Lithonia Lighting TWP-LED Installation Manual

READ AND FOLLOW ALL SAFETY INSTRUCTIONS!

SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION

· To reduce the risk of death, personal injury or property damage from re, electric shock, falling parts, cuts/
abrasions, and other hazards please read all warnings and instructions included with and on the xture box and all
xture labels.

· Before installing, servicing, or performing routine maintenance upon this equipment, follow these general
precautions.

· Installation and service of luminaires should be performed by a qualied licensed electrician.

· Maintenance of the luminaires should be performed by person(s) familiar with the luminaires’ construction and
operation and any hazards involved. Regular xture maintenance programs are recommended.

· It will occasionally be necessary to clean the outside of the refractor/lens. Frequency of cleaning will depend on
ambient dirt level and minimum light output which is acceptable to user. Refractor/lens should be washed in a
solution of warm water and any mild, non-abrasive household detergent, rinsed with clean water and wiped dry.
Should optical assembly become dirty on the inside, wipe refractor/lens and clean in above manner, replacing
damaged gaskets as necessary.

· DO NOT INSTALL DAMAGED PRODUCT! This luminaire has been properly packed so that no parts should have
been damaged during transit. Inspect to conrm. Any part damaged or broken during or after assembly should be
replaced.

· Recycle: For information on how to recycle LED electronic products, please visit www.epa.gov.

· These instructions do not purport to cover all details or variations in equipment nor to provide every possible

contingency to meet in connection with installation, operation, or maintenance. Should further information be
desired or should particular problems arise which are not covered suciently for the purchaser’s or owner’s
purposes, this matter should be referred to Acuity Brands Lighting, Inc.

WARNING

RISK OF ELECTRIC SHOCK

Disconnect or turn o power before installation or

servicing.

Verify that supply voltage is correct by comparing it with

the luminaire label information.

Make all electrical and grounded connections in

accordance with the National Electrical Code (NEC) and
any applicable local code requirements.

All wiring connections should be capped with UL approved

recognized wire connectors.

CAUTION

RISK OF INJURY

Wear gloves and safety glasses at all times when removing

luminaire from carton, installing, servicing or performing
maintenance.

Avoid direct eye exposure to the light source while it is on.

WARNING

RISK OF BURN

Allow lamp/xture to cool before handling. Do not touch

enclosure or light source.

Do not exceed maximum wattage marked on luminaire

label.

Follow all manufacturer’s warnings, recommendations

and restrictions for: driver type, burning position,
mounting locations/methods, replacement and recycling.

CAUTION

RISK OF FIRE

Keep combustible and other materials that can burn,

away from lamp/lens.

Do not operate in close proximity to persons, combustible

materials or substances aected by heat or drying.

Please see product specic installation instructions for additional warnings or any applicable FCC or other regulatory statements.

Failure to follow any of these instructions could void product warranties. For a complete listing of product Terms and Conditions, please visit www.acuitybrands.com.

Our Brands Indoor/Outdoor Indoor Lighting Outdoor Lighting Controls Daylighting

Lithonia Lighting Gotham American Electric Lighting DARK TO LIGHT SunOptics

Carandini Mark Architectural Lighting Antique Street Lamps LC&D
Holophane Peerless Hydrel ROAM

RELOC Renaissance Lighng Tersen Sensor Switch
Light Concepts Winona Lighting Synergy

Acuity Brands Lighting, Inc. assumes no responsibility for claims arising out of improper or careless installation or handling of its products.

ABL LED General Warnings, Form No. 503.203

© 2010 Acuity Brands Lighting, Inc. All rights reserved. 12/01/10

Installation Instructions
TWP-LED

DELIVERY: Upon receipt of xture and accessories (packed separately), thoroughly inspect
for any freight damage. All damage should be reported to the delivery carrier. Compare
the catalog description listed on the packing slip with the xture label on the inside of
the housing to be sure you have received the correct merchandise.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.

5 year limited warranty

Outlet box mounting:

1. Loosen the 2 captive screws in the front housing and remove front cover from xture.

2. Remove electrical splice compartment cover. Keep (2) 8-32 screws for reinstallation.

3. Remove center knock out and feed wires through.

4. Mount xture using dimensions shown in Figure A.
4a. If provided with an ALO device, adjust the dial to the required lumen level (use ALO table as reference), by turning it using
a small at head screwdriver.

5. Make supply connections. Reinstall the (2) 8-32 screws and electrical splice component cover removed in step 2, making
sure no wires are pinched.

6. Replace front cover.

7. Tighten the 2 captive screws (30-35in lbs). Do not over tighten. Over tightening will cause stripping and void all warranties.

15-3/4”

Electrical splice
compartment
cover

Condulet Tee mounting:

1. Loosen the 2 captive screws in the front housing and remove
front cover from xture.

2. Remove electrical splice compartment cover and driver
cover. Keep (2) 8-32 and (2) 10-24 screws for reinstallation.

3. Remove top conduit cover disc.

4. Mount xture using dimensions shown in Figure A. Thread
conduit into xture.

5. Make supply connections. Reinstall both compartment
cover and driver cover using (2) 8-32 and (2) 10-24 screws
removed in step 2, making sure no wires are pinched.

6. Replace front cover.

7. Tighten the 2 captive screws. Do not over tighten. Over
tightening will cause stripping and void all warranties.

15-1/4”

3/8” KO (3)

1-13/16”

4-1/4”

7/8” KO

2-1/2”

Conduit cover disc

5”

2-7/8”

Lithonia Lighting Outdoor • One Lithonia Way • Conyers, Georgia 30012

Phone: [phone] • Fax: [phone] • www.lithonia.com

© 2011 Acuity Brands Lighting, Inc. All rights reserved.

Part Number: RJ521354 REV C

Revision Date: 11-28-18

Installation Instructions
TWP-LED

FIXTURE MOUNT:

Figure D

Figure E

1. Drill xture per drilling detail
(Figure D). NOTE: Remove photo­electric cell (when provided) before
drilling for xture mounted wire

1”from
wall

guard.

2. Place wire guard over xture.

7 1/2”

3. Secure in place with two (2) 10­24 fasteners, washers, and spacers
(provided) as shown (Figure E).

Troubleshooting: If this xture fails to operate properly, check to make sure: • The xture is wired correctly. • The xture is grounded
correctly. • The line voltage at the xture is correct. If all these variables have been checked and the xture still does not operate as
specied, contact your local Lithonia Lighting distributor.

Lithonia Lighting Outdoor • One Lithonia Way • Conyers, Georgia 30012

Phone: [phone] • Fax: [phone] • www.lithonia.com

© 2011 Acuity Brands Lighting, Inc. All rights reserved. 11/12

Part Number: RJ521354 REV C

Revision Date: 11-28-18