LITE ON TECHNOLOGY WCBN3514A User Manual

PRODUCT SPECIFICATION

Wi-Fi (11a/b/g/n/ac 2Tx2R)+BT (V4.2LE) SDIO Combo Module

WCBN3514A

User Manual

Page 1/19

CONTENT

DESCRIPTION ................................................................................................................................... 9

PRODUCT FEATURES .................................................................................................................... 9

PRODUCT SPECIFICATIONS ...................................................................................................... 10

MAIN CHIPSET ..................................................................................................................................... 10

FUNCTIONAL SPECIFICATIONS ............................................................................................................. 10

RECOMMENDED OPERATION CONDITIONS ........................................................................ 13

PIN ASSIGMENT ............................................................................................................................. 13

MECHANICAL ................................................................................................................................ 15

FOOTPRINT ..................................................................................................................................... 15

MODULE PINOUT .......................................................................................................................... 16

BLOCK DIAGRAM ...................................................................................... 錯誤! 尚未定義書籤。

MHF4 CONNECTOR SPEC ........................................................................................................... 17

POWER-UP SEQUENCE TIMING ............................................................................................... 18

EEPROM INFORMATION ............................................................................................................ 19

BT ........................................................................................................................................................ 19

WI-FI ................................................................................................................................................... 19

ENVIRONMENTAL ........................................................................................................................ 19

OPERATING .......................................................................................................................................... 19

STORAGE .............................................................................................................................................. 19

Page 2/19

FCC Statement:

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interference by

one of the following measures:

˗ Reorient or relocate the receiving antenna.
˗ Increase the separation between the equipment and receiver.
˗ Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.
˗Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.

For product available in the USA/Canada market, only channel 1~11 can be operated.
Selection of other channels is not possible.
This device and its antenna(s) must not be co-located with any other transmitters except in
accordance with FCC multi transmitter product procedures.
Referring to the multi transmitter policy, multiple transmitter(s) and module(s) can be
operated simultaneously without C2PC.

IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20 cm
between the radiator & your body.

Page 3/19

IMPORTANT NOTE:

This module is intended for OEM integrator. The OEM integrator is responsible for the

compliance to all the rules that apply to the product into which this certified RF module is
integrated.

Additional testing and certification may be necessary when multiple modules are used.

20 cm minimum distance has to be able to be maintained between the antenna and the users
for the host this module is integrated into. Under such configuration, the FCC radiation
exposure limits set forth for an population/uncontrolled environment can be satisfied.

Any changes or modifications not expressly approved by the manufacturer could void the
user's authority to operate this equipment.

USERS MANUAL OF THE END PRODUCT:

In the users manual of the end product, the end user has to be informed to keep at least 20

cm separation with the antenna while this end product is installed and operated. The end

user has to be informed that the FCC radio frequency exposure guidelines for an uncontrolled

environment can be satisfied. The end user has to also be informed that any changes or

modifications not expressly approved by the manufacturer could void the user's authority to

operate this equipment. If the size of the end product is smaller than 8x10cm, then additional

FCC part 15.19 statement is required to be available in the users manual: This device complies

with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device

may not cause harmful interference and (2) this device must accept any interference received,
including interference that may cause undesired operation.

LABEL OF THE END PRODUCT:

The final end product must be labeled in a visible area with the following " Contains TX FCC ID:

PPQ- WCBN3514A ". If the size of the end product is larger than 8x10cm, then the following

FCC part 15.19 statement has to also be available on the label: This device complies with Part

15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference and (2) this device must accept any interference received,
including interference that may cause undesired operation.

OEM Integrator Checklist

The party below will implement the LITE-ON Module in host systems in accordance with the
instructions specified in this document and the documents referenced herein.

1. The OEM integrator will ensure the Module is integrated in a host systems using only the

approved antenna model(s) described in this document.

2. The OEM integrator will ensure the antenna placement inside the host system will

Page 4/19

maintain the required spacing to end user for RF Exposure compliance, as specified in this
document.

3. If other radios are integrated inside the host with the LITE-ON Module, the OEM

integrator will contact its test lab, TCB or LITE-ON to determine if additional FCC
compliance evaluation is required to meet FCC collocation rules.

4. The OEM integrator will ensure end user documentation will contain the specified

regulatory wording and ensure the host system and the Module itself are labeled as
specified in this document.

5. The OEM integrator will ensure the Module is programmed in the factory with compliant
transmit power not exceeding the levels specified in this document.

LITE-ON requests that the OEM integrator acknowledge its receipt of this document and the

above instructions. You may contact LITE-ON with any questions concerning this document or

the responsibilities of the OEM integrator.

IC Statement:

This device complies with Industry Canada license exempt RSS standard(s). Operation is

subject to the following two conditions: (1) this device may not cause interference, and (2)

this device must accept any interference, including interference that may cause undesired

operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio

exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil

ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout

brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le

fonctionnement.

For product available in the USA/Canada market, only channel 1~11 can be operated.
Selection of other channels is not possible.

Pour les produits disponibles aux États Unis / Canada du marché, seul le canal 1 à 11 peuvent

être exploités. Sélection d'autres canaux n'est pas possible.

This device and its antenna(s) must not be co-located with any other transmitters except in
accordance with IC multi transmitter product procedures.

Referring to the multi transmitter policy, multiple transmitter(s) and module(s) can be
operated simultaneously without reassessment permissive change.

Cet appareil et son antenne (s) ne doit pas être co-localisés ou fonctionnement en association

avec une autre antenne ou transmetteur.

The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the

Page 5/19

potential for harmful interference to co-channel mobile satellite systems.

les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour

une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes

de satellites mobiles utilisant les mêmes canaux.

The maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such
that the equipment still complies with the e.i.r.p. limits specified for point-to-point and
Non-point-to-point operation as appropriate.

le gain maximal d’antenne permis (pour les dispositifs utilisant la bande 5725-5850 MHz)

doit se conformer à la limite de p.i.r.e. spécifiée pour l’exploitation point à point et non-point

à point, selon le cas.

Dynamic Frequency Selection (DFS) for devices operating in the bands 5250- 5350 MHz,

5470-5600 MHz and 5650-5725 MHz.

Sélection dynamique de fréquences (DFS) pour les dispositifs fonctionnant dans les bandes

5250-5350 MHz, 5470-5600 MHz et 5650-5725 MHz.

The maximum antenna gain permitted for devices in the bands 5250-5350 MHz and
5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit.
le gain maximal d’antenne permis pour les dispositifs utilisant les bandes 5250-5350 MHz et

5470-5725 MHz doit se conformer à la limite de p.i.r.e.

Users should also be advised that high power radars are allocated as primary users (i.e.

priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could

cause interference and/or damage to LE•LAN devices.

De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute

puissance sont désignés utilisateurs principaux (c.•à•d., qu’ils ont la priorité) pour les bandes

5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou

des dommages aux dispositifs LAN•EL.

Pour une utilisation en intérieur uniquement.

Page 6/19