I N S TA L L AT I O N
>
HOW TO MOUNT THE PND-K3.
1
Find a spot suitable for the navigation device. Stick the
suction cup against the desired mounting location. Press
the lever to secure the suction cup.
PND
Portable Navigation System
Q U I C K R E F E R E N C E G U I D E
-
K3
2
Guide the navigation device onto the cradle.
Gently push until a click sound is heard and the device is
3
locked in place.
>
HOW TO REMOVE THE PND-K3.
Press on the button immediately behind the navigation
1
device. This will release the unit forward. Gently lift the
device from its cradle.
C O N T R O L S
>
PRIMARY BUTTON CONTROLS
M A I N M E N U
POWER
Press and hold for 2 seconds
to turn on/off the device.
SD CARD SLOT
For music playback.
HEADPHONE JACK
VOLUME DOWN
VOLUME UP
“GO TO” BUTTON
Press this to start entering
a destination.
“HOME” BUTTON
Press this to go to a saved
home location.
“PLAY” BUTTON
Press this to go to the
music player.
“INFO” BUTTON
Press this to check
information such as:
• GPS receiver status
• Speed and trip information
“SETTINGS” BUTTON
Press this to change
system settings.
“MAP” BUTTON
Press this to go to the
map.
M A P
R O U T E M E N U
>
MAP WITHOUT GUIDANCE
Changes map view
(2D, 3D)
>
MAP WITH GUIDANCE
Press to repeat voice
guidance
Press to view route
menu (see next page)
Goes back to Main
Menu screen.
Zooms Map View In
Zooms Map View Out
Goes back to Main
Menu screen.
Zooms Map View In
Zooms Map View Out
Change navigation mode
to arrow only mode
>
THE ROUTE MENU ALLOWS YOU TO EASILY MODIFY OR CA NCEL
ROUTING TO A DESTINATION.
Press to view list of
upcoming manuevers
Press to change route options
(shortest, quickest, etc)
Cancel the current route
Press to calculate a
detour route
Press to add or reorder
waypoints
Changes map view
(2D, 3D)
R E A L LY C O O L F E A T U R E S
R E A L LY C O O L F E A T U R E S
>
CHOOSE YOUR FAVORITE COLOR
Select “Display” from the settings menu to change your color scheme.
>
POINTS OF INTEREST ALONG ROUTE
Want to find a restaurant on the way home? This option finds only Points of
Interest (POI) that are on the way to your current destination.
>
POINTS OF INTEREST KEYWORD SEARCH
Don’t know the full POI name? Type in what you know and find relevant
results. This search method returns place names containing, and not
necessarily beginning with, the search term.
K3 Hardware Specification Version 0.2
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
– Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
Any changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
FCC RF Radiation Exposure Statement
This equipment must be installed and operated in accordance with provided instructions and the
antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm
from all persons and must not be co-located or operating in conjunction with any other antenna or
transmitter. End-users and installers must be provide with antenna installation instructions and
transmitter operating conditions for satisfying RF exposure compliance.
Lite-On Tech. Corp. Confidential Page 61 of 61
Document Editor
Jeff Cheng /Binson Chien /Allen Wong/Jamie Chen
2007/5/
Loading...