NTI AG / LinMot Dok-Nr. 0185-0077-E_2V1_IG_Power_Supplies_S01_72_1000
Installation Guide Power Supply
ENG
Power range 1000 W
Type S01-72/1000
Installation Guide Power Supply ENG
Page 2 / 12 Power range 1000 W NTI AG / LinMot
Content
1 General information ................................................................................................................................. 3
1.1 Introduction ........................................................................................................................................ 3
1.2 Explanation of symbols ...................................................................................................................... 3
1.3 Qualified personnel ............................................................................................................................ 3
1.4 Liability ............................................................................................................................................... 3
1.5 Copyright............................................................................................................................................ 3
2 Safety instructions ................................................................................................................................... 4
3 Technical Data .......................................................................................................................................... 5
4 Operating data .......................................................................................................................................... 6
5 Mechanics ................................................................................................................................................. 6
5.1 Connection ......................................................................................................................................... 6
5.2 Mounting ............................................................................................................................................ 7
6 Explanation of symbols ........................................................................................................................... 7
7 Notes .......................................................................................................................................................... 8
7.1 Context between powerboost time and minimum break time ............................................................ 8
7.2 Current limiting characteristic ............................................................................................................ 8
8 Dimensions ............................................................................................................................................... 9
9 International Certificates ......................................................................................................................... 9
10 Declaration of Conformity and CE-marking .................................................................................... 10
11 CB Test Certificate ............................................................................................................................. 11
Installation Guide Power Supply ENG
NTI AG / LinMot Power range 1000 W Page 3 / 12
1 General information
1.1 Introduction
Please observe the following safety instructions, the instructions on the appliance (the term "appliance"
relates to a single power supply assembly) and the detailed data sheet to avoid any risk of personal injury or
damage to the appliance or to other equipment which may be connected.
1.2 Explanation of symbols
Triangular warning symbols warn against a danger.
Round command symbols tell what to do.
1.3 Qualified personnel
All work such as transport, installation, commissioning and service is only allowed to be carried out by
qualified personnel. Qualified personnel in the sense of the safety instructions in this documentation are
persons who are familiar with the transport, installation, assembly, commissioning and operation of the
product and who have the appropriate qualifications.
This manual must be read carefully before transport, installation, commissioning, service and all safetyrelated information must be adhered to.
1.4 Liability
NTI AG (as manufacturer of LinMot linear motors and MagSpring products) excludes all liability for damages
and expenses caused by incorrect use of the products. This also applies to false applications, which are
caused by NTI AG's own data and notes, for example in the course of sales, support or application activities.
It is the sole responsibility of the user to check the information and information provided by NTI AG regarding
their safety-relevant correctness. In addition, the entire responsibility for safety-related product functionality
lies exclusively with the user.Product warranties are void if products are used with stators, sliders, servo
drives or cables not manufactured by NTI AG unless such use was specifically approved by NTI AG.
NTI AG’s warranty is limited to repair or replacement as stated in our standard warranty policy as described
in our "terms and conditions" previously supplied to the purchaser of our equipment (please request copy of
same if not otherwise available). Further reference is made to our general terms and conditions.
1.5 Copyright
This work is protected by copyright.
Under the copyright laws, this publication may not be reproduced or transmitted in any form, electronic or
mechanical, including photocopying, recording, microfilm, storing in an information retrieval system, not even
for training purposes, or translating, in whole or in part, without the prior written consent of NTI AG.
LinMot® is a registered trademark of NTI AG.
Installation Guide Power Supply ENG
Page 4 / 12 Power range 1000 W NTI AG / LinMot
2 Safety instructions
Do not open!
Do not use without a PE connection.
Disconnect power before installing or removing.
For built-in use only!
This warning also applies in the event that an internal fuse blows in the appliance.
The appliance should generally only be opened and/or repaired by the manufacturer.
Appliances are approved for operation based on the connected loads and technical data
stated on the rating plate and the detailed data sheet only. Please read these carefully
before installing the appliance and commencing operation and take note of any
performance limitations, such as reduced output power (derating) in the event of high
ambient temperatures.
All appliances must be connected to a mains supply offering voltage quality which complies
with EN50160 standards. Operating the appliance via UPSs, current inverters etc. which do
not meet these standards may result in damage to the appliance. In such cases, no
guarantee claims will be accepted.
As a rule, appliances are intended for built-in use. They must be installed and connected by
qualified personnel.
Ensure that the surrounding casing protects the appliance against fire!
Heat loss occurs during operation of the appliance. To ensure safe performance and avoid
any possible risk of damage to the assembly itself and/or connected equipment, provision
must be made for adequate heat dispersal. Please observe the relevant instructions in this
document and the appliance.
Please take note of the information shown on the connection and pin configurations for this
appliance! Pay particular attention to the information on the wire cross-section and torque
and ensure that the wiring complies with prevailing standards.
If a load output is designed to take sensor cables, these must be connected to the
corresponding load lines to ensure safe operation of the appliance.
Appliances may be connected in parallel if this option is given in the technical data; max.
three identical appliances, otherwise please consult LinMot. Advice should normally be
obtained from LinMot before connecting appliances in series.
Trim potentiometers may not be used on appliances unless the relevant setting range is
given in the technical data and on the appliance, and the maximum output power is not
exceeded.
All appliances have been tested for compliance with the prevailing insulation and highvoltage standards. Any additional tests of this kind which may be required should not be
carried out without the consent of the appliance manufacturer, LinMot. As there could be a
potential risk of damaging or destroying components in the appliance, it may be necessary
to take special precautions prior to such tests.
Installation Guide Power Supply ENG
NTI AG / LinMot Power range 1000 W Page 5 / 12
3 Technical Data
S01-72/1000
Input
Input voltage range
AC 3 x 340-550V
Power frequency
50/60Hz
Efficiency
typ. 91,5%
Input current limitation
< 35A
peak
typ. in cold state, < 70A
peak
in hot state
Internal fuse
3 x 6.3AT
External branch circuit
16A (IEC), 20A (USA) necessary
Output
Preset range Vo
56 - 80VDC
factory setting Vo
nom
± 0,15/0,2V
Max. output power
1000W
Powerboost > 0.5s - 2s
boost break necessary, see diagram in chapter 7
Powerboost < 0.5s
no boost break necessary, but the boost time in the last 4s may not be
longer as 2s, otherwise a boost break 1min is necessary (boostbreak
<25ms will be not recognized)
Operation indicator
green LED for Vo, red LED for error
Ripple
40mVss typ.
Noise voltage
200mVss typ.
Temperature coefficient
≤ 0,025% / K
Switch on / switch off
No Vo overshoot (soft-start)
Start-up delay
250 ms typ.
Rise time
20ms typ./155ms typ.bei 50.000 μF Last
Back feeding voltage
approx. 100VDC
Serial connection
yes, max. 2 identical power supplies
Parallel connection
yes, max. 3 identical power supplies
Regelung
Line regulation
< 0.3% for Vo at Ue
min
- Ue
max
Load regulation
< 0,5% for Vo at Io 0 - 100% single operation
< 3% for Vo at Io 0 - 100% parallel operation
Response time
typ. 1ms at Io 20 - 80%
Protection and Controlling
Overvoltage protection (OVP)
approx. 87V
automatical repeating
Current limitation
see diagramm, output permanent short-circuit proof
Overtemperature
Switches off if inside temperature becomes
to high, reconnection with hysteresis
Mains buffering
11 ms typ. in normal operation
Relay contact
Relay contact (<80V/0.2A), changing
at Vo < 37 / 52V from OK to FAIL
Control signal OFF
external switch-off with 5 - 63VDC/5mA
min
or switch from Vo
Installation Guide Power Supply ENG
Page 6 / 12 Power range 1000 W NTI AG / LinMot
Safety / Standards
EN 60950-1 / IEC 60950-1 / VDE 0160 safety class I / VDE 0100
/ IP20 CSA-C22.2 No 107 / CSA-C22.2 No. 60950-1-03 UL Std.
60950-1 / UL Std. 508 (Operation in Delta mains only for UL508)
EMC
Flicker
EN 61000-3-3
Interference suppression /
Interference immunity
EN 61000-6-2 / EN 61204-3
ESD
EN 61000-4-2 8/15 kV
Electrical fields
EN 61000-4-3 Noise level 10V/m
Burst
Input: EN 61000-4-4 4kV / Output: EN 61000-4-4 2kV
Surge
Input: EN 61000-4-5 2/4kV / Output: EN 61000-4-5 0,5kV
HF Immunity
EN 61000-4-6 noise level 10V
Voltage drop
EN 61000-4-11
Interference emission
EN 61000-6-3 / EN 61204-3 / EN 55022 / EN 55011 class B
Radiation depends on assembly
Weight
2.0 kg
4 Operating data
Temperature range
-25°C...70°C integral, temperature controlled fan,air intake bottom-up (fan swichted
on/off in two steps dependent on temperature)
Derating
2% / K at +60°C
Operation in any assembly position possible. The distance between the surrounding
components and the air admission and air exit holes should be at least 50 mm.
Please ensure that exhaust air is not immediately sucked in again.
Ensure that the surrounding casing protects the appliance against fire!
Protect the products against moisture, humidity, condensation and dirt.
5 Mechanics
5.1 Connection
Main input: 4-pole
1,5 - 4 mm² strand/wire
Min. tightening torque: 0,5Nm
Load output: 5-pole
2,5 - 4 mm² strand/wire
Min. tightening torque: 0,5Nm
Control signals: 4-pole
0,5 - 1,5 mm² strand/wire
Min. tightening torque: 0,22Nm
Installation Guide Power Supply ENG
NTI AG / LinMot Power range 1000 W Page 7 / 12
5.2 Mounting
All devices can be attached to a back wall using the mounting tabs (see dimensions chapter 8). Operation in
any assembly position possible. The distance between the surrounding components and the air admission
and air exit holes should be at least 50 mm.
Please ensure that exhaust air is not immediately sucked in again.
6 Explanation of symbols
PE Protective conductor
Do not use supply without PE connection!
L1 / L2 / L3 Mains phases
+ / - Load connection
Relay OK/FAIL Monitoring connections
OFF Control connection
Installation Guide Power Supply ENG
Page 8 / 12 Power range 1000 W NTI AG / LinMot
7 Notes
7.1 Context between powerboost time and minimum break time
7.2 Current limiting characteristic
Start-up takes place with power boost between 190% and 210% of the nominal current for a period of
approx. 2s. You can use power boost also in running operation.
Installation Guide Power Supply ENG
NTI AG / LinMot Power range 1000 W Page 9 / 12
8 Dimensions
in mm
9 International Certificates
Installation Guide Power Supply ENG
Page 10 / 12 Power range 1000 W NTI AG / LinMot
10 Declaration of Conformity and CE-marking
Wir
We
Nous NTI AG
Bodenaeckerstrasse 2
8957 Spreitenbach
erklären in alleiniger Verantwortung, dass das Produkt
declare under our sole responsibility that the product
declarons sous notre seule responsabilité que le produit
Produkt
Art-Nr.
Schaltnetzteil 72V/1000W, 3x340-550VAC
0150-1872
konform ist mit den Anforderungen der Richtlinien,
is conform to the provisions of directives,
est conformé aux exigences des directives,
2014/35/EU (LVD) + 2014/30/EU (EMCD)
gestützt auf die folgenden Normen,
based on the following standards,
base aux normes suivants,
EMCD EN61000-6-2:2005
EN61000-6-3:2007 + A1:2011
SAFETY IEC 60950-1:2005 (second edition) + A1:2009 + A2:2013
EN 60950-1:2006 + A11:2009 + A1:2010 + AC:2011 + A12:2011 +
A2:2013
Jahr der CE-Kennzeichnung:
Year of CE marking:
Annee du marquage CE: 2017
Spreitenbach, 17.08.2018
Dr.-Ing. Ronald Rohner
CEO NTI AG
Installation Guide Power Supply ENG
NTI AG / LinMot Power range 1000 W Page 11 / 12
11 CB Test Certificate
© 2019 NTI AG / LinMot Subject to alterations
ALL LINEAR MOTION
FROM A SINGLE SOURCE
Visit http://www.linmot.com/ to find a distributor next to you.
LinMot Europe
NTI AG - LinMot & MagSpring
Bodenaeckerstrasse 2
CH-8957 Spreitenbach
Sales / Administration: +41-(0)56-419 91 91
office@linmot.com
Tech. Support: +41-(0)56-544 71 00
support@linmot.com
Tech. Support (Skype): skype:support.linmot
Fax: +41-(0)56-419 91 92
Web: http://www.linmot.com/
LinMot USA
LinMot USA, Inc.
N1922 State Road 120, Unit 1
Lake Geneva, WI 53147
Sales / Administration : 262-743-2555
E-Mail: usasales@linmot.com
Web: http://www.linmot-usa.com/
Loading...