Liquid Ears HW8900BK User Manual

ON/OFF
MUTE
RECEIVER
BATTERY
COMPARTMENT
WHAT’S INCLUDED
WIRELESS HEADPHONES
TRANSMITTER
CABLES
MICROPHONE
POWER LED
BATTERY
COMPARTMENT
ADAPTOR CABLE
AUDIO CABLE X2
RED
WHITE
TRANSMITTER
FUNCTIONS
MIC AUDIO
MONITOR WIRELESS
EARPHONE
OFF
MICROPHONE
OUTPUT
AUDIO INPUT
FUNCTION
SWITCH
MIC AUDIO
MONITOR WIRELESS
EARPHONE
OFF
CAUTION: Batteries are used. Do not dispose in fire, mix with other battery types, charge above specified rate, connect improperly, or short circuit, which may result in overheating, explosion or leakage of cell contents.
ON/OFF
MUTE
ON/OFF
MUTE
POWER LED
MUTE
(NO FUNCTION)
VOLUME / POWER DIAL
INSTALLATION
INSTALLING THE RECEIVER (HEADPHONES)
1. Insert 2 x AAA batteries (not included) into the battery compartment according to the correct polarity.
INSTALLING THE TRANSMITTER
1. Insert 2 x AAA batteries (not included) into the battery compartment according to the correct polarity.
2. Insert one end of the audio cable into the AUDIO socket on the back of the transmitter.
3. Insert other end of the audio cable into the AUDIO-OUT socket of your chosen audio source. In cases where the AUDIO-OUT socket of the audio source is not the headphone 3.5mm socket, use the supplied RCA adaptor cable for connection (see installation diagram to the right).
4. To achieve the best reception, spread out the transmitter audio cable which can also be used as an antenna.
USING YOUR HEADPHONES WITH A TV
1. Insert the transmitter audio cable into the AUDIO-OUT socket of the source. If a TV is used as the source, the TV can be muted to only output sound through the headphones.
2. Move the FUNCTION SWITCH to the WIRELESS EARPHONE position to turn on the Power LED of the transmitter.
3. Turn the VOLUME / POWER DIAL on the headphones to turn on the Power LED of the headphones.
4. The headset will automatically search for TV channel.
USING YOUR HEADPHONES WITH AN AMPLIFIER
1. Insert the transmitter audio cable into the AUDIO-OUT socket of the amplifier. Ensure the amplifier is switched ON and is generating an audio signal.
2. Move the FUNCTION SWITCH to the WIRELESS EARPHONE position to turn on the Power LED of the transmitter.
3. Turn the VOLUME / POWER DIAL on the headphones to turn on the Power LED of the headphones.
4. The headset will automatically search for amplifier channel.
USING YOUR HEADPHONES FOR WIRELESS INTERNET CHAT / GAMING
1. Connect one audio cable to the AUDIO socket of the transmitter and insert the other end of the cable into the AUDIO-OUT socket of the computer.
2. With the other audio cable, insert one end into the MIC socket of the transmitter and insert the other end into the MICROPHONE INPUT of the computer.
3. Aim the microphone socket (MIC) of the transmitter towards you then move the FUNCTION SWITCH to the WIRELESS EARPHONE position. The Power LED of transmitter will turn on.
4. Turn on the VOLUME / POWER DIAL of the headphones and the Power LED of the receiver will turn on.
5. The headset will automatically search for computer channel.
USING YOUR UNIT AS A SOUND MONITORING DEVICE
1. Place the transmitter near the area you want monitored and aim the microphone MIC towards it.
2. Move the FUNCTION SWITCH of the transmitter to the MONITOR position and the Power LED will come on.
3. Turn on the VOLUME / POWER DIAL and the Power LED of the receiver will come on.
4. Press the RESET button, then the SCAN button until the channel of your source is heard.
USING YOUR HEADPHONES WITH A CABLE (NOT WIRELESS)
1. Turn the VOLUME / POWER DIAL to OFF on the headphones.
2. Insert one end of the audio cable into the audio socket at the bottom of the headphones.
3. Insert the other end of the cable into the headphone socket of your audio source.
4. Your headphones are ready for use.
SAVING BATTERY POWER – SWITCHING OFF YOUR UNIT
Save battery power by turning off your unit when not in use:
1. Move the FUNCTION SWITCH on the transmitter to the OFF position.
2. Turn the VOLUME / POWER DIAL on the headphones to the OFF position.
3. The Power LEDs on the transmitter and headphones will turn off. Remove batteries when not in use for long periods.
A B
D
C
MIC AUDIO
MONITOR WIRELESS
EARPHONE
OFF
INSTALLING THE TRANSMITTER
CONNECTING VIA TV SIDE PANEL
(using the audio cable)
A
CONNECTING VIA TV REAR PANEL
(AUDIO OUT using the RCA adaptor cable)
B
CONNECTING VIA COMPUTER/ LAPTOP
(using the audio cable)
D
CONNECTING VIA AMPLIFIER AV RECEIVER
(using the audio cable)
C
HEADPHONE
ADAPTOR
(NOT SUPPLIED)
AUDIO OUT
R
L
RED
WHITE
TRANSMITTER
MIC AUDIO
MONITOR WIRELESS EARPHONE
OFF
1500
HW8900BK
Proudly brought to you by:
PLEASE NOTE
If your audio device does not have a 3.5mm or RCA audio output option, then you may need a digital-to-analogue converter to maximise your enjoyment from your Liquid Ears Wireless Headphones.
Did you know you can buy the item direct from The Crest Company using a credit card and have it delivered direct to your door?
Contact our helpful Customer Support team on
1800 812 261
who can recommend the right product for your needs from The Crest Company range and arrange your purchase direct.
PO Box 5658 Brendale
QLD Australia 4500
Customer Support
1800 812 261
www.crest.com.au
Smooth sound from
Loading...