MODEL LBT SERIESBLUETOOTH CEILING SPEAKER
Please ensure you read the entire instruction manual carefully before you commence any work.
Carefully unpack the speakers from the packaging. Please check to ensure all the parts shown
below are included.
If any parts of the speaker appear damaged, please contact your dealer/reseller immediately or
contact www.LitheAudio.com for contact details.
THANK YOU FOR
CHOOSING LITHE AUDIO
BOX CONTENTS
Listed below is the hardware equipment needed to install the speaker, with the addition of
a ladder to ensure the installation is done safely. A cutting template is included in the box.
Innovative design and advanced engineering built in to our LBT series of wireless Bluetooth
ceiling mount speakers. Designed for easy installation and high quality sound, within seconds each
room is setup and ready. This manual describes the installation of LBS series speakers within
conventional stud and sheetrock (Joist and plasterboard) ceilings.
IMPORTANT SAFETY WARNING
Before use please read completely and use in accordance with these safety instructions.
Before commencing any electrical work ensure the supply is switched OFF at the mains. Either
by switching off the consumer unit or by removing the appropriate fuse. This product should
be installed in accordance with the relevant sections of the building regulations code and in
accordance with the latest edition of IEE regulations (BS 7671).
If the unit is to be used as a replacement for an existing product, remove the existing unit from its
location and disconnect the wiring. Connect the wires as shown in diagram. Ensure terminals are
properly tightened and ensure no bare wires are visible. When tting the speaker into the ceiling,
ensure no wires are trapped.
READ THE INSTRUCTIONS CAREFULLY BEFORE STARTING THE
INSTALLATION PROCESS AND KEEP THEM SAFE FOR FUTURE
REFERENCE.
• Failure to follow the instructions in this guide voids all warranties on your speakers.
• Warning: Do not use the product in water.
• Warning: Do not install speaker directly above any heat sources such as radiators, or other
apparatus that produce heat.
• Warning: To reduce the risk of re or electric shock, do not expose this speaker to rain or
moisture (directly above bath or shower area) in Bathroom Zone 0, Zone 1 and Zone 2.
• Protect the power cable from being damaged, do not over stretch cable.
• Only use attachments/accessories specied by the manufacturer Lithe Audio.
• Turn off the power to the speaker when unused for long periods of time.
• A Fire and Acoustic speaker hood must be used in accordance with UK building and IEE
Regulations with a re rating of up to 90 minutes, is Parts B, L, C and E compliant.
• Do not open the back cover to the speaker as this protects the PCB as this will invalidate
the warranty and could cause electric shock.
• Ensure speaker location is free from obstructions such as electrical conduit, HVAC ducts or
Water lines.
PREPARATION EQUIPMENT YOU WILL NEED
BLUETOOTH CEILING
SPEAKER
CUTTING GUIDE SPEAKER CABLE
SCREWDRIVER
MEASURING TAPE
PENCIL
PROTECTIVE EYEWEAR
SPEAKER CABLE
POWER ADAPTOR
CUTTING SAW
DRILL
STUD FINDER
TAPE
WIRE CUTTERS
SPEAKER GRILLE
MODEL LBT1 MODEL LBT2
ALSO INCLUDES
PASSIVE CEILING SPEAKER
BLUETOOTH CEILING SPEAKER
LED COVER
1 2
KNOW YOUR SPEAKER
The LitheAudio LBT range of Bluetooth ceiling wireless speakers have various inputs:
SPEAKER OUTPUT - To connect one additional passive (Slave) speaker (Gold Plated)
RCA INPUTS - To connect directly from CD Player, TV Output, DVD Player etc..
POWER INPUT - To connect (as supplied) transformer
INSTALLATION
IMPORTANT: BEFORE COMMENCING ANY ELECTRICAL WORK ENSURE
THE SUPPLY IS SWITCHED OFF AT THE MAINS. IF YOU ARE UNSURE HOW
TO FIT SEEK HELP FROM A PROFESSIONAL ELECTRICIA /AV INSTALLER
1. Mark out the position of the speaker using a,
tape measure and mark using a pencil with the
template supplied. Check using a stud nder
to make sure no obstruction is present prior
to cutting.
3. Connect the Power lead from the
transformer (supplied) to a 13A mains plug
socket or terminate to a dedicated fused spur.
Ensure the power lead is not overstretched.
2. Drill a pilot hole and cut the speaker hole
using a cutting saw. Take caution when
cutting to keep ngers away from cutting
blade and wear protective eyewear.
4. Insert speaker into the ceiling then using a
screwdriver lock the 4 dog leg xings to secure
the speaker in place, do not over tighten.
Attach the magnetic grille to the speaker front.
Power input 24V/2.5A
RCA-(Black)
R+ (Red) R- (Black)
RCA+(Red)
Speaker output
RCA Input
BLUETOOTH CEILING SPEAKER
Dog leg easy install xings (4)
6.5” (165mm) Kevlar/Polyproplene cone
All models have an in ceiling
depth of 3.8” (95 mm)
Ball joint tweeter to
ne tune direction
Built in Amplier
& Bluetooth driver
Magnets for Cover (8)
Enviromental equalizer
(+/- 3db)
LED indicator
Connection Reset Button
PAINTING THE SPEAKER GRILLE
Do not paint the speaker grilles whilst attached to the speaker. Lithe Audio reccomends spray
painting using 5 parts thinning agent to 1 part paint. Spray thinly to ensure speaker cover grille holes
are not blocked as this will effect the sound quality of the speakers.
INSTALLATIONS IN FIRE-RATED CEILINGS
If you plan to mount your speakers in a re-rated ceiling, you should purchase a re hood for the
speaker. Visit Litheaudio.com for more information.
In built over voltage, under voltage, over temperature, and short circuit protection, if there is an electrical fault,
the power supply to the amplier will cut off automatically and restart when the speaker has stabilised.
3 4
1. Open the setting menu
and select Bluetooth
2. Turn on Bluetooth
and search devices
SETUP AND PAIRING
NOTE: ENSURE THE BLUETOOTH WIRELESS SPEAKER IS CONNECTED TO
THE POWER SUPPLY AND TURNED ON.
The Led indicator will ash Blue/red when ready to pair, turn solid Blue whilst the device is
connected to the speaker and ash blue when music is playing
3. Click Lithe Audio BT and
insert PIN “1234” and click Pair
4. The Lithe Audio Bluetooth
speaker is now connected to your
device ready to play your Music.
CONNECTING DEVICES
If other devices (such as laptops, tablets, phones etc) want to play through the Bluetooth
speakers please follow the steps below:
1. FIRST CONNECTION: If device A connects and controls to Bluetooth, Device B
cannot search or control the Bluetooth speaker. Device A MUST no longer be connected,
then Device B can connect and control.
2. SECOND CONNECTION: If Device A is connected and has control, Device B can’t
connect to Bluetooth until Device A disconnects, enabling Device B to control the
Bluetooth speakers.
3. ADDITIONAL DEVICES: If additional Devices want to connect to Bluetooth speakers,
a maximum of 2 devices can connect at any one time, only the 1st device to connect
controls the speakers. Please ensure devices A or B are disconnected before trying to
connect additional devices C, D, E etc...
NOTE: If your connection to speaker is lost, the device maybe out of range (>10m).
To reconnect simply go to setting menu on the home screen on your device and reconnect to
Litheaudio BT, Bluetooth speaker.
HARD WIRED INPUT- RCA INPUT
To connect other devices that may not have a Bluetooth
connection (such as CD players, BluRay player etc) to play
through the Bluetooth speakers please follow the steps
below:
RCA CONNECTION: To play music via speaker RCA
connection connect an RCA cable to the speaker and play
through your device. Ensure ALL Bluetooth connections are
turned off to be able to play through the speaker.
Image shows Apple iPhone but visuals may change from device to device. Apple and iPhone are trademarks of Apple Inc., registered in the U.S. and other countries.
ADDITIONAL SPEAKER - OPTIONAL
PLEASE NOTE: LBT1 DOES NOT INCLUDE PASSIVE SPEAKER
The Lithe Audio Master Bluetooth ceiling
speaker is able to connect to an addtional
passive speaker via the speaker output (+/-)
Use wire cutters to strip the ends of the
speaker cable (if required).
5 6
TROUBLESHOOTING
If a problem arrises, please try the troubleshooting frequently asked guide below. If the
problem is not listed please contact LitheAudio Customer Service Support.
Q: Speaker has not been found during setup
A: Please check power cord is correctly connected into speaker and transformer, Check the
blue / red light is ashing. Press reset button for 5 seconds to reboot the speaker.
Before commencing any electrical work ensure the supply is switched OFF at the mains.
Q: Speaker has failed to connect to Bluetooth
A: Please retry setup and pairing process, follow setup steps 1 - 4 to connect device. Please
ensure speaker password is entered correctly. Ensure the device is within 10m range.
Q: Device is connected to Bluetooth speaker but no sound
A: Ensure your device volume is NOT muted, increase the volume
Q: Can the speaker be installed into the bathroom ceiling.
A: Only the IP rated models ‘LBT1/IP’ or ‘LBT2/IP’can be installed in zone 3 only. Ensure you
read the saftey precautions on page 1 before installation. Warning: Do not use the product
in water or directly above the bath or shower area.
For further queries and support questions please visit www.litheaudio.com/support
Email: support@litheaudio.com or Call +44 (0) 1293 922 015
REGULATION INFORMATION
EUROPE
LitheAudio declares that this product herewith complies with the requirements of the EMC
Directive 2004/108/EC, Low Voltage directive 2006/95/EC, Eco-Design Directive 2005/32/
EC, RoHS Directive 2011/65/EU and the R&TTE Directive 1999/5/EC when installed and
used in accordance with the manufacturer’s instructions. A copy of the full Declaration of
Conformance may be obtained at www.litheaudio.com/support/policies.
Lithe Audio Speakers have a standby mode or remove the power cord from the AC mains.
RECYCLING INFORMATION
This symbol on the product or on its packaging indicates that this product shall not be treated
as household waste.
Instead please deliver it to the applicable collection point for the recycling of electrical and
electronic equipment. By recycling this product correctly, you will help conserve natural
resources and prevent potential negative environmental consequences. For more detailed
information about recycling of this product, please contact your local council ofce, your
household waste disposal service or the shop where you purchased the product(s) from.
SPECIFICATIONS
• Sound Quality THD+N<0.009%, 65Hz-20kHz
• RMS Power: 50W RMS
• Impedance: 8 Ohms
• Sensitivity (1W/1m): 90dB
• Audio Sample Rate: 8Khz
• Line In Analog (RCA), auto-detecting
• Type: Class D (Digital)
• Woofer: 6.5” Kevlar Woven Cone / Polypropylene
• Tweeter: 1.2” Titanium Cone
• Bluetooth System: Bluetooth V4.0
• Frequency Range: 2.4GHz - 2.4832GHz (ISM Band)
• RF Channels: 79 (USA, Japan & EU)
• Wireless Range: Upto 10 metres
• ID Device Name: Lithe Audio
• Security Passcode: 1234
• Power Input Supply : 100 - 240V ~ / 2A
• Transformer Output Supply : DC24V / 2.5A
• Dimensions (W x D) 6.5 x 3.8 in (230 x 95mm)
• Weight 3.85 lbs. (1.75kg)
• IP rating: IP44 (Model: LBT1/IP or LBT2/IP only)
• Operating Temperature 32º to 104º F (0º to 40º C)
• Storage Temperature 4º to 158º F (-20º to 70º C)
• Standby : 1.3W / 0.02A
• Connected : 1.5W / 0.03A
• Playing Music: 2.8W - 10.5W / 0.03A - 0.09A
**
*
Specications subject to change without notice.
**
Power Consumption depends on the type of music & volume - Increased Bass & volume
requires more power loading on the amplier.
BLUETOOTH CEILING SPEAKER
LED INDICATOR COVER
To mask the LED indicator, use the LED cover sticker included
CONNECTION RESET BUTTON
Press and hold the ‘Reset Button’ for 2 seconds to clear the connection memory.
All paired devices will be deleted.
7 8
This Ceiling Speaker is of excellent quality and construction. However, if any defects in materials
or workmanship do appear during the guarantee period, we will, at our discretion, either repair or
replace the defective parts, free of charge, subject to the terms and conditions of our Guarantee
shown below.
This Guarantee covers both parts and labour. Carriage is not included.
This Guarantee provides benets which are additional to, and do not affect, your statutory rights.
This Guarantee does not cover the cost of returning the product to the dealer from whom it was
purchased or to ourselves. This Guarantee applies only to products sold and located in mainland
Great Britain. It does not cover liability in respect of or replacement of plugs, cables or fuses and
also does not cover defects due to:
• Failure to use or maintain product in accordance with Lithe Audio instructions.
• The product being connected to an unsuitable electricity supply.
• Accidental damage to or abuse or misuse of the product.
• Product modication, except by Lithe Audio or approved agent.
• Dismantling of or interference with the product.
Before returning any product under this Guarantee, please check that:
• You have followed the product instructions correctly.
• Your mains electricity supply is functional.
• The defect is not due to a blown fuse.
If you wish to claim under this guarantee you should:
• Send the product, postage or carriage paid, to the dealer from whom it was purchased or to
Lithe Audio direct.
• Ensure that the product is clean and packed carefully (preferably in its original carton).
• Enclose details of your name, address and telephone number and when and where the product
was purchased, together with proof of purchase (e.g. a invoice or till receipt).
• Give exact details of the nature of the defect.
This Guarantee does not cover any other claims whatsoever, including, without limitation, any
liability for incidental, indirect or consequential damage, nor does it cover any claims for conversion
or modication or for the costs of repair carried out by any third party without the prior consent
of Lithe Audio. If replacement parts are tted to the product this will not extend the period of the
Guarantee. For further advice contact the Lithe Audio customer services.
WWW.LITHEAUDIO.COM
TEL: 01293 922 015 EMAIL: INFO@LITHEAUDIO.COM
LBTIBGBA
2 YEAR GUARANTEE
Lithe Audio products marked with the CE mark comply with the EC Low Voltage
Directive: 73/23/EEC, Electromagnetic Compatibility Directive 89/336/EEC
Loading...