This document contains confidential proprietary information and is property of LTC. The contents of this document
should not be disclosed to unauthorized persons without the written consent of LTC.
Liteon semi-P/N:
Change History:
Revision Date Author Change List
Draft 2010/07/12 Kenny Su Preliminary
Version 1.0 2011/05/18 Kenny Su Add PCBA Mechanical
Ver sion 1.1 2011/08/26 Kenny Su Revise Product Feature
B853HZ100G
Author: Kenny Su Approved by: Alfred But
Editor: Kenny Su Project Leader: Alfred But
Less than 1mSec latency between video source and video sink
Static Video Recognition
High Definition Interface:
36-bit RGB or YCrCb (4:4:4)
Enables the support of non-standard resolutions
Audio:
Up to 18 Mbps throughput of audio stream
I²S: Up to eight PCM channels
SPDIF: Including AC-3, DTS HD, Dolby 5.1, Digital
RoHS
WV301A Specification Page 4/11 2011/08/26
LTC Network Access Confidential
MAIN CHIPSET
Amimon AMN2220 + AMN3210
FUNCTIONAL SPECIFICATIONS
WHDI Function
Standard
Bus Interface
Data Rate
Modulation Scheme
Frequency Range
Operating Voltage
Security
Power Consumption
Antenna Type
WHDI 1.0
HDMI
20MHz UL (Rx to Tx): Up to 30.0 Kbps
40MHz UL (Rx to Tx): Up to 60.0 Kbps
Uses 18MHz or 40Mh z bandwidth and is ca rried over the
5GHz unlicensed band
5150~5250;5725~5850MHz
5 V ±5% supply voltage
128/256-bit AES based encryption
7.5Watt – 1080P
Five PCB antennas
WV301A Specification Page 5/11 2011/08/26
LTC Network Access Confidential
PCBA MECHANICAL
WV301A Specification Page 6/11 2011/08/26
LTC Network Access Confidential
LED BEHAVIOR
Indication Function
LED1 Link On/Off
LED2 Power On/Off
LOCK DIAGRAM
B
ENVIRONMENTAL
Operating
O perating Temperature: 10-35ºC ambient in still air (outside of case)
Relative Humidity: 5-90% (non-condensing)
Storage
Temperature: -20 to 70 C
Relevant Humidity: 5-95% (non-condensing)
WV301A Specification Page 7/11 2011/08/26
LTC Network Access Confidential
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
– Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
RF exposure warning ·
This equipment must be installed and operated in accordance with provided instructions and
the antenna(s) used for this transmitter must be installed to provide a separation distance of
at least 20cm from all persons and must not be co-located or operating in conjunction with
any other antenna or transmitter. End-users and installers must be provided with antenna
installation instructions and transmitter operating conditions for satisfying RF exposure
compliance.
WV301A Specification Page 8/11 2011/08/26
LTC Network Access Confidential
Canada, Industry Canada (IC) Notices
This Class B digital apparatus complies with Canadian ICES-003 and RSS-210.
Operation is subject to the following two conditions: (1) this device may not cause interference,
and (2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Radio Frequency (RF) Exposure Information
The radiated output power of the Wireless Device is below the Industry Canada (IC) radio
frequency exposure limits. The Wireless Device should be used in such a manner such that
the potential for human contact during normal operation is minimized.
This device has also been evaluated and shown compliant with the IC RF Exposure limits
under mobile exposure conditions. (antennas are greater than 20cm from a person's body).
This device has been certified for use in Canada. Status of the listing in the Industry
Canada’s REL (Radio Equipment List) can be found at the following web address: