

IN THIS MANUAL.

WEAR EYE AND HEARING PROTECTION,

HELMET AND PROPER CLOTHING.

READ AND

UNDERSTAND

OPERATOR’S MANUAL

BEFORE USING!

WARNING! WEAR

HELMET. DANGER OF

FALLING BRANCHES

WARNING! WEAR SLIP-RESISTANT

FOOTWEAR. MAINTAIN

FOOTING AND

BALANCE AT ALL

TIMES.

DO NOT STAND

ON SLIPPERY, UNEVEN

OR UNSTABLE

SURFACES. DO NOT

WORK IN ODD

POSITIONS OR ON A

LADDER. DO NOT

WARNING! DANGER

FROM OVERHEAD ELECTRIC POWER LINES. KEEP SAFE

DISTANCE!

KEEP BYSTANDERS AT

A SAFE DISTANCE

WARNING! WEAR EYE

AND EAR PROTECTION

WARNING!

Oilier Control Label

P/N 331178

P/N 331177

General Safety Rules

1. Remove branches in sections. Maintain safe operating positions, to avoid risk of being struck by falling branches or by those that rebound after hitting the ground

2. Cover saw chain with guard during transport and storage.

3. Do not hit rocks, stones, tree stumps, and other foreign objects with the working unit. If saw chain strikes an obstruction, stop engine immediately, unplug unit and inspect saw chain for damage.

4. Do not operate with a dull, fractured or damaged saw chain.

WARNING

WHEN USING ELECTRIC TOOLS, BASIC SAFETY

PRECAUTIONS, INCLUDING THE FOLLOWING,

SHOULD ALWAYS BE FOLLOWED TO REDUCE

THE RISK OF FIRE, ELECTRIC SHOCK AND

PERSONAL INJURY.

Pay particular attention to all sections regarding safety.

Read and understand all these instructions before operating this product and save these instructions. Be familiar with the controls and the proper use of equipment.

For safe operations:

1. Keep work area clean. Cluttered areas and benches invite injuries.

2. Consider work area environment. Do not expose power tools to rain. Do not use power tools in damp or wet locations. Keep work area well lit. Do not use power tools where there is risk of fire or explosion.

3. Guard against electric shock. Avoid body contact with earthed or grounded surfaces, e.g. pipes, radiators, stoves, ovens, refrigerators.

4. Keep children away

. Do not let visitors touch the tool or extension cord. All visitors should be kept away from area. Local regulations may restrict the age of the operator.

5. Store idle tools

. When not in use, tools should be stored in a dry, high or locked up place, out of reach of children.

6. Do not force the tool. It will do the job better and safer at the rate for which it was intended. Walk, never run.

7. Use the right tool. Do not force small tools or attachments to do the job of a heavy duty tool. Do not use tools for purposes not

intended; for example, do not use chain saw attachment to cut tree limbs or logs.

8. Dress properly

. Do not wear loose clothing or jewelry that can be caught in moving parts. Long trousers, non-slip gloves and sturdy work shoes with non-skid soles are recommended when working outdoors. Wear protective hair covering to contain long hair.

9. Use protective equipment. To avoid injury, wear ear, eye protection, face or dust mask if the operation is dusty. To avoid injury from falling branches, wear helmet. Eye protection must meet ANSI Z

87.1 requirements.

10. Do not abuse the cord

. Never carry the tool by the cord or yank it to disconnect it from the socket. Keep the cord away from heat, oil and sharp edges.

11. Maintain tool with care

. Keep cutting tools sharp and clean for better and safer performance. Follow instructions for lubrication and changing accessories. Inspect tool cord periodically and if damaged, have it repaired by an authorized service facility. Inspect extension cords periodically and replace, if damaged. Keep handles dry, clean and free from oil and grease.

12. Disconnect tools

. When not in use, before servicing and when changing accessories such as blades, bits and cutters.

13. Remove adjusting keys and wrenches

. Form the habit of checking to see that keys and adjusting wrenches are removed from the tool before turning it on.

14. Avoid unintentional starting. Do not carry a plugged in tool with a finger on the switch trigger. Ensure switch is off when plugging in.

15. Use outdoor extension leads

. When tool is used outdoors, use only extension cords intended for outdoor use.

16. Important extension cord information:

a. Make sure the extension cords are in good condition

before use.

b. Based on the total length of cord that you are going

to use, check the chart to make sure the cord meets the correct minimum cord gauge (AWG) requirements.

IMPORTANT NOTE:

Using an undersized cord or a larger number cord gauge (AWG) than recommended in the chart, will cause a loss in power and overheating of the unit. Using a smaller number cord gauge (AWG) than recommended in the chart, is acceptable.

Extension cord chart (minimum cord gauge (AWG))

17. Stay alert

. Watch what you are doing. Use common sense. Do not operate tool when you are tired, ill or under the influence of alcohol or other drugs.

18. Check damaged parts

. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, free running of moving parts, breakage of parts, mounting and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated in this instruction manual. Have defective switches replaced by an authorized service facility. Do not use the tool if the switch does not turn it on and off.

Don’t operate the machine with a damaged or excessively worn cutting device.

Length (feet) 1 to 25 26 to 50 51 to 100 101 to 150

Cord gauge (AWG) 18 16 14 12

WARNING – DANGER

LITTLE WONDER WILL NOT BE RESPONSIBLE

FOR THE FAILURE OF CUTTING DEVICES OR

ACCESSORIES THAT HAVE NOT BEEN TESTED

AND APPROVED FOR USE WITH THIS UNIT.

USE ONLY MANUFACTURER-RECOMMENDED

REPLACEMENT PARTS.

19. The use of any accessory or attachment, other than those recommended in this instruction manual, may present a risk of personal injury.

20. Have your tool repaired by a qualified person. This electric tool conforms to relevant safety requirements. Repairs should only be carried out by qualified persons using original spare parts, otherwise this may result in considerable danger to the user.

21. Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people or their property.

22. Work only in daylight or in good artificial light.

23. Keep all guards attached at all times when unit is operated.

24. Always use the shoulder strap. Adjust the strap for comfort before starting the engine.

25. Secure unit during transport

to prevent damage or injury.

26. Machine should not be used in any position that causes

any part to come within 10 feet of overhead electrical lines. Always be aware of overhead power lines.

27. Always keep a firm grip on both handles when motor is

running: one hand grasps the front “loop” handle while the other hand grasps the rear handle. Severe injuries can result if you try to use this machine with only one hand or with an insecure grip.

28. Thoroughly inspect the area where equipment is to be

used and removed all objects, which can be thrown by the machine.

29. Always keep area clear of children, pets, and bystanders.

30. Always inspect your unit before each use and ensure that

all handles, guards and fasteners are secure, operating, and in place. Be sure that all electrical cords are not damaged or broken.

31. Always maintain and examine your attachments with care.

Follow maintenance instructions given in manual.

32. Don’t attempt to repair any part of the extended reach

“E” system. Have repairs made by a qualified repairman. See that only original “Mantis” parts are used.

33. Maintain a firm footing and good balance, do not overreach while trimming. Before you start to trim, check the work area for obstacles that might cause you to lose your footing, balance or control of the machine. While operating the machine always be sure of a safe and secure operating position especially when using steps or a ladder. Always be sure of your footing on slopes.

WARNING – DANGER

IMPROPER ASSEMBLY OF THIS EQUIPMENT

CAN RESULT IN SERIOUS INJURY. MAKE SURE

TO FOLLOW ALL INSTRUCTIONS CAREFULLY.

IF YOU HAVE ANY QUESTIONS, CONTACT

MANTIS CUSTOMER SERVICE.

34. Always disconnect power cord from power source:

a. Before cleaning blockages.

b. Before checking, cleaning or working on the

cutting portion of the unit.

c. After striking a foreign object: inspect the cutting

part for damage and make repairs before restarting and operating the unit.

d. If machine starts to vibrate abnormally (check

immediately).

e. Whenever you leave the unit.

+ 10 hidden pages