Lithonia Lighting EU2C Installation Instructions Manual

DO NOT PRINT with INSTRUCTIONS

Information below is for LITHONIA documentation purposes only.
DO NOT include this page in the printing of this instruction sheet.

PART NUMBER: EMCSA00911

DESCRIPTION: INSTRUCTION SHEET, EU2C
SPECIFICATIONS: Prints 8.5 x 11, portrait. Two side, one color: BLACK ink.
PAGINATION: 8.5” X 11 portrait.

REQUIRED INSTRUCTION SHEETS for EU2C models

PART # INSTRUCT SHEET DESCRIPTION REV DATE STANDARD UNIT

EMCSA00911

EMCSA00795 ABL LED WARNING X

EMCSA00912

EU2C B 09.12.2018 X

SD INSTRUCTIONS

A 08.06.2018

CONFIGURATIONS

DATE CHANGE DESCRIPTION BY

9.12.18 REV. B: Removed SD HO wiring diagram - ABL not offering SD and hO together at this time.

8.06.18 REV. A: Initial Release

HO

X
X

SDT

X
X

RRB

RRM

PAGE: 0 of 4

One Lithonia Way, Conyers GA 30012

Phone: [phone]

www.lithonia.com

DO NOT PRINT with INSTRUCTIONS

INSTALLATION INSTRUCTIONS for Lithonia Lighting EU2C Models

LED DUAL HEAD EMERGENCY LIGHTING FIXTURE

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

WARNING:

AND WARNINGS MAY RESULT IN DEATH, SERIOUS INJURY OR
SIGNIFICANT PROPERTY DAMAGE. For your protection, read and
follow these warnings and instructions carefully before installing or
maintaining this equipment. These instructions do not attempt to cover
all installation and maintenance situations. If you do not understand
these instructions or additional information is required, contact
LITHONIA LIGHTING or your local LITHONIA LIGHTING distributor.

WARNING: RISK OF ELECTRIC SHOCK - NEVER CONNECT

TO, DISCONNECT FROM, OR SERVICE WHILE EQUIPMENT IS
ENERGIZED.

WARNING: RISK OF FIRE. Lamps are hot. Keep combustible material away from hot parts. Observe lamp manufacturer’s warnings,

recommendations and restrictions on lamp operation and maintenance. Make sure lamps are correctly installed.

CAUTION: The battery in this unit may not be fully charged. After electricity is connected to unit, let battery charge for at least 24

hours, then normal operation of this unit should take effect. To check, press the TEST button. The lamps on the unit should turn on.

NOTE: Complies with California Title 20. Product label is marked with .
IMPORTANT SAFEGUARDS: When using electrical equipment, basic safety precautions should

always be followed, including the following:

• Do not use outdoors.

• Consult local building code for approved wiring and installation.

• Disconnect AC power before servicing and installation.

• Do not mount near gas or electric heaters.

• Do not use this equipment for anything other than its intended use.

•

The use of accessory equipment not recommended by the manufacturer will vo id product listing and warrant y and may c ause an uns afe conditio n.

• Any service on this equipment should be performed by qualified personnel only.

• Equipment should be mounted in locations and at heights where it will not be subject to tampering by unauthorized personnel.

• Do not ceiling mount.

• Use caution when servicing batteries.

• Cap unused wires with enclosed wire nuts or other approved method.

• Make sure wire terminations are secure and leads are properly tucked in appropriate wire channels.

FAILURE TO FOLLOW THESE INSTRUCTIONS

INSTALLATION:
NOTE: Max mounting height is 10 ft to achieve at least 1 ft-candle of illuminance in emergency mode.

BATTERY CONNECTOR

PLUG IN

Fig.B

PAGE: 1 of 4

Fig.A (J-Box)

SAVE THESE INSTRUCTIONS

and deliver to owner after installation

Fig.C

INSTALLATION INSTRUCTIONS

J-BOX MOUNTING:

1.

Feed fixture leads through the back plate and connect to AC power supply (Fig A, page 1). For 120V use black and white wires
and for 277V, use red and white wires.

2.

Attach back plate to J-Box and secure with screws.

3.

Complete the battery connection. (Fig. B, page 1)

4.

Align snaps and push housing directly onto the back plate (Fig. C, page 1). Apply continuous AC power.

5.

After the battery has been left to charge for 24 hours, test the unit by pushing the test switch and the LED lamp head will turn

CONDUIT MOUNTING:

1. Secure back plate to wall surface using keyhole knockouts on the back plate.

2. Route wires through hole in conduit flange and make conduit connection. For 120V use black and white wires and for 277V, use

red and white wires.

3. Complete the battery connection (Fig. B, page 1).

4. Align snaps and push housing directly onto the back plate. Apply continuous AC power.

5. After battery has been left to charge for 24 hours, test the unit by pushing the test switch and the LED lamp head will turn ON.

WALL MOUNTING:

1. Secure back plate to wall surface using keyhole knockouts on the back plate.

2. Feed fixture leads through back plate and connect to AC power supply. For 120V use black and white wires and for 277V, use

red and white wires.

3. Complete the battery connection (Fig. B, page 1).

4. Align snaps and push housing directly onto the back plate. Apply continuous AC power.

ON.

5. After battery has been left to charge for 24 hours, test the unit by pushing the test switch and the LED lamp head will turn ON.

OPERATION:

1. During an electrical power failure, the LED lamps will automatically come on for a minimum of 90 minutes.

2. To test, press the "TEST" switch. The emergency LED lamps will illuminate and LED indicator will turn OFF. When the switch
is released, the lamps will turn OFF and the LED indicator will turn ON.

LED STATUS INDICATOR KEY and TROUBLESHOOTING:

Visual Status Indicaon Troubleshoong/Acons to Take
RED

GREEN

UNLIT

1. Baery connecon is not made.

2. Baery has been diagnosed as dead or defecve aer 24

hours of connuous charging with AC power supplied.

Baery is connected, AC power has been supplied and xture is in
charging state.

AC power has not been supplied.

1. Make connecon; or if baery is connected, disconnect
battery for eight seconds and then reconnect.

2. Replace the battery.

This is the normal state. No acon required.

Supply AC power.

TESTING:

National Electric Code (NEC) and NFPA 101 regulations require that routine tests need to be performed as listed below: Once every
month, the unit needs to be tested for duration of 30 seconds. Push in and hold the test switch to perform this test. Once every 12
months, a full 90 minute (per UL requirements) test needs to be performed on the unit. Disconnect power to the unit and leave it in
the emergency mode. The lamps should stay ON for at least 90 minutes. Written records of the testing are to be kept for
examination by the authority having jurisdiction.

PAGE: 2 of 4

SAVE THESE INSTRUCTIONS

and deliver to owner after installation

TROUBLESHOOTING:

Condition - The emergency lights do not operate

1. If the charge indicator light is OFF: Check that the circuit breaker for AC supply is ON.

2. If the charge indicator light is ON: Check that battery is properly connected. If problem persists, Replace battery. If remote lamps (where appli­cable) are connected to the equipment, then turn OFF the AC supply and disconnect the remote circuit wires from the equipment. Turn ON the
AC supply and depress the test switch. If the local lamps (mounted on the equipment itself) come ON, then check the remote circuit for short or
overload condition and correct as required. Reconnect the circuit wires and restore AC power. If the local lamps don’t turn ON after disconnecting
the remote circuit wires, then replace battery.

Condition - Emergency lights are dim

1. Battery not fully charged. Allow battery to recharge for 24 hours and then retest. If lights are still dim, replace battery.

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

WIRING DIAGRAMS

REMOTE CAPABLE

AC INPUT CONNECTOR
(MOUNTING PLATE)

277V

RED

120V

BLACK

WHITE

0V

YELLOW(+)

BLUE(-)

YELLOW(+)

LAMP

TO REMOTE

BLUE(-)

YELLOW(+)

BLUE(-)

LAMP

CHARGER

BOARD

TEST

READY

Note for HO models:

Use 18-22 AWG stranded
wire to connect remote lamp

heads.

Note:

Unused input lead must
be properly insulated with
wire nut or other approved
method.

RED

BLACK

AC INPUT CONNECTOR
(MOUNTING PLATE)

RED

277V

BLACK

120V

WHITE

0V

YELLOW(+)

BLUE(-)

YELLOW(+)

LAMP

BATTERY

BLUE(-)

LAMP

CHARGER

BOARD

RED

BLACK

BATTERY

TEST

READY

PAGE: 3 of 4

SAVE THESE INSTRUCTIONS

and deliver to owner after installation

INSTALLATION INSTRUCTIONS

CHARGER

AC INPUT CONNECTOR
(MOUNTING PLATE)

0V

RED

BLACK

WHITE

LAMP

YELLOW(+)

WHITE

BLUE(-)

YELLOW(+)

WHITE

BLUE(-)

LAMP

277V

120V

BOARD

READY

TEST

RED

BLACK

BATTERY

PAGE: 4 of 4

One Lithonia Way, Conyers GA 30012

Phone: [phone]

www.lithonia.com

SAVE THESE INSTRUCTIONS

and deliver to owner after installation

Part No. EMCSA00911, REV B

2018.09.12