Linx MS Compact, OTX--HH-CP8-MS, OTX-433-HH-CP8-MS, OTX-418-HH-CP8-MS Data Manual

Download

Page 1

MS Compact

Handheld Transmitter

Data Guide

Page 2

Table of Contents

1 Description 1 Features 1 Applications 2 Ordering Information 2 Electrical Specications 3 Theory of Operation 4 Setting the Transmitter Address 4 OTX-***-HH-CP8-MS Button Assignments 5 Contention Considerations 5 Battery Replacement 5 Assembly Diagram 6 Labeling / Instruction Requirements 8 Typical Applications 11 Resources

Warning: Some customers may want Linx radio frequency (“RF”)

products to control machinery or devices remotely, including machinery or devices that can cause death, bodily injuries, and/or property damage if improperly or inadvertently triggered, particularly in industrial settings or other applications implicating life-safety concerns (“Life and Property Safety Situations”).

NO OEM LINX REMOTE CONTROL OR FUNCTION MODULE SHOULD EVER BE USED IN LIFE AND PROPERTY SAFETY SITUATIONS. No OEM Linx Remote Control or Function Module

should be modiﬁed for Life and Property Safety Situations. Such modiﬁcation cannot provide sufﬁcient safety and will void the product’s regulatory certiﬁcation and warranty.

Customers may use our (non-Function) Modules, Antenna and Connectors as part of other systems in Life Safety Situations, but only with necessary and industry appropriate redundancies and in compliance with applicable safety standards, including without limitation, ANSI and NFPA standards. It is solely the responsibility of any Linx customer who uses one or more of these products to incorporate appropriate redundancies and safety standards for the Life and Property Safety Situation application.

Do not use this or any Linx product to trigger an action directly from the data line or RSSI lines without a protocol or encoder/ decoder to validate the data. Without validation, any signal from

another unrelated transmitter in the environment received by the module could inadvertently trigger the action.

All RF products are susceptible to RF interference that can prevent communication. RF products without frequency agility or hopping

implemented are more subject to interference. This module does not have a frequency hopping protocol built in.

Do not use any Linx product over the limits in this data guide. Excessive voltage or extended operation at the maximum voltage could cause product failure. Exceeding the reﬂow temperature proﬁle could cause product failure which is not immediately evident.

Do not make any physical or electrical modiﬁcations to any Linx product. This will void the warranty and regulatory and UL certiﬁcations

and may cause product failure which is not immediately evident.

Page 3

– –

Description

The Linx OTX-***-HH-CP8-MS Compact Handheld Transmitter is ideal for generalpurpose remote control and command applications. This unit has been pre-certiﬁed for FCC Part 15, Industry Canada, and European CE (433MHz only) compliance, reducing costs and time to market. Available in 315, 418 (standard) or

433.92MHz, this compact remote has a transmission range of up to 750 feet (230m) when combined with an LR or LT Series module. It can be conﬁgured with 1 to 8 buttons and the keypad and labeling can be customized. Ease of use and security are dramatically enhanced by an on-board MS Series encoder, which allows instant creation of up to 16,777,216 (224) unique addresses without cumbersome DIP switches or cut traces. When paired with an MS Series decoder, transmitter identity can be determined and button permissions established. The unit uses a single 3V CR2032 lithium button cell.

Features

• FCC, Canada and CE pre-certiﬁed

• 1 to 8 buttons

• Small package

• Customizable keypad

Applications

• General remote control

• Keyless entry

• Garage / gate openers

• Lighting control

• Call systems

• Home / industrial automation

MS Compact Handheld Transmitter

Data Guide

Revised 5/20/2016

2.00"

1.35"

R 0.2"

2.81"

1.62"

0.60"0.20"

FASCO

Lights

Spa

Pool

Figure 1: Package Dimensions

Figure 2: With a one-time NRE and minimum order, Linx can conﬁgure the keypad and label areas to meet your speciﬁc requirements.

Page 4

– –

2 3

Theory of Operation

The OTX-***-HH-CP8-MS Compact Handheld Transmitter combines an LR Series transmitter and an antenna with an on-board MS Series encoder to form a simple, yet highly reliable RF remote-control transmitter. The LR Series transmitter is a low-cost, high-performance synthesized ASK / OOK transmitter. The transmitter’s synthesized architecture delivers outstanding stability and frequency accuracy, while minimizing the effects of antenna port loading and mismatching. This reduces or eliminates frequency pulling, bit contraction, and other negative effects that are common to SAW-based transmitter architectures, providing a signiﬁcantly higher level of performance and reliability.

When a button is pressed on the transmitter, power is applied to the internal circuitry and the encoder is enabled. The encoder then detects the logic states of the button data lines. These states are formatted into a 2-word transmission cycle which continues until the button is released. The encoder data is used to modulate the transmitter which conveys the data into free space through the antenna. Once data is received, a decoder IC is used to check the transmitter’s address against an address saved in memory. If a match is conﬁrmed, the decoder’s outputs are set to replicate the transmitter’s button states. These outputs can then be used to activate external circuitry required by the application.

The transmitter is compatible with the LT and LR product families. For applications where range is critical, the LR Series receiver is the best choice due to its outstanding sensitivity. When the transmitter is combined with an LR Series receiver and an MS Series decoder, ranges of up to 750 feet (230m) are possible. Applications operating over shorter distances also beneﬁt from the increased link reliability and superior noise immunity provided by the LR Series receiver.

Ordering Information

Electrical Speciﬁcations

Parameter Designation Min. Typ. Max. Units Notes

Power Supply

Operating Voltage V

2.1 3.0 3.6 VDC

Supply Current l

3.4 mA

Power-Down Current l

PDN

5.0 nA 1

Transmitter Section

Transmit Frequency Range F

OTX-315-HH-CP8-MS 315 MHz

OTX-418-HH-CP8-MS 418 MHz

OTX-433-HH-CP8-MS 433.92 MHz

Center Frequency Accuracy –50 +50 kHz

Environmental

Operating Temperature Range –40 +85 °C 1

Electrical Specications

Ordering Information

Part Number Description

OTX-***-HH-CP8-MS-xxx MS Compact Handheld Transmitter

MDEV-***-HH-CP8-MS MS Compact Transmitter Master Development System

*** = 315, 418 (Standard) or 433.92MHz xxx = Custom color, leave blank for black

Figure 3: Ordering Information

1. Characterized, but not tested

Figure 4: Electrical Speciﬁcations

Page 5

– –

4 5

Setting the Transmitter Address

The MS Compact Handheld Transmitter allows the selection of one of 16,777,216 (224) unique addresses. All transmitters are supplied set to a unique address to avoid contention with other units; however, the address can be changed. This is accomplished by using a paper clip or probe to press the CREATE button on the board through the hole in the back of the case. Press the button and an LED lights up in the MODE_IND window, indicating that the address is being created. The address is randomized for as long as the button is held down. Release the button and the randomized address is saved and the LED begins ﬂashing to indicate that the Control Permissions may now be set. Press the buttons that the transmitter should have the authority to access. Press the CREATE button with the paper clip again or wait 17 seconds for it to time out. The address and Control Permissions are now set. The decoder needs to learn the address before it will accept any transmissions. Please see the Typical Applications section of this data guide or the MS Series Decoder Data Guide for details.

OTX-***-HH-CP8-MS Button Assignments

Figure 6 illustrates the relationship between the button locations and encoder data lines.

Contention Considerations

It is important to understand that only one transmitter at a time can be activated within a reception area. While the transmitted signal consists of encoded digital data, only one carrier of any particular frequency can occupy airspace without contention at any given time. If two transmitters are activated in the same area at the same time, then the signals will interfere with each other and the decoder will not see a valid transmission, so it will not take any action.

Battery Replacement

The remote unit utilizes a standard CR2032 lithium button cell. In normal use, it provides 1 to 2 years of operation. To replace the battery, remove the access cover by pressing ﬁrmly on the label area and sliding it off. Once the unit is open, remove the battery by sliding it from beneath the holder. Replace it with the same type of battery while observing the polarity shown in Figure 7.

There may be the risk of explosion if the battery is replaced by the wrong type.

Assembly Diagram

Battery access

MODE_IND Window

CREATE Button

D6 D7

D4 D5

D2 D3

D0 D1

FCC ID: OJM-OTX-XXX-CPMSA IC: 5840A-CPMSXXXA

418MHz

Figure 5: CREATE Button Access

Figure 6: OTX-***-HH-CP8-MS Button Assignments

Figure 7: Battery Access

Figure 8: OTX-***-HH-CP8-MS Assembly

Page 6

– –

6 7

Labeling / Instruction Requirements

The transmitter has been pre-certiﬁed for FCC Part 15 and Industry Canada license-exempt RSS standards for an intentional radiator. The 433.92MHz version has also been tested for CE compliance for use in the European Union. The 315MHz and 418MHz versions are not legal for use in Europe. It has already been labeled in accordance with FCC, Industry Canada and CE regulations. No further labeling of the unit is needed; however, it is necessary to include the following statement in the end product’s instruction manual or insert card. EU does not require a statement.

INSTRUCTION TO THE USER

This device complies with Part 15 of the FCC Rules and Industry Canada license-

exempt RSS standard(s). Operation of this device is subject to the following two

conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference

that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio / TV technician for help.

Theuseriscautionedthatchangesandmodicationsmadetotheequipmentwithout

the approval of manufacturer could void the user’s authority to operate this equipment.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux

appareils radioexempts de licence. L'exploitation est autorisée aux deux conditions

suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de

l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est

susceptible d'en compromettre le fonctionnement.

Page 7

– –

8 9

Typical Applications

The signal sent by the MS Compact Transmitter can be received by an LR Series receiver module or LT Series transceiver module. The outstanding sensitivity of the LR Series receiver offers the best range when used with a Linx OEM transmitter. The receiver module is then connected directly to an MS Series decoder, which decodes the received signal.

When a button is pressed on the transmitter, a corresponding line on the decoder goes high. This is then connected to external circuitry to perform whatever function is required by the application.

The decoder must learn the transmitter’s address before they can work together. This is done by taking the LEARN line on the decoder high, typically with a pushbutton switch. The MODE_IND line starts switching (if a LED is attached, this causes it to ﬂash) indicating that the decoder is in Learn Mode. Press any of the buttons on the transmitter to initiate a transmission. Take the LEARN line high again to exit Learn Mode and the system is ready for use. Figure 10 shows a schematic for a typical application.

The MS Compact Transmitter is set to 9,600bps, so SEL_BAUD0 should be tied high and SEL_BAUD1 tied low. The decoder has several unique features, such as Latch Mode, Receiver Control, and TX_ID.

If the LATCH line is tied to VCC, the outputs go high on the ﬁrst transmission, then low on the second. Figure 10 shows it tied low, so the outputs are momentary (high for as long as a signal is received that instructs the decoder to make them high).

The RX_CNTL line can be connected to the PDN line of the receiver and the decoder activates the receiver with a 10% duty cycle. This greatly reduces the average current consumption of the system. The adjacent ﬁgure shows it tied to ground, but to use this feature, connect the RX_ CNTL line of the decoder directly to the receiver’s PDN line.

The TX_ID line outputs a number associated with the originating transmitter / encoder. Application Note AN-00156 shows how to use this feature.

Data guides for the receivers, the MS encoder, and the MS decoder can be found on the Linx Technologies website at www.linxtechnologies.com.

GND

SSI

GND

SEL_BAUD

GND

LAT

RX_CNT

TX_I

MODE_IN

DATA_I

LICAL-DEC-M

S001

GND

Figure 9: Receiver and Decoder

Figure 10: LR Receiver and MS Decoder Schematic

Page 8

– –

10 11

VCC

100k

SW11SW22SW33SW44SW55SW66SW77SW88COM

SM1

100k

VCC

DPAK-X2

VCC

GND

DPAK-X2

VCC

GND

Learn

GND

LED

200

GND

100k

GND

100k

R10

100k

R11

100k

VCC

GND

R12

100k

GND

BAT-LINX2032

DPAK-X2

GND1DATA IN2GND3LADJ/VCC

RF OUT

GND6VCC

PDN

TX1

TXM-XXX-LR

GND

R13

4.7uF

D6D7SEL_BAUD

SEL_BAUD1/HS_GND

GND

KEY_IN/MS_GND

TX_CNTL

DATA_OUT

MODE_IND CREATE_ADDR

SEND

VCC

D2D3D4

LICAL-ENC-MSHS

4.7uF

10pF

R23

100k

VCC

RFIN

GND

ANT1

SPLATCH ANTENNA

GND

Set For FCC

Compliance

Figure 11: OTX-***-HH-CP8-MS Schematic Diagram

Resources

Support

For technical support, product documentation, application notes, regulatory guidelines and software updates, visit www.linxtechnologies.com

RF Design Services

For customers who need help implementing Linx modules, Linx offers design services including board layout assistance, programming, certiﬁcation advice and packaging design. For more complex RF solutions, Apex Wireless, a division of Linx Technologies, creates optimized designs with RF components and ﬁrmware selected for the customer’s application. Call +1 800 736 6677 (+1 541 471 6256 if outside the United States) for more information.

Antenna Factor Antennas

Linx’s Antenna Factor division has the industry’s broadest selection of antennas for a wide variety of applications. For customers with specialized needs, custom antennas and design services are available along with simulations of antenna performance to speed development. Learn more at www.linxtechnologies.com.

Page 9

Disclaimer

Linx Technologies is continually striving to improve the quality and function of its products. For this reason, we reserve the right to make changes to our products without notice. The information contained in this Data Guide is believed to be accurate as of the time of publication. Speciﬁcations are based on representative lot samples. Values may vary from lot-to-lot and are not guaranteed. “Typical” parameters can and do vary over lots and application. Linx Technologies makes no guarantee, warranty, or representation regarding the suitability of any product for use in any speciﬁc application. It is the customer’s responsibility to verify the suitability of the part for the intended application. NO LINX PRODUCT IS INTENDED FOR USE IN ANY APPLICATION WHERE THE SAFETY

OF LIFE OR PROPERTY IS AT RISK.

Linx Technologies DISCLAIMS ALL WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL LINX TECHNOLOGIES BE LIABLE FOR ANY OF CUSTOMER’S INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING IN ANY WAY FROM ANY DEFECTIVE OR NON-CONFORMING PRODUCTS OR FOR ANY OTHER BREACH OF CONTRACT BY LINX TECHNOLOGIES. The limitations on Linx Technologies’

liability are applicable to any and all claims or theories of recovery asserted by Customer, including, without limitation, breach of contract, breach of warranty, strict liability, or negligence. Customer assumes all liability (including, without limitation, liability for injury to person or property, economic loss, or business interruption) for all claims, including claims from third parties, arising from the use of the Products. The Customer will indemnify, defend, protect, and hold harmless Linx Technologies and its ofﬁcers, employees, subsidiaries, afﬁliates, distributors, and representatives from and against all claims, damages, actions, suits, proceedings, demands, assessments, adjustments, costs, and expenses incurred by Linx Technologies as a result of or arising from any Products sold by Linx Technologies to Customer. Under no conditions will Linx Technologies be responsible for losses arising from the use or failure of the device in any application, other than the repair, replacement, or refund limited to the original product purchase price. Devices described in this publication may contain proprietary, patented, or copyrighted techniques, components, or materials. Under no circumstances shall any user be conveyed any license or right to the use or ownership of such items.

The stylized Linx logo, Wireless Made Simple, WiSE, CipherLinx and the stylized CL logo are trademarks of Linx Technologies.

Linx Technologies

159 Ort Lane

Merlin, OR, US 97532

Phone: +1 541 471 6256

Fax: +1 541 471 6251

www.linxtechnologies.com