Lithonia Lighting OLF 2SH 40K 120, OLF 3RH 40K 120, OLF 2SH 40K 120 PE, OLF 2RH 40K 120, OLF 3RH 40K 120 PE Installation Instructions Manual

LED Security Floodlight

Model Number(s):

OLF 2SH 40K 120
OLF 2SH 40K 120 PE*

INSTALLATION INSTRUCTIONS

Model Number(s):

OLF 3RH 40K 120
OLF 3RH 40K 120 PE*

Model Number(s):

OLF 2RH 40K 120
OLF 2RH 40K 120 PE*

* PE denotes photocell option

Protect yourself. Before installing, read the entire instructions carefully and save them for future reference.

Date installed:_____________

Failure to follow any of these instructions could void product warranties. For a complete list of product Terms and
Conditions, visit www.acuitybrands.com. Acuity Brands Lighting, Inc. assumes no responsibilities for claims arising out of
improper or careless installation or handling of its products.

If further technical assistance is required, contact: Technical Support at: [phone].

Suitable for wall mount or eave mount.

Not suitable for ground mount installation.

Mounting Hardware Included

Silicone Sealant Required

page 1

UOLF_Rev 8/17/15

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW THESE SAFETY INSTRUCTIONS!

electric shock, falling parts, cuts/abrasions, and other hazards please

• Before installing, servicing, or performing routine maintenance upon this
equipment, follow these general precautions.

• Commercial installation, service and maintenance of luminaires should

• For Residential installation: If you are unsure about the installation or

and check your local electical code.

• Maintenance of the luminaires should be performed by person(s)
familiar with the luminaires’ construction and operation and any hazards

grounded UL listed junction box.

• It will occasionally be necessary to clean the outside of the refractor/
lens. Refractor/lens should be washed in a solution of warm water and
any mild, non-abrasive household detergent, rinsed with clean water and
wiped dry. Should optical assembly become dirty on the inside, wipe
refractor/lens and clean in above manner, replacing damaged gaskets
as necessary.

• DO NOT INSTALL DAMAGED PRODUCT! This luminaire has been
properly packed so that no parts should have been damaged during

assembly should be replaced.

• Recycle: For information on how to recycle LED electronic products,
please visit www.epa.gov.

• These instructions do not purport to cover all details or variations
in equipment nor to provide every possible contingency to meet in
connection with installation, operation, or maintenance. Should further
information be desired or should particular problems arise which are not

CAUTION

RISK OF FIRE

Keep combustible and other materials that can burn, away from lamp/

lens.

Do not operate in close proximity to persons, combustible materials or

substances affected by heat.

CAUTION
RISK OF PRODUCT DAMAGE

Never connect components under load.

jacket or damage wire insulation.

an LED product directly to a dimmer packs, occupancy sensor, timing

directly off a switched circuit.

will prevent convection or cooling.

LED products are Polarity Sensitive. Ensure proper Polarity before

installation.

grounding equipment must be worn during all installation or servicing
of unit.

Do not touch individual electrical components as this can cause ESD,

shorten lamp life, or alter performance.

should be referred to Acuity Brands Lighting, Inc.

WARNING
RISK OF ELECTRIC SHOCK

Disconnect or turn off power before installation or servicing.
Verify that supply voltage is correct by comparing it with the luminaire

label information.

Make all electrical and grounded connections in accordance with

the National Electrical Code (NEC) and any applicable local code
requirements.

All wiring connections should be capped with UL approved wire

connectors.

CAUTION
RISK OF INJURY

Wear gloves and safety glasses at all times when removing luminaire

from carton, installing, servicing or performing maintenance.

Avoid direct eye exposure to the light source while it is on.

WARNING
RISK OF BURN

or light source.

Do not exceed maximum wattage marked on luminaire label.
Follow all manufacturer’s warnings, recommendations and restrictions

including but not limited to: driver type, burning position, mounting
locations/methods, replacement and recycling.

Use only lamps that comply with ANSI standards.

unlikely event your unit may require service, stop using the unit
immediately and contact an ABL representative for assistance.

Lighting could void the authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a
class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
when used in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

5-YEAR LIMITED WARRANTY

Failure to follow any of these instructions could void product warranties.
For a complete listing of product Terms and Conditions, please visit www.
acuitybrands.com. Acuity Brands Lighting, Inc. assumes no responsibilities
for claims arising out of improper or careless installation or handling of its
products.

page 2