Litele LC User Manual

Download

LC SERIES

USER MANUAL FOR CCD

BARCODE READER

LC SERIES

USER MANUAL FOR CCD

BARCODE READER

Perface:

Thanks for purchasing our Litele LC-series CCD (Charge-Coupled Device) Barcode Scanner. LC-Series CCD barcode scanner apply all the advanced technologies that a CCD could have. Its superior scan engine provides quick scanning w ith reliable successful first read rate. The scanner is programmable and ideal for Poi nt Of Sal e (POS) and docume nt trac king applications.

With the built-in decoder, Litele LC-Series CCD can recognize and decode most of the standard barcode, such as EAN -8/JAN-8, EAN-13/JAN-13, UPC A/E, full ASCII Code 39, Code 39, Interleaved 2 of 5, Code 93, EAN-128, Matrix 2 of 5 and Chinese Post Code, etc. The scanner can be used with computers that have standard keyboard, RS /232 or USB interface, as well as ot her devices that have standard communication interface.

Wit h the purchasing, you get not only the product, but al so the instant professional technical support offered by our product service center and dealers.

Ver. 2.4

The manual is applied to Litele LC-series CCD bar code scanner, with hardware version 2.4.

P/N: 82010-24E

Features:

vBuilt-in dec oder allows automatic recogni-

tion and dec oding of most popular barcodes.

vScanning speed up to 100 scans/sec . vObviou s read LED indicator and nice tone

beepe r.

vMultiple c ommunication interfaces to

choose: USB,RS-232, AT/XT , PS/2 Keyboard Emulation .

vSuperior optical pe rformance with a mini-

mum r esolution of 0.127mm (5 mils).

vUp to 80mm width scanning window. vScanning by touchin g/approaching the

labe ls (The maximum reading distance for LC-80 Ser ial is 20mm, for LC-90 Serial is 180mm).

vWith “Y” Wedge Keyboard Cable, you can

use scanner and keyboard t he same time.

vDurable trigge r button with different mode

to choose: * Tridgger Mode * Auto Scan Mode

Warning

Incorrect operation may damage or dedu ct the lifetime of th e Scanner. Please read this manual carefully before you connect the scanner to the comp uter.

Please make sure the computer pow er is off before you connect or dis connect the CCD Scanner with the computer (Exception: US B interface).

Other devices (except keyboard) are not allowed to connect with “Y” w edge cable when you are using LC

-Series CCD barcode KB s canner.

LC-series CCD RS-232 type scanners should not be used w ith computers without the special external DC power supply.

Please pow er off and disconnect it immediately in case the scanner is broken and the inner parts w ere exposed.

Please power off and disconnect it immediately to avoid burn or fire in case you found high temperature, smoke or stimulating smell happened to the scanner.

Don’t disassemble the scanner by yourself, Please contact our service center w hen it need to be opened.

CATALOG

Components.........................................1

Apperance & Parts name.......................1

Installation........... .................................2

Usage.. ................................................2

Parameter Se tting Flow Chat .................5

Common Q & A............. ........................4

System Setting......................................6

Scanning Mode Selection........................7

Output Device.........................................8

RS-232C serial communication

parmeters setting....................................8

Beeper Tone Selection ...........................11

Keyboard parameters setting .................12

Keyboard emulation parameters

Setting........ .........................................12

Inter-Message Delay .............................14

Inter-Character Delay .............................15

CODE 39 Parameters Setting ................15

CODEBAR Parameters Setting...............16

UPC/EAN Parameters Setting ................16

ISSN/ISBN Conversion............ ...............14

Reading Code Selection .........................19

Header and Trailer..................................22

Code Length Selection............................23

Bar code Identifier Code Selection...........25

Appendix.. ............................................28

Component

The following components will be found in the product package For LC-80K B, including: Scanner, User Manual For LC-80RS, including: Scanner, User Manual (Pow er Adapter) For LC-80U SB, including: Scanner, User Manual For LC-90K B, including: Scanner, User Manual For LC-90RS, including: Scanner, User Manual (Pow er Adapter) For LC-90U SB, including: Scanner, User Manual

Appear ance with parts name:

TOP View

Indicator

Shell

Back View

Button

Cable

Rubber Shield

Scan Window

Installation:

Installation of LC-80/90 KB Scanner

1. Make sure the Power of the computer is off;

2. Unplug the keyboard;

3. Connect the scanner cable (“Y” - Wedge Cable)

with the computer;

4. Connect the keyboard to the s canner cable (“Y”

- Wedge Cable);

5. Turn on the computer; the scanner will start to

w ork.

Installation of LC-80/90 US B Scanner

1. Connect the scanner USB cable with the com-

puter USB Port;

2. The scanner will start to w ork right away if the

computer is on. Please note: the USB KEYBOARD port should set as Enabled in BO IS Setting.

Installation of LC-80/90 RS Scanner

1. Make sure the pow er of the device is off;

2. Connect the scanner cable with the Serial Port;

3. (Plug in and connect the pow er cable to the

scanner)-- This step needed only when connect

with computer

4. Turn on the device; the scanner will start to

w ork.

Usage:

This product is used to scanning one-dimensional Barcode. When you scanning, the scanning window should be faced to the barcode. The red light will show up from the window when you push the button, adjust the dista nce between barcode and the scanning window (M aximum 20 mm for LC 80, 180mm for LC 90). Please ensure the barcode is all covered with the red light. The scanner will indicate the successful reading by a short beep and the same time a red flas hing from the

indicator.

Notes:

tThe barcode symbol shall be put in the center of

red light.

tOnly one barcode can be read each time, i.e. only

one barcode can be fully put within the red light.

tStrong light environment w ill reduce the barcode

readability.

tSmutched barcode symbol will reduce the barcode

readability.

tThe cable cannot be pulled with a strong strength. tThe barcode can be read only when the barcode

symbol has a certain height.

Setting:

LC - Series Barcode scanner is programmable. Sc anning a series of programming bar code labels can co nfigure the scanners. This allows Encoding Opti ons and Interface Protocols to be tailored to a specific ap plication. The configuration is stored in non -volatile memory and will not be lost by remov-

ing pow er from the scanner. Du ring the programming mode, the scanner will ackn owledge a good and valid reading with speciafic music(c ertain tone of beeps). Long sharp beeps will p rovided for either an invalid or bad re ading.

Please followed th e Configuration Flow Chat to set up you r CCD Barcode Scanner

Parameters Setting Flow Chat

Sta rt

Scan Barcode “Start of Configuration”

Sca n Barcode Settings (i.e.: “RESET TO ORIGINAL”, “BEEPING TONE — LOW”… )

Scan barcode “End of Configration”

End

Finish Se tting?

Ye s

No?

Common Q & A

Problem Description

Diagnosis Solution

The scanner

does not

respose when the

device/computer

power on

The interface of host is damaged.

Replace the host interface.

The connecting

cable is damaged.

Check the cable,

repaired if damaged.

The scanner is damaged.

Send to the service center for repair.

The power supply of the serial interface

scanner is not connected

well or is damaged.

Connect the power supply again or

replace the power

supply.

Can not

recoganize /decode barcode

Check if the barcode

format is in the readable range of this barcode and the mode is set as "on"

Set according to the setting manual.

The scanner is too close to the barcode symbol.

Move further.

The length of the barcode

symbol exceeds the

range of red light.

Scale down the

barcode symbol.

Hard to recoganize /decode barcode

The surface of the barcode symbol is

damaged or smutched.

Manually input with keyboard.

The glass of the scanning window is dirty.

Clean the scanning

window glass.

The light of the

environment is too strong.

Change the working environment

No show up on the screen after.

scanning and

beeping

The interface mode or

communication

parameter is not correct.

Set according to the setting manual.

The cable is working well.

Replace/repair the

cable line.

Start of Confi guration

System Parameters

RESET

The reading of the “RESET” Label turns all the parameters back to default values.

ABORT

The reading of the “ABORT” label discards all the parameters read prior to the “EXIT(Start of Configuration)”.

START

Start setting (Start of Configuration)

EXIT

SET

Ignore all code system

Show Version

Show the hardware version.

Ignore

Exit setting (End of Configuration)

Confirm input

End of Configuration

Scann ing Mode Selection

Trigger

The scan ner becomes inactive as soon as the data is transmitted. It must be triggered to become acti ve

again.

Turbo Trigger

The scan ner switch is pressed and double reading for the same bar code is not permitted. The scanner will be inacti ve after the switch is released.

Auto Scan

In auto scan mode, the scanner i s still active after th e data is transmitted, but the successive transmi ssion of the same bar code

is n ot allowed.

Alt

This scanner w ill light up when press the scanner trigger switch once.And,the scanner wi ll turn off

for next pressing.

Testing

For factory testing use only

Start of Confi guration

OU TPUT DEVICE

RS 232-C

Key Board

US B

RS-23 2C SERIAL COMMUNICATION PARAMETERS SETTING

BAUD RATE

19200

4800

2400

9600

End of Configuration

1200

600

DATA BIT

STOP BIT

PARITY

EVEN

ODD

Start of Confi guration

MARK

NONE

SPACE

SERI AL PORT MESSAGE TERMINATOR

NONE

CR/LF

HTAB

End of Configuration

STX/ETX

EOT

GOOD READ BEEPER TONE

Medium

Low

High

Disable

Start of Confi guration

SOUN D DURATION

Long

Medium

Short

Very Short

MESSAGE TERMINATIOR(FOR KEYBOARD)

None

CR/LF

TAB

End of Configuration

KEYBOAR D EMUL ATION PARAMETERS SETTIN G

IBM AT

PS /2 30-80

IBM 5550

IBM 5295 Terminal

IBM XT

IBM 3477

IBM 5530-SC

Start of Confi guration

IBM 5530-ZC

NEC 9801

IBM 3196 Terminal

Apple MAC

MOS_SYS

PS2/30/56

IBM 3477 Terminal (Without break code)

NEC 5200

End of Configuration

MESSAGE DELAY

NONE

100msec

500msec

1 Second

CHAR DELAY

NONE

10msec

20msec

50msec

Start of Confi guration

CODE 39 PARAMETERS SETTING

STANDARD CODE 39

FULL ASCII CODE 39

CHECK DIGIT

Calculate and Transmit

NO CHECK DIGIT

Calculate but not Transmit

ITF 2 OF 5 PARAMETERS SETTING

Calculate but not Transmit

NO CHECK DIGIT

Calculate and Transmit

End of Configuration

CODABAR PARAMETERS SETTING

A,B,C,D

A/T, B/N, C/*, D/E

DC1~DC4

UPC/EAN PARAMETERS SETTING

UPC-E=UPC-A

Disable

Enable

UPC-A=EAN-13

Disable

Enable

Start of Confi guration

UPC-A LEADING CHARACTER

Disable

Enable

UPC-A CHECK DIGIT

Disable

Enable

UPC-E LEADING CHARACTOR

Disable

Enable

UPC-E CHECK DIGIT

Disable

Enable

End of Configuration

EAN-13 CHECK DIGIT

Disable

Enable

EAN-8 CHECEK DIGIT

Disable

Enable

ISSN/ISBN CONVERSION

Inactive

Active

READING CODE SELECTION

CODE 39 Disable

Start of Confi guration

CODE 39 Enable

ITF 2 OF 5 Disable

ITF 2 OF 5 Enable

CODABAR Enable

CODE 93 Disable

CODE 93 Enable

CODE 128 Disable

CODE 128 Enable

End of Configuration

UPC-E Disable

UPC-E Enable

EAN-13 Disable

EAN-13 Enable

EAN-8 Disable

EAN-8 Enable

UPC-A Disable

UPC-A Enable

Start of Confi guration

Matrix 25 Disable

Matrix 25 Enable

ADD HEADER AND TRAILER

HEADER

TRAILER

SET

REMOVE HEAD ER AND TRAILER

HEADER

Chinese Post Code Enable

Chinese Post Code Disable

End of Configuration

TRAILER

SET

CODE LENGTH SELECTION (Min value0) (Max value64)

SET

MIN

MAX

CODE 39

CODABAR

MIN

MAX

Start of Confi guration

CODE 93

MIN

MAX

CODE 128

MIN

MAX

MATRIX 25

MAX

MIN

ITF 2 OF 5

MIN

MAX

End of Configuration

BAR CODE ID ENTIFIER CODE SEL ECTION

Disable

Enable

Set

CODE 93

ITF 2 OF 5

UPC-E

UPC-A

EAN-13

Start of Confi guration

CODE 128

CODE 39

Chinese Post Code

Matrix 25

EAN-8

CODABAR

End of Configuration

CODE 39 IDENTIFIER CODE M

ITF 2 OF 5 IDENTIFIER CODE I

CODE 93 IDENTIFIER CODE L

UPC-E IDENTIFIER CODE E UPC-A IDENTIFIER CODE A EAN-13 IDENTIFIER CODE F

EAN-8 IDENTIFIER CODE S CODE 128 IDENTIFIER CODE N CODE 39 IDENTIFIER CODE K CHINESE POST CODE

IDENTIFIER CODE

MATRIX IDENTIFIER CODE G

PREDEFINED BAR CODE IDENTIFIERS

Start of Confi guration

NUL

SOH

STX

ACK

ENQ

EOT

ETX

BEL

APPENDIX

End of C onfiguration

CAN

ETB

SYN

NAK

DC4

DC3

DC2

DC1

DLE

Start of Confi guration

ESC

SUB

“

End of C onfiguration

)

(

‘

Start of Confi guration

;

End of C onfiguration

Start of Confi guration

End of C onfiguration

]

[

Start of Confi guration

End of C onfiguration

Start of Confi guration

}

{

DEL

34567 89123 2

901234 567892

123456 2

test

UPC-A

UPC-E

EAN-13

CODE 128

CODE 39

CODE39

123456

ITF 2 OF 5

781234 567897

ISBN

Warranty

Litele warranties this product for a period of 12 months from the date of sold, provided that the product is operated under normal proper conditions.

The warranty does not apply to any product that has beed subject to nisuse, accidental damage, unauthorized repair or tampering.

Ｌｉｔｅｌｅ

Litele LC User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual