User MANUAL
802.11b/g/n 2Tx2R + BT5.0 USB
WLAN Module
Model Name: WCBN4606L
Brand: LITE-ON
Page 1/15
CONTENT
PRODUCT FEATURES ....................................................................................................................7
BT FEATURE:.........................................................................................................................................7
WI-FI FEATURE:.....................................................................................................................................7
PRODUCT SPECIFICATIONS........................................................................................................8
MAIN CHIPSET .......................................................................................................................................8
FUNCTIONAL SPECIFICATIONS ...............................................................................................................8
RECOMMENDED OPERATION CONDITIONS........................................................................11
DC CHARACTERISTICS...............................................................................................................11
RESET TIMING SPEC....................................................................................................................11
PIN ASSIGMENT.............................................................................................................................12
USB CONNECTOR SPEC...............................................................................................................12
MECHANICAL ................................................................................................................................13
I-PEX CONNECTOR SPEC............................................................................................................14
MODULE PHOTO...........................................................................................................................15
EEPROM INFORMATION ............................................................................................................15
WI-FI/BT.............................................................................................................................................15
ENVIRONMENTAL........................................................................................................................15
OPERATING..........................................................................................................................................15
STORAGE..............................................................................................................................................15
Page 2/15
Page 3/15
FCC Statement:
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one of the following
measures:
- Reorient or relocate the receiving antenna. - Increase the separation between the equipment
and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
˗Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of
other channels is not possible. This device and its antenna(s) must not be co-located with any
other transmitters except in accordance with FCC multi transmitter product procedures. Referring
to the multi transmitter policy, multiple transmitter(s) and module(s) can be operated
simultaneously without C2PC.
IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC
radiation exposure limits set forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 20 cm between the radiator & your body.
IMPORTANT NOTE: This module is intended for OEM integrator. The OEM integrator is
responsible for the compliance to all the rules that apply to the product into which this certified
RF module is integrated. Additional testing and certification may be necessary when multiple
modules are used.
Page 4/15
20 cm minimum distance has to be able to be maintained between the antenna and the users for
the host this module is integrated into. Under such configuration, the FCC radiation exposure
limits set forth for an population/uncontrolled environment can be satisfied.
Any changes or modifications not expressly approved by the manufacturer could void the user's
authority to operate this equipment.
USERS MANUAL OF THE END PRODUCT:
In the user’s manual of the end product, the end user has to be informed to keep at least 20 cm
separation with the antenna while this end product is installed and operated. The end user has to
be informed that the FCC radio frequency exposure guidelines for an uncontrolled environment
can be satisfied. The end user has to also be informed that any changes or modifications not
expressly approved by the manufacturer could void the user's authority to operate this
equipment. If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19
statement is required to be available in the user’s manual: This device complies with Part 15 of
FCC rules. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference and (2) this device must accept any interference received, including
interference that may cause undesired operation.
LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains FCC ID:
PPQ-WCBN4606L ". If the size of the end product is larger than 8x10cm, then the following FCC
part 15.19 statement has to also be available on the label: This device complies with Part 15 of
FCC rules. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference and (2) this device must accept any interference received, including
interference that may cause undesired operation.
OEM Integrator Checklist
The party below will implement the LITE-ON Module in host systems in accordance with the
instructions specified in this document and the documents referenced herein.
1.The OEM integrator will ensure the Module is integrated in a host systems using only the
approved antenna model(s) described in this document.
2.The OEM integrator will ensure the antenna placement inside the host system willmaintain the
required spacing to end user for RF Exposure compliance, as specified in this document. 3.If other
radios are integrated inside the host with the LITE-ON Module, the OEM integrator will contact its
test lab, TCB or LITE-ON to determine if additional FCC compliance evaluation is required to meet
FCC collocation rules.
4.The OEM integrator will ensure end user documentation will contain the specified regulatory
wording and ensure the host system and the Module itself are labeled as specified in this
document.
Page 5/15
5. The OEM integrator will ensure the Module is programmed in the factory with compliant
transmit power not exceeding the levels specified in this document. LITE-ON requests that the
OEM integrator acknowledge its receipt of this document and the above instructions. You may
contact LITE-ON with any questions concerning this document or the responsibilities of the OEM
integrator
Page 6/15
PRODUCT FEATURES
BT FEATURE:
Bluetooth V5.0 system
Backwards compatible with BT version of 1.1, 1.2, 2.0, 2.1, 3.0+HS and 4.0LE
Bluetooth Class I transmission power
Support all packet types in basic rate and enhance data rate
Support Secure Simple Pairing
Support multiple low energy states
Fast AGC control to improve receiving dynamic range
Support Wake On Bluetooth
WI-FI FEATURE:
Operate at ISM frequency Band (2.4GHz)
IEEE Standards Support, 802.11b, 802.11g, 802.11n
Support for both 20 MHz, 40MHz channel width in 2.4GHz band
Enterprise level security supporting: WAPI, WPA, WPA2
Support 2 transmission and 2 receiving, transmission rate can up to 300Mbps
(Physical Rate) in downstream and upstream
QoS support of WFAWMM, WMMPS
Wi-Fi Direct support wireless peer to peer application
Channel management and co-existene
Support Wake On WLAN via Magic packets and wake-up frame
RTL8725A is a single chip integrated IEEE 802.11 b/g/n and Bluetooth 5.0 with
a single USB interface
Enhanced BT/WI-FI coexistence control to improve transmission quality in
different profiles
Fully compliance with USB v2.0 specification
RoHS compliance
Low Halogen compliance
Page 7/15
PRODUCT SPECIFICATIONS
MAIN CHIPSET
Realtek RTL8725A
FUNCTIONAL SPECIFICATIONS
BT Function
Standard
Bus Interface
Data Rate
Modulation Scheme
Frequency Range
Transmit Output Power
Receiver Sensitivity
Wi-Fi Function
Standard
Bus Interface
Data Rate
Bluetooth V5.0LE
USB2.0
1 Mbps, 2Mbps and Up to 3Mbps
GFSK, π/4-DQPSK and 8-DPSK
2.402~2.480 GHz
+4 ≤ Output Power ≤ +10dBm; Class I Device
< 0.1% BER at -88dBm
IEEE802.11b; IEEE 802.11g; IEEE 802.11n.
USB2.0
802.11b:
11, 5.5, 2, 1 Mbps
802.11g:
54, 48, 36, 24, 18, 12, 9, 6 Mbps
802.11n:
MCS 0 to 15 for HT20MHz
MCS 0 to 15 for HT40MHz
Media Access Control
Modulation Technique
Network Architecture
Operation Channel
Frequency Range
EVM
CSMA/CA with ACK
802.11b:
CCK, DQPSK, DBPSK
802.11g:
64QAM, 16QAM, QPSK, BPSK
802.11n:
64QAM, 16QAM, QPSK, BPSK
Ad-hoc mode (Peer-to-Peer)
Infrastructure mode
2.4GHz
11: (Ch. 1-11) – United States
13: (Ch. 1-13) – Europe
14: (Ch. 1-14) – Japan
802.11bg
2.400 ~ 2.4835 GHz
CCK < 35%
OFDM < -25dB
MCS0(HT20/40MHz) < -5dB
Page 8/15
MCS7(HT20/40MHz) < -28dB
, IEEE
MCS0(VHT20/40/80MHz) < -5dB
MCS7(VHT 20/40/80MHz) < -27dB
Frequency Offset
2.4GHz
-20ppm < Center Frequency < +20ppm
Transmit Output Power - single chain @ant;
Tolerance: ±1.5dBm@2.4GHz
802.11b 1Mbps 2Mbps 5.5Mbps 11Mbps
Tgtpwr
17 17 17 17
(dBm)
802.11g 6~24Mbps 36Mbps 48Mbps 54Mbps
Tgtpwr
17 16 16 16
(dBm)
802.11n
MCS0 MCS1 MCS2 MCS3 MCS4
HT20
Tgtpwr
16 16 16 15 15
(dBm)
MCS5 MCS6 MCS7 MCS8 MCS9
14 14 14
802.11n
MCS0 MCS1 MCS2 MCS3 MCS4
HT40
Tgtpwr
16 16 16 15 15
(dBm)
MCS5 MCS6 MCS7 MCS8 MCS9
14 14 14
Receiver Sensitivity
Frequency
Rate Condition Typical (1SS)
Band
11b-1M PER < 8% -94
11b-11M PER < 8% -86
11g-6M PER < 10% -90
2.4G
11g-54M PER < 10% -71
11n-HT20MCS0 PER < 10% -87
11n-HT20MCS7 PER < 10% -70
11n-HT40MCS0 PER < 10% -84
11n-HT40MCS7 PER < 10% -67
Security
(dBm)
WPS, WPA, WPA2, WEP 64bit & 128bit, IEEE 802.1X
802.11i
Common Function
Operating Voltage
5V ±10% I/O supply voltage
Page 9/15
Mode Average Peak
Power Consumption
Antenna Type
TX
RX
Unassociated
442mA 829mA
185mA 796mA
31mA
Idle
Standby for
37mA
Wake up mode
2x Metal Antennas for WiF; 1x U.FL connectors for BT
Page 10/15
RECOMMENDED OPERATION CONDITIONS
Symbol Rating Min Typ Max Units
+5VCC 5V Supply Voltage 4.5 5 5.5 V
VDD33_USB
VA33X
VR33_SYN
VR33_RTX_S0
3.3V Supply Voltage 3.0 3.3 3.6 V
VR33_RTX_S1
BT_BD33PA
VD33_SPS
VA10_AFE
VA10_SYN
VR10_RTX_S0
VR10_RTX_S1
1.05V Core Supply Voltage 1.15 1.25 1.37 V
VD10D
VA10_USB
VDD12BT
BT_VD12RTXBB
BT_BD12RTXFE
1.2V Supply Voltage 1.08 1.2 1.32 V
BT_VD12SYN
DCCHARACTERISTICS
Symbol Parameter Min Typ Max Units
V
IL
V
IH
V
OL
V
OH
Input Low Voltage - 0 0.9 V
Input High Voltage 2.0 3.3 3.63 V
Output Low Voltage 0 - 0.33
Output High Voltage 2.97 - 3.3 V
RESET TIMING SPEC
Symbol Min Typ Max Units
T
on
T
POR
Noted: Reset time
0.2 1.5 5 ms
- 2 10 ms
不需要特別定義時間,只要確定有拉起來即可
Page 11/15
PIN ASSIGMENT
Pin. Pin Define Description Status
1
2
3
4
5
6
7
8
9
10
+5V 5V source
+5V 5V source
USB_D- USB DataUSB_D+ USB Data+
GND Ground
RESET# Systemreset RTL8192FC, low active
WoWLAN# Wake up system via wifi, low active
GND Ground
WoBT Wake up system via BT, high active
GND Ground
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
USB CONNECTOR SPEC
Manufacture P/N: S1315-10RVB-SB3-KH
Thickness of gold flash printed: ≥1u”
Page 12/15
MECHANICAL
Weight: 3.6g
Page 13/15
I-PEX CONNECTOR SPEC
Page 14/15
MODULE PHOTO
Front Side
Bottom Side
EEPROMINFORMATION
WI-FI/BT
Reg Domain
Vendor ID
Device ID
ENVIRONMENTAL
OPERATING
Ambient Operating Temperature: 0 to 70 C (32 to 158 F)
Ambient Relative Humidity: 5-90% (non-condensing)
STORAGE
Ambient Temperature: -40 to 80 C (-40 to 176 F)
Ambient Relative Humidity: 5-95% (non-condensing
World Wide
2.4G
Read from registry; Control by driver
0x7F
0x0BDA
0xA725
Page 15/15
Loading...