Lithonia Lighting LVS 120/277 ELN SD, EXTREME LVS 120/277 ELN SD, LVS2 120/277 ELN SD Supplement Manual

INSTALLATION INSTRUCTION SUPPLEMENT

EM ER GE NC Y LIG HT IN G SY ST EM S

TE L: 800 -3 34 -86 94 Fa x: 77 0- 981 -8 14 1 w ww. li th on ia. co m

EXTREME

®

LED EMERGENCY EXIT SIGNS

WITH SELF-DIAGNOSTICS OPTION

SERIES L VS 120/277 ELN SD and LVS2 120/277 ELN SD

CAUTION: For safety and proper operation, read and follow instructions carefully before installation.

IMPORTANT SAFEGUARDS

1.READ AND FOLLOW ALL
SAFETY INSTRUCTIONS

2. Before wiring to power supply, turn off electricity at fuse or circuit

breaker.

3. Disconnect A.C. power and Power Plug before servicing.

4. Refer to wiring diagram sheet for proper connections.

5. Be sure unit is wired to AC power before power plug is connected.

6. All servicing should be performed by qualified personnel.

7. Consult your local building code for approved wiring and
installation.

8. Do not use outdoors.

9. Do not mount near gas or electric heater.

10. Fixture must be grounded to avoid potential electric shock.

11. Equipment should be mounted in location and at heights where it
will not readily be subjected to tampering by unauthorized
personnel.

12. The use of accessory equipment not recommended by the
manufacturer may cause an unsafe condition.

13. Do not use this equipment for other than intended use.

U.S. Patent No. D383,501

SA VE THESE INSTRUCTIONS

Important Note:

This Instruction sheet supple-

ment is to be used in conjunction with the Installa-

tion Instructions provided with the unit.

PARTS DESCRIPTION

a Charger PC Board
b Self-Diagnostics PC Board
c Pushnut Connectors
d Battery
e Battery Connector
f Lamp Connector Cable
g Self-Diagnostics Harness (to Test Switch/

h Self-Diagnostics Harness (to Charger PCB)
i Lampboard
j Manual Test Switch
k Test Switch/Status Indicator Connector
l Magnetic Test Switch
m Lamp Connector
n Charger Board/Self-Diagnostics Connections

Figure A
Single Face Exit

Status Indicator connector)

SINGLE FACE EXIT

INSTALLATION:

1. Refer to main
installation, mounting, cleaning instructions and additional
figures detailing unit.

Important Note:

the test switch/status indicator connector k, and the lampboard
connector m before removing the lampboard i from the unit.

WIRING:

Note:

Select appropriate wiring diagram for input voltage to be

used.

Important Notes:

1. This equipment to be connected to an unswitched circuit
only.

2. Cap all unused leads separately.

3. Canopy mount exits have polarized connectors on A.C.
installation wire leads and option installation wire leads.

4.

CAUTION:

tor is connected to charger board for a prolonged period of
time without continuous A.C. power provided.

Installation Instructions

Care should be taken to disconnect both

Damage to battery will occur if battery connec-

manual for all

Single Lamp 120 volt wiring

Page 2

Single Lamp 277 volt wiring

PARTS DESCRIPTION

a Charger PC Board
b Self-Diagnostics PC Board
c Pushnut Connectors
d Battery
e Battery Cable
f Lamp Connector Cable
g Self-Diagnostics Harness (to Test Switch/Status

Indicator connector)

h Self-Diagnostics Harness (to Charger PCB)
i Lampboard
j Manual Test Switch
k Test Switch/Status Indicator Connector
l Magnetic Test Switch
m Lamp Connector
n Charger PCB/Self-Diagnostics connections

Figure B
Dual Face Exit

DUAL FACE EXIT

INSTALLATION

1. Refer to main

installation, mounting, cleaning instructions and additional
figures detailing unit.

Important Note:

the test switch/status indicator connector k, and the lampboard
connector m before removing the lampboard i from the unit.

Wiring

Note:

Select appropriate wiring diagram for input voltage to be

used.

Important Notes

1. This equipment to be connected to an unswitched circuit

only.

2. Cap all unused leads separately.

3. Canopy mount exits have polarized connectors on A.C.

installation wire leads and option installation wire leads.

4.

CAUTION:

tor is connected to charger board for a prolonged period of
time without continuous A.C. power provided.

Installation Instructions

Care should be taken to disconnect both

Damage to battery will occur if battery connec-

manual for all

Dual Lamp 120 volt wiring

Dual Lamp 277 volt wiring

Page 3

Self Diagnostics Testing:

EM ER GE NC Y LIG HT IN G SY ST EM S

TE L: 800 -3 34 -86 94 Fa x: 77 0- 981 -8 14 1 w ww. li th on ia. co m

Important Note:

tested as often as local codes require, or at least monthly, to
ascertain that all components are operational. Allow battery to
charge 24 hours before initial testing, and 168 hours to fully
charge battery.
tests to satisfy these test requirements, as well as local code
testing requirements for most areas.

Status Indicator

1.

Normal Operation:

with A.C. power supplied, the status indicator will be green and
the exit lamp will be on.

2.

Testing:

the exit lamp on, a test is in process. The exit performs two
types of tests. Every 28 days (+/- 2 days) it performs a monthly
test. The monthly test is a five minute diagnostics test of the
battery, lamp(s), and charging circuit. Upon completion of the
five minute test, the status indicator should return to green
(steady) to indicate a properly functioning unit. A flashing red
status indicator indicates a failure condition. Every 6 months (+/

- 12 days) self-diagnostics performs a 6 month test. The 6

month test is a 30 minute diagnostics test of the battery,
lamp(s), and charging circuit. After the 30 minute test, the
status indicator should return to green (steady) to indicate a
properly functioning unit. A flashing red status indicator
indicates a failure condition.

3.

Failure Indication:

red, the exit needs service. The self-diagnostics system has
detected a low battery, bad lamp(s), or a charger circuit failure.
At this time the exit failure should be diagnosed and serviced by
quailified personnel.

Note:

servicing unit.
Refer to the

replacing parts.
After the unit has been serviced, and continuous power applied

to the unit, the diagnostic systems clock will reset. This will be
indicated by the status indicator being green, and the exit lamp
being on.

Turn off A.C. power and disconnect battery before

Maintenance

Emergency lighting systems should be

Note:

The self-diagnostics option performs

When unit is functioning properly,

When the status indicator is flashing green with

When the status indicator is flashing

section of these instructions when

Manually Clearing a Failure:

A failure indication may be cleared manually by:

1. Placing the unit in the manual test mode for more than 30
seconds.

2. Removing AC power for more than 30 seconds.
If a failure condition is detected during the next self-diagnostics

test, the failure indicator will flash red, indicating a failure
condition.

Manual Testing:

Important Note:

satisfy local codes in most areas. Although self-diagnostics
does not allow a manually initiated self-diagnostics test, there
are two methods to simulate an AC power failure and initiate a
test of the battery, lamp(s), and charger circuit:

If desired, manual testing of the unit may be actuated as
follows:

1. Hold the magnet to the magnetic test zone. The status
indicator will go out when the magnet is positoned correctly,
indicating the manual test mode has been activated. Remove
the magnet to end the test and return the unit to normal
operation. The status indicator should return to green, indicating

a properly functioning unit.

2. Press the manual test switch (located inside the unit on the
lampboard). The status indicator will go out to indicate the
manual test mode has been activated. Release the test switch
to end the test and return the unit to normal operation. The
status indicator should return to green, indicating a properly

functioning unit.

The self-diagnostics option performs test to

Maintenance:

Note:

Lampboard Replacement:

1. Disconnect lamp connector m, and test switch/status

Turn off A.C. power and disconnect battery before

servicing unit.

indicator connector k (if applicable). Remove (4) screws
holding lampboard i in place and remove lampboard.
Lampboard replacement is a reverse sequence of above.

Manual Magnetic

Test Zone

Multi-color LED Status Indicator
Green: Normal operation
Green Flashing: Performing Self-Diagnostics Test
Red Flashing: Failure Condition

Figure C

Self-Diagnostics Status Indicator and Manual
Magnectic Test Switch

Page 4

Battery Replacement

1. Cut cable tie holding battery d to bracket. Pry battery from
battery bracket to release from tape. Replacement is a
reverse sequence of above.

Charger P.C. Board Replacement:

1. Cut tape and open enclosure box for Charger P.C. Board.
Disconnect lamp connector, and test switch/status light
connector.

2. Cut installation supply leads and charger board/self-diagnos­tics connections n at pushnut connector c. Strip installation
supply leads and self-diagnostics leads for pushnut connec­tion.

3. Charger pc board replacement is a reverse sequence of
above.

Part Number EMCSA00490

REV. C