Federal Communication Commission Interference Statement
r
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications n ot expressly approved by the party resp on sible f or complia nce coul d void
the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance 20cm between the radiator & your body.
This module is intended for OEM integrators under the following conditions:
This module comply with the requirement of the following standards
47 CFR FCC Part 15.247
1. RF exposure considerations
This module is restricted to installation in products for use only in mobile and fixed applications.
The host product manufacturer must provide following statement in end-product manuals.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance 20cm between the radiator & your body.
2. Antennas
This module has been approved to operate with the antenna types listed below, with the maximum permissible gain
indicated.
Ant. Brand Model Name Antenna Type Connecto
Gain (dBi)
1 Walsin RFDPA870900SBAB815 Dipole I-PEX 2.3
2 Walsin RFPCA431015IMAB301 PIFA I-PEX 2.69
3 Walsin RFDPA131015IMRB301 Dipole I-PEX 3.01
4 Walsin RGFRA1204011DCT Chip I-PEX 1
5 Ethertronics M620720 Chip I-PEX 0.75
6 TEKFUN IO4-2 Dipole I-PEX 1.2
3. Label and compliance information
The host product must be labeled in a visible area with the following " Contains FCC ID: PPQ-WSG309S ".
The end product shall bear the following 15.19 statement: This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired operation.
4. Additional testing, Part 15 Subpart B disclaimer
Appropriate measurements (e.g. 15 B compliance) and if applicable additional equipment authorizations (e.g.
SDoC) of the host product to be addressed by the integrator/manufacturer.
This module is only FCC authorized for the specific rule parts 15.247 listed on the grant, and the host product
manufacturer is responsible for compliance to any other FCC rules that apply to the host product as being Part 15
Subpart B compliant.
5. The user manual of the end product should include
- Any changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate this equipment.
- The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm
from all persons.
- This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
- This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or
transmitter.
Loading...